Refine
Keywords
- CuO (1)
- NiTi (1)
- gas sensing (1)
- hydrogel (1)
- inner surface (1)
- ionic liquid precursors (1)
- ionic liquids (1)
- magnetic nanoparticles (1)
- mesoporous materials (1)
- nanoparticles (1)
Institute
- Institut für Chemie (14) (remove)
A series of new 2 2'-bipyridine/1 2-dithiolate transition metal complexes has been synthesised and characterised As 1,2-dithiolate ligands 1,2 dithiooxalate (dto) and 1 2-dithiosquarate (dtsq) were used It follows from the IR spectra that the multidentate dithiolate ligands coordinate exclusively via their sulfur atoms forming an MN2S2 coordination sphere The central metal ions (M) are Cu2+ Ni2+ Pd2+ Pt2+, and Zn2+ The complex [Cu-II(bpy)(dto)] could be studied by EPR spectroscopy and was measured as powder diamagnetically diluted in the isostructural [Ni-II(bpy)(dto)] host structure The spin density contribution calculated from the experimental parameters is compared with the electronic situation in the frontier orbitals namely in the semi occupied SOMO of the copper complex derived from quantum chemical calculations on different levels (EHT and DFT)
The paper is focused on the characterization and use of phosphatidylcholine (PC)-based inverse microemulsions as a template phase for the CdS nanoparticle formation. The optically clear, isotropic phase in the oil corner was identified as a "classicalö water-in-oil microemulsion by means of NMR-diffusion measurements. Because of the very small dimensions of the water droplets, the isotropic phase shows a Newtonian-like flow behavior, and adequate amounts of bulk water cannot be detected by DSC. It is demonstrated that this w/o microemulsion can be used successfully as a nanoreactor for the formation of CdS nanoparticles with diameters of 4-5 nm. During the following process of solvent evaporation the individual small CdS nanoparticles aggregate to significant larger cubic nanoparticles, with an edge length of 2-40 nm, arranged in well-defined mosaic-like superstructures. In presence of SDS the nanocubes were stable up to 800 °C. It has to be stated here that polyelectrolytes prevent the formation of such well-ordered superstructures.
Narrow channels with polar walls are the structural and functional features responsible for the high capacity of a zinc-organic framework based on an imidazolate-amide-imidate ligand for the uptake of H2 and CO2 (see structure: orange Zn, blue N, red O, dark gray C, light gray H). The rigid and stable chelating ligand was synthesized in situ by partial hydrolysis of a dicyanoimidazole compound.
The sensing potential of CuO nanoparticles synthesized via. precipitation from a water/ionic liquid precursor (ILP) mixture was investigated. The particles have a moderate surface area of 66 m(2)/g after synthesis, which decreases upon thermal treatment to below 5 m(2)/g. Transmission electron microscopy confirms crystal growth upon annealing, likely due to sintering effects. The as-synthesized particles can be used for ethanol sensing. The respective sensors show fast response and recovery times of below 10 s and responses greater than 2.3 at 100 ppm of ethanol at 200 degrees C, which is higher than any CuO-based ethanol sensor described so far.
One of the main issues with the use of nickel titanium alloy (NiTi) implants in cardiovascular implants (stents) is that these devices must be of very high quality in order to avoid subsequent operations due to failing stents. For small stents with diameters below ca. 2 mm, however, stent characterization is not straightforward. One of the main problems is that there are virtually no methods to characterize the interior of the NiTi tubes used for fabrication of these tiny stents. The current paper reports on a robust hybrid actuator for the characterization of NiTi tubes prior to stent fabrication. The method is based on a polymer/hydrogel/magnetic nanoparticle hybrid material and allows for the determination of the inner diameter at virtually all places in the raw NiTi tubes. Knowledge of the inner structure of the raw NiTi tubes is crucial to avoid regions that are not hollow or regions that are likely to fail due to defects inside the raw tube. The actuator enables close contact of a magnetic polymer film with the inner NiTi tube surface. The magnetic signal can be detected from outside and be used for a direct mapping of the tube interior. As a result, it is possible to detect critical regions prior to expensive and slow stent fabrication processes.