Refine
Year of publication
Is part of the Bibliography
- yes (186)
Keywords
Institute
- Institut für Physik und Astronomie (186) (remove)
The influence of chemical composition and crystallisation conditions on the ferroelectric and paraelectric phases and the resulting morphology in Poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) (P(VDF-TrFE-CFE)) terpolymer films with 55.4/37.2/7.3 mol% or with 62.2/29.4/8.4 mol% of VDF/TrFE/CFE was studied. Poly(vinylidene fluoride trifluoroethylene) (P(VDF-TrFE)) with 75/25 mol% VDF/TrFE was employed as reference material. Fourier-Transform Infrared Spectroscopy (FTIR) was used to determine the fractions of the relevant terpolymer phases, and X-Ray Diffraction (XRD) was employed to assess the crystalline morphology. The FTIR results show an increase of the fraction of paraelectric phases after annealing. On the other hand, XRD results indicate a more stable paraelectric phase in the terpolymer with higher CFE content.
Published results on LDPE/MgO nanocomposites (3wt%) show that they promise to be good electrical-insulation materials. In this work, the nanocomposites are examined as a potential (ferro-)electret material as well. Isothermal surface-potential decay measurements show that charged LDPE/MgO films still exhibit significant surface potentials after heating for 4 hours at 80 degrees C, which suggests good capabilities of LDPE/MgO nanocomposites to hold electric charges of both polarities. Open-tubular-channel ferroelectrets prepared from LDPE/MgO nanocomposite films show significant piezoelectricity with d(33) coefficients of about 20 pC/N after charging and are stable up to temperatures of at least 80 degrees C. Thus LDPE/MgO nanocomposites may become available as a new ferroelectret material. To increase their d(33) coefficients, it is desirable to optimize the charging conditions and the ferroelectret structure.
The present work is part of a collaborative H2020 European funded research project called SENSKIN, that aims to improve Structural Health Monitoring (SHM) for transport infrastructure through the development of an innovative monitoring and management system for bridges based on a novel, inexpensive, skin-like sensor. The integrated SENSKIN technology will be implemented in the case of steel and concrete bridges, and tested, field-evaluated and benchmarked on actual bridge environment against a conventional health monitoring solution developed by Mistras Group Hellas. The main objective of the present work is to implement the autonomous, fully functional strain monitoring system based on commercially available off-the-shelf components, that will be used to accomplish direct comparison between the performance of the innovative SENSKIN sensors and the conventional strain sensors commonly used for structural monitoring of bridges. For this purpose, the mini Structural Monitoring System (mini SMS) of Physical Acoustics Corporation, a comprehensive data acquisition unit designed specifically for long-term unattended operation in outdoor environments, was selected. For the completion of the conventional system, appropriate foil-type strain sensors were selected, driven by special conditioners manufactured by Mistras Group. A comprehensive description of the strain monitoring system and its peripheral components is provided in this paper. For the evaluation of the integrated system’s performance and the effect of various parameters on the long-term behavior of sensors, several test steel pieces instrumented with different strain sensors configurations were prepared and tested in both laboratory and field ambient conditions. Furthermore, loading tests were performed aiming to validate the response of the system in monitoring the strains developed in steel beam elements subject to bending regimes. Representative results obtained from the above experimental tests have been included in this paper as well.
The Bow on a String
(2018)
The interaction between a bowed string instrument and its player is conveyed by the bow, the vibrational properties of which can be measured either separately on the bow or during the bowing procedure. Here, two piezoelectric film sensors, made of a ferroelectret material, are installed on a violin bow, one sensor at the tip and one at the frog. With these sensors, a violin is played under normal conditions, and the signals are analysed. The features in the resulting spectrograms are identified as string harmonics and longitudinal bow-hair resonances. The bow-hair sections on both sides of the bow-string contact exhibit separate resonances which are observed as absorption dips in the spectra. Owing to the sensor positions at the bow-hair terminations, it can be inferred that the two bow-hair sections act as mutual vibration absorbers. From a regression of the observed resonances, the longitudinal bow-hair velocity can be obtained. With additional film sensors under the violin bridge, body vibrations were also detected providing further details of the coupling mechanisms.
Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor by means of molecular-layer deposition. The treatment leads to considerable improvements of the electret-charge stability on positively charged films. A slight improvement is also observed for negatively charged films. In line with our previous findings, we attribute the improvement in electret properties to the formation of deeper traps on the chemically modified polymer surfaces. Here, we investigate the influence of the charge density on electret stability of FEP films with modified surfaces. Trap-energy spectra obtained from thermally-stimulated-discharge measurements indicate that the charge stability on modified FEP films depends on how the surface traps are populated and on the availability of additional deeper traps.
Polymer foams are in industrial use for several decades. More recently, non-polar polymer foams were found to be piezoelectric (so-called piezoelectrets) after internal electrical charging of the cavities. So far, few studies have been carried out on the electrical-insulation properties of polymer foams. Here, we compare the piezoelectric and the DC-voltage electrical-insulation properties of cellular polypropylene (PP) foams. Their cavity microstructure can be adjusted via inflation in high-pressure nitrogen gas in combination with a subsequent thermal treatment. While inflation is effective for improving the piezoelectricity, it is detrimental for the electrical-insulation properties. The original cellular PP foam shows a breakdown strength of approximately 230 MV/m, within the same range as that of solid PP. The breakdown strength decreases with increasing degree of inflation, and the dependence on the foam thickness follows an inverse power law with an exponent of 1.2. Nevertheless, up to a thickness of 140 mu m (3.5 times the original thickness), the breakdown strength of cellular-foam PP films is at least 7 times that of an air gap with the same thickness. In addition, the influence of high temperatures and high humidities on the piezoelectricity and the breakdown strength of cellular PP was studied. It was found that the piezoelectric d(33) coefficient decays rapidly already at 70 degrees C, while the breakdown strength slightly increases during storage at 70 or 90 degrees C. Under a relative humidity of 95%, the breakdown strength increases with storage time, while the piezoelectric d(33) coefficient slightly decreases.
Dielectric relaxation processes and structural transitions in Poly(vinylidenefluoride-trifluoroethylene-chlorofluoroethylene) (P(VDF-TrFE-CFE)) terpolymer films with two different monomer compositions were investigated in comparison with Poly(vinylidenefluoride-trifluoroethylene) (P(VDF-TrFE)) copolymer films as reference material. Differential Scanning Calorimetry was employed to assess annealing effects on phase transitions and crystalline structure, while relaxation processes were investigated by means of Dielectric Relaxation Spectroscopy, the results of which indicate the existence of two separate dispersion regions, denoted as processes A and B, respectively. Process A appears at a certain temperature independent of frequency, but is strongly influenced by the crystallisation temperature and the CFE content, while peak B shows typical features of a relaxation process and is less influenced by crystallisation temperature and CFE content. Furthermore, peak B is related to the glass transition which is more pronounced in the terpolymer than in P(VDF-TrFE). A closer analysis indicates that the addition of CFE and thermal annealing gradually shift the ferro-to-paraelectric transition in P(VDF-TrFE) to lower temperatures, while the phase transition is transformed more and more into a relaxation.
Nowadays, structural health monitoring of critical infrastructures is considered as of primal importance especially for managing transport infrastructure however most current SHM methodologies are based on point-sensors that show various limitations relating to their spatial positioning capabilities, cost of development and measurement range. This publication describes the progress in the SENSKIN EC co-funded research project that is developing a dielectric-elastomer sensor, formed from a large highly extensible capacitance sensing membrane and is supported by an advanced micro-electronic circuitry, for monitoring transport infrastructure bridges. The sensor under development provides spatial measurements of strain in excess of 10%, while the sensing system is being designed to be easy to install, require low power in operation concepts, require simple signal processing, and have the ability to self-monitor and report. An appropriate wireless sensor network is also being designed and developed supported by local gateways for the required data collection and exploitation. SENSKIN also develops a Decision-Support-System (DSS) for proactive condition-based structural interventions under normal operating conditions and reactive emergency intervention following an extreme event. The latter is supported by a life-cycle-costing (LCC) and life-cycle-assessment (LCA) module responsible for the total internal and external costs for the identified bridge rehabilitation, analysis of options, yielding figures for the assessment of the economic implications of the bridge rehabilitation work and the environmental impacts of the bridge rehabilitation options and of the associated secondary effects respectively. The overall monitoring system will be evaluated and benchmarked on actual bridges of Egnatia Highway (Greece) and Bosporus Bridge (Turkey).
In the present study, the charge distribution and the charge transport across the thickness of 2- and 3-dimensional polymer nanodielectrics was investigated. Chemically surface-treated polypropylene (PP) films and low-density polyethylene nanocomposite films with 3 wt % of magnesium oxide (LDPE/MgO) served as examples of 2-D and 3-D nanodielectrics, respectively. Surface charges were deposited onto the non-metallized surfaces of the one-side metallized polymer films and found to broaden and to thus enter the bulk of the films upon thermal stimulation at suitable elevated temperatures. The resulting space-charge profiles in the thickness direction were probed by means of Piezoelectrically-generated Pressure Steps (PPSs). It was observed that the chemical surface treatment of PP which led to the formation of nano-structures or the use of bulk nanoparticles from LDPE/MgO nanocomposites enhance charge trapping on or in the respective polymer films and also reduce charge transport inside the respective samples.
Dielectric materials for electro-active (electret) and/or electro-passive (insulation) applications
(2019)
Dielectric materials for electret applications usually have to contain a quasi-permanent space charge or dipole polarization that is stable over large temperature ranges and time periods. For electrical-insulation applications, on the other hand, a quasi-permanent space charge or dipole polarization is usually considered detrimental. In recent years, however, with the advent of high-voltage direct-current (HVDC) transmission and high-voltage capacitors for energy storage, new possibilities are being explored in the area of high-voltage dielectrics. Stable charge trapping (as e.g. found in nano-dielectrics) or large dipole polarizations (as e.g. found in relaxor ferroelectrics and high-permittivity dielectrics) are no longer considered to be necessarily detrimental in electrical-insulation materials. On the other hand, recent developments in electro-electrets (dielectric elastomers), i.e. very soft dielectrics with large actuation strains and high breakdown fields, and in ferroelectrets, i.e. polymers with electrically charged cavities, have resulted in new electret materials that may also be useful for HVDC insulation systems. Furthermore, 2-dimensional (nano-particles on surfaces or interfaces) and 3-dimensional (nano-particles in the bulk) nano-dielectrics have been found to provide very good charge-trapping properties that may not only be used for more stable electrets and ferroelectrets, but also for better HVDC electrical-insulation materials with the possibility to optimize charge-transport and field-gradient behavior. In view of these and other recent developments, a first attempt will be made to review a small selection of electro-active (i.e. electret) and electro-passive (i.e. insulation) dielectrics in direct comparison. Such a comparative approach may lead to synergies in materials concepts and research methods that will benefit both areas. Furthermore, electrets may be very useful for sensing and monitoring applications in electrical-insulation systems, while high-voltage technology is essential for more efficient charging and poling of electret materials.