Refine
Has Fulltext
- yes (15) (remove)
Year of publication
- 2019 (15) (remove)
Document Type
- Doctoral Thesis (15) (remove)
Is part of the Bibliography
- yes (15)
Keywords
- Ammoniak (1)
- Aromaten (1)
- Beschichtung (1)
- Bindung (1)
- Biomasseverwertung (1)
- Block Copolymer (1)
- C-Arlyglykosid (1)
- Ceroxid (1)
- Chalkon (1)
- DFT (1)
Institute
- Institut für Chemie (15) (remove)
In den letzten Jahrzehnten fand auch in der Beschichtungsindustrie ein Umdenken hin zu umweltfreundlicheren Farben und Lacken statt. Allerdings basieren auch neue Lösungen meist nicht auf Biopolymeren und in einem noch geringeren Anteil auf wasserbasierten Beschichtungssystemen aus nachwachsenden Rohstoffen. Dies stellt den Anknüpfungspunkt dieser Arbeit dar, in der untersucht wurde, ob das Biopolymer Stärke das Potenzial zum wasserbasierten Filmbildner für Farben und Lacke besitzt. Dabei müssen angelehnt an etablierte synthetische Marktprodukte die folgenden Kriterien erfüllt werden: Die wässrige Dispersion muss mindestens einen 30%igen Feststoffgehalt haben, bei Raumtemperatur verarbeitet werden können und Viskositäten zwischen 10^2-10^3 mPa·s aufweisen. Die finale Beschichtung muss einen geschlossenen Film bilden und sehr gute Haftfestigkeiten zu einer spezifischen Oberfläche, in dieser Arbeit Glas, besitzen. Als Grundlage für die Modifizierung der Stärke wurde eine Kombination von molekularem Abbau und chemischer Funktionalisierung ausgewählt. Da nicht bekannt war, welchen Einfluss die Stärkeart, die gewählte Abbaureaktion als auch verschiedene Substituenten auf die Dispersionsherstellung und deren Eigenschaften sowie die Beschichtungseigenschaften ausüben könnten, wurden die strukturellen Parameter getrennt voneinander untersucht.
Das erste Themengebiet beinhaltete den oxidativen Abbau von Kartoffel- und Palerbsenstärke mittels des Hypochlorit-Abbaus (OCl-) und des ManOx-Abbaus (H2O2, KMnO4). Mit beiden Abbaureaktionen konnten vergleichbare gewichtsmittlere Molmassen (Mw) von 2·10^5-10^6 g/mol (GPC-MALS) hergestellt werden. Allerdings führten die gewählten Reaktionsbedingungen beim ManOx-Abbau zur Bildung von Gelpartikeln. Diese lagen im µm-Bereich (DLS und Kryo-REM-Messungen) und hatten zur Folge, dass die ManOx-Proben deutlich erhöhte Viskositäten (c: 7,5 %; 9-260 mPa·s) im Vergleich zu den OCl--Proben (4-10 mPa·s) bei scherverdünnendem Verhalten besaßen und die Eigenschaften von viskoelastischen Gelen (G‘ > G‘‘) zeigten. Des Weiteren wiesen sie reduzierte Heißwasserlöslichkeiten (95 °C, vorrangig: 70-99 %) auf. Der OCl--Abbau führte zu hydrophileren (Carboxylgruppengehalt bis zu 6,1 %; ManOx: bis zu 3,1 %), nach 95 °C-Behandlung vollständig wasserlöslichen abgebauten Stärken, die ein Newtonsches Fließverhalten mit Eigenschaften einer viskoelastischen Flüssigkeit (G‘‘ > G‘) hatten. Die OCl--Proben konnten im Vergleich zu den ManOx-Produkten (10-20 %) zu konzentrierteren Dispersionen (20-40 %) verarbeitet werden, die gleichzeitig die Einschränkung von anwendungsrelevanten Mw auf < 7·10^5 g/mol zuließen (Konzentration sollte > 30 % sein). Außerdem führten nur die OCl--Proben der Kartoffelstärke zu transparenten (alle anderen waren opak) geschlossenen Beschichtungsfilmen. Somit hebt sich die Kombination von OCl--Abbau und Kartoffelstärke mit Hinblick auf die Endanwendung ab.
Das zweite Themengebiet umfasste Untersuchungen zum Einfluss von Ester- und Hydroxyalkylether-Substituenten auf Basis einer industriell abgebauten Kartoffelstärke (Mw: 1,2·10^5 g/mol) vor allem auf die Dispersionsherstellung, die rheologischen Eigenschaften der Dispersionen und die Beschichtungseigenschaften in Kombination mit Glassubstraten. Dazu wurden Ester und Ether mit DS/MS-Werten von 0,07-0,91 synthetisiert. Die Derivate konnten zu wasserbasierten Dispersionen mit Konzentrationen von 30-45 % verarbeitet werden, wobei bei hydrophoberen Modifikaten ein Co-Lösemittel, Diethylenglycolmonobutylether (DEGBE), eingesetzt werden musste. Die Feststoffgehalte sanken dabei für beide Derivatklassen vor allem mit zunehmender Alkylkettenlänge. Die anwendungsrelevanten Viskositäten (323-1240 mPa·s) stiegen auf Grund von Wechselwirkungen tendenziell mit DS/MS und Alkylkettenlänge an. Hinsichtlich der Beschichtungseigenschaften erwiesen sich die Ester vergleichend zu den Ethern als die bevorzugte Substituentenklasse, da nur die Ester geschlossene, defektfreie und mehrheitlich transparente Beschichtungsfilme bildeten, die exzellente bis sehr gute Haftfestigkeiten (ISO Klasse: 0 und 1) auf Glas besaßen. Die Ether bildeten mehrheitlich brüchige Filme. Basierend auf der Kombination der Ergebnisse aus Lösemittelaustausch, den rheologischen Untersuchungen und zusätzlichen Oberflächenspannungsmessungen (30-61 mN/m) konnte geschlossen werden, dass wahrscheinlich fehlende oder schlechte Haftfestigkeiten vorrangig akkumuliertem Wasser in den Beschichtungsfilmen (visuell: trüb oder weiß) geschuldet sind, während die Brüchigkeit vermutlich auf Wechselwirkungen (H-Brücken Wechselwirkungen, hydrophobe Wechselwirkungen) zwischen den Polymeren zurückgeführt werden kann.
Insgesamt scheint die Kombination aus Kartoffelstärke basierend auf dem OCl--Abbau mit Mw < 7·10^5 g/mol und einem Estersubstituenten eine gute Wahl für wasserbasierte Dispersionen mit hohen Feststoffkonzentrationen (> 30 %), guter Filmbildung und exzellenten Haftungen auf Glas zu sein.
Hepcidin-25 (Hep-25) plays a crucial role in the control of iron homeostasis. Since the dysfunction of the hepcidin pathway leads to multiple diseases as a result of iron imbalance, hepcidin represents a potential target for the diagnosis and treatment of disorders of iron metabolism. Despite intense research in the last decade targeted at developing a selective immunoassay for iron disorder diagnosis and treatment and better understanding the ferroportin-hepcidin interaction, questions remain. The key to resolving these underlying questions is acquiring exact knowledge of the 3D structure of native Hep-25. Since it was determined that the N-terminus, which is responsible for the bioactivity of Hep-25, contains a small Cu(II)-binding site known as the ATCUN motif, it was assumed that the Hep-25-Cu(II) complex is the native, bioactive form of the hepcidin. This structure has thus far not been elucidated in detail. Owing to the lack of structural information on metal-bound Hep-25, little is known about its possible biological role in iron metabolism. Therefore, this work is focused on structurally characterizing the metal-bound Hep-25 by NMR spectroscopy and molecular dynamics simulations. For the present work, a protocol was developed to prepare and purify properly folded Hep-25 in high quantities. In order to overcome the low solubility of Hep-25 at neutral pH, we introduced the C-terminal DEDEDE solubility tag. The metal binding was investigated through a series of NMR spectroscopic experiments to identify the most affected amino acids that mediate metal coordination. Based on the obtained NMR data, a structural calculation was performed in order to generate a model structure of the Hep-25-Ni(II) complex. The DEDEDE tag was excluded from the structural calculation due to a lack of NMR restraints. The dynamic nature and fast exchange of some of the amide protons with solvent reduced the overall number of NMR restraints needed for a high-quality structure. The NMR data revealed that the 20 Cterminal Hep-25 amino acids experienced no significant conformational changes, compared to published results, as a result of a pH change from pH 3 to pH 7 and metal binding. A 3D model of the Hep-25-Ni(II) complex was constructed from NMR data recorded for the hexapeptideNi(II) complex and Hep-25-DEDEDE-Ni(II) complex in combination with the fixed conformation of 19 C-terminal amino acids. The NMR data of the Hep-25-DEDEDE-Ni(II) complex indicates that the ATCUN motif moves independently from the rest of the structure. The 3D model structure of the metal-bound Hep-25 allows for future works to elucidate hepcidin’s interaction with its receptor ferroportin and should serve as a starting point for the development of antibodies with improved selectivity.
The fabrication of 1D nanostrands composed of stimuli responsive microgels has been shown in this work. Microgels are well known materials able to respond to various stimuli from outer environment. Since these microgels respond via a volume change to an external stimulus, a targeted mechanical response can be achieved. Through carefully choosing the right composition of the polymer matrix, microgels can be designed to react precisely to the targeted stimuli (e.g. drug delivery via pH and temperature changes, or selective contractions through changes in electrical current125).
In this work, it was aimed to create flexible nano-filaments which are capable of fast anisotropic contractions similar to muscle filaments. For the fabrication of such filaments or strands, nanostructured templates (PDMS wrinkles) were chosen due to a facile and low-cost fabrication and versatile tunability of their dimensions. Additionally, wrinkling is a well-known lithography-free method which enables the fabrication of nanostructures in a reproducible manner and with a high long-range periodicity.
In Chapter 2.1, it was shown for the first time that microgels as soft matter particles can be aligned to densely packed microgel arrays of various lateral dimensions. The alignment of microgels with different compositions (e.g. VCL/AAEM, NIPAAm, NIPAAm/VCL and charged microgels) was shown by using different assembly techniques (e.g. spin-coating, template confined molding). It was chosen to set one experimental parameter constant which was the SiOx surface composition of the templates and substrates (e.g. oxidized PDMS wrinkles, Si-wafers and glass slides). It was shown that the fabrication of nanoarrays was feasible with all tested microgel types. Although the microgels exhibited different deformability when aligned on a flat surface, they retained their thermo-responsivity and swelling behavior.
Towards the fabrication of 1D microgel strands interparticle connectivity was aspired. This was achieved via different cross-linking methods (i.e. cross-linking via UV-irradiation and host-guest complexation) discussed in Chapter 2.2. The microgel arrays created by different assembly methods and microgel types were tested for their cross-linking suitability. It was observed that NIPAAm based microgels cannot be cross-linked with UV light. Furthermore, it was found that these microgels exhibit a strong surface-particle-interaction and therefore could not be detached from the given substrates. In contrast to the latter, with VCL/AAEM based microgels it was possible to both UV cross-link them based on the keto-enol tautomerism of the AAEM copolymer, and to detach them from the substrate due to the lower adhesion energy towards SiOx surfaces. With VCL/AAEM microgels long, one-dimensional microgel strands could be re-dispersed in water for further analysis. It has also been shown that at least one lateral dimension of the free dispersed 1D microgel strands is easily controllable by adjusting the wavelength of the wrinkled template. For further work, only VCL/AAEM based microgels were used to focus on the main aim of this work, i.e. the fabrication of 1D microgel nanostrands.
As an alternative to the unspecific and harsh UV cross-linking, the host-guest complexation via diazobenzene cross-linkers and cyclodextrin hosts was explored. The idea behind this approach was to give means to a future construction kit-like approach by incorporation of cyclodextrin comonomers in a broad variety of particle systems (e.g. microgels, nanoparticles). For this purpose, VCL/AAEM microgels were copolymerized with different amounts of mono-acrylate functionalized β-cyclodextrin (CD). After successfully testing the cross-linking capability in solution, the cross-linking of aligned VCL/AAEM/CD microgels was tried. Although the cross-linking worked well, once the single arrays came into contact to each other, they agglomerated. As a reason for this behavior residual amounts of mono-complexed diazobenzene linkers were suspected. Thus, end-capping strategies were tried out (e.g. excess amounts of β-cyclodextrin and coverage with azobenzene functionalized AuNPs) but were unsuccessful. With deeper thought, entropy effects were taken into consideration which favor the release of complexed diazobenzene linker leading to agglomerations. To circumvent this entropy driven effect, a multifunctional polymer with 50% azobenzene groups (Harada polymer) was used. First experiments with this polymer showed promising results regarding a less pronounced agglomeration (Figure 77). Thus, this approach could be pursued in the future. In this chapter it was found out that in contrast to pearl necklace and ribbon like formations, particle alignment in zigzag formation provided the best compromise in terms of stability in dispersion (see Figure 44a and Figure 51) while maintaining sufficient flexibility.
For this reason, microgel strands in zigzag formation were used for the motion analysis described in Chapter 2.3. The aim was to observe the properties of unrestrained microgel strands in solution (e.g. diffusion behavior, rotational properties and ideally, anisotropic contraction after temperature increase). Initially, 1D microgel strands were manipulated via AFM in a liquid cell setup. It could be observed that the strands required a higher load force compared to single microgels to be detached from the surface. However, with the AFM it was not possible to detach the strands in a controllable manner but resulted in a complete removal of single microgel particles and a tearing off the strands from the surface, respectively. For this reason, to observe the motion behavior of unrestrained microgel strands in solution, confocal microscopy was used. Furthermore, to hinder an adsorption of the strands, it was found out that coating the surface of the substrates with a repulsive polymer film was beneficial. Confocal and wide-field microscopy videos showed that the microgel strands exhibit translational and rotational diffusive motion in solution without perceptible bending. Unfortunately, with these methods the detection of the anisotropic stimuli responsive contraction of the free moving microgel strands was not possible. To summarize, the flexibility of microgel strands is more comparable to the mechanical behavior of a semi flexible cable than to a yarn. The strands studied here consist of dozens or even hundreds of discrete submicron units strung together by cross-linking, having few parallels in nanotechnology.
With the insights gained in this work on microgel-surface interactions, in the future, a targeted functionalization of the template and substrate surfaces can be conducted to actively prevent unwanted microgel adsorption for a given microgel system (e.g. PVCL and polystyrene coating235). This measure would make the discussed alignment methods more diverse. As shown herein, the assembly methods enable a versatile microgel alignment (e.g. microgel meshes, double and triple strands). To go further, one could use more complex templates (e.g. ceramic rhombs and star shaped wrinkles (Figure 14) to expand the possibilities of microgel alignment and to precisely control their aspect ratios (e.g. microgel rods with homogeneous size distributions).
Im Rahmen dieser Dissertation konnten neue Kalium- und Natrium-Ionen Fluoreszenzfarbstoffe von der Klasse der Fluoroionophore synthetisiert und charakterisiert werden. Sie bestehen aus einem N Phenylazakronenether als Ionophor und unterschiedlichen Fluorophoren und sind über einen π-konjugierten 1,2,3-Triazol-1,4-diyl Spacer verbunden. Dabei lag der Fokus während ihrer Entwicklung darauf, diese in ihrer Sensitivität, Selektivität und in ihren photophysikalischen Eigenschaften so zu funktionalisieren, dass sie für intra- bzw. extrazelluläre Konzentrationsbestimmungen geeignet sind.
Durch Variation der in ortho Position der N-Phenylazakronenether befindlichen Alkoxy-Gruppen und der fluorophoren Gruppe der Fluoroionophore konnte festgestellt werden, dass die Sensitivität und Selektivität für Kalium- bzw. Natrium-Ionen jeweils durch eine bestimmte Isomerie der 1,2,3-Triazol-1,4-diyl-Einheit erhöht wird. Des Weiteren wurde gezeigt, dass durch eine erhöhte Einschränkung der N,N-Diethylamino-Gruppe des Fluorophors eine Steigerung der Fluoreszenzquantenausbeute und eine Verschiebung des Emissionsmaximums auf über 500 nm erreicht werden konnte. Die Einführung einer Isopropoxy-Gruppe an einem N-Phenylaza-[18]krone-6-ethers resultierte dabei in einem hoch selektiven Kalium-Ionen Fluoroionophor und ermöglichte eine in vitro Überwachung von 10 – 80 mM Kalium-Ionen. Die Substitution einer Methoxy-Gruppe an einem N-Phenylaza-[15]krone-5-ether kombiniert mit unterschiedlich N,N-Diethylamino-Coumarinen lieferte hingegen zwei Natrium-Ionen Fluoroionophore, die für die Überwachung von intra- bzw. extrazellulären Natrium-Ionen Konzentrationen geeignet sind.
In einem weiteren Schritt wurden N-Phenylaza-[18]krone-6-ether mit einem Fluorophor, basierend auf einem [1,3]-Dioxolo[4,5-f][1,3]benzodioxol-(DBD)-Grundgerüst, funktionalisiert. Die im Anschluss durchgeführten spektroskopischen Untersuchungen ergaben, dass die Isopropoxy-Gruppe in ortho Position des N-Phenylaza-[18]krone-6-ether in einen für extrazelluläre Kalium-Ionen Konzentrationen selektiven Fluoroionophor resultierte, der die Konzentrationsbestimmungen über die Fluoreszenzintensität und -lebensdauer ermöglicht.
In einem abschließenden Schritt konnte unter Verwendung eines Pyrens als fluorophore Gruppe ein weiterer für extrazelluläre Kalium-Ionen Konzentrationen geeigneter Fluoroionophor entwickelt werden. Die Bestimmung der Kalium-Ionen Konzentration erfolgte hierbei anhand der Fluoreszenzintensitätsverhältnisse bei zwei Emissionswellenlängen.
Insgesamt konnten 17 verschiedene neue Fluoroionophore für die Bestimmung von Kalium- bzw. Natrium-Ionen synthetisiert und charakterisiert werden. Sechs dieser neuen Moleküle ermöglichen in vitro Messungen der intra- oder extrazellulären Kalium- und Natrium-Ionen Konzentrationen und könnten zukünftig für in vivo Konzentrationsmessungen verwendet werden.
Supercapacitors are electrochemical energy storage devices with rapid charge/discharge rate and long cycle life. Their biggest challenge is the inferior energy density compared to other electrochemical energy storage devices such as batteries. Being the most widely spread type of supercapacitors, electrochemical double-layer capacitors (EDLCs) store energy by electrosorption of electrolyte ions on the surface of charged electrodes. As a more recent development, Na-ion capacitors (NICs) are expected to be a more promising tactic to tackle the inferior energy density due to their higher-capacity electrodes and larger operating voltage. The charges are simultaneously stored by ion adsorption on the capacitive-type cathode surface and via faradic process in the battery-type anode, respectively. Porous carbon electrodes are of great importance in these devices, but the paramount problems are the facile synthetic routes for high-performance carbons and the lack of fundamental understanding of the energy storage mechanisms. Therefore, the aim of the present dissertation is to develop novel synthetic methods for (nitrogen-doped) porous carbon materials with superior performance, and to reveal a deeper understanding energy storage mechanisms of EDLCs and NICs.
The first part introduces a novel synthetic method towards hierarchical ordered meso-microporous carbon electrode materials for EDLCs. The large amount of micropores and highly ordered mesopores endow abundant sites for charge storage and efficient electrolyte transport, respectively, giving rise to superior EDLC performance in different electrolytes. More importantly, the controversial energy storage mechanism of EDLCs employing ionic liquid (IL) electrolytes is investigated by employing a series of porous model carbons as electrodes. The results not only allow to conclude on the relations between the porosity and ion transport dynamics, but also deliver deeper insights into the energy storage mechanism of IL-based EDLCs which is different from the one usually dominating in solvent-based electrolytes leading to compression double-layers.
The other part focuses on anodes of NICs, where novel synthesis of nitrogen-rich porous carbon electrodes and their sodium storage mechanism are investigated. Free-standing fibrous nitrogen-doped carbon materials are synthesized by electrospinning using the nitrogen-rich monomer (hexaazatriphenylene-hexacarbonitrile, C18N12) as the precursor followed by condensation at high temperature. These fibers provide superior capacity and desirable charge/discharge rate for sodium storage. This work also allows insights into the sodium storage mechanism in nitrogen-doped carbons. Based on this mechanism, further optimization is done by designing a composite material composed of nitrogen-rich carbon nanoparticles embedded in conductive carbon matrix for a better charge/discharge rate. The energy density of the assembled NICs significantly prevails that of common EDLCs while maintaining the high power density and long cycle life.
Due to its bioavailability and (bio)degradability, poly(lactide) (PLA) is an interesting polymer that is already being used as packaging material, surgical seam, and drug delivery system. Dependent on various parameters such as polymer composition, amphiphilicity, sample preparation, and the enantiomeric purity of lactide, PLA in an amphiphilic block copolymer can affect the self-assembly behavior dramatically. However, sizes and shapes of aggregates have a critical effect on the interactions between biological and drug delivery systems, where the general understanding of these polymers and their ability to influence self-assembly is of significant interest in science.
The first part of this thesis describes the synthesis and study of a series of linear poly(L-lactide) (PLLA) and poly(D-lactide) (PDLA)-based amphiphilic block copolymers with varying PLA (hydrophobic), and poly(ethylene glycol) (PEG) (hydrophilic) chain lengths and different block copolymer sequences (PEG-PLA and PLA-PEG). The PEG-PLA block copolymers were synthesized by ring-opening polymerization of lactide initiated by a PEG-OH macroinitiator. In contrast, the PLA-PEG block copolymers were produced by a Steglich-esterification of modified PLA with PEG-OH.
The aqueous self-assembly at room temperature of the enantiomerically pure PLLA-based block copolymers and their stereocomplexed mixtures was investigated by dynamic light scattering (DLS), transmission electron microscopy (TEM), wide-angle X-ray diffraction (WAXD), and differential scanning calorimetry (DSC). Spherical micelles and worm-like structures were produced, whereby the obtained self-assembled morphologies were affected by the lactide weight fraction in the block copolymer and self-assembly time. The formation of worm-like structures increases with decreasing PLA-chain length and arises from spherical micelles, which become colloidally unstable and undergo an epitaxial fusion with other micelles. As shown by DSC experiments, the crystallinity of the corresponding PLA blocks increases within the self-assembly time. However, the stereocomplexed self-assembled structures behave differently from the parent polymers and result in irregular-shaped clusters of spherical micelles. Additionally, time-dependent self-assembly experiments showed a transformation, from already self-assembled morphologies of different shapes to more compact micelles upon stereocomplexation.
In the second part of this thesis, with the objective to influence the self-assembly of PLA-based block copolymers and its stereocomplexes, poly(methyl phosphonate) (PMeP) and poly(isopropyl phosphonate) (PiPrP) were produced by ring-opening polymerization to implement an alternative to the hydrophilic block PEG. Although, the 1,8 diazabicyclo[5.4.0]unde 7 ene (DBU) or 1,5,7 triazabicyclo[4.4.0]dec-5-ene (TBD) mediated synthesis of the corresponding poly(alkyl phosphonate)s was successful, however, not so the polymerization of copolymers with PLA-based precursors (PLA-homo polymers, and PEG-PLA block copolymers). Transesterification, obtained by 1H-NMR spectroscopy, between the poly(phosphonate)- and PLA block caused a high-field shifted peak split of the methine proton in the PLA polymer chain, with split intensities depending on the used catalyst (DBU for PMeP, and TBD for PiPrP polymerization). An additional prepared block copolymer PiPrP-PLLA that wasn’t affected in its polymer sequence was finally used for self-assembly experiments with PLA-PEG and PEG-PLA mixing.
This work provides a comprehensive study of the self-assembly behavior of PLA-based block copolymers influenced by various parameters such as polymer block lengths, self-assembly time, and stereocomplexation of block copolymer mixtures.
The central motivation of the thesis was to provide possible solutions and concepts to improve the performance (e.g. activity and selectivity) of electrochemical N2 reduction reaction (NRR). Given that porous carbon-based materials usually exhibit a broad range of structural properties, they could be promising NRR catalysts. Therefore, the advanced design of novel porous carbon-based materials and the investigation of their application in electrocatalytic NRR including the particular reaction mechanisms are the most crucial points to be addressed. In this regard, three main topics were investigated. All of them are related to the functionalization of porous carbon for electrochemical NRR or other electrocatalytic reactions.
In chapter 3, a novel C-TixOy/C nanocomposite has been described that has been obtained via simple pyrolysis of MIL-125(Ti). A novel mode for N2 activation is achieved by doping carbon atoms from nearby porous carbon into the anion lattice of TixOy. By comparing the NRR performance of M-Ts and by carrying out DFT calculations, it is found that the existence of (O-)Ti-C bonds in C-doped TixOy can largely improve the ability to activate and reduce N2 as compared to unoccupied OVs in TiO2. The strategy of rationally doping heteroatoms into the anion lattice of transition metal oxides to create active centers may open many new opportunities beyond the use of noble metal-based catalysts also for other reactions that require the activation of small molecules as well.
In chapter 4, a novel catalyst construction composed of Au single atoms decorated on the surface of NDPCs was reported. The introduction of Au single atoms leads to active reaction sites, which are stabilized by the N species present in NDPCs. Thus, the interaction within as-prepared AuSAs-NDPCs catalysts enabled promising performance for electrochemical NRR. For the reaction mechanism, Au single sites and N or C species can act as Frustrated Lewis pairs (FLPs) to enhance the electron donation and back-donation process to activate N2 molecules. This work provides new opportunities for catalyst design in order to achieve efficient N2 fixation at ambient conditions by utilizing recycled electric energy.
The last topic described in chapter 5 mainly focused on the synthesis of dual heteroatom-doped porous carbon from simple precursors. The introduction of N and B heteroatoms leads to the construction of N-B motives and Frustrated Lewis pairs in a microporous architecture which is also rich in point defects. This can improve the strength of adsorption of different reactants (N2 and HMF) and thus their activation. As a result, BNC-2 exhibits a desirable electrochemical NRR and HMF oxidation performance. Gas adsorption experiments have been used as a simple tool to elucidate the relationship between the structure and catalytic activity. This work provides novel and deep insights into the rational design and the origin of activity in metal-free electrocatalysts and enables a physically viable discussion of the active motives, as well as the search for their further applications.
Throughout this thesis, the ubiquitous problems of low selectivity and activity of electrochemical NRR are tackled by designing porous carbon-based catalysts with high efficiency and exploring their catalytic mechanisms. The structure-performance relationships and mechanisms of activation of the relatively inert N2 molecules are revealed by either experimental results or DFT calculations. These fundamental understandings pave way for a future optimal design and targeted promotion of NRR catalysts with porous carbon-based structure, as well as study of new N2 activation modes.
Cellulose derived polymers
(2019)
Plastics, such as polyethylene, polypropylene, and polyethylene terephthalate are part of our everyday lives in the form of packaging, household goods, electrical insulation, etc. These polymers are non-degradable and create many environmental problems and public health concerns. Additionally, these polymers are produced from finite fossils resources. With the continuous utilization of these limited resources, it is important to look towards renewable sources along with biodegradation of the produced polymers, ideally. Although many bio-based polymers are known, such as polylactic acid, polybutylene succinate adipate or polybutylene succinate, none have yet shown the promise of replacing conventional polymers like polyethylene, polypropylene and polyethylene terephthalate. Cellulose is one of the most abundant renewable resources produced in nature. It can be transformed into various small molecules, such as sugars, furans, and levoglucosenone. The aim of this research is to use the cellulose derived molecules for the synthesis of polymers.
Acid-treated cellulose was subjected to thermal pyrolysis to obtain levoglucosenone, which was reduced to levoglucosenol. Levoglucosenol was polymerized, for the first time, by ring-opening metathesis polymerization (ROMP) yielding high molar mass polymers of up to ~150 kg/mol. The poly(levoglucosenol) is thermally stable up to ~220 ℃, amorphous, and is exhibiting a relatively high glass transition temperature of ~100 ℃. The poly(levoglucosenol) can be converted to a transparent film, resembling common plastic, and was found to degrade in a moist acidic environment. This means that poly(levoglucosenol) may find its use as an alternative to conventional plastic, for instance, polystyrene.
Levoglucosenol was also converted into levoglucosenyl methyl ether, which was polymerized by cationic ring-opening metathesis polymerization (CROP). Polymers were obtained with molar masses up to ~36 kg/mol. These polymers are thermally stable up to ~220 ℃ and are semi-crystalline thermoplastics, having a glass transition temperature of ~35 ℃ and melting transition of 70-100 ℃. Additionally, the polymers underwent cross-linking, hydrogenation and thiol-ene click chemistry.
Aluminum oxide is an Earth-abundant geological material, and its interaction with water is of crucial importance for geochemical and environmental processes. Some aluminum oxide surfaces are also known to be useful in heterogeneous catalysis, while the surface chemistry of aqueous oxide interfaces determines the corrosion, growth and dissolution of such materials. In this doctoral work, we looked mainly at the (0001) surface of α-Al 2 O 3 and its reactivity towards water. In particular, a great focus of this work is dedicated to simulate and address the vibrational spectra of water adsorbed on the α-alumina(0001) surface in various conditions and at different coverages. In fact, the main source of comparison and inspiration for this work comes from the collaboration with the “Interfacial Molecular Spectroscopy” group led by Dr. R. Kramer Campen at the Fritz-Haber Institute of the MPG in Berlin. The expertise of our project partners in surface-sensitive Vibrational Sum Frequency (VSF) generation spectroscopy was crucial to develop and adapt specific simulation schemes used in this work. Methodologically, the main approach employed in this thesis is Ab Initio Molecular Dynamics (AIMD) based on periodic Density Functional Theory (DFT) using the PBE functional with D2 dispersion correction. The analysis of vibrational frequencies from both a static and a dynamic, finite-temperature perspective offers the ability to investigate the water / aluminum oxide interface in close connection to experiment.
The first project presented in this work considers the characterization of dissociatively adsorbed deuterated water on the Al-terminated (0001) surface. This particular structure is known from both experiment and theory to be the thermodynamically most stable surface termination of α-alumina in Ultra-High Vacuum (UHV) conditions. Based on experiments performed by our colleagues at FHI, different adsorption sites and products have been proposed and identified for D 2 O. While previous theoretical investigations only looked at vibrational frequencies of dissociated OD groups by staticNormal Modes Analysis (NMA), we rather employed a more sophisticated approach to directly assess vibrational spectra (like IR and VSF) at finite temperature from AIMD. In this work, we have employed a recent implementation which makes use of velocity-velocity autocorrelation functions to simulate such spectral responses of O-H(D) bonds. This approach allows for an efficient and qualitatively accurate estimation of Vibrational Densities of States (VDOS) as well as IR and VSF spectra, which are then tested against experimental spectra from our collaborators.
In order to extend previous work on unimolecularly dissociated water on α-Al 2 O 3 , we then considered a different system, namely, a fully hydroxylated (0001) surface, which results from the reconstruction of the UHV-stable Al-terminated surface at high water contents. This model is then further extended by considering a hydroxylated surface with additional water molecules, forming a two-dimensional layer which serves as a potential template to simulate an aqueous interface in environmental conditions. Again, employing finite-temperature AIMD trajectories at the PBE+D2 level, we investigated the behaviour of both hydroxylated surface (HS) and the water-covered structure derived from it (known as HS+2ML). A full range of spectra, from VDOS to IR and VSF, is then calculated using the same methodology, as described above. This is the main focus of the second project, reported in Chapter 5. In this case, comparison between theoretical spectra and experimental data is definitely good. In particular, we underline the nature of high-frequency resonances observed above 3700 cm −1 in VSF experiments to be associated with surface OH-groups, known as “aluminols” which are a key fingerprint of the fully hydroxylated surface.
In the third and last project, which is presented in Chapter 6, the extension of VSF spectroscopy experiments to the time-resolved regime offered us the opportunity to investigate vibrational energy relaxation at the α-alumina / water interface. Specifically, using again DFT-based AIMD simulations, we simulated vibrational lifetimes for surface aluminols as experimentally detected via pump-probe VSF. We considered the water-covered HS model as a potential candidate to address this problem. The vibrational (IR) excitation and subsequent relaxation is performed by means of a non-equilibrium molecular dynamics scheme. In such a scheme, we specifically looked at the O-H stretching mode of surface aluminols. Afterwards, the analysis of non-equilibrium trajectories allows for an estimation of relaxation times in the order of 2-4 ps which are in overall agreement with measured ones.
The aim of this work has been to provide, within a consistent theoretical framework, a better understanding of vibrational spectroscopy and dynamics for water on the α-alumina(0001) surface,ranging from very low water coverage (similar to the UHV case) up to medium-high coverages, resembling the hydroxylated oxide in environmental moist conditions.
The growing energy demand of the modern economies leads to the increased consumption of fossil fuels in form of coal, oil, and natural gases, as the mains sources. The combustion of these carbon-based fossil fuels is inevitably producing greenhouse gases, especially CO2. Approaches to tackle the CO2 problem are to capture it from the combustion sources or directly from air, as well as to avoid CO2 production in energy consuming sources (e.g., in the refrigeration sector). In the former, relatively low CO2 concentrations and competitive adsorption of other gases is often leading to low CO2 capacities and selectivities. In both approaches, the interaction of gas molecules with porous materials plays a key role. Porous carbon materials possess unique properties including electric conductivity, tunable porosity, as well as thermal and chemical stability. Nevertheless, pristine carbon materials offer weak polarity and thus low CO2 affinity. This can be overcome by nitrogen doping, which enhances the affinity of carbon materials towards acidic or polar guest molecules (e.g., CO2, H2O, or NH3). In contrast to heteroatom-free materials, such carbon materials are in most cases “noble”, that is, they oxidize other matter rather than being oxidized due to the very positive working potential of their electrons. The challenging task here is to achieve homogenous distribution of significant nitrogen content with similar bonding motives throughout the carbon framework and a uniform pore size/distribution to maximize host-guest interactions. The aim of this thesis is the development of novel synthesis pathways towards nitrogen-doped nanoporous noble carbon materials with precise design on a molecular level and understanding of their structure-related performance in energy and environmental applications, namely gas adsorption and electrochemical energy storage.
A template-free synthesis approach towards nitrogen-doped noble microporous carbon materials with high pyrazinic nitrogen content and C2N-type stoichiometry was established via thermal condensation of a hexaazatriphenylene derivative. The materials exhibited high uptake of guest molecules, such as H2O and CO2 at low concentrations, as well as moderate CO2/N2 selectivities. In the following step, the CO2/N2 selectivity was enhanced towards molecular sieving of CO2 via kinetic size exclusion of N2. The precise control over the condensation degree, and thus, atomic construction and porosity of the resulting materials led to remarkable CO2/N2 selectivities, CO2 capacities, and heat of CO2 adsorption. The ultrahydrophilic nature of the pore walls and the narrow microporosity of these carbon materials served as ideal basis for the investigation of interface effects with more polar guest molecules than CO2, namely H2O and NH3.
H2O vapor physisorption measurements, as well as NH3-temperature programmed desorption and thermal response measurements showed exceptionally high affinity towards H2O vapor and NH3 gas. Another series of nitrogen-doped carbon materials was synthesized by direct condensation of a pyrazine-fused conjugated microporous polymer and their structure-related performance in electrochemical energy storage, namely as anode materials for sodium-ion battery, was investigated.
All in all, the findings in this thesis exemplify the value of molecularly designed nitrogen-doped carbon materials with remarkable heteroatom content implemented as well-defined structure motives. The simultaneous adjustment of the porosity renders these materials suitable candidates for fundamental studies about the interactions between nitrogen-doped carbon materials and different guest species.