Refine
Document Type
- Article (1)
- Doctoral Thesis (1)
Language
- English (2) (remove)
Is part of the Bibliography
- yes (2)
Keywords
- PEDOT (2) (remove)
Institute
- Institut für Physik und Astronomie (2) (remove)
Doped spiro-OMeTAD at present is the most commonly used hole transport material (HTM) in n-i-p-type perovskite solar cells, enabling high efficiencies around 22%. However, the required dopants were shown to induce nonradiative recombination of charge carriers and foster degradation of the solar cell. Here, in a novel approach, highly conductive and inexpensive water-free poly(3,4-ethylenedioxythiophene) (PEDOT) is used to replace these dopants. The resulting spiro-OMeTAD/PEDOT (SpiDOT) mixed films achieve higher lateral conductivities than layers of doped spiro-OMeTAD. Furthermore, combined transient and steady-state photoluminescence studies reveal a passivating effect of PEDOT, suppressing nonradiative recombination losses at the perovskite/HTM interface. This enables excellent quasi-Fermi level splitting values of up to 1.24 eV in perovskite/SpiDOT layer stacks and high open-circuit voltages (V-OC) up to 1.19 V in complete solar cells. Increasing the amount of dopant-free spiro-OMeTAD in SpiDOT layers is shown to enhance hole extraction and thereby improves the fill factor in solar cells. As a consequence, stabilized efficiencies up to 18.7% are realized, exceeding cells with doped spiro-OMeTAD as a HTM in this study. Moreover, to the best of our knowledge, these results mark the lowest nonradiative recombination loss in the V-OC (140 mV with respect to the Shockley-Queisser limit) and highest efficiency reported so far for perovskite solar cells using PEDOT as a HTM.
It is known that the efficiency of organic light-emitting devices (OLEDs) is strongly influenced by the ’quality′ of the thin films [1]. On the basis of this conviction, the work presented in this thesis aimed to obtain a better understanding of the structure of organic thin films of general interest in the field of organic light emitting devices by using scanning probe microscopies (SPMs). A not yet reported crystal structure of quaterthiophene film grown on potassium hydrogen (KHP) is determined by optical measurements, a simulation program, diffraction at both normal incidence and grazing angle and AFM. The crystal cell is triclinic with parameters a = 0.721 nm, b = 0.632 nm, c = 0.956 nm and a = 91°, b = 91.4°, g = 91° [2]. The morphologies of four organic thin films deposited on gold are characterized by ultra high vacuum scanning tunneling microscopy (UHV-STM). Terraces in an hexanethiol monolayer, lamellar structures in an azobenzenethiol monolayer, rods in a a poly(paraphenylenevinylene) oligomer film and a granular morphology in an oxadiazole film are shown. The topographies of a series of poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT/PSS) films deposited on indium-tin oxide (ITO) and gold obtained from dispersions with PEDOT:PSS weight ratios of 1:20, 1:6 and 1:1 are investigated by AFM. It is demonstrated that the films show the same topography on gold and on ITO. It is shown that the PEDOT films eliminate the spike features of ITO. It is reported that PEDOT 1:20 and 1:6 appear indistinguishable between each other but different from PEDOT 1:1 (the most conductive). Coupling STM and I-d measurements, a not yet reported structural model of PEDOT 1:1 on gold is obtained [3]. In this model the surface presents grains and the bulk particles/domains rich in PEDOT embedded in a PEDOT-poor matrix. The equation of conductivity is derived. A STM investigation of four PEDOT films deposited on ITO obtained from dispersions with the same PEDOT:PSS weight ratio of 1:1 is carried out [4]. The films differ either for the presence of sorbitol or for a different synthetic route (and they present different conductivities). For the first time a quantitative and qualitative correlation between the nanometer-scale morphology of PEDOT films with and without sorbitol and their conductivity is established.