530 Physik
Refine
Year of publication
- 2015 (20) (remove)
Document Type
- Doctoral Thesis (20) (remove)
Is part of the Bibliography
- yes (20)
Keywords
Institute
Semi-empirical sea-level models (SEMs) exploit physically motivated empirical relationships between global sea level and certain drivers, in the following global mean temperature. This model class evolved as a supplement to process-based models (Rahmstorf (2007)) which were unable to fully represent all relevant processes. They thus failed to capture past sea-level change (Rahmstorf et al. (2012)) and were thought likely to underestimate future sea-level rise. Semi-empirical models were found to be a fast and useful tool for exploring the uncertainties in future sea-level rise, consistently giving significantly higher projections than process-based models.
In the following different aspects of semi-empirical sea-level modelling have been studied. Models were first validated using various data sets of global sea level and temperature. SEMs were then used on the glacier contribution to sea level, and to infer past global temperature from sea-level data via inverse modelling. Periods studied encompass the instrumental period, covered by tide gauges (starting 1700 CE (Common Era) in Amsterdam) and satellites (first launched in 1992 CE), the era from 1000 BCE (before CE) to present, and the full length of the Holocene (using proxy data). Accordingly different data, model formulations and implementations have been used. It could be shown in Bittermann et al. (2013) that SEMs correctly predict 20th century sea-level when calibrated with data until 1900 CE. SEMs also turned out to give better predictions than the Intergovernmental Panel on Climate Change (IPCC) 4th assessment report (AR4, IPCC (2007)) models, for the period from 1961–2003 CE.
With the first multi-proxy reconstruction of global sea-level as input, estimate of the human-induced component of modern sea-level change and projections of future sea-level rise were calculated (Kopp et al. (2016)). It turned out with 90% confidence that more than 40 % of the observed 20th century sea-level rise is indeed anthropogenic. With the new semi-empirical and IPCC (2013) 5th assessment report (AR5) projections the gap between SEM and process-based model projections closes, giving higher credibility to both. Combining all scenarios, from strong mitigation to business as usual, a global sea-level rise of 28–131 cm relative to 2000 CE, is projected with 90% confidence. The decision for a low carbon pathway could halve the expected global sea-level rise by 2100 CE.
Present day temperature and thus sea level are driven by the globally acting greenhouse-gas forcing. Unlike that, the Milankovich forcing, acting on Holocene timescales, results mainly in a northern-hemisphere temperature change. Therefore a semi-empirical model can be driven with northernhemisphere temperatures, which makes it possible to model the main subcomponent of sea-level change over this period. It showed that an additional positive constant rate of the order of the estimated Antarctic sea-level contribution is then required to explain the sea-level evolution over the Holocene. Thus the global sea level, following the climatic optimum, can be interpreted as the sum of a temperature induced sea-level drop and a positive long-term contribution, likely an ongoing response to deglaciation coming from Antarctica.
The main goal of this cumulative thesis is the derivation of surface emissivity data in the infrared from radiance measurements of Venus. Since these data are diagnostic of the chemical composition and grain size of the surface material, they can help to improve knowledge of the planet’s geology. Spectrally resolved images of nightside emissions in the range 1.0-5.1 μm were recently acquired by the InfraRed Mapping channel of the Visible and InfraRed Thermal Imaging Spectrometer (VIRTIS-M-IR) aboard ESA’s Venus EXpress (VEX). Surface and deep atmospheric thermal emissions in this spectral range are strongly obscured by the extremely opaque atmosphere, but three narrow spectral windows at 1.02, 1.10, and 1.18 μm allow the sounding of the surface. Additional windows between 1.3 and 2.6 μm provide information on atmospheric parameters that is required to interpret the surface signals. Quantitative data on surface and atmosphere can be retrieved from the measured spectra by comparing them to simulated spectra. A numerical radiative transfer model is used in this work to simulate the observable radiation as a function of atmospheric, surface, and instrumental parameters. It is a line-by-line model taking into account thermal emissions by surface and atmosphere as well as absorption and multiple scattering by gases and clouds. The VIRTIS-M-IR measurements are first preprocessed to obtain an optimal data basis for the subsequent steps. In this process, a detailed detector responsivity analysis enables the optimization of the data consistency. The measurement data have a relatively low spectral information content, and different parameter vectors can describe the same measured spectrum equally well. A usual method to regularize the retrieval of the wanted parameters from a measured spectrum is to take into account a priori mean values and standard deviations of the parameters to be retrieved. This decreases the probability to obtain unreasonable parameter values. The multi-spectrum retrieval algorithm MSR is developed to additionally consider physically realistic spatial and temporal a priori correlations between retrieval parameters describing different measurements. Neglecting geologic activity, MSR also allows the retrieval of an emissivity map as a parameter vector that is common to several spectrally resolved images that cover the same surface target. Even applying MSR, it is difficult to obtain reliable emissivity maps in absolute values. A detailed retrieval error analysis based on synthetic spectra reveals that this is mainly due to interferences from parameters that cannot be derived from the spectra themselves, but that have to be set to assumed values to enable the radiative transfer simulations. The MSR retrieval of emissivity maps relative to a fixed emissivity is shown to effectively avoid most emissivity retrieval errors. Relative emissivity maps at 1.02, 1.10, and 1.18 μm are finally derived from many VIRTIS-M-IR measurements that cover a surface target at Themis Regio. They are interpreted as spatial variations relative to an assumed emissivity mean of the target. It is verified that the maps are largely independent of the choice of many interfering parameters as well as the utilized measurement data set. These are the first Venus IR emissivity data maps based on a consistent application of a full radiative transfer simulation and a retrieval algorithm that respects a priori information. The maps are sufficiently reliable for future geologic interpretations.
Organic bulk heterojunction (BHJ) solar cells based on polymer:fullerene blends are a promising alternative for a low-cost solar energy conversion. Despite significant improvements of the power conversion efficiency in recent years, the fundamental working principles of these devices are yet not fully understood. In general, the current output of organic solar cells is determined by the generation of free charge carriers upon light absorption and their transport to the electrodes in competition to the loss of charge carriers due to recombination.
The object of this thesis is to provide a comprehensive understanding of the dynamic processes and physical parameters determining the performance. A new approach for analyzing the characteristic current-voltage output was developed comprising the experimental determination of the efficiencies of charge carrier generation, recombination and transport, combined with numerical device simulations.
Central issues at the beginning of this work were the influence of an electric field on the free carrier generation process and the contribution of generation, recombination and transport to the current-voltage characteristics. An elegant way to directly measure the field dependence of the free carrier generation is the Time Delayed Collection Field (TDCF) method. In TDCF charge carriers are generated by a short laser pulse and subsequently extracted by a defined rectangular voltage pulse. A new setup was established with an improved time resolution compared to former reports in literature. It was found that charge generation is in general independent of the electric field, in contrast to the current view in literature and opposed to the expectations of the Braun-Onsager model that was commonly used to describe the charge generation process. Even in cases where the charge generation was found to be field-dependend, numerical modelling showed that this field-dependence is in general not capable to account for the voltage dependence of the photocurrent. This highlights the importance of efficient charge extraction in competition to non-geminate recombination, which is the second objective of the thesis.
Therefore, two different techniques were combined to characterize the dynamics and efficiency of non-geminate recombination under device-relevant conditions. One new approach is to perform TDCF measurements with increasing delay between generation and extraction of charges. Thus, TDCF was used for the first time to measure charge carrier generation, recombination and transport with the same experimental setup. This excludes experimental errors due to different measurement and preparation conditions and demonstrates the strength of this technique. An analytic model for the description of TDCF transients was developed and revealed the experimental conditions for which reliable results can be obtained. In particular, it turned out that the $RC$ time of the setup which is mainly given by the sample geometry has a significant influence on the shape of the transients which has to be considered for correct data analysis.
Secondly, a complementary method was applied to characterize charge carrier recombination under steady state bias and illumination, i.e. under realistic operating conditions. This approach relies on the precise determination of the steady state carrier densities established in the active layer. It turned out that current techniques were not sufficient to measure carrier densities with the necessary accuracy. Therefore, a new technique {Bias Assisted Charge Extraction} (BACE) was developed. Here, the charge carriers photogenerated under steady state illumination are extracted by applying a high reverse bias. The accelerated extraction compared to conventional charge extraction minimizes losses through non-geminate recombination and trapping during extraction. By performing numerical device simulations under steady state, conditions were established under which quantitative information on the dynamics can be retrieved from BACE measurements.
The applied experimental techniques allowed to sensitively analyse and quantify geminate and non-geminate recombination losses along with charge transport in organic solar cells. A full analysis was exemplarily demonstrated for two prominent polymer-fullerene blends.
The model system P3HT:PCBM spincast from chloroform (as prepared) exhibits poor power conversion efficiencies (PCE) on the order of 0.5%, mainly caused by low fill factors (FF) and currents. It could be shown that the performance of these devices is limited by the hole transport and large bimolecular recombination (BMR) losses, while geminate recombination losses are insignificant. The low polymer crystallinity and poor interconnection between the polymer and fullerene domains leads to a hole mobility of the order of 10^-7 cm^2/Vs which is several orders of magnitude lower than the electron mobility in these devices. The concomitant build up of space charge hinders extraction of both electrons and holes and promotes bimolecular recombination losses.
Thermal annealing of P3HT:PCBM blends directly after spin coating improves crystallinity and interconnection of the polymer and the fullerene phase and results in comparatively high electron and hole mobilities in the order of 10^-3 cm^2/Vs and 10^-4 cm^2/Vs, respectively. In addition, a coarsening of the domain sizes leads to a reduction of the BMR by one order of magnitude. High charge carrier mobilities and low recombination losses result in comparatively high FF (>65%) and short circuit current (J_SC ≈ 10 mA/cm^2). The overall device performance (PCE ≈ 4%) is only limited by a rather low spectral overlap of absorption and solar emission and a small V_OC, given by the energetics of the P3HT.
From this point of view the combination of the low bandgap polymer PTB7 with PCBM is a promising approach. In BHJ solar cells, this polymer leads to a higher V_OC due to optimized energetics with PCBM. However, the J_SC in these (unoptimized) devices is similar to the J_SC in the optimized blend with P3HT and the FF is rather low (≈ 50%). It turned out that the unoptimized PTB7:PCBM blends suffer from high BMR, a low electron mobility of the order of 10^-5 cm^2/Vs and geminate recombination losses due to field dependent charge carrier generation.
The use of the solvent additive DIO optimizes the blend morphology, mainly by suppressing the formation of very large fullerene domains and by forming a more uniform structure of well interconnected donor and acceptor domains of the order of a few nanometers. Our analysis shows that this results in an increase of the electron mobility by about one order of magnitude (3 x 10^-4 cm^2/Vs), while BMR and geminate recombination losses are significantly reduced. In total these effects improve the J_SC (≈ 17 mA/cm^2) and the FF (> 70%). In 2012 this polymer/fullerene combination resulted in a record PCE for a single junction OSC of 9.2%.
Remarkably, the numerical device simulations revealed that the specific shape of the J-V characteristics depends very sensitively to the variation of not only one, but all dynamic parameters. On the one hand this proves that the experimentally determined parameters, if leading to a good match between simulated and measured J-V curves, are realistic and reliable. On the other hand it also emphasizes the importance to consider all involved dynamic quantities, namely charge carrier generation, geminate and non-geminate recombination as well as electron and hole mobilities. The measurement or investigation of only a subset of these parameters as frequently found in literature will lead to an incomplete picture and possibly to misleading conclusions.
Importantly, the comparison of the numerical device simulation employing the measured parameters and the experimental $J-V$ characteristics allows to identify loss channels and limitations of OSC. For example, it turned out that inefficient extraction of charge carriers is a criticical limitation factor that is often disobeyed. However, efficient and fast transport of charges becomes more and more important with the development of new low bandgap materials with very high internal quantum efficiencies. Likewise, due to moderate charge carrier mobilities, the active layer thicknesses of current high-performance devices are usually limited to around 100 nm. However, larger layer thicknesses would be more favourable with respect to higher current output and robustness of production. Newly designed donor materials should therefore at best show a high tendency to form crystalline structures, as observed in P3HT, combined with the optimized energetics and quantum efficiency of, for example, PTB7.
In this thesis, I study ultrafast dynamics in perovskite oxides using time resolved broadband spectroscopy. I focus on the observation of coherent phonon propagation by time resolved Brillouin scattering: following the excition of metal transducer films with a femtosecond infrared pump pulse, coherent phonon dynamics in the GHz frequency range are triggered. Their propagation is monitored using a delayed white light probe pulse. The technique is illustrated on various thin films and multilayered samples. I apply the technique to investigate the linear and nonlinear acoustic response in bulk SrTiO_3, which displays a ferroelastic phase transition from a cubic to a tetragonal structural phase at T_a=105 K. In the linear regime, I observe a coupling of the observed acoustic phonon mode to the softening optic modes describing the phase transition. In the nonlinear regime, I find a giant slowing down of the sound velocity in the low temperature phase that is only observable for a strain amplitude exceeding the tetragonality of the material. It is attributed to a coupling of the high frequency phonons to ferroelastic domain walls in the material. I propose a new mechanism for the coupling of strain waves to the domain walls that is only effective for high amplitude strain. A detailed study of the phonon attenuation across a wide temperature range shows that the phonon attenuation at low temperatures is influenced by the domain configuration, which is determined by interface strain. Preliminary measurements on magnetic-ferroelectric multilayers reveal that the excitation fluence needs to be carefully controlled when dynamics at phase transitions are studied.