Refine
Has Fulltext
- yes (3) (remove)
Document Type
- Postprint (2)
- Doctoral Thesis (1)
Is part of the Bibliography
- yes (3)
Keywords
- microscopy (3) (remove)
Institute
In this paper two groups supporting different views on the mechanism of light induced polymer deformation argue about the respective underlying theoretical conceptions, in order to bring this interesting debate to the attention of the scientific community. The group of Prof. Nicolae Hurduc supports the model claiming that the cyclic isomerization of azobenzenes may cause an athermal transition of the glassy azobenzene containing polymer into a fluid state, the so-called photo-fluidization concept. This concept is quite convenient for an intuitive understanding of the deformation process as an anisotropic flow of the polymer material. The group of Prof. Svetlana Santer supports the re-orientational model where the mass-transport of the polymer material accomplished during polymer deformation is stated to be generated by the light-induced re-orientation of the azobenzene side chains and as a consequence of the polymer backbone that in turn results in local mechanical stress, which is enough to irreversibly deform an azobenzene containing material even in the glassy state. For the debate we chose three polymers differing in the glass transition temperature, 32 °C, 87 °C and 95 °C, representing extreme cases of flexible and rigid materials. Polymer film deformation occurring during irradiation with different interference patterns is recorded using a homemade set-up combining an optical part for the generation of interference patterns and an atomic force microscope for acquiring the kinetics of film deformation. We also demonstrated the unique behaviour of azobenzene containing polymeric films to switch the topography in situ and reversibly by changing the irradiation conditions. We discuss the results of reversible deformation of three polymers induced by irradiation with intensity (IIP) and polarization (PIP) interference patterns, and the light of homogeneous intensity in terms of two approaches: the re-orientational and the photo-fluidization concepts. Both agree in that the formation of opto-mechanically induced stresses is a necessary prerequisite for the process of deformation. Using this argument, the deformation process can be characterized either as a flow or mass transport.
The synthesis and photophysical properties of two new FRET pairs based on coumarin as a donor and DBD dye as an acceptor are described. The introduction of a bromo atom dramatically increases the two-photon excitation (2PE) cross section providing a 2PE-FRET system, which is also suitable for 2PE-FLIM.
Die vorliegende Arbeit beschäftigte sich mit zwei Themengebieten. Es ging zum einen um die mechanischen Eigenschaften von Polyelektrolythohlkapseln und zum anderen um die Adhäsion von Polyelektrolythohlkapseln. Die mechanischen Eigenschaften wurden mit der AFM „colloidal probe” Technik untersucht. Dabei zeigte sich, dass die Kraftdeformationskurven für kleine Deformationen den nach der Schalentheorie vorhergesagten linearen Verlauf haben. Ebenso wurde die quadratische Abhängigkeit der Federkonstanten von der Dicke bestätigt. Für PAH/PSS findet man einen E-Modul von 0.25 GPa. Zusammen mit der Tatsache, dass die Deformationskurven unabhängig von der Geschwindigkeit sind und praktisch keine Hysterese zeigen, sowie der Möglichkeit die Kapseln plastisch zu deformieren, kann man schließen, dass das System in einem glasartigen Zustand vorliegt. <pt>Erwartungsgemäß zeigte der pH einen starken Einfluss auf die PEM. Während in einem pH-Bereich zwischen 2 und 11.5 keine morphologischen Änderungen festgestellt werden konnten, vergrößerte sich der Radius bei pH = 12 um bis zu 50 %. Diese Radienänderung war reversibel und ging einher mit einem sichtbaren Weicherwerden der Kapseln. Eine Abnahme des E-Moduls um mindestens drei Größenordungen wurde durch Kraftdeformationsmessungen bestätigt. Die Kraftdeformationskurven zeigen eine starke Hysterese. Das System befindet sich nun nicht mehr in einem glasartigen Zustand, sondern ist viskos bis gummiartig geworden. Messungen an Kapseln, die mit Glutardialdehyd behandelt wurden, zeigten, dass die Behandlung das pH-abhängige Verhalten verändert. Dies kann darauf zurückgeführt werden, dass das PAH durch den Glutardialdehyd quervernetzt wird. Bei einem hohen Quervernetzungsgrad, zeigen die Kapseln keine Änderung des mechanischen Verhaltens bei pH = 12. Schwach quervernetzte Kapseln werden immer noch signifikant weicher bei pH = 12, jedoch ändert sich der Radius nicht. Außerdem wurden Multilagenkapseln untersucht, deren Stabilität nicht auf elektrostatischen Wechselwirkungen sondern auf Wasserstoffbrückenbindungen beruhte. Diese Kapseln zeigten eine deutlich höhere Steifigkeit mit E-Modulen bis zu 1 GPa. Es wurde gefunden, dass auch dieses System für kleine Deformationen ein lineares Kraft-Deformationsverhalten zeigt, und dass die Federkonstante quadratisch von der Dicke abhängt. Die Kapseln lösen sich praktisch sofort bei pH = 6.5 auf. In der Nähe dieses pHs konnte das Abnehmen der Federkonstanten verfolgt werden. Außerdem wurde das Adhäsionsverhalten von PAH/PSS Kapseln auf mit PEI-beschichtetem Glas untersucht. Die Adhäsionsflächen waren zu einem großen Teil rund und ließen sich quantitativ auswerten. Der Adhäsionsradius nimmt mit dem Kapselradius zu und mit der Dicke ab. Das Verhalten konnte mit zwei Modellen, einem für die große und einem für die kleine Deformation beschrieben werden. Das große Deformationsmodell liefert um eine Größenordung niedrigere Adhäsionsenergien als das kleine Deformationsmodell, welches mit Werten von ‑0.2 mJ/m<sup>2 Werte in einem plausiblen Bereich liefert. Es wurde gefunden, dass bei einem Verhältnis von Dicke zu Deformation von etwa eins "buckling" auftritt. Dieser Punkt markierte zugleich den Übergang von der großen zur kleinen Deformation.