Refine
Has Fulltext
- no (4)
Year of publication
- 2011 (4) (remove)
Document Type
- Article (4)
Language
- English (4)
Is part of the Bibliography
- yes (4)
Institute
Cavitation at the solid surface normally begins with nucleation, in which defects or assembled molecules located at a liquid-solid interface act as nucleation centers and are actively involved in the evolution of cavitation bubbles. Here, we propose a simple approach to evaluate the behavior of cavitation bubbles formed under high intensity ultrasound (20 kHz, 51.3 W cm (2)) at solid surfaces, based on sonication of patterned substrates with a small roughness (less than 3 nm) and controllable surface energy. A mixture of octadecylphosphonic acid (ODTA) and octadecanethiol (ODT) was stamped on the Si wafer coated with different thicknesses of an aluminium layer (20-500 nm). We investigated the growth mechanism of cavitation bubble nuclei and the evolution of individual pits (defects) formed under sonication on the modified surface. A new activation behavior as a function of Al thickness, sonication time, ultrasonic power and temperature is reported. In this process cooperativity is introduced, as initially formed pits further reduce the energy to form bubbles. Furthermore, cavitation on the patterns is a controllable process, where up to 40-50 min of sonication time only the hydrophobic areas are active nucleation sites. This study provides a convincing proof of our theoretical approach on nucleation.
We report on the interaction of cationic azobenzene-containing surfactant with DNA investigated by absorption and fluorescence spectroscopy, dynamic light scattering, and atomic force microscopy. The properties of the surfactant can be controlled with light by reversible switching of the azobenzene unit, incorporated into the surfactant tail, between a hydrophobic trans (visible irradiation) and a hydrophilic cis (UV irradiation) configuration. The influence of the trans-cis isomerization of the azobenzene on the compaction process of DNA molecules and the role of both isomers in the formation and colloidal stability of DNA-surfactant complexes is discussed. It is shown that the trans isomer plays a major role in the DNA compaction process. The influence of the cis isomer on the DNA coil configuration is rather small. The construction of a phase diagram of the DNA concentration versus surfactant/DNA charge ratio allows distancing between three major phases: colloidally stable and unstable compacted globules, and extended coil conformation. There is a critical concentration of DNA above which the compacted globules can be hindered from aggregation and precipitation by adding an appropriate amount of the surfactant in the trans configuration. This is because of the compensation of hydrophobicity of the globules with an increasing amount of the surfactant. Below the critical DNA concentration, the compacted globules are colloidally stable and can be reversibly transferred with light to an extended coil state.
We report on a process inducing photomechanical fracture of chemical bonds in photosensitive PMAA polymer brushes. The photosensitive PMAA polymer brushes were prepared by covalent attachment of azobenzene groups to poly(methylacrylic acid) (PMAA) chains generated by surface-initiated polymerization. While homogeneous irradiation leaves the polymer topography unchanged, the azo-PMAA brushes show a strong response upon irradiation with UV interference patterns. The photoisomerization process in the surface-attached polymer films results in the irreversible formation of surface relief gratings (SRG), which are strongly enhanced upon washing with a good solvent for the polymer. The photomechanical forces during mass transport induced by the irradiation lead to the scission of covalent bounds and accordingly to a degrafting of the polymer chains in areas where the polymer is receding from. It is observed that the number of ruptured chains depends strongly on the amount of azo side chains in the polymer.
We report on the preparation and characterization of photosensitive polymer brushes. The brushes are synthesized through polymer analogous attachment of azobenzene groups to surface-attached poly(methacrylic acid) (PMAA) chains. The topography of the photosensitive brushes shows a strong reaction upon irradiation with UV light. While homogeneous illumination leaves the polymer topography unchanged, irradiation of the samples with interference patterns with periodically varying light intensity leads to the formation of surface relief gratings (SRG). The height of the stripes of the grating can be controlled by adjusting the irradiation time. The SRG pattern can be erased through solvent treatment when the periodicity of the stripe pattern is less than the length of the fully stretched polymer chains. In the opposite case, photomechanical scission of receding polymer chains is observed during SRG formation, and the inscribed patterns are permanent.