Refine
Has Fulltext
- no (172)
Year of publication
Document Type
- Article (172) (remove)
Is part of the Bibliography
- yes (172)
Keywords
- piezoelectret (3)
- piezoelectrets (3)
- Curie transition (2)
- Electrets (2)
- Ferroelectrets (2)
- P(VDF-TrFE-CFE) terpolymer (2)
- charge-carrier transport (2)
- chemical modification (2)
- dielectric barrier discharge (DBD) (2)
- dielectric properties (2)
Institute
Electrically charged cellular polymer films can exhibit very high piezoelectric activity and are therefore more and more often employed in advanced electromechanical and electro-acoustical transducers. In this paper, we report an optimized sequence of steps for preparing such ferroelectrets from commercial nonvoided ploy(ethylene terephthalate) (PETP) films by means of foaming with CO2 biaxial mechanical stretching, controlled void inflation, and bipolar electric charging. The nonvoid PETP films foamed with supercritical CO2 at a suitably high pressure and subsequently annealed for stabilization. The cellular foam structure was further optimized by means of well controlled biaxial stretching in a commercial stretcher and sometimes subsequent inflamation in a pressure chamber. Bipolar electric charging of the internal voids was achieved through the application of high electric fields in an SF0 atmosphere. The new optimized PETP ferroelectric exhibit quite large piezoelectric coefficients up to almost 500 pCN(-1), for which unusually low elastic stiffness of only around 0.3 MPa are essential. The PETP foam ferroelectrics posses unclamped thickenss-extension resonance frequences between approximately 120 and 250 kHz, and are thus highly suitable for several established as well as novel ultrasonic-transductant applications.
In recent communications from these laboratories, we observed that amine-rich thin organic layers are very efficient surfaces for the adhesion of mammalian cells. We prepare such deposits by plasma polymerization at low pressure, atmospheric pressure, or by vacuum-ultraviolet photo-polymerization. More recently, we have also investigated a commercially available material, Parylene diX AM. In this article we first briefly introduce literature relating to electrostatic interactions between cells, proteins, and charged surfaces. We then present certain selected cell-response results that pertain to applications in orthopedic and cardiovascular medicine: we discuss the influence of surface properties on the observed behaviors of two particular cell lines, human U937 monocytes, and Chinese hamster ovary cells. Particular emphasis is placed on possible electrostatic attractive forces due to positively charged R-NH3+ groups and negatively charged proteins and cells, respectively. Experiments carried out with electrets, polymers with high positive or negative surface potentials are added for comparison.
When exposed to sufficiently high electric fields, polymer-foam electret materials with closed cells exhibit ferroelectric-like behavior and may therefore be called ferroelectrets. In cellular ferroelectrets, the influence of the cell size and shape distributions on the application-relevant properties is not yet understood. Therefore, controlled inflation experiments were carried out on cellular polypropylene films, and the resulting elastical and electromechanical parameters were determined. The elastic modulus in the thickness direction shows a minimum with a corresponding maximum in the electromechanical transducer coefficient. The resonance frequency shifts as a function of the elastic modulus and the relative density of the inflated cellular films. Therefore, the transducer properties of cellular ferroelectrets can be optimized by means of controlled inflation. (C) 2004 American Institute of Physics
In cellular, electromechanically active polymer films, the so-called ferroelectrets, the cell size and shape distributions can be varied through a controlled inflation process. Up to now, high-pressure treatments were usually performed at elevated temperatures. There are, however, significant experimental limitations and complications if the pressure and temperature treatments are performed at the same time. Here, we demonstrate the controlled inflation of cellular polypropylene films by means of sepal-ate pressure and temperature treatments. Separate procedures are Much easier to implement. Excellent electromechanical properties were achieved with Such a two-step inflation process. The technique has significant potential for inflating large-area transducer films for electromechanical and electroacoustical applications
Elastic properties and electromechanical coupling factor of inflated polypropylene ferroelectrets
(2006)
Polyvinylidene fluoride was dissolved together with solid sodium hydroxide as catalyst in a dimethylsulfoxide/ acetone mixture and moderately dehydrofluorinated. The dehydrofluorination leads to a partial degradation of the fluorohydrocarbons, and in particular to main-chain scission and to formation of carbon double or triple bonds. This enhances the absorption at UV-vis frequencies. The degradation process also generates a large amount of excess charges in the polymer, which influence the electrical polarization behavior of the dehydrofluorinated polymer. Uniaxial stretching of moderately dehydrofluorinated polyvinylidene fluoride leads to films in a polar phase. Dipole polarization in the degraded and stretched films is demonstrated by means of switching experiments
Piezo-, pyro- and ferroelectricity in poly (vinylidene fluoride-hexafluoropropylene) copolymer films
(2004)
Thin films of poly(vinylidene fluoride-hexafluoropropylene) P(VDF-HFP) show significant electroactive properties, such as piezoelectricity, pyroelectricity and electrostriction. Suitable polar P(VDF-HFP) copolymer films can be prepared by melt-pressing or solution-casting. Dipolar orientation causes the macroscopic polarization and thus also the symmetry breaking necessary for electroactive properties. We discuss the polarization build-up in thin, stretched and non-stretched, films of P(VDF-HFP) copolymer with a HFP content of 15%. Poling currents measured in-situ during electric poling are analyzed and the polarization is calculated. Suitable electric poling leads to hysteresis phenomena of the polarization as a function of the electric field as well as to significant polarization during switching experiments. Our results indicate dipolar orientation also in non-stretched P(VDF-HFP) films
In this paper, a measuring technique is presented for the detection of radial oscillations of tube walls excited by changes in internal air pressure. On organ pipes, the oscillations were investigated by means of piezoelectric polymer films slightly tensioned around the pipe bodies. Employing sensors with patterned electrodes, the well-known elliptical oscillation of the cross section as well as an additional monopole breathing of the organ-pipe body were detected. For the monopole breathing, a close relationship between the pressure distribution of the air-column resonances inside the pipe and the circumference variations along the pipe was observed
Piezoelectric cellular polypropylene films, so-called ferroelectrets, are assembled in a stack with two active transducer layers. The stack is characterized with respect to its linear and quadratic response in a frequency range from 1 kHz to 80 kHz. A relatively smooth frequency response in the sound-pressure level is found for the individual layers as well as for both layers driven in phase. The piezoelectric response of the two-layer stack is twice the response of an individual layer over a rather broad frequency range. Furthermore, the influence of the preparation conditions on the resonance frequency and the effect of the quadratic distortion on the radiated sound are investigated both for the individual transducer films in the stack and for the stack system as a whole
Voided space-charge electrets : piezoelectric transducer materials for electro-acoustic applications
(2004)
Due to their electrically polarized air-filled internal pores, optimized ferroelectrets exhibit a remarkable piezoelectric response, making them suitable for energy harvesting. Expanded polytetrafluoroethylene (ePTFE) ferroelectret films are laminated with two fluorinated-ethylene-propylene (FEP) copolymer films and internally polarized by corona discharge. Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)-coated spandex fabric is employed for the electrodes to assemble an all-organic ferroelectret nanogenerator (FENG). The outer electret-plus-electrode double layers form active device layers with deformable electric dipoles that strongly contribute to the overall piezoelectric response in the proposed concept of wearable nanogenerators. Thus, the FENG with spandex electrodes generates a short-circuit current which is twice as high as that with aluminum electrodes. The stacking sequence spandex/FEP/ePTFE/FEP/ePTFE/FEP/spandex with an average pore size of 3 mu m in the ePTFE films yields the best overall performance, which is also demonstrated by the displacement-versus-electric-field loop results. The all-organic FENGs are stable up to 90 degrees C and still perform well 9 months after being polarized. An optimized FENG makes three light emitting diodes (LEDs) blink twice with the energy generated during a single footstep. The new all-organic FENG can thus continuously power wearable electronic devices and is easily integrated, for example, with clothing, other textiles, or shoe insoles.
Bipolar electrets from polypropylene (PP) are essential, e.g., in electret air filters and in cellular-foam ferroelectrets. Therefore, the mechanism of surface-charge stability enhancement on PP electrets via orthophosphoric-acid surface treatment is investigated in detail. It is shown that the significant charge-stability enhancement can be mainly attributed to deeper surface traps originating from deposited chemicals and topographic features on the modified surfaces. Thermally stimulated discharge of chemically treated and non-treated PP films with different surface-charge densities is used to test the limits of the newly formed deep traps in terms of the capacity for hosting surface charges. When the initial surface-charge density is very high, more charges are forced into shallower original traps on the surface or in the bulk of the treated PP samples, reducing the effect of the deeper surface traps brought by the surface modification. The well-known crossover phenomenon (of the surface-charge decay curves) has been observed between modified PP electrets charged to +/- 2kV and to +/- 3kV. Acoustically probed charge distributions in the thickness direction of PP electrets at different stages of thermal discharging indicate that the deep surface trapping sites may have preference for negative charges, resulting in the observed asymmetric charge stability of the modified PP films.
A double-layer transcrystalline polypropylene (PP) film with a flat central interface layer between its two transcrystalline layers is obtained by recrystallization from the melt between two polytetrafluoroethylene (PTFE) surfaces on both sides of the PP film. Its electret properties are studied and compared with those of a single-layer transcrystalline PP film re-crystallized in contact with only one PTFE surface. Within experimental uncertainty, the two types of transcrystalline films exhibit the same thermal properties and crystallinities. After thermal poling, however, two hetero-charge layers of opposite polarity are found on the internal interfaces of the double-layer transcrystalline films and may together be considered as micrometer-sized dipoles. The unexpected phenomenon does not occur in single-layer transcrystalline samples without a central interface layer, suggesting that the interfaces between the transcrystalline layers and the micrometer-thick central interface layer may be the origin of deeper traps rather than the crystalline structures in the transcrystallites or the spherulites. The origin of the interfacial charges was also studied by means of an injection-blocking charging method, which revealed that intrinsic charge carriers introduced during recrystallization are most likely responsible for the interfacial charges. It is fascinating that a material as familiar as PP can exhibit such intriguing properties with a special bipolar space-charge polarization across the central interface layer after quasi-epitaxial surface moulding into a double-layer transcrystalline form. In addition to applications in electret (micro-)devices for electro-mechanical transduction, the highly ordered structures may also be employed as a new paradigm for studying charge storage and transport in polymer electrets and in dielectrics for DC electrical insulation.
The low surface-charge stability of polypropylene (PP) frequently limits its application as an electret material. In this paper, we demonstrate how the treatment of PP-film surfaces with orthophosphoric acid (H3PO4) enhances their charge stability. To discriminate between the effects of chemical modification and thermal treatment, as-received and annealed PP films are used as reference samples. The electret properties of treated and non-treated PP films are characterized with thermally stimulated discharge (TSD) and isothermal surface-potential decay (ISPD) experiments, from which considerable improvement in thermal and temporal charge stability is observed for samples modified with H3PO4. The half-value temperature (T-1/2) observed on TSD curves of chemically treated PP increases to 131 and 145 degrees C for positive and negative charges, respectively. The enhancement might be attributed to the phosphoric compounds detected on the H3PO4-modified surfaces via attenuated-total-reflection infrared spectroscopy. Deeper surface traps formed at the "foreign" phosphorus-containing structures are able to capture the charges over longer time periods and at higher temperatures, thus leading to significant improvements in the temporal and thermal surface-charge stabilities of PP electrets. Published by AIP Publishing.
Spherulite-related space-charge electret properties of polypropylene (PP) have been widely discussed in the past decades. In the present paper, a less-common crystalline structure in PP-transcrystalline PP-is studied regarding its electret behavior in comparison with the typical spherulitic morphology. Polarized light microscopy and differential scanning calorimetry were employed to characterize the crystallite types and crystallinities of transcrystalline and spherulitic PP. Their electret functionality is investigated by means of thermally stimulated discharge experiments, where the cross-over phenomenon is observed on transcrystalline PP films, whereas surface-potential saturation and undercharging on the surface occur on the spherulitic samples. Besides, an asymmetrical behavior of positive and negative surface-charge stabilities is found on PP with spherulites, the negatively charged spherulitic surfaces show a better charge stability. It is shown that PP electrets are very sensitive to changes in the microscopic crystalline structures and their interfaces as well as in the molecular conformations controlled through adjustments of the respective processing steps. In addition, surface and bulk nanocomposites of PP or low-density polyethylene with inorganic particles are included in the comparison. In view of recent developments in the areas of PP-based electret-fiber filters and cellular-foam ferroelectrets, the observed changes in the charge-storage properties may have particular relevance, as the required film, fiber, or foam processing might significantly modify crystalline morphologies and nano-scale interfaces in PP electrets. Limitations in the charge-storage capabilities of interface structures may also be of interest in the context of high-voltage electrical-insulation materials where reduced space-charge accumulation and slightly increased charge transport can be advantageous.
Tailoring the secondary surface morphology of electro-spun nanofibers has been highly desired, as such delicate structures equip nanofibers with distinct functions. Here, we report a simple strategy to directly reconstruct the surface of polyvinyl alcohol/polyvinylpyrrolidone (PVA/PVP) nanofibers by water evaporation. The roughness and diameter of the nanofibers depend on the temperature during vacuum drying. Surface changes of the nanofibers from smooth to rough were observed at 55 degrees C, with a significant drop in nanofiber diameter. We attribute the formation of the secondary surface morphology to the intermolecular forces in the water vapor, including capillary and the compression forces, on the basis of the results from the Fourier-transform infrared (FTIR) and X-ray photoelectron (XPS) spectroscopy. The strategy is universally effective for various electro-spun polymer nanofibers, thus opening up avenues toward more detailed and sophisticated structure design and implementation for nanofibers.
Thin films of ferroelectric beta-phase poly(vinylidene fluoride) (PVDF) were spin-coated from a solution that contained small amounts of the ionic liquid (IL) 1-ethyl-3-methylimidazolium nitrate. A remanent polarization of 60 mC/m(2) and a quasi-static pyroelectric coefficient of 19 mu C/m(2)K at 30 degrees C were observed in the films. It is suggested that the IL promotes the formation of the beta phase through dipolar interactions between PVDF chain-molecules and the IL. The dipolar interactions are identified as Coulomb attraction between hydrogen atoms in PVDF chains and anions in IL. The strong crystallinity increase is probably caused by the same dipolar interaction as well.
beta-phase poly(vinylidene fluoride-hexafluoropropylene) (P(VDF-HFP)) copolymer films were prepared by uniaxially stretching solution-cast or melt-quenched samples. Different preparation routes lead to different amounts of the crystalline alpha and beta phases in the films, as detected by means of Fourier-transform infrared spectroscopy and X-ray diffractometry. The beta phase is significantly enhanced in melt-quenched and stretched films in comparison to solution-cast and stretched films. This is particularly true for copolymer samples with higher HFP content. The beta- phase enhancement is also observed in ferroelectric-hysteresis experiments where a rather high polarization of 58 mC/ m(2) was found on melt-quenched and stretched samples after poling at electric fields of 140 MV/m. After poling at 160 MV/m, one of these samples exhibited a piezoelectric d(33) coefficient as high as 21 pC/N. An electric-field-induced partial transition from the alpha to the beta phase was also observed on the melt-quenched and stretched samples. This effect leads to a further increase in the applications-relevant dipole polarization. Uniaxially stretched ferroelectric- polymer films are highly anisotropic. Dielectric resonance spectroscopy reveals a strong increase of the transverse piezoelectric d(32) coefficient and a strong decrease of the transverse elastic modulus c(32) upon heating from 20 to 50 degrees C.
We present calculations on the deformation of two- and three-layer electret systems. The electrical field is coupled with the stress-strain equations by means of the Maxwell stress tensor. In the simulations, two-phase systems are considered, and intrinsic relative dielectric permittivity and Young's modulus of the phases are altered. The numerically calculated electro-mechanical activity is compared to an analytical expression. Simulations are performed on two- and three-layer systems. Various parameters in the model are systematically varied and their influence on the resulting piezoelectricity is estimated. In three-layer systems with bipolar charge, the piezoelectric coefficients exhibit a strong dependence on the elastic moduli of the phases. However, with mono-polar charge, there is no significant piezoelectric effect. A two-dimensional simulation illustrated that higher piezoelectric coefficients can be obtained for non-uniform surface charges and low Poisson's ratio of phases. Irregular structures considered exhibit low piezoelectric activity compared to two-layer structures. (C) 2004 Elsevier B.V. All rights reserved
In this paper, a recently developed numerical method to analyze dielectric-spectroscopy data is applied to alpha-phase polyvinylidene fluoride (PVDF). The numerical procedure is non-parametric and does not contain any of the extensively used empirical formulas mentioned in the literature. The method basically recovers the unknown distribution of relaxation times of the generalized dielectric function representation by simultaneous application of the Monte Carlo integration method and of the constrained least-squares optimization. The relaxation map constructed after the numerical analysis is compared to a-phase PVDF data presented in the literature and results of the parametric analysis with a well- known empirical formula. (c) 2005 Elsevier B.V. All rights reserved
The conductivity of alpha-polyvinylidene fluoride is obtained from dielectric measurements performed in the frequency domain at several temperatures. At temperatures above the glass-transition, the conductivity can be interpreted as an ionic conductivity, which confirms earlier results reported in the literature. Our investigation shows that the observed ionic conductivity is closely related to the amorphous phase of the polymer. (C) 2005 American Institute of Physics
Laminated polymer-film systems with well-defined void structures were prepared from fluoroethylenepropylene (FEP) and polytetrafluoroethylene (PTFE) layers. First the PTFE films were patterned and then fusion-bonded with the FEP films. The laminates were subjected to either corona or contact charging in order to obtain the desired piezoelectricity. The build-up of the "macro-dipoles" in the laminated films was studied by recording the electric hysteresis loops. The resulting electro-mechanical properties were investigated by means of dielectric resonance spectroscopy (DRS) and direct measurements of the stress-strain relationship. Moreover, the thermal stability of the piezoelectric d (33) coefficient was investigated at elevated temperatures and via thermally stimulated discharge (TSD) current measurements in short circuit. For 150 mu m thick laminated films, consisting of one 25 mu m thick PTFE layer, two 12.5 mu m thick FEP layers, and a void of 100 mu m height, the critical voltage necessary for the build-up of the "macro-dipoles" in the inner voids was approximately 1400 V, which agrees with the value calculated from the Paschen Law. A quasi-static piezoelectric d (33) coefficient up to 300 pC/N was observed after corona charging. The mechanical properties of the film systems are highly anisotropic. At room temperature, the Young's moduli of the laminated film system are around 0.37 MPa in the thickness direction and 274 MPa in the lateral direction, respectively. Using these values, the theoretical shape anisotropy ratio of the void was calculated, which agrees well with experimental observation. Compared with films that do not exhibit structural regularity, the laminates showed improved thermal stability of the d (33) coefficients. The thermal stability of d (33) can be further improved by pre-aging. E.g., the reduction of the d (33) value in the sample pre-aged at 150A degrees C for 5 h was less than 5% after annealing for 30 h at a temperature of 90A degrees C.
In our fast-changing world, human-machine interfaces (HMIs) are of ever-increasing importance. Among the most ubiquitous examples are touchscreens that most people are familiar with from their smartphones. The quality of such an HMI can be improved by adding haptic feedback-an imitation of using mechanical buttons-to the touchscreen. Thin-film actuators on the basis of electro-mechanically active polymers (EAPs), with the electroactive material sandwiched between two compliant electrodes, offer a promising technology for haptic surfaces. In thin-film technology, the thickness and the number of stacked layers of the electroactive dielectric are key parameters for tuning a system. Therefore, we have experimentally investigated the influence of the thickness of a single EAP layer on the electrical and the electro-mechanical performance of the transducer. In order to achieve high electro-mechanical actuator outputs, we have employed relaxor-ferroelectric ter-fluoropolymers that can be screen-printed. By means of a model-based approach, we have also directly compared single- and multi-layer actuators, thus providing guidelines for optimized transducer configurations with respect to the system requirements of haptic applications for which the operation frequency is of particular importance.
A new variant of the Laser-Induced Pressure-Pulse (LIPP) method for repeatable, time-resolved space-charge profile measurements is proposed and demonstrated. Automated deposition of a fresh laser-target film before each illumination leads to good repeatability of the LIPP and thus allows for the detection of time-resolved changes in the space-charge distribution over many hours. We describe and discuss the experimental setup and its features, compare the repeatability of the LIPP measurements on the same sample without and with re-preparation of the test cell, and present the time-resolved evolution of the space-charge profile in a two-layer arrangement of a silicone-grease and a silicone-elastomer film as an example. Finally, the temperature dependence of the space-charge evolution during polarization under high voltage and during depolarization in short circuit is shown. Possible uses and future developments of the new LIPP approach are also discussed.
We report a process for preparing polymer ferroelectrets by means of screen printing-a technology that is widely used for the two-dimensional patterning of printed layers. In order to produce polymer-film systems with cavities that are suitable for bipolar electric charging, a screen-printing paste is deposited through a screen with a pre-designed pattern onto the surface of a polymer electret film. Another such polymer film is placed on top of the printed pattern, and well-defined cavities are formed in-between. During heating and curing, the polymer films are tightly bonded to the patterned paste layer so that a stable three-layer system is obtained. In the present work, polycarbonate (PC) films have been employed as electret layers. Screen printing, curing and charging led to PC ferroelectret systems with a piezoelectric d (33) coefficient of about 28 pC/N that is stable up to 100 C-a similar to. Due to the rather soft patterned layer, d (33) strongly decreases already for static pressures of tens of kPa. The results demonstrate the suitability of screen printing for the preparation of ferroelectret systems.
New ferroelectrets were developed on the basis of foams from cyclo-olefin polymers and copolymers. The results obtained on the cyclo-olefin polymer foam demonstrate a significant improvement of the service temperature for ferroelectret transducer materials. Suitable compounding and preparation led to cyclo-olefin ferroelectrets with an electromechanical activity of around 15 pC/N, which is thermally stable at least up to 110 degrees C. The properties in sensor and actuator applications are strongly dependent on the processing parameters related to film-making, sensor and actuator preparation, gas content and electric charging. The processing window for the film stretching was very narrow compared to the earlier developed polypropylene ferroelectrets. The film porosity, softness and thus the electromechanical activity are adjusted by gas-diffusion expansion. The activity of the electromechanically operating sensors and actuators was increased by stacking several layers of cellular cyclo-olefin film. For applications such as flat loudspeakers, the foamed films are tuned by tensioning them on a support frame. Correct tensioning was essential also for reducing the distortion levels.
Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor in a molecular-layer deposition process. As a result of the surface treatment, significant improvements of the thermal and temporal charge stability were observed. Charge-decay measurements revealed enhancements of the half-value temperatures and the relaxation times of positively charged FEP electrets by at least 120 A degrees C and two orders of magnitude, respectively. Beyond previous publications on fluoropolymer electrets with surface modification, we here report enhanced charge stabilities of the FEP films charged in negative as well as in positive corona discharges. Even though the improvement for negatively charged FEP films is moderate (half-value temperature about 20 A degrees C higher), our experiments show that the asymmetry in positive and negative charge stability that is typical for FEP electrets can be overcome by means of chemical surface treatments. The results are discussed in the context of the formation of modified surface layers with enhanced charge-trapping properties.
Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor by means of molecular-layer deposition. The treatment leads to considerable improvements of the electret-charge stability on positively charged films. A slight improvement is also observed for negatively charged films. In line with our previous findings, we attribute the improvement in electret properties to the formation of deeper traps on the chemically modified polymer surfaces. Here, we investigate the influence of the charge density on electret stability of FEP films with modified surfaces. Trap-energy spectra obtained from thermally-stimulated-discharge measurements indicate that the charge stability on modified FEP films depends on how the surface traps are populated and on the availability of additional deeper traps.
Enhanced electret charge stability on Polyethylene Films treated with Titanium-Tetrachloride vapor
(2012)
Low-density polyethylene (LDPE) films have been treated with titanium-tetrachloride vapor by means of the molecular-layer-deposition method. It is shown that such a treatment leads to a considerable improvement of the electret properties for both positively and negatively charged films. The temperature stability of the electret homo-charge has been increased by approximately 60 degrees C. At the same time, the temporal stability of charge is also considerably improved. Modified low-density polyethylene films show no "cross-over phenomenon" when charged to higher voltages. Thus, it is now possible to produce electrets from polyethylene films with high initial charge densities, but without a strongly reduced charge stability. The influence of a chemical treatment with titanium-tetrachloride vapor on charge injection from aluminum electrodes into polyethylene films was also investigated. It is found that the interface between an aluminum electrode and a modified LDPE surface layer has different injection properties for positive and negative charges. Electrons can be injected across the modified interface, whereas injection of holes is either very limited or non-existent.
The surface of polytetrafluoroethylene films was treated with titanium-tetrachloride vapor. The treatment was carried out in a flow reactor by means of molecular-layer deposition, a method from the arsenal of chemical nanotechnology. X-ray photoelectron spectroscopy reveals that such a treatment results in considerable changes in the chemical composition at and near the surface of the fluoropolymer film. Both, defluorination and oxidation of the surface were observed. At the same time, samples treated with titanium tetrachloride show a significant enhancement in the thermal stability of the positive homocharge. The thermally stimulated surface-potential-decay curves were observed to shift to higher temperatures by more than 100 degrees C.
Ferroelectrets have been fabricated from low-density polyethylene (LDPE) films by means of a template-based lamination. The temperature dependence of the piezoelectric d(33) coefficient has been investigated. It was found that low-density polyethylene ferroelectrets have rather low thermal stability with the piezoelectric coefficient decaying almost to zero already at 100 degrees C. This behavior is attributed to the poor electret properties of the polyethylene films used for the fabrication of the ferroelectrets. In order to improve the charge trapping and the thermal stability of electret charge and piezoelectricity, LDPE ferroelectrets were treated with orthophosphoric acid. The treatment resulted in considerable improvements of the charge stability in LDPE films and in ferroelectret systems made from them. For example, the charge and piezoelectric-coefficient decay curves shifted to higher temperatures by 60 K and 40 K, respectively. It is shown that the decay of the piezoelectric coefficient in LDPE ferroelectrets is governed by the relaxation of less stable positive charges. The treatment also leads to noticeable changes in the chemical composition of the LDPE surface. Infrared spectroscopy reveals absorption bands attributed to phosphorus-containing structures, while scanning electron microscopy shows new island-like structures, 50-200 nm in diameter, on the modified surface.
The zeta potential of the motile spores of the green alga (seaweed) Ulva linza was quantified by video microscopy in combination with optical tweezers and determined to be -19.3ñ1.1 mV. The electrostatic component involved in the settlement and adhesion of spores was studied using electret surfaces consisting of PTFE and bearing different net charges. As the surface chemistry remains the same for differently charged surfaces, the experimental results isolate the influence of surface charge and thus electrostatic interactions. Ulva spores were demonstrated to have a reduced tendency to settle on negatively charged surfaces and when they did settle the adhesion strength of settled spores was lower than with neutral or positively charged surfaces. These observations can be ascribed to electrostatic interactions.