Refine
Has Fulltext
- yes (41) (remove)
Year of publication
- 2016 (41) (remove)
Document Type
- Doctoral Thesis (26)
- Postprint (13)
- Habilitation Thesis (1)
- Report (1)
Keywords
- earthquake (3)
- Bodenfeuchte (2)
- Erdbeben (2)
- Erosion (2)
- Geologie (2)
- Geomorphologie (2)
- Klimawandel (2)
- Neotektonik (2)
- Thermochronologie (2)
- climate change (2)
Institute
- Institut für Geowissenschaften (41) (remove)
The Earth’s shallow subsurface with sedimentary cover acts as a waveguide to any incoming wavefield. Within the framework of my thesis, I focused on the characterization of this shallow subsurface within tens to few hundreds of meters of sediment cover. I imaged the seismic 1D shear wave velocity (and possibly the 1D compressional wave velocity). This information is not only required for any seismic risk assessment, geotechnical engineering or microzonation activities, but also for exploration and global seismology where site effects are often neglected in seismic waveform modeling.
First, the conventional frequency-wavenumber (f - k) technique is used to derive the dispersion characteristic of the propagating surface waves recorded using distinct arrays of seismometers in 1D and 2D configurations. Further, the cross-correlation technique is applied to seismic array data to estimate the Green’s function between receivers pairs combination assuming one is the source and the other the receiver. With the consideration of a 1D media, the estimated cross-correlation Green’s functions are sorted with interstation distance in a virtual 1D active seismic experiment. The f - k technique is then used to estimate the dispersion curves. This integrated analysis is important for the interpretation of a large bandwidth of the phase velocity dispersion curves and therefore improving the resolution of the estimated 1D Vs profile.
Second, the new theoretical approach based on the Diffuse Field Assumption (DFA) is used for the interpretation of the observed microtremors H/V spectral ratio. The theory is further extended in this research work to include not only the interpretation of the H/V measured at the surface, but also the H/V measured at depths and in marine environments. A modeling and inversion of synthetic H/V spectral ratio curves on simple predefined geological structures shows an almost perfect recovery of the model parameters (mainly Vs and to a lesser extent Vp). These results are obtained after information from a receiver at depth has been considered in the inversion.
Finally, the Rayleigh wave phase velocity information, estimated from array data, and the H/V(z, f) spectral ratio, estimated from a single station data, are combined and inverted for the velocity profile information. Obtained results indicate an improved depth resolution in comparison to estimations using the phase velocity dispersion curves only. The overall estimated sediment thickness is comparable to estimations obtained by inverting the full micortremor H/V spectral ratio.
In the past, floods were basically managed by flood control mechanisms. The focus was set on the reduction of flood hazard. The potential consequences were of minor interest. Nowadays river flooding is increasingly seen from the risk perspective, including possible consequences. Moreover, the large-scale picture of flood risk became increasingly important for disaster management planning, national risk developments and the (re-) insurance industry. Therefore, it is widely accepted that risk-orientated flood management ap-proaches at the basin-scale are needed. However, large-scale flood risk assessment methods for areas of several 10,000 km² are still in early stages. Traditional flood risk assessments are performed reach wise, assuming constant probabilities for the entire reach or basin. This might be helpful on a local basis, but where large-scale patterns are important this approach is of limited use. Assuming a T-year flood (e.g. 100 years) for the entire river network is unrealistic and would lead to an overestimation of flood risk at the large scale. Due to the lack of damage data, additionally, the probability of peak discharge or rainfall is usually used as proxy for damage probability to derive flood risk. With a continuous and long term simulation of the entire flood risk chain, the spatial variability of probabilities could be consider and flood risk could be directly derived from damage data in a consistent way.
The objective of this study is the development and application of a full flood risk chain, appropriate for the large scale and based on long term and continuous simulation. The novel approach of ‘derived flood risk based on continuous simulations’ is introduced, where the synthetic discharge time series is used as input into flood impact models and flood risk is directly derived from the resulting synthetic damage time series.
The bottleneck at this scale is the hydrodynamic simu-lation. To find suitable hydrodynamic approaches for the large-scale a benchmark study with simplified 2D hydrodynamic models was performed. A raster-based approach with inertia formulation and a relatively high resolution of 100 m in combination with a fast 1D channel routing model was chosen.
To investigate the suitability of the continuous simulation of a full flood risk chain for the large scale, all model parts were integrated into a new framework, the Regional Flood Model (RFM). RFM consists of the hydrological model SWIM, a 1D hydrodynamic river network model, a 2D raster based inundation model and the flood loss model FELMOps+r. Subsequently, the model chain was applied to the Elbe catchment, one of the largest catchments in Germany. For the proof-of-concept, a continuous simulation was per-formed for the period of 1990-2003. Results were evaluated / validated as far as possible with available observed data in this period. Although each model part introduced its own uncertainties, results and runtime were generally found to be adequate for the purpose of continuous simulation at the large catchment scale.
Finally, RFM was applied to a meso-scale catchment in the east of Germany to firstly perform a flood risk assessment with the novel approach of ‘derived flood risk assessment based on continuous simulations’. Therefore, RFM was driven by long term synthetic meteorological input data generated by a weather generator. Thereby, a virtual time series of climate data of 100 x 100 years was generated and served as input to RFM providing subsequent 100 x 100 years of spatially consistent river discharge series, inundation patterns and damage values. On this basis, flood risk curves and expected annual damage could be derived directly from damage data, providing a large-scale picture of flood risk. In contrast to traditional flood risk analysis, where homogenous return periods are assumed for the entire basin, the presented approach provides a coherent large-scale picture of flood risk. The spatial variability of occurrence probability is respected. Additionally, data and methods are consistent. Catchment and floodplain processes are repre-sented in a holistic way. Antecedent catchment conditions are implicitly taken into account, as well as physical processes like storage effects, flood attenuation or channel–floodplain interactions and related damage influencing effects. Finally, the simulation of a virtual period of 100 x 100 years and consequently large data set on flood loss events enabled the calculation of flood risk directly from damage distributions. Problems associated with the transfer of probabilities in rainfall or peak runoff to probabilities in damage, as often used in traditional approaches, are bypassed.
RFM and the ‘derived flood risk approach based on continuous simulations’ has the potential to provide flood risk statements for national planning, re-insurance aspects or other questions where spatially consistent, large-scale assessments are required.
The energy sector is both affected by climate change and a key sector for climate protection measures. Energy security is the backbone of our modern society and guarantees the functioning of most critical infrastructure. Thus, decision makers and energy suppliers of different countries should be familiar with the factors that increase or decrease the susceptibility of their electricity sector to climate change. Susceptibility means socioeconomic and structural characteristics of the electricity sector that affect the demand for and supply of electricity under climate change. Moreover, the relevant stakeholders are supposed to know whether the given national energy and climate targets are feasible and what needs to be done in order to meet these targets. In this regard, a focus should be on the residential building sector as it is one of the largest energy consumers and therefore emitters of anthropogenic CO 2 worldwide.
This dissertation addresses the first aspect, namely the susceptibility of the electricity sector, by developing a ranked index which allows for quantitative comparison of the electricity sector susceptibility of 21 European countries based on 14 influencing factors. Such a ranking has not been completed to date. We applied a sensitivity analysis to test the relative effect of each influencing factor on the susceptibility index ranking. We also discuss reasons for the ranking position and thus the susceptibility of selected countries. The second objective, namely the impact of climate change on the energy demand of buildings, is tackled by means of a new model with which the heating and cooling energy demand of residential buildings can be estimated. We exemplarily applied the model to Germany and the Netherlands. It considers projections of future changes in population, climate and the insulation standards of buildings, whereas most of the existing studies only take into account fewer than three different factors that influence the future energy demand of buildings. Furthermore, we developed a comprehensive retrofitting algorithm with which the total residential building stock can be modeled for the first time for each year in the past and future.
The study confirms that there is no correlation between the geographical location of a country and its position in the electricity sector susceptibility ranking. Moreover, we found no pronounced pattern of susceptibility influencing factors between countries that ranked higher or lower in the index. We illustrate that Luxembourg, Greece, Slovakia and Italy are the countries with the highest electricity sector susceptibility. The electricity sectors of Norway, the Czech Republic, Portugal and Denmark were found to be least susceptible to climate change. Knowledge about the most important factors for the poor and good ranking positions of these countries is crucial for finding adequate adaptation measures to reduce the susceptibility of the electricity sector. Therefore, these factors are described within this study.
We show that the heating energy demand of residential buildings will strongly decrease in both Germany and the Netherlands in the future. The analysis for the Netherlands focused on the regional level and a finer temporal resolution which revealed strong variations in the future heating energy demand changes by province and by month. In the German study, we additionally investigated the future cooling energy demand and could demonstrate that it will only slightly increase up to the middle of this century. Thus, increases in the cooling energy demand are not expected to offset reductions in heating energy demand. The main factor for substantial heating energy demand reductions is the retrofitting of buildings. We are the first to show that the given German and Dutch energy and climate targets in the building sector can only be met if the annual retrofitting rates are substantially increased. The current rate of only about 1 % of the total building stock per year is insufficient for reaching a nearly zero-energy demand of all residential buildings by the middle of this century. To reach this target, it would need to be at least tripled. To sum up, this thesis emphasizes that country-specific characteristics are decisive for the electricity sector susceptibility of European countries. It also shows for different scenarios how much energy is needed in the future to heat and cool residential buildings. With this information, existing climate mitigation and adaptation measures can be justified or new actions encouraged.
Extreme hydro-meteorological events, such as severe droughts or heavy rainstorms, constitute primary manifestations of climate variability and exert a critical impact on the natural environment and human society. This is particularly true for high-mountain areas, such as the eastern flank of the southern Central Andes of NW Argentina, a region impacted by deep convection processes that form the basis of extreme events, often resulting in floods, a variety of mass movements, and hillslope processes. This region is characterized by pronounced E-W gradients in topography, precipitation, and vegetation cover, spanning low to medium-elevation, humid and densely vegetated areas to high-elevation, arid and sparsely vegetated environments. This strong E-W gradient is mirrored by differences in the efficiency of surface processes, which mobilize and transport large amounts of sediment through the fluvial system, from the steep hillslopes to the intermontane basins and further to the foreland. In a highly sensitive high-mountain environment like this, even small changes in the spatiotemporal distribution, magnitude and rates of extreme events may strongly impact environmental conditions, anthropogenic activity, and the well-being of mountain communities and beyond. However, although the NW Argentine Andes comprise the catchments for the La Plata river that traverses one of the most populated and economically relevant areas of South America, there are only few detailed investigations of climate variability and extreme hydro-meteorological events.
In this thesis, I focus on deciphering the spatiotemporal variability of rainfall and river discharge, with particular emphasis on extreme hydro-meteorological events in the subtropical southern Central Andes of NW Argentina during the past seven decades. I employ various methods to assess and quantify statistically significant trend patterns of rainfall and river discharge, integrating high-quality daily time series from gauging stations (40 rainfall and 8 river discharge stations) with gridded datasets (CPC-uni and TRMM 3B42 V7), for the period between 1940 and 2015. Evidence for a general intensification of the hydrological cycle at intermediate elevations (~ 0.5 – 3 km asl) at the eastern flank of the southern Central Andes is found both from rainfall and river-discharge time-series analysis during the period from 1940 to 2015. This intensification is associated with the increase of the annual total amount of rainfall and the mean annual discharge. However, most pronounced trends are found at high percentiles, i.e. extreme hydro-meteorological events, particularly during the wet season from December to February.An important outcome of my studies is the recognition of a rapid increase in the amount of river discharge during the period between 1971 and 1977, most likely linked to the 1976-77 global climate shift, which is associated with the North Pacific Ocean sea surface temperature variability. Interestingly, after this rapid increase, both rainfall and river discharge decreased at low and intermediate elevations along the eastern flank of the Andes. In contrast, during the same time interval, at high elevations, extensive areas on the arid Puna de Atacama plateau have recorded increasing annual rainfall totals. This has been associated with more intense extreme hydro-meteorological events from 1979 to 2014. This part of the study reveals that low-, intermediate, and high-elevation sectors in the Andes of NW Argentina respond differently to changing climate conditions.
Possible forcing mechanisms of the pronounced hydro-meteorological variability observed in the study area are also investigated. For the period between 1940 and 2015, I analyzed modes of oscillation of river discharge from small to medium drainage basins (102 to 104 km2), located on the eastern flank of the orogen. First, I decomposed the relevant monthly time series using the Hilbert-Huang Transform, which is particularly appropriate for non-stationary time series that result from non-linear natural processes. I observed that in the study region discharge variability can be described by five quasi-periodic oscillatory modes on timescales varying from 1 to ~20 years. Secondly, I tested the link between river-discharge variations and large-scale climate modes of variability, using different climate indices, such as the BEST ENSO (Bivariate El Niño-Southern Oscillation Time-series) index. This analysis reveals that, although most of the variance on the annual timescale is associated with the South American Monsoon System, a relatively large part of river-discharge variability is linked to Pacific Ocean variability (PDO phases) at multi-decadal timescales (~20 years). To a lesser degree, river discharge variability is also linked to the Tropical South Atlantic (TSA) sea surface temperature anomaly at multi-annual timescales (~2-5 years).
Taken together, these findings exemplify the high degree of sensitivity of high-mountain environments with respect to climatic variability and change. This is particularly true for the topographic transitions between the humid, low-moderate elevations and the semi-arid to arid highlands of the southern Central Andes. Even subtle changes in the hydro-meteorological regime of these areas of the mountain belt react with major impacts on erosional hillslope processes and generate mass movements that fundamentally impact the transport capacity of mountain streams. Despite more severe storms in these areas, the fluvial system is characterized by pronounced variability of the stream power on different timescales, leading to cycles of sediment aggradation, the loss of agriculturally used land and severe impacts on infrastructure.
Water scarcity, adaption on climate change, and risk assessment of droughts and floods are critical topics for science and society these days. Monitoring and modeling of the hydrological cycle are a prerequisite to understand and predict the consequences for weather and agriculture. As soil water storage plays a key role for partitioning of water fluxes between the atmosphere, biosphere, and lithosphere, measurement techniques are required to estimate soil moisture states from small to large scales.
The method of cosmic-ray neutron sensing (CRNS) promises to close the gap between point-scale and remote-sensing observations, as its footprint was reported to be 30 ha. However, the methodology is rather young and requires highly interdisciplinary research to understand and interpret the response of neutrons to soil moisture. In this work, the signal of nine detectors has been systematically compared, and correction approaches have been revised to account for meteorological and geomagnetic variations. Neutron transport simulations have been consulted to precisely characterize the sensitive footprint area, which turned out to be 6--18 ha, highly local, and temporally dynamic. These results have been experimentally confirmed by the significant influence of water bodies and dry roads. Furthermore, mobile measurements on agricultural fields and across different land use types were able to accurately capture the various soil moisture states. It has been further demonstrated that the corresponding spatial and temporal neutron data can be beneficial for mesoscale hydrological modeling. Finally, first tests with a gyrocopter have proven the concept of airborne neutron sensing, where increased footprints are able to overcome local effects.
This dissertation not only bridges the gap between scales of soil moisture measurements. It also establishes a close connection between the two worlds of observers and modelers, and further aims to combine the disciplines of particle physics, geophysics, and soil hydrology to thoroughly explore the potential and limits of the CRNS method.
Das Wissen um die lokale Struktur von Seltenen Erden Elementen (SEE) in silikatischen und aluminosilikatischen Schmelzen ist von fundamentalem Interesse für die Geochemie der magmatischen Prozesse, speziell wenn es um ein umfassendes Verständnis der Verteilungsprozesse von SEE in magmatischen Systemen geht. Es ist allgemein akzeptiert, dass die SEE-Verteilungsprozesse von Temperatur, Druck, Sauerstofffugazität (im Fall von polyvalenten Kationen) und der Kristallchemie kontrolliert werden. Allerdings ist wenig über den Einfluss der Schmelzzusammensetzung selbst bekannt. Ziel dieser Arbeit ist, eine Beziehung zwischen der Variation der SEE-Verteilung mit der Schmelzzusammensetzung und der Koordinationschemie dieser SEE in der Schmelze zu schaffen.
Dazu wurden Schmelzzusammensetzungen von Prowatke und Klemme (2005), welche eine deutliche Änderung der Verteilungskoeffizienten zwischen Titanit und Schmelze ausschließlich als Funktion der Schmelzzusammensetzung zeigen, sowie haplogranitische bzw. haplobasaltische Schmelzzusammensetzungen als Vertreter magmatischer Systeme mit La, Gd, Yb und Y dotiert und als Glas synthetisiert. Die Schmelzen variierten systematisch im Aluminiumsättigungsindex (ASI), welcher bei den Prowatke und Klemme (2005) Zusammensetzungen einen Bereich von 0.115 bis 0.768, bei den haplogranitischen Zusammensetzungen einen Bereich von 0.935 bis 1.785 und bei den haplobasaltischen Zusammensetzungen einen Bereich von 0.368 bis 1.010 abdeckt. Zusätzlich wurden die haplogranitischen Zusammensetzungen mit 4 % H2O synthetisiert, um den Einfluss von Wasser auf die lokale Umgebung von SEE zu studieren. Um Informationen über die lokalen Struktur von Gd, Yb und Y zu erhalten wurde die Röntgenabsorptionsspektroskopie angewendet. Dabei liefert die Untersuchung der Feinstruktur mittels der EXAFS-Spektroskopie (engl. Extended X-Ray Absorption Fine Structure) quantitative Informationen über die lokale Umgebung, während RIXS (engl. resonant inelastic X-ray scattering), sowie die daraus extrahierte hoch aufgelöste Nahkantenstruktur, XANES (engl. X-ray absorption near edge structure) qualitative Informationen über mögliche Koordinationsänderungen von La, Gd und Yb in den Gläsern liefert. Um mögliche Unterschiede der lokalen Struktur oberhalb der Glastransformationstemperatur (TG) zur Raumtemperatur zu untersuchen, wurden exemplarisch Hochtemperatur Y-EXAFS Untersuchungen durchgeführt.
Für die Auswertung der EXAFS-Messungen wurde ein neu eingeführter Histogramm-Fit verwendet, der auch nicht-symmetrische bzw. nichtgaußförmige Paarverteilungsfunktionen beschreiben kann, wie sie bei einem hohen Grad der Polymerisierung bzw. bei hohen Temperaturen auftreten können. Die Y-EXAFS-Spektren für die Prowatke und Klemme (2005) Zusammensetzungen zeigen mit Zunahme des ASI, eine Zunahme der Asymmetrie und Breite der Y-O Paarverteilungsfunktion, welche sich in sich in der Änderung der Koordinationszahl von 6 nach 8 und einer Zunahme des Y-O Abstand um 0.13Å manifestiert. Ein ähnlicher Trend lässt sich auch für die Gd- und Yb-EXAFS-Spektren beobachten. Die hoch aufgelösten XANESSpektren für La, Gd und Yb zeigen, dass sich die strukturellen Unterschiede zumindest halb-quantitativ bestimmen lassen. Dies gilt insbesondere für Änderungen im mittleren Abstand zu den Sauerstoffatomen. Im Vergleich zur EXAFS-Spektroskopie liefert XANES jedoch keine Informationen über die Form und Breite von Paarverteilungsfunktionen. Die Hochtemperatur EXAFS-Untersuchungen von Y zeigen Änderungen der lokalen Struktur oberhalb der Glasübergangstemperatur an, welche sich vordergründig auf eine thermisch induzierte Erhöhung des mittleren Y-O Abstandes zurückführen lassen. Allerdings zeigt ein Vergleich der Y-O Abstände für Zusammensetzungen mit einem ASI von 0.115 bzw. 0.755, ermittelt bei Raumtemperatur und TG, dass der im Glas beobachtete strukturelle Unterschied entlang der Zusammensetzungsserie in der Schmelze noch stärker ausfallen kann, als bisher für die Gläser angenommen wurde.
Die direkte Korrelation der Verteilungsdaten von Prowatke und Klemme (2005) mit den strukturellen Änderungen der Schmelzen offenbart für Y eine lineare Korrelation, wohingegen Yb und Gd eine nicht lineare Beziehung zeigen. Aufgrund seines Ionenradius und seiner Ladung wird das 6-fach koordinierte SEE in den niedriger polymerisierten Schmelzen bevorzugt durch nicht-brückenbildende Sauerstoffatome koordiniert, um stabile Konfigurationen zu bilden. In den höher polymerisierten Schmelzen mit ASI-Werten in der Nähe von 1 ist 6-fache Koordination nicht möglich, da fast nur noch brückenbildende Sauerstoffatome zur Verfügung stehen. Die Überbindung von brückenbildenden Sauerstoffatomen um das SEE wird durch Erhöhung der Koordinationszahl und des mittleren SEE-O Abstandes ausgeglichen. Dies bedeutet eine energetisch günstigere Konfiguration in den stärker depolymerisierten Zusammensetzungen, aus welcher die beobachtete Variation des Verteilungskoeffizienten resultiert, welcher sich jedoch für jedes Element stark unterscheidet. Für die haplogranitischen und haplobasaltischen Zusammensetzungen wurde mit Zunahme der Polymerisierung auch eine Zunahme der Koordinationszahl und des durchschnittlichen Bindungsabstands, einhergehend mit der Zunahme der Schiefe und der Asymmetrie der Paarverteilungsfunktion, beobachtet. Dies impliziert, dass das jeweilige SEE mit Zunahme der Polymerisierung auch inkompatibler in diesen Zusammensetzungen wird. Weiterhin zeigt die Zugabe von Wasser, dass die Schmelzen depolymerisieren, was in einer symmetrischeren Paarverteilungsfunktion resultiert, wodurch die Kompatibilität wieder zunimmt.
Zusammenfassend zeigt sich, dass die Veränderungen der Schmelzzusammensetzungen in einer Änderung der Polymerisierung der Schmelzen resultieren, die dann einen signifikanten Einfluss auf die lokale Umgebung der SEE hat. Die strukturellen Änderungen lassen sich direkt mit Verteilungsdaten korrelieren, die Trends unterscheiden sich aber stark zwischen leichten, mittleren und schweren SEE. Allerdings konnte diese Studie zeigen, in welcher Größenordnung die Änderungen liegen müssen, um einen signifikanten Einfluss auf den Verteilungskoeffizenten zu haben. Weiterhin zeigt sich, dass der Einfluss der Schmelzzusammensetzung auf die Verteilung der Spurenelemente mit Zunahme der Polymerisierung steigt und daher nicht vernachlässigt werden darf.
Im Graduiertenkolleg NatRiskChange der Universität Potsdam und anderen Forschungseinrichtungen werden beobachtete sowie zukünftig mögliche Veränderungen von Naturgefahren untersucht. Teil des strukturierten Doktorandenprogramms sind sogenannte Task-Force-Einsätze, bei denen die Promovierende zeitlich begrenzt ein aktuelles Ereignis auswerten. Im Zuge dieser Aktivität wurde die Sturzflut vom 29.05.2016 in Braunsbach (Baden-Württemberg) untersucht.
In diesem Bericht werden erste Auswertungen zur Einordnung der Niederschläge, zu den hydrologischen und geomorphologischen Prozessen im Einzugsgebiet des Orlacher Bachs sowie zu den verursachten Schäden beleuchtet.
Die Region war Zentrum extremer Regenfälle in der Größenordnung von 100 mm innerhalb von 2 Stunden. Das 6 km² kleine Einzugsgebiet hat eine sehr schnelle Reaktionszeit, zumal bei vorgesättigtem Boden. Im steilen Bachtal haben mehrere kleinere und größere Hangrutschungen über 8000 m³ Geröll, Schutt und Schwemmholz in das Gewässer eingetragen und möglicherweise kurzzeitige Aufstauungen und Durchbrüche verursacht. Neben den großen Wassermengen mit einer Abflussspitze in einer Größenordnung von 100 m³/s hat gerade die Geschiebefracht zu großen Schäden an den Gebäuden entlang des Bachlaufs in Braunsbach geführt.
Dynamics of mantle plumes
(2016)
Mantle plumes are a link between different scales in the Earth’s mantle: They are an important part of large-scale mantle convection, transporting material and heat from the core-mantle boundary to the surface, but also affect processes on a smaller scale, such as melt generation and transport and surface magmatism. When they reach the base of the lithosphere, they cause massive magmatism associated with the generation of large igneous provinces, and they can be related to mass extinction events (Wignall, 2001) and continental breakup (White and McKenzie, 1989).
Thus, mantle plumes have been the subject of many previous numerical modelling studies (e.g. Farnetani and Richards, 1995; d’Acremont et al., 2003; Lin and van Keken, 2005; Sobolev et al., 2011; Ballmer et al., 2013). However, complex mechanisms, such as the development and implications of chemical heterogeneities in plumes, their interaction with mid-ocean ridges and global mantle flow, and melt ascent from the source region to the surface are still not very well understood; and disagreements between observations and the predictions of classical plume models have led to a challenge of the plume concept in general (Czamanske et al., 1998; Anderson, 2000; Foulger, 2011). Hence, there is a need for more sophisticated models that can explain the underlying physics, assess which properties and processes are important, explain how they cause the observations visible at the Earth’s surface and provide a link between the different scales.
In this work, integrated plume models are developed that investigate the effect of dense recycled oceanic crust on the development of mantle plumes, plume–ridge interaction under the influence of global mantle flow and melting and melt migration in form of two-phase flow.
The presented analysis of these models leads to a new, updated picture of mantle plumes: Models considering a realistic depth-dependent density of recycled oceanic crust and peridotitic mantle material show that plumes with excess temperatures of up to 300 K can transport up to 15% of recycled oceanic crust through the whole mantle. However, due to the high density of recycled crust, plumes can only advance to the base of the lithosphere directly if they have high excess temperatures, high plume volumes and the lowermost mantle is subadiabatic, or plumes rise from the top or edges of thermo-chemical piles. They might only cause minor surface uplift, and instead of the classical head–tail structure, these low-buoyancy plumes are predicted to be broad features in the lower mantle with much less pronounced plume heads. They can form a variety of shapes and regimes, including primary plumes directly advancing to the base of the lithosphere, stagnating plumes, secondary plumes rising from the core–mantle boundary or a pool of eclogitic material in the upper mantle and failing plumes. In the upper mantle, plumes are tilted and deflected by global mantle flow, and the shape, size and stability of the melting region is influenced by the distance from nearby plate boundaries, the speed of the overlying plate and the movement of the plume tail arriving from the lower mantle. Furthermore, the structure of the lithosphere controls where hot material is accumulated and melt is generated. In addition to melting in the plume tail at the plume arrival position, hot plume material flows upwards towards opening rifts, towards mid-ocean ridges and towards other regions of thinner lithosphere, where it produces additional melt due to decompression. This leads to the generation of either broad ridges of thickened magmatic crust or the separation into multiple thinner lines of sea mount chains at the surface. Once melt is generated within the plume, it influences its dynamics, lowering the viscosity and density, and while it rises the melt volume is increased up to 20% due to decompression. Melt has the tendency to accumulate at the top of the plume head, forming diapirs and initiating small-scale convection when the plume reaches the base of the lithosphere. Together with the introduced unstable, high-density material produced by freezing of melt, this provides an efficient mechanism to thin the lithosphere above plume heads.
In summary, this thesis shows that mantle plumes are more complex than previously considered, and linking the scales and coupling the physics of different processes occurring in mantle plumes can provide insights into how mantle plumes are influenced by chemical heterogeneities, interact with the lithosphere and global mantle flow, and are affected by melting and melt migration. Including these complexities in geodynamic models shows that plumes can also have broad plume tails, might produce only negligible surface uplift, can generate one or several volcanic island chains in interaction with a mid–ocean ridge, and can magmatically thin the lithosphere.
Earthquakes deform Earth's surface, building long-lasting topographic features and contributing to landscape and mountain formation.
However, seismic waves produced by earthquakes may also destabilize hillslopes, leading to large amounts of soil and bedrock moving downslope. Moreover, static deformation and shaking are suspected to damage the surface bedrock and therefore alter its future properties, affecting hydrological and erosional dynamics. Thus, earthquakes participate both in mountain building and stimulate directly or indirectly their erosion. Moreover, the impact of earthquakes on hillslopes has important implications for the amount of sediment and organic matter delivered to rivers, and ultimately to oceans, during episodic catastrophic seismic crises, the magnitude of life and property losses associated with landsliding, the perturbation and recovery of landscape properties after shaking, and the long term topographic evolution of mountain belts. Several of these aspects have been addressed recently through individual case studies but additional data compilation as well as theoretical or numerical modelling are required to tackle these issues in a more systematic and rigorous manner.
This dissertation combines data compilation of earthquake characteristics, landslide mapping, and seismological data interpretation with physically-based modeling in order to address how earthquakes impact on erosional processes and landscape evolution. Over short time scales (10-100 s) and intermediate length scales (10 km), I have attempted to improve our understanding and ability to predict the amount of landslide debris triggered by seismic shaking in epicentral areas. Over long time scales (1-100 ky) and across a mountain belt (100 km) I have modeled the competition between erosional unloading and building of topography associated with earthquakes. Finally, over intermediate time scales (1-10 y) and at the hillslope scale (0.1-1 km) I have collected geomorphological and seismological data that highlight persistent effects of earthquakes on landscape properties and behaviour.
First, I compiled a database on earthquakes that produced significant landsliding, including an estimate of the total landslide volume and area, and earthquake characteristics such as seismic moment and source depth. A key issue is the accurate conversion of landslide maps into volume estimates. Therefore I also estimated how amalgamation - when mapping errors lead to the bundling of multiple landslide into a single polygon - affects volume estimates from various earthquake-induced landslide inventories and developed an algorithm to automatically detect this artifact. The database was used to test a physically-based prediction of the total landslide area and volume caused by earthquakes, based on seismological scaling relationships and a statistical description of the landscape properties. The model outperforms empirical fits in accuracy, with 25 out of 40 cases well predicted, and allows interpretation of many outliers in physical terms. Apart from seismological complexities neglected by the model I found that exceptional rock strength properties or antecedent conditions may explain most outliers.
Second, I assessed the geomorphic effects of large earthquakes on landscape dynamics by surveying the temporal evolution of precipitation-normalized landslide rate. I found strongly elevated landslide rates following earthquakes that progressively recover over 1 to 4 years, indicating that regolith strength drops and recovers. The relaxation is clearly non-linear for at least one case, and does not seem to correlate with coseismic landslide reactivation, water table level increase or tree root-system recovery. I suggested that shallow bedrock is damaged by the earthquake and then heals on annual timescales. Such variations in ground strength must be translated into shallow subsurface seismic velocities that are increasingly surveyed with ambient seismic noise correlations. With seismic noise autocorrelation I computed the seismic velocity in the epicentral areas of three earthquakes where I constrained a change in landslide rate. We found similar recovery dynamics and timescales, suggesting that seismic noise correlation techniques could be further developed to meaningfully assess ground strength variations for landscape dynamics. These two measurements are also in good agreement with the temporal dynamics of post-seismic surface displacement measured by GPS. This correlation suggests that the surface healing mechanism may be driven by tectonic deformation, and that the surface regolith and fractured bedrock may behave as a granular media that slowly compacts as it is sheared or vibrated.
Last, I compared our model of earthquake-induced landsliding with a standard formulation of surface deformation caused by earthquakes to understand which parameters govern the competition between the building and destruction of topography caused by earthquakes. In contrast with previous studies I found that very large (Mw>8) earthquakes always increase the average topography, whereas only intermediate (Mw ~ 7) earthquakes in steep landscapes may reduce topography. Moreover, I illustrated how the net effect of earthquakes varies with depth or landscape steepness implying a complex and ambivalent role through the life of a mountain belt. Further I showed that faults producing a Gutenberg-Richter distribution of earthquake sizes, will limit topography over a larger range of fault sizes than faults producing repeated earthquakes with a characteristic size.
Effects of data and model simplification on the results of a wetland water resource management model
(2016)
This paper presents the development of a wetland water balance model for use in a large river basin with many different wetlands. The basic model was primarily developed for a single wetland with a complex water management system involving large amounts of specialized input data and water management details. The aim was to simplify the model structure and to use only commonly available data as input for the model, with the least possible loss of accuracy. Results from different variants of the model and data adaptation were tested against results from a detailed model. This shows that using commonly available data and unifying and simplifying the input data is tolerable up to a certain level. The simplification of the model has greater effects on the evaluated water balance components than the data adaptation. Because this simplification was necessary for large-scale use, we suggest that, for reasons of comparability, simpler models should always be applied with uniform data bases for large regions, though these should only be moderately simplified. Further, we recommend using these simplified models only for large-scale comparisons and using more specific, detailed models for investigations on smaller scales.
We present new experimental data of the low-temperature metastable region of liquid water derived from high-density synthetic fluid inclusions (996–916 kg m−3) in quartz. Microthermometric measurements include: (i) prograde (upon heating) and retrograde (upon cooling) liquid–vapour homogenisation. We used single ultrashort laser pulses to stimulate vapour bubble nucleation in initially monophase liquid inclusions. Water densities were calculated based on prograde homogenisation temperatures using the IAPWS-95 formulation. We found retrograde liquid–vapour homogenisation temperatures in excellent agreement with IAPWS-95. (ii) Retrograde ice nucleation. Raman spectroscopy was used to determine the nucleation of ice in the absence of the vapour bubble. Our ice nucleation data in the doubly metastable region are inconsistent with the low-temperature trend of the spinodal predicted by IAPWS-95, as liquid water with a density of 921 kg m−3 remains in a homogeneous state during cooling down to a temperature of −30.5 °C, where it is transformed into ice whose density corresponds to zero pressure. (iii) Ice melting. Ice melting temperatures of up to 6.8 °C were measured in the absence of the vapour bubble, i.e. in the negative pressure region. (iv) Spontaneous retrograde and, for the first time, prograde vapour bubble nucleation. Prograde bubble nucleation occurred upon heating at temperatures above ice melting. The occurrence of prograde and retrograde vapour bubble nucleation in the same inclusions indicates a maximum of the bubble nucleation curve in the ϱ–T plane at around 40 °C. The new experimental data represent valuable benchmarks to evaluate and further improve theoretical models describing the p–V–T properties of metastable water in the low-temperature region.
Lake Towuti is a tectonic basin, surrounded by ultramafic rocks. Lateritic soils form through weathering and deliver abundant iron (oxy)hydroxides but very little sulfate to the lake and its sediment. To characterize the sediment biogeochemistry, we collected cores at three sites with increasing water depth and decreasing bottom water oxygen concentrations. Microbial cell densities were highest at the shallow site a feature we attribute to the availability of labile organic matter (OM) and the higher abundance of electron acceptors due to oxic bottom water conditions. At the two other sites, OM degradation and reduction processes below the oxycline led to partial electron acceptor depletion. Genetic information preserved in the sediment as extracellular DNA (eDNA) provided information on aerobic and anaerobic heterotrophs related to Nitrospirae. Chloroflexi, and Therrnoplasmatales. These taxa apparently played a significant role in the degradation of sinking OM. However, eDNA concentrations rapidly decreased with core depth. Despite very low sulfate concentrations, sulfate-reducing bacteria were present and viable in sediments at all three sites, as confirmed by measurement of potential sulfate reduction rates. Microbial community fingerprinting supported the presence of taxa related to Deltaproteobacteria and Firmicutes with demonstrated capacity for iron and sulfate reduction. Concomitantly, sequences of Ruminococcaceae, Clostridiales, and Methanornicrobiales indicated potential for fermentative hydrogen and methane production. Such first insights into ferruginous sediments showed that microbial populations perform successive metabolisms related to sulfur, iron, and methane. In theory, iron reduction could reoxidize reduced sulfur compounds and desorb OM from iron minerals to allow remineralization to methane. Overall, we found that biogeochemical processes in the sediments can be linked to redox differences in the bottom waters of the three sites, like oxidant concentrations and the supply of labile OM. At the scale of the lacustrine record, our geomicrobiological study should provide a means to link the extant subsurface biosphere to past environments.
Understanding the role of natural climate variability under the pressure of human induced changes of climate and landscapes, is crucial to improve future projections and adaption strategies. This doctoral thesis aims to reconstruct Holocene climate and environmental changes in NE Germany based on annually laminated lake sediments. The work contributes to the ICLEA project (Integrated CLimate and Landscape Evolution Analyses). ICLEA intends to compare multiple high-resolution proxy records with independent chronologies from the N central European lowlands, in order to disentangle the impact of climate change and human land use on landscape development during the Lateglacial and Holocene. In this respect, two study sites in NE Germany are investigated in this doctoral project, Lake Tiefer See and palaeolake Wukenfurche. While both sediment records are studied with a combination of high-resolution sediment microfacies and geochemical analyses (e.g. µ-XRF, carbon geochemistry and stable isotopes), detailed proxy understanding mainly focused on the continuous 7.7 m long sediment core from Lake Tiefer See covering the last ~6000 years. Three main objectives are pursued at Lake Tiefer See: (1) to perform a reliable and independent chronology, (2) to establish microfacies and geochemical proxies as indicators for climate and environmental changes, and (3) to trace the effects of climate variability and human activity on sediment deposition.
Addressing the first aim, a reliable chronology of Lake Tiefer See is compiled by using a multiple-dating concept. Varve counting and tephra findings form the chronological framework for the last ~6000 years. The good agreement with independent radiocarbon dates of terrestrial plant remains verifies the robustness of the age model. The resulting reliable and independent chronology of Lake Tiefer See and, additionally, the identification of nine tephras provide a valuable base for detailed comparison and synchronization of the Lake Tiefer See data set with other climate records. The sediment profile of Lake Tiefer See exhibits striking alternations between well-varved and non-varved sediment intervals. The combination of microfacies, geochemical and microfossil (i.e. Cladocera and diatom) analyses indicates that these changes of varve preservation are caused by variations of lake circulation in Lake Tiefer See. An exception is the well-varved sediment deposited since AD 1924, which is mainly influenced by human-induced lake eutrophication. Well-varved intervals before the 20th century are considered to reflect phases of reduced lake circulation and, consequently, stronger anoxic conditions. Instead, non-varved intervals indicate increased lake circulation in Lake Tiefer See, leading to more oxygenated conditions at the lake ground. Furthermore, lake circulation is not only influencing sediment deposition, but also geochemical processes in the lake. As, for example, the proxy meaning of δ13COM varies in time in response to changes of the oxygen regime in the lake hypolinion. During reduced lake circulation and stronger anoxic conditions δ13COM is influenced by microbial carbon cycling. In contrast, organic matter degradation controls δ13COM during phases of intensified lake circulation and more oxygenated conditions. The varve preservation indicates an increasing trend of lake circulation at Lake Tiefer See after ~4000 cal a BP. This trend is superimposed by decadal to centennial scale variability of lake circulation intensity. Comparison to other records in Central Europe suggests that the long-term trend is probably related to gradual changes in Northern Hemisphere orbital forcing, which induced colder and windier conditions in Central Europe and, therefore, reinforced lake circulation. Decadal to centennial scale periods of increased lake circulation coincide with settlement phases at Lake Tiefer See, as inferred from pollen data of the same sediment record. Deforestation reduced the wind shelter of the lake, which probably increased the sensitivity of lake circulation to wind stress. However, results of this thesis also suggest that several of these phases of increased lake circulation are additionally reinforced by climate changes. A first indication is provided by the comparison to the Baltic Sea record, which shows striking correspondence between major non-varved intervals at Lake Tiefer See and bioturbated sediments in the Baltic Sea. Furthermore, a preliminary comparison to the ICLEA study site Lake Czechowskie (N central Poland) shows a coincidence of at least three phases of increased lake circulation in both lakes, which concur with periods of known climate changes (2.8 ka event, ’Migration Period’ and ’Little Ice Age’). These results suggest an additional over-regional climate forcing also on short term increased of lake circulation in Lake Tiefer See.
In summary, the results of this thesis suggest that lake circulation at Lake Tiefer See is driven by a combination of long-term and short-term climate changes as well as of anthropogenic deforestation phases. Furthermore, the lake circulation drives geochemical cycles in the lake affecting the meaning of proxy data. Therefore, the work presented here expands the knowledge of climate and environmental variability in NE Germany. Furthermore, the integration of the Lake Tiefer See multi-proxy record in a regional comparison with another ICLEA side, Lake Czechowskie, enabled to better decipher climate changes and human impact on the lake system. These first results suggest a huge potential for further detailed regional comparisons to better understand palaeoclimate dynamics in N central Europe.
The lakes in the Kenyan Rift Valley offer the unique opportunity to study a wide range of hydrochemical environmental conditions, ranging from freshwater to highly saline and alkaline lakes. Because little is known about the hydro- and biogeochemical conditions in the underlying lake sediments, it was the aim of this study to extend the already existing data sets with data from porewater and biomarker analyses. Additionally, reduced sulphur compounds and sulphate reduction rates in the sediment were determined. The new data was used to examine the anthropogenic and microbial influence on the lakes sediments as well as the influence of the water chemistry on the degradation and preservation of organic matter in the sediment column. The lakes discussed in this study are: Logipi, Eight (a small crater lake in the region of Kangirinyang), Baringo, Bogoria, Naivasha, Oloiden, and Sonachi.
The biomarker compositions were similar in all studied lake sediments; nevertheless, there were some differences between the saline and freshwater lakes. One of those differences is the occurrence of a molecule related to β-carotene, which was only found in the saline lakes. This molecule most likely originates from cyanobacteria, single-celled organisms which are commonly found in saline lakes. In the two freshwater lakes, stigmasterol, a sterol characteristic for freshwater algae, was found. In this study, it was shown that Lakes Bogoria and Sonachi can be used for environmental reconstructions with biomarkers, because the absence of oxygen at the lake bottoms slowed the degradation process. Other lakes, like for example Lake Naivasha, cannot be used for such reconstructions, because of the large anthropogenic influence. But the biomarkers proved to be a useful tool to study those anthropogenic influences. Additionally, it was observed that horizons with a high concentration of elemental sulphur can be used as temporal markers. Those horizons were deposited during times when the lake levels were very low. The sulphur was deposited by microorganisms which are capable of anoxygenic photosynthesis or sulphide oxidation.
Subsurface microbial communities undertake many terminal electron-accepting processes, often simultaneously. Using a tritium-based assay, we measured the potential hydrogen oxidation catalyzed by hydrogenase enzymes in several subsurface sedimentary environments (Lake Van, Barents Sea, Equatorial Pacific, and Gulf of Mexico) with different predominant electron-acceptors. Hydrogenases constitute a diverse family of enzymes expressed by microorganisms that utilize molecular hydrogen as a metabolic substrate, product, or intermediate. The assay reveals the potential for utilizing molecular hydrogen and allows qualitative detection of microbial activity irrespective of the predominant electron-accepting process. Because the method only requires samples frozen immediately after recovery, the assay can be used for identifying microbial activity in subsurface ecosystems without the need to preserve live material. We measured potential hydrogen oxidation rates in all samples from multiple depths at several sites that collectively span a wide range of environmental conditions and biogeochemical zones. Potential activity normalized to total cell abundance ranges over five orders of magnitude and varies, dependent upon the predominant terminal electron acceptor. Lowest per-cell potential rates characterize the zone of nitrate reduction and highest per-cell potential rates occur in the methanogenic zone. Possible reasons for this relationship to predominant electron acceptor include (i) increasing importance of fermentation in successively deeper biogeochemical zones and (ii) adaptation of H(2)ases to successively higher concentrations of H-2 in successively deeper zones.
Precision horticulture encompasses site- or tree-specific management in fruit plantations. Of decisive importance is spatially resolved data (this means data from each tree) from the production site, since it may enable customized and, therefore, resource-efficient production measures.
The present thesis involves an examination of the apparent electrical conductivity of the soil (ECa), the plant water status spatially measured by means of the crop water stress index (CWSI), and the fruit quality (e.g. fruit size) for Prunus domestica L. (plums) and Citrus x aurantium, Syn. Citrus paradisi (grapefruit). The goals of the present work were i) characterization of the 3D distribution of the apparent electrical conductivity of the soil and variability of the plant’s water status; ii) investigation of the interaction between ECa, CWSI, and fruit quality; and iii) an approach for delineating management zones with respect to managing trees individually.
To that end, the main investigations took place in the plum orchard. This plantation got a slope of 3° grade on Pleistocene and post-Pleistocene substrates in a semi-humid climate (Potsdam, Germany) and encloses an area of 0.37 ha with 156 trees of the cultivar ˈTophit Plusˈ on a Wavit rootstock. The plantation was laid in 2009 with annual and biannual trees spaced 4 m distance along the irrigation system and 5 m between the rows. The trees were watered three times a week with a drip irrigation system positioned 50 cm above ground level providing 1.6 l per tree per event. With the help of geoelectric measurements, the apparent electrical conductivity of the upper soil (0.25 m) was measured for each tree with an electrode spacing of 0.5 m (4-point light hp). In this manner, the plantation was spatially charted with respect to the soil’s ECa. Additionally, tomography measurements were performed for 3D mapping of the soil ECa and spot checks of drilled cores with a profile of up to 1 m. The vegetative, generative, and fruit quality data were collected for each tree. The instantaneous plant water status was comprehensively determined in spot checks with the established Scholander method for water potential analysis (Scholander pressure bomb) as well as thermal imaging. An infrared camera was used for the thermal imaging (ThermaCam SC 500), mounted on a tractor 3.3 m above ground level. The thermal images (320 x 240 px) of the canopy surface were taken with an aperture of 45° and a geometric resolution of 8.54 x 6.41 mm. With the aid of the canopy temperature readings from the thermal images, cross-checked with manual temperature measurements of a dry and a wet reference leaf, the crop water stress index (CWSI) was calculated. Adjustments in CWSI for measurements in a semi-humid climate were developed, whereas the collection of reference temperatures was automatically collected from thermal images.
The bonitur data were transformed with the help of a variance stabilization process into a normal distribution. The statistical analyses as well as the automatic evaluation routine were performed with several scripts in MATLAB® (R2010b and R2016a) and a free program (spatialtoolbox). The hot spot analysis served to check whether an observed pattern is statistically significant. The method was evaluated with an established k-mean analysis. To test the hot-spot analysis by comparison, data from a grapefruit plantation (Adana, Turkey) was collected, including soil ECa, trunk circumference, and yield data. The plantation had 179 trees on a soil of type Xerofkuvent with clay and clay-loamy texture. The examination of the interaction between the critical values from the soil and plant water status information and the vegetative and generative plant growth variables was performed with the application from ANOVA.
The study indicates that the variability of the soil and plant information in fruit production is high, even considering small orchards. It was further indicated that the spatial patterns found in the soil ECa stayed constant through the years (r = 0.88 in 2011-2012 and r = 0.71 in 2012-2013). It was also demonstrated that CWSI determination may also be possible in semi-humid climate. A correlation (r = - 0.65, p < 0.0001) with the established method of leaf water potential analysis was found. The interaction between the ECa from various depths and the plant variables produced a highly significant connection with the topsoil in which the irrigation system was to be found. A correlation between yield and ECatopsoil of r = 0.52 was determined. By using the hot-spot analysis, extreme values in the spatial data could be determined. These extremes served to divide the zones (cold-spot, random, hot-spot). The random zone showed the highest correlation to the plant variables.
In summary it may be said that the cumulative water use efficiency (WUEc) was enhanced with high crop load. While the CWSI had no effect on fruit quality, the interaction of CWSI and WUEc even outweighed the impact of soil ECa on fruit quality in the production system with irrigation. In the plum orchard, irrigation was relevant for obtaining high quality produce even in the semi-humid climate.
Intermontane valley fills
(2016)
Sedimentary valley fills are a widespread characteristic of mountain belts around the world. They transiently store material over time spans ranging from thousands to millions of years and therefore play an important role in modulating the sediment flux from the orogen to the foreland and to oceanic depocenters. In most cases, their formation can be attributed to specific fluvial conditions, which are closely related to climatic and tectonic processes. Hence, valley-fill deposits constitute valuable archives that offer fundamental insight into landscape evolution, and their study may help to assess the impact of future climate change on sediment dynamics.
In this thesis I analyzed intermontane valley-fill deposits to constrain different aspects of the climatic and tectonic history of mountain belts over multiple timescales. First, I developed a method to estimate the thickness distribution of valley fills using artificial neural networks (ANNs). Based on the assumption of geometrical similarity between exposed and buried parts of the landscape, this novel and highly automated technique allows reconstructing fill thickness and bedrock topography on the scale of catchments to entire mountain belts.
Second, I used the new method for estimating the spatial distribution of post-glacial sediments that are stored in the entire European Alps. A comparison with data from exploratory drillings and from geophysical surveys revealed that the model reproduces the measurements with a root mean squared error (RMSE) of 70m and a coefficient of determination (R2) of 0.81. I used the derived sediment thickness estimates in combination with a model of the Last Glacial Maximum (LGM) icecap to infer the lithospheric response to deglaciation, erosion and deposition, and deduce their relative contribution to the present-day rock-uplift rate. For a range of different lithospheric and upper mantle-material properties, the results suggest that the long-wavelength uplift signal can be explained by glacial isostatic adjustment with a small erosional contribution and a substantial but localized tectonic component exceeding 50% in parts of the Eastern Alps and in the Swiss Rhône Valley. Furthermore, this study reveals the particular importance of deconvolving the potential components of rock uplift when interpreting recent movements along active orogens and how this can be used to constrain physical properties of the Earth’s interior.
In a third study, I used the ANN approach to estimate the sediment thickness of alluviated reaches of the Yarlung Tsangpo River, upstream of the rapidly uplifting Namche Barwa massif. This allowed my colleagues and me to reconstruct the ancient river profile of the Yarlung Tsangpo, and to show that in the past, the river had already been deeply incised into the eastern margin of the Tibetan Plateau. Dating of basal sediments from drill cores that reached the paleo-river bed to 2–2.5 Ma are consistent with mineral cooling ages from the Namche Barwa massif, which indicate initiation of rapid uplift at ~4 Ma. Hence, formation of the Tsangpo gorge and aggradation of the voluminous valley fill was most probably a consequence of rapid uplift of the Namche Barwa massif and thus tectonic activity.
The fourth and last study focuses on the interaction of fluvial and glacial processes at the southeastern edge of the Karakoram. Paleo-ice-extent indicators and remnants of a more than 400-m-thick fluvio-lacustrine valley fill point to blockage of the Shyok River, a main tributary of the upper Indus, by the Siachen Glacier, which is the largest glacier in the Karakoram Range. Field observations and 10Be exposure dating attest to a period of recurring lake formation and outburst flooding during the penultimate glaciation prior to ~110 ka. The interaction of Rivers and Glaciers all along the Karakorum is considered a key factor in landscape evolution and presumably promoted headward erosion of the Indus-Shyok drainage system into the western margin of the Tibetan Plateau.
The results of this thesis highlight the strong influence of glaciation and tectonics on valley-fill formation and how this has affected the evolution of different mountain belts. In the Alps valley-fill deposition influenced the magnitude and pattern of rock uplift since ice retreat approximately 17,000 years ago. Conversely, the analyzed valley fills in the Himalaya are much older and reflect environmental conditions that prevailed at ~110 ka and ~2.5 Ma, respectively. Thus, the newly developed method has proven useful for inferring the role of sedimentary valley-fill deposits in landscape evolution on timescales ranging from 1,000 to 10,000,000 years.
Observed recent and expected future increases in frequency and intensity of climatic extremes in central Europe may pose critical challenges for domestic tree species. Continuous dendrometer recordings provide a valuable source of information on tree stem radius variations, offering the possibility to study a tree's response to environmental influences at a high temporal resolution. In this study, we analyze stem radius variations (SRV) of three domestic tree species (beech, oak, and pine) from 2012 to 2014. We use the novel statistical approach of event coincidence analysis (ECA) to investigate the simultaneous occurrence of extreme daily weather conditions and extreme SRVs, where extremes are defined with respect to the common values at a given phase of the annual growth period. Besides defining extreme events based on individual meteorological variables, we additionally introduce conditional and joint ECA as new multivariate extensions of the original methodology and apply them for testing 105 different combinations of variables regarding their impact on SRV extremes. Our results reveal a strong susceptibility of all three species to the extremes of several meteorological variables. Yet, the inter-species differences regarding their response to the meteorological extremes are comparatively low. The obtained results provide a thorough extension of previous correlation-based studies by emphasizing on the timings of climatic extremes only. We suggest that the employed methodological approach should be further promoted in forest research regarding the investigation of tree responses to changing environmental conditions.
The increase in atmospheric methane concentration, which is determined by an imbalance between its sources and sinks, has led to investigations of the methane cycle in various environments. Aquatic environments are of an exceptional interest due to their active involvement in methane cycling worldwide and in particular in areas sensitive to climate change. Furthermore, being connected with each other aquatic environments form networks that can be spread on vast areas involving marine, freshwater and terrestrial ecosystems. Thus, aquatic systems have a high potential to translate local or regional environmental and subsequently ecosystem changes to a bigger scale. Many studies neglect this connectivity and focus on individual aquatic or terrestrial ecosystems.
The current study focuses on environmental controls of the distribution and aerobic oxidation of methane at the example of two aquatic ecosystems. These ecosystems are Arctic fresh water bodies and the Elbe estuary which represent interfaces between freshwater-terrestrial and freshwater-marine environments, respectively.
Arctic water bodies are significant atmospheric sources of methane. At the same time the methane cycle in Arctic water bodies is strongly affected by the surrounding permafrost environment, which is characterized by high amounts of organic carbon. The results of this thesis indicate that the methane concentrations in Arctic lakes and streams substantially vary between each other being regulated by local landscape features (e.g. floodplain area) and the morphology of the water bodies (lakes, streams and river). The highest methane concentrations were detected in the lake outlets and in a floodplain lake complex. In contrast, the methane concentrations measured at different sites of the Lena River did not vary substantially. The lake complexes in comparison to the Lena River, thus, appear as more individual and heterogeneous systems with a pronounced imprint of the surrounding soil environment. Furthermore, connected with each other Arctic aquatic environments have a large potential to transport methane from methane-rich water bodies such as streams and floodplain lakes to aquatic environments relatively poor in methane such as the Lena River.
Estuaries represent hot spots of oceanic methane emissions. Also, estuaries are intermediate zones between methane-rich river water and methane depleted marine water. Substantiated through this thesis at the example of the Elbe estuary, the methane distribution in estuaries, however, cannot entirely be described by the conservative mixing model i.e. gradual decrease from the freshwater end-member to the marine water end-member. In addition to the methane-rich water from the Elbe River mouth substantial methane input occurs from tidal flats, areas of significant interaction between aquatic and terrestrial environments. Thus, this study demonstrates the complex interactions and their consequences for the methane distribution within estuaries. Also it reveals how important it is to investigate estuaries at larger spatial scales.
Methane oxidation (MOX) rates are commonly correlated with methane concentrations. This was shown in previous research studies and was substantiated by the present thesis. In detail, the highest MOX rates in the Arctic water bodies were detected in methane-rich streams and in the floodplain area while in the Elbe estuary the highest MOX rates were observed at the coastal stations. However, in these bordering environments, MOX rates are affected not only via the regulation through methane concentrations. The MOX rates in the Arctic lakes were shown to be also dependent on the abundance and community composition of methane-oxidising bacteria (MOB), that in turn are controlled by local landscape features (regardless of the methane concentrations) and by the transport of MOB between neighbouring environments. In the Elbe estuary, the MOX rates in addition to the methane concentrations are largely affected by the salinity, which is in turn regulated by the mixing of fresh- and marine waters. The magnitude of the salinity impact on MOX rates thereby depends on the MOB community composition and on the rate of the salinity change.
This study extends our knowledge of environmental controls of methane distribution and aerobic methane oxidation in aquatic environments. It also illustrates how important it is to investigate complex ecosystems rather than individual ecosystems to better understand the functioning of whole biomes.
Die Elbe und ihr Einzugsgebiet sind vom Klimawandel betroffen. Um die Wirkkette von projizierten Klimaveränderungen auf den Wasserhaushalt und die daraus resultierenden Nährstoffeinträge und -frachten für große Einzugsgebiete wie das der Elbe zu analysieren, können integrierte Umweltmodellsysteme eingesetzt werden. Fallstudien, die mit diesen Modellsystemen ad hoc durchgeführt werden, repräsentieren den Istzustand von Modellentwicklungen und -unsicherheiten und sind damit statisch.
Diese Arbeit beschreibt den Einstieg in die Dynamisierung von Klimafolgenanalysen im Elbegebiet. Dies umfasst zum einen eine Plausibilitätsprüfung von Auswirkungsrechnungen, die mit Szenarien des statistischen Szenariengenerators STARS durchgeführt wurden, durch den Vergleich mit den Auswirkungen neuerer Klimaszenarien aus dem ISI-MIP Projekt, die dem letzten Stand der Klimamodellierung entsprechen. Hierfür wird ein integriertes Modellsystem mit "eingefrorenem Entwicklungsstand" verwendet. Die Klimawirkungsmodelle bleiben dabei unverändert. Zum anderen wird ein Bestandteil des integrierten Modellsystems – das ökohydrologische Modell SWIM – zu einer "live"-Version weiterentwickelt. Diese wird durch punktuelle Testung an langjährigen Versuchsreihen eines Lysimeterstandorts sowie an aktuellen Abflussreihen validiert und verbessert.
Folgende Forschungsfragen werden bearbeitet: (i) Welche Effekte haben unterschiedliche Klimaszenarien auf den Wasserhaushalt im Elbegebiet und ist eine Neubewertung der Auswirkung des Klimawandels auf den Wasserhaushalt notwendig?, (ii) Was sind die Auswirkungen des Klimawandels auf die Nährstoffeinträge und -frachten im Elbegebiet sowie die Wirksamkeit von Maßnahmen zur Reduktion der Nährstoffeinträge?, (iii) Ist unter der Nutzung (selbst einer sehr geringen Anzahl) verfügbarer tagesaktueller Witterungsdaten in einem stark heterogenen Einzugsgebiet eine valide Ansprache der aktuellen ökohydrologischen Situation des Elbeeinzugsgebiets möglich?
Die aktuellen Szenarien bestätigen die Richtung, jedoch nicht das Ausmaß der Klimafolgen: Die Rückgänge des mittleren jährlichen Gesamtabflusses und der monatlichen Abflüsse an den Pegeln bis Mitte des Jahrhunderts betragen für das STARS-Szenario ca. 30 %. Die Rückgänge bei den auf dem ISI-MIP-Szenario basierenden Modellstudien liegen hingegen nur bei ca. 10 %. Hauptursachen für diese Divergenz sind die Unterschiede in den Niederschlagsprojektionen sowie die Unterschiede in der jahreszeitlichen Verteilung der Erwärmung. Im STARS-Szenario gehen methodisch bedingt die Niederschläge zurück und der Winter erwärmt sich stärker als der Sommer. In dem ISI-MIP-Szenario bleiben die Niederschläge nahezu stabil und die Erwärmung im Sommer und Winter unterscheidet sich nur geringfügig.
Generell nehmen die Nährstoffeinträge und -frachten mit den Abflüssen in beiden Szenarien unterproportional ab, wobei die Frachten jeweils stärker als die Einträge zurückgehen. Die konkreten Effekte der Abflussänderungen sind gering und liegen im einstelligen Prozentbereich. Gleiches gilt für die Unterschiede zwischen den Szenarien. Der Effekt von zwei ausgewählten Maßnahmen zur Reduktion der Nährstoffeinträge und -frachten unterscheidet sich bei verschiedenen Abflussverhältnissen, repräsentiert durch unterschiedliche Klimaszenarien in unterschiedlich feuchter Ausprägung, ebenfalls nur geringfügig.
Die Beantwortung der ersten beiden Forschungsfragen zeigt, dass die Aktualisierung von Klimaszenarien in einem ansonsten "eingefrorenen" Verbund von ökohydrologischen Daten und Modellen eine wichtige Prüfoption für die Plausibilisierung von Klimafolgenanalysen darstellt. Sie bildet die methodische Grundlage für die Schlussfolgerung, dass bei der Wassermenge eine Neubewertung der Klimafolgen notwendig ist, während dies bei den Nährstoffeinträgen und -frachten nicht der Fall ist.
Die zur Beantwortung der dritten Forschungsfrage mit SWIM-live durchgeführten Validierungsstudien ergeben Diskrepanzen am Lysimeterstandort und bei den Abflüssen aus den Teilgebieten Saale und Spree. Sie lassen sich zum Teil mit der notwendigen Interpolationsweite der Witterungsdaten und dem Einfluss von Wasserbewirtschaftungsmaßnahmen erklären. Insgesamt zeigen die Validierungsergebnisse, dass schon die Pilotversion von SWIM-live für eine ökohydrologische Ansprache des Gebietswasserhaushaltes im Elbeeinzugsgebiet genutzt werden kann. SWIM-live ermöglicht eine unmittelbare Betrachtung und Beurteilung simulierter Daten. Dadurch werden Unsicherheiten bei der Modellierung direkt offengelegt und können infolge dessen reduziert werden. Zum einen führte die Verdichtung der meteorologischen Eingangsdaten durch die Verwendung von nun ca. 700 anstatt 19 Klima- bzw. Niederschlagstationen zu einer Verbesserung der Ergebnisse. Zum anderen wurde SWIM-live beispielhaft für einen Zyklus aus punktueller Modellverbesserung und flächiger Überprüfung der Simulationsergebnisse genutzt.
Die einzelnen Teilarbeiten tragen jeweils zur Dynamisierung von Klimafolgenanalysen im Elbegebiet bei. Der Anlass hierfür war durch die fehlerhaften methodischen Grundlagen von STARS gegeben. Die Sinnfälligkeit der Dynamisierung ist jedoch nicht an diesen konkreten Anlass gebunden, sondern beruht auf der grundlegenden Einsicht, dass Ad-hoc-Szenarienanalysen immer auch pragmatische Vereinfachungen zugrunde liegen, die fortlaufend überprüft werden müssen.