Refine
Has Fulltext
- no (21)
Language
- English (21)
Is part of the Bibliography
- yes (21)
Keywords
Institute
The electret state stability in nonpolar semicrystalline polymers is largely determined by the traps located at crystalline/ amorphous phase interfaces. Thus, the thermal history of such polymers should considerably influence their electret properties. In the present work, we investigate how recrystallization influences charge stability in low-density polyethylene corona electrets. It has been found that electret charge stability in quenched samples is higher than in slowly-crystallized ones. Phenomenologicaly, this can be explained by the increased number of deeper traps in samples with smaller crystallite size.
Chemical and physical surface modification of PTFE films-an approach to produce stable electrets
(2012)
The thermal stability of positive charge has been investigated in chemically and physically treated polytetrafluoroethylene (PTFE) films. It has been found that virgin films, oriented by the manufacturer, display an increase in thermal stability of positive charge with an increase of the initial value of surface potential. Such an anomalous behavior is explained by the influence of a negative tribocharge, trapped some small distance below the surface. In PTFE samples treated with orthophosphoric acid and with tetraethoxysilane, a considerable improvement of positive charge stability has been achieved, but no influence of the initial value of surface potential has been observed. However, this influence should be kept in mind when comparing charge stability in virgin and modified samples. In nonoriented PTFE films, no influence of the initial value of surface potential on charge stability has been observed. This could be due to the fact that these films did not possess a noticeable negative tribocharge. After the treatment in glow-discharge defluorination, oxidation and appearance of polar groups have been detected on the surface. These changes in chemical composition of a PTFE surface resulted in a noticeable improvement in thermal stability of positively charged electrets. This improvement is attributed to the formation of deeper traps on the modified surface.
This paper investigates the effect of chemical surface modification of polytetrafluoroethylene (PTFE) and low density polyethylene (LDPE) films on their electret properties. PTFE films were subjected to wet treatment with three different chemicals: orthophosphoric acid, tetrabutyl titanate and tetraethoxysilane. The technique based on the principles of molecular layer deposition (MLD) method was used to modify the surface of LDPE films with phosphorus trichloride vapors. The surfaces of the films were then corona charged, and the electret charge stability was studied by means of isothermal and thermally stimulated surface potential decay. Both PTFE and LDPE films, after the surface treatment, displayed a considerable enhancement in the charge stability compared to the virgin samples. It is important to note that the enhancement of the charge stability was achieved in the positively charged PTFE films, a result important to practical applications. We attribute this effect of charge stabilization to the formation of new energetically deep traps on the modified surface. Decrease in molecular mobility, due to attachment of new chemical structures to the surface macromolecules, may also contribute to the overall growth of the charge stability.
Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor in a molecular-layer deposition process. As a result of the surface treatment, significant improvements of the thermal and temporal charge stability were observed. Charge-decay measurements revealed enhancements of the half-value temperatures and the relaxation times of positively charged FEP electrets by at least 120 A degrees C and two orders of magnitude, respectively. Beyond previous publications on fluoropolymer electrets with surface modification, we here report enhanced charge stabilities of the FEP films charged in negative as well as in positive corona discharges. Even though the improvement for negatively charged FEP films is moderate (half-value temperature about 20 A degrees C higher), our experiments show that the asymmetry in positive and negative charge stability that is typical for FEP electrets can be overcome by means of chemical surface treatments. The results are discussed in the context of the formation of modified surface layers with enhanced charge-trapping properties.
Enhanced electret charge stability on Polyethylene Films treated with Titanium-Tetrachloride vapor
(2012)
Low-density polyethylene (LDPE) films have been treated with titanium-tetrachloride vapor by means of the molecular-layer-deposition method. It is shown that such a treatment leads to a considerable improvement of the electret properties for both positively and negatively charged films. The temperature stability of the electret homo-charge has been increased by approximately 60 degrees C. At the same time, the temporal stability of charge is also considerably improved. Modified low-density polyethylene films show no "cross-over phenomenon" when charged to higher voltages. Thus, it is now possible to produce electrets from polyethylene films with high initial charge densities, but without a strongly reduced charge stability. The influence of a chemical treatment with titanium-tetrachloride vapor on charge injection from aluminum electrodes into polyethylene films was also investigated. It is found that the interface between an aluminum electrode and a modified LDPE surface layer has different injection properties for positive and negative charges. Electrons can be injected across the modified interface, whereas injection of holes is either very limited or non-existent.
Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor by means of molecular-layer deposition. The treatment leads to considerable improvements of the electret-charge stability on positively charged films. A slight improvement is also observed for negatively charged films. In line with our previous findings, we attribute the improvement in electret properties to the formation of deeper traps on the chemically modified polymer surfaces. Here, we investigate the influence of the charge density on electret stability of FEP films with modified surfaces. Trap-energy spectra obtained from thermally-stimulated-discharge measurements indicate that the charge stability on modified FEP films depends on how the surface traps are populated and on the availability of additional deeper traps.
In ferroelectrets, the piezoelectricity stems from the charges of both polarities trapped on the inner surfaces of the cavities in the material, so that its thermal stability is defined by the stability of the respective charges. In the present work, a template-based lamination technique has been employed to fabricate tubular-channel ferroelectrets from fluoroethylenepropylene (FEP) films. It has been shown that the piezoelectricity in FEP ferroelectrets decays at relatively low temperatures due to the inherently lower thermal stability of the positive charge. In order to improve charge trapping, we have treated both FEP films and inner surfaces of the ferroelectret cavities with titanium-tetrachloride vapor, using the atomic-layer-deposition technique. Using surface-potential-decay measurements on FEP films, we have found that the charge-decay curves shift by more than 100 degrees C to the higher temperatures as a result of the surface treatment. Direct measurements of piezoelectric d(33) coefficients as a function of temperature have shown that the piezoelectric stability is likewise improved with the d(33)-decay curves shifted by 60 degrees C to the right. The improvement of electret/ferroelectret properties can be attributed to the formation of the deeper traps on the chemically modified FEP surface. SEM micrographs and EDS analysis reveal island-like structures with titanium- and oxygen-containing species that can be responsible for the deeper trapping of the electret charges. Published by AIP Publishing.
The use of nanoparticles in polymer composite dielectrics has promised great improvements, but useful results have been elusive. Here, the importance of the interfacial interactions between the nanoparticles and the polymer matrix are investigated in TiO2 nanocomposites for dielectric materials using surface functionalisation. The interface is observed to dominate the nanocomposite properties and leads to a threefold increase in permittivity at volume fractions as low as 10%. Surface functionalisation of the filler nanoparticles with silanes allows control of this interface, avoiding significant degradation of the other important material properties, particularly electrical breakdown strength, and resulting in a material that is demonstrated successfully as an active material in a dielectric elastomer actuator application with increased work output compared to the pure polymer. Although further permittivity increases are observed when the interface regions have formed a percolation network, the other material properties deteriorate. The observation of percolation behaviour allows the interface thickness to be estimated.
In the present study, the charge distribution and the charge transport across the thickness of 2- and 3-dimensional polymer nanodielectrics was investigated. Chemically surface-treated polypropylene (PP) films and low-density polyethylene nanocomposite films with 3 wt % of magnesium oxide (LDPE/MgO) served as examples of 2-D and 3-D nanodielectrics, respectively. Surface charges were deposited onto the non-metallized surfaces of the one-side metallized polymer films and found to broaden and to thus enter the bulk of the films upon thermal stimulation at suitable elevated temperatures. The resulting space-charge profiles in the thickness direction were probed by means of Piezoelectrically-generated Pressure Steps (PPSs). It was observed that the chemical surface treatment of PP which led to the formation of nano-structures or the use of bulk nanoparticles from LDPE/MgO nanocomposites enhance charge trapping on or in the respective polymer films and also reduce charge transport inside the respective samples.
A template-based lamination technique for the manufacture of ferroelectrets from uniform electret films was recently reported. In the present work, this technique is used to prepare similar ferroelectret structures from low-density polyethylene (LDPE) films and from fluoro-ethylene-propylene (FEP) copolymer films. A comparative analysis of the pressure-, temperature-, and frequency-dependent piezoelectric properties has been performed on the two ferroelectret systems. It is observed that the FEP ferroelectrets exhibit better piezoelectric responses and are thermally more stable. The difference between the piezoelectric d(33) coefficients of the two ferroelectret systems is partially explained here by their different elastic moduli. The anti-resonance peaks of both structures have been investigated by means of dielectric resonance spectroscopy and electroacoustic sound-pressure measurements. A difference of more than 10 kHz is observed between the anti-resonance frequencies of the two ferroelectret systems.