Refine
Year of publication
Document Type
- Article (119)
- Postprint (36)
- Conference Proceeding (3)
- Review (3)
- Other (1)
Language
- English (162)
Keywords
- synthesis (4)
- polyzwitterion (3)
- polyzwitterions (3)
- Block copolymers (2)
- Hydrogel (2)
- LCST behavior (2)
- Polyelectrolytes (2)
- Thermoresponsive (2)
- antifouling (2)
- betaine (2)
Institute
- Institut für Chemie (162) (remove)
This study addresses the effect of ionic strength and type of ions on the structure and water content of polyelectrolyte multilayers. Polyelectrolyte multilayers of poly(sodium-4-styrene sulfonate) (PSS) and poly(diallyl dimethyl ammonium chloride) (PDADMAC) prepared at different NaF, NaCl and NaBr concentrations have been investigated by neutron reflectometry against vacuum, H2O and D2O. Both thickness and water content of the multilayers increase with increasing ionic strength and increasing ion size. Two types of water were identified, "void water" which fills the voids of the multilayers and does not contribute to swelling but to a change in scattering length density and "swelling water" which directly contributes to swelling of the multilayers. The amount of void water decreases with increasing salt concentration and anion radius while the amount of swelling water increases with salt concentration and anion radius. This is interpreted as a denser structure in the dry state and larger ability to swell in water (sponge) for multilayers prepared from high ionic strengths and/or salt solution of large anions. No exchange of hydration water or replacement of H by D was detected even after eight hours incubation time in water of opposing isotopic composition.
Effect of ionic strength and layer number on swelling of polyelectrolyte multilayers in water vapour
(2013)
The swelling behavior of polyelectrolyte multilayers (PEMs) of poly(sodium-4 styrene sulfonate) (PSS) and poly(diallyl dimethyl ammonium chloride) (PDADMAC) prepared from aqueous solution of 0.1 M and 0.5 M NaCl are investigated by ellipsometry and Atomic Force Microscopy (AFM). From 1 double-layer up to 4 double-layers of 0.1 M NaCl, the amount of swelling water in the PEMs decreases with increasing number of adsorbed double layers due to an increase in polyelectrolyte density as a result of the attraction between the positively charged outermost PDADMAC layer and the Si substrate. From 6 double layers to 30 double layers, the attraction is reduced due to a much larger distance between substrate and outermost layer leading to a much lower polyelectrolyte density and higher swelling water. In PEMs prepared from aqueous solution of 0.5 M NaCl, the amount of water constantly increases which is related to a monotonically decreasing polyelectrolyte density with increasing number of polyelectrolyte layers. Studies of the surface topology also indicate a transition from a more substrate affected interphase behavior to a continuum properties of the polyelectrolyte multilayers. The threshold for the transition from interphase to continuum behavior depends on the preparation conditions of the PEM.
A variety of polymerizable lipids containing a hydrophilic spacer group between the reactive group and the main amphiphilic structure have been synthesized. They were investigated in monolayers, liposomes, and multilayers. When the spacer concept was used, efficient decoupling of the motions of the polymeric chain and the amphiphilic side groups is achieved. Thus, the often found loss of the important fluid phases by polymerization is avoided. Polymeric monolayers of the spacer lipid, prepared either by polymerization in the monolayer or by spreading of prepolymerized lipid, exhibit nearly identical surface pressure-area diagrams. Most distinctly, the successful decoupling of the motions of the polymer main chain and the membrane forming amphiphilic side groups is demonstrated by the self-organization of bulk polymerized spacer lipids to polymeric liposomes. In addition, spacer lipids are able to build polymeric Langmuir-Blodgett multilayers. The decoupling of the polymer main chain and the membrane-forming amphiphilic side groups enables the deposition of already polymeric monolayers onto supports to form defined multilayers. If, alternatively, monomeric monolayers are deposited and polymerized on the support, defects in the layers due to structural changes during the polymerization are avoided by the flexible spacer group.
The use of preformed polymers for the preparation of Langmuir-Blodgett (LB) multilayers is reviewed. Principles for polymer self-organization are outlined and the appropriate molecular designs are discussed. Recent developments in the different classes of polymers for LB multilayers are presented, and their outstanding properties highlighted.
A series of new fluorescent dye bearing monomers, including glycomonomers, based on maleamide and maleic esteramide was synthesized. The dye monomers were incorporated by radical copolymerization into thermo-responsive poly(N-vinyl-caprolactam) that displays a lower critical solution temperature (LCST) in aqueous solution. The effects of the local molecular environment on the polymers' luminescence, in particular on the fluorescence intensity and the extent of solvatochromism, were investigated below as well as above the phase transition. By attaching substituents of varying size and polarity in the close vicinity of the fluorophore, and by varying the spacer groups connecting the dyes to the polymer backbone, we explored the underlying structure-property relationships, in order to establish rules for successful sensor designs, e.g., for molecular thermometers. Most importantly, spacer groups of sufficient length separating the fluorophore from the polymer backbone proved to be crucial for obtaining pronounced temperature regulated fluorescence responses.
Langmuir-Blodgett multilayers of hydrocarbon and fluorocarbon polymers with hydrophilic spacer, lipid-polyelectrolyte complexes and mesogenic polymers have been prepared. The thermal behaviour of the multilayers was studied by small angle X-ray scattering, IR and UV—visible spectroscopy. Good thermal stabilities were found for the various classes of polymers. In addition, for both complexed multilayers and mesogenic polymer films, reorientation processes were observed.
This study reports on the investigation of a thermoresponsive polymer as a thin film on electrodes and the influence of coupling a peptide and an antibody to the film. The utilized polymer from the class of poly(oligoethylene glycol)-methacrylate polymers (poly(OEGMA)) with carboxy functions containing side chains was synthesized and properly characterized in aqueous solutions. The dependence of the cloud point on the pH of the surrounding media is discussed. The responsive polymer was immobilized on gold electrodes as shown by electrochemical, quartz crystal microbalance (QCM), and atomic force microscopy (AFM) techniques. The temperature dependent behavior of the polymer covalently grafted to gold substrates is investigated using cyclic voltammetry (CV) in ferro-/ferricyanide solution. Significant changes in the slope of the temperature-dependence of the voltammetric peak current and the peak separation values clearly indicate the thermally induced conformational change on the surface. Finally, a biorecognition reaction between a short FLAG peptide (N-Asp-Tyr-Lys-Asp-Asp-Asp-Asp-Lys-C) covalently immobilized on the polymer interface and the corresponding IgG antibody was performed. The study shows that the responsiveness of the electrode is retained after peptide coupling and antibody binding, although the response is diminished.
New amphiphilic block copolymers consisting of N-vinyl pyrrolidone and vinyl acetate were synthesized via controlled radical polymerization using a reversible addition/fragmentation chain transfer (RAFT)/macromolecular design via the interchange of xanthates (MADIX) system. The synthesis was carried out in 1,4-dioxane as process solvent. In order to get conclusions on the mechanism of the polymerization the molecular structure of formed copolymers was analysed by means of different analytical techniques. C-13 NMR spectroscopy was used for the determination of the monomer ratios. End groups were analysed by means of matrix-assisted laser desorption/ionization time-of-flight mass spectrometry. This technique was also used to determine possible fragmentations of the RAFT end groups. By means of a combination of size exclusion chromatography, C-13 NMR and static light scattering molar mass distributions and absolute molar masses could be analysed. The results clearly show a non-ideal RAFT mechanism.
PVP-block-PVAc block copolymers were synthesized by controlled radical polymerization applying a RAFT/MADIX system and were investigated by HPLC and by coupling of chromatography to FT-IR spectroscopy and MALDI-TOF MS. Chromatographic methods (LACCC and gradient techniques) were developed that allowed a separation of block copolymers according to their repeating units. The results of the spectroscopic and spectrometric analysis clearly showed transfer between radicals and process solvent. With the use of hyphenated techniques differences between main and side products were detected. In agreement with previously published results, obtained by NMR, SEC, static light scattering and MALDI- TOF MS, our data proved a non-ideal RAFT polymerization.
Adhesion control in liquidliquidsolid systems represents a challenge for applications ranging from self-cleaning to biocompatibility of engineered materials. By using responsive polymer chemistry and molecular self-assembly, adhesion at solid/liquid interfaces can be achieved and modulated by external stimuli. Here, we utilize thermosensitive polymeric materials based on random copolymers of di(ethylene glycol) methyl ether methacrylate (x = MEO(2)MA) and oligo(ethylene glycol) methyl ether methacrylate (y = OEGMA), that is, P(MEO(2)MA(x)-co-OEGMA(y)), to investigate the role of hydrophobicity on the phenomenon of adhesion. The copolymer ratio (x/y) dictates macromolecular changes enabling control of the hydrophilic-to-lipophilic balance (HBL) of the polymer brushes through external triggers such as ionic strength and temperature. We discuss the HBL of the thermobrushes in terms of the surface energy of the substrate by measuring the contact angle at waterdecaneP(MEO(2)MA(x)-co-OEGMA(y)) brush contact line as a function of polymer composition and temperature. Solid supported polyelectrolyte layers grafted with P(MEO(2)MA(x)-co-OEGMA(y)) display a transition in the wettability that is related to the lower critical solution temperature of the polymer brushes. Using experimental observation of the hydrophilic to hydrophobic transition by the contact angle, we extract the underlying energetics associated with liquidliquidsolid adhesion as a function of the copolymer ratio. The change in cellular attachment on P(MEO(2)MA(x)-co-OEGMA(y)) substrates of variable (x/y) composition demonstrates the subtle role of compositional tuning on the ability to control liquidliquidsolid adhesion in biological applications.
New amphiphilic diblock copolymers : surfactant properties and solubilization in their micelles
(2006)
Several series of amphiphilic diblock copolymers are investigated as macrosurfactants in comparison to reference low-molar-mass and polymeric surfactants. The various copolymers share poly(butyl acrylate) as a common hydrophobic block but are distinguished by six different hydrophilic blocks (one anionic, one cationic, and four nonionic hydrophilic blocks) with various compositions. Dynamic light scattering experiments indicate the presence of micelles over the whole concentration range from 10(-4) to 10 g(.)L(-1). Accordingly, the critical micellization concentrations are very low. Still, the surface tension of aqueous solutions of block copolymers decreases slowly but continuously with increasing concentration, without exhibiting a plateau. The longer the hydrophobic block, the shorter the hydrophilic block, and the less hydrophilic the monomer of the hydrophilic block is, the lower the surface tension is. However, the effects are small, and the copolymers reduce the surface tension much less than standard low-molar-mass surfactants. Also, the copolymers foam much less and even act as anti-foaming agents in classical foaming systems composed of standard surfactants. The copolymers stabilize O/W emulsions made of methyl palmitate as equally well as standard surfactants but are less efficient for O/W emulsions made of tributyrine. However, the copolymer micelles exhibit a high solubilization power for hydrophobic dyes, probably at their core-corona interface, in dependence on the initial geometry of the micelles and the composition of the block copolymers. Whereas micelles of copolymers with strongly hydrophilic blocks are stable upon solubilization, solubilization-induced micellar growth is observed for copolymers with moderately hydrophilic blocks
To systematically add functionality to nanoscale polymer switches, an understanding of their responsive behavior is crucial. Herein, solvent vapor stimuli are applied to thin films of a diblock copolymer consisting of a short poly(methyl methacrylate) (PMMA) block and a long poly(N-isopropylmethacrylamide) (PNIPMAM) block for realizing ternary nanoswitches. Three significantly distinct film states are successfully implemented by the combination of amphiphilicity and co-nonsolvency effect. The exposure of the thin films to nitrogen, pure water vapor, and mixed water/acetone (90 vol%/10 vol%) vapor switches the films from a dried to a hydrated (solvated and swollen) and a water/acetone-exchanged (solvated and contracted) equilibrium state. These three states have distinctly different film thicknesses and solvent contents, which act as switch positions "off," "on," and "standby." For understanding the switching process, time-of-flight neutron reflectometry (ToF-NR) and spectral reflectance (SR) studies of the swelling and dehydration process are complemented by information on the local solvation of functional groups probed with Fourier-transform infrared (FTIR) spectroscopy. An accelerated responsive behavior beyond a minimum hydration/solvation level is attributed to the fast build-up and depletion of the hydration shell of PNIPMAM, caused by its hydrophobic moieties promoting a cooperative hydration character.
Homopolymers of N-acryloyl glycinamide were prepared by reversible addition-fragmentation chain transfer polymerization in water. The formed macromolecules exhibit strong polymer-polymer interactions in aqueous milieu and therefore form thermoreversible physical hydrogels in pure water, physiological buffer or cell medium.
We report on the growth and structure of hybrid clay-based multilayers obtained by electrostatic self-assembly (also known as layer-by-layer assembly) of poly(diallylpyrrolidinium bromide) and a synthetic hectorite (Laponite). By combining ellipsometry, atomic force microscopy, and specular and off-specular grazing angle X-ray scattering measurements, we show that platelets pack in the vertical direction according to a distribution of distances between nearest neighbors of about 3 Å standard deviation. The accumulation of such random fluctuations in the vertical direction results in the loss of layering of the platelets farther than about 75 Å from the substrate. In this respect, most of the film should be considered as a nanocomposite with preferential orientation of the platelets, rather than as a real multilayer. The model is quantitatively supported by simulations of the specular and off-specular scattering of such multilayers.
The influence of the charge density of polyelectrolytes on the growth of polyelectrolyte multilayers via layer- by-layer self-assembly from pure aqueous solutions was studied. Multilayers were built from strong polyanions, namely poly(styrenesulfonate) and an exfoliated synthetic hectorite, and cationic copolymers of diallyldimethylammonium chloride (DADMAC) with N-methyl-N-vinylformamide (NMVF) for which the composition and thus the charge density was varied systematically. The analysis of the system {cationic copolymer/poly(styrenesulfonate)} reveals that a critical linear charge density Ïc of 0.036 elementary charge/Å of contour length is necessary to obtain stable multilayer growth in pure water. Above Ïc, the increment of thickness/deposition cycle varies with the linear charge density of the cationic copolymers, in good agreement with current theories of polyelectrolyte solutions. As linear charge density increases, the system passes successively through a charge-dependent ?Debye-Hu ckel? regime and then through a chargeindependent ?strong-screening? regime where counterion condensation dominates the behavior. Analogous results were obtained for the variation of the basal spacing of internally structured hybrid multilayers {cationic copolymer/hectorite}. However, by contrast with the first system, no critical linear charge density was found for the hybrid system. This is explained by additional, nonelectrostatic interactions between the clay platelets and the formamide fragment.
The free volume in thin films of poly(N-isopropylacrylamid) end-capped with n-butyltrio-carbonate (nbc-PNIPAM) is probed with positron annihilation lifetime spectroscopy (PALS). The PALS measurements are performed as function of energy to obtain depth profiles of the free volume of nbc-PNIPAM films. The range of nbc-PNIPAM films with thicknesses from 40 to 200 nm is focused. With decreasing film thickness the free volume increases in good agreement with an increase in the maximum swelling capability of the nbc-PNIPAM films. Thus in thin hydrogel films the sorption and swelling behavior is governed by free volume.
Multifunctional chain transfer agents for RAFT polymerisation were designed for the one-step synthesis of amphiphilic star polymers. Thus, hydrophobically end-capped 3- and 4-arm star polymers, as well as linear ones for reference, were made of the hydrophilic monomer N,N-dimethylacrylamide (DMA) in high yield with molar masses up to 150 000 g mol(-1), narrow molar mass distribution (PDI <= 1.2) and high end group functionality (similar to 90%). The associative telechelic polymers form transient networks of interconnected aggregates in aqueous solution, thus acting as efficient viscosity enhancers and rheology modifiers, eventually forming hydrogels. The combination of dynamic light scattering (DLS), small angle neutron scattering (SANS) and rheology experiments revealed that several molecular parameters control the structure and therefore the physical properties of the aggregates. In addition to the size of the hydrophilic block (maximum length for connection) and the length of the hydrophobic alkyl chain ends (stickiness), the number of arms (functionality) proved to be a key parameter.
Radical addition fragmentation chain transfer (RAFT) polymerization of ferrocenyl (meth)acrylates
(2012)
We report on the controlled free radical homopolymerization of 1-ferrocenylethyl acrylate as well as of three new ferrocene bearing monomers, namely 4-ferrocenylbutyl acrylate, 2-ferrocenylamido-2-methylpropyl acrylate, and 4-ferrocenylbutyl methacrylate, by the RAFT technique. For comparison, the latter monomer was polymerized using ATRP, too. The ferrocene containing monomers were found to be less reactive than their analogues free of ferrocene. The reasons for the low polymerizability are not entirely clear. As the addition of free ferrocene to the reaction mixture did not notably affect the polymerizations, sterical hindrance by the bulky ferrocene moiety fixed on the monomers seems to be the most probable explanation. Molar masses found for 1-ferrocenylethyl acrylate did not exceed 10,000 g mol(-1), while for 4-ferrocenylbutyl (meth) acrylate molar masses of 15,000 g mol(-1) could be obtained. With PDIs as low as 1.3 in RAFT polymerization of the monomers, good control over the polymerization was achieved.
A series of new sulfobetaine methacrylates, including nitrogen-containing saturated heterocycles, was synthesised by systematically varying the substituents of the zwitterionic group. Radical polymerisation via the RAFT (reversible addition–fragmentation chain transfer) method in trifluoroethanol proceeded smoothly and was well controlled, yielding polymers with predictable molar masses. Molar mass analysis and control of the end-group fidelity were facilitated by end-group labeling with a fluorescent dye. The polymers showed distinct thermo-responsive behaviour of the UCST (upper critical solution temperature) type in an aqueous solution, which could not be simply correlated to their molecular structure via an incremental analysis of the hydrophilic and hydrophobic elements incorporated within them. Increasing the spacer length separating the ammonium and the sulfonate groups of the zwitterion moiety from three to four carbons increased the phase transition temperatures markedly, whereas increasing the length of the spacer separating the ammonium group and the carboxylate ester group on the backbone from two to three carbons provoked the opposite effect. Moreover, the phase transition temperatures of the analogous polyzwitterions decreased in the order dimethylammonio > morpholinio > piperidinio alkanesulfonates. In addition to the basic effect of the polymers’ precise molecular structure, the concentration and the molar mass dependence of the phase transition temperatures were studied. Furthermore, we investigated the influence of added low molar mass salts on the aqueous-phase behaviour for sodium chloride and sodium bromide as well as sodium and ammonium sulfate. The strong effects evolved in a complex way with the salt concentration. The strength of these effects depended on the nature of the anion added, increasing in the order sulfate < chloride < bromide, thus following the empirical Hofmeister series. In contrast, no significant differences were observed when changing the cation, i.e. when adding sodium or ammonium sulfate.
Complementary to the well-established zwitterionic monomer 3-((3-methacrylamidopropyl)dimethylammonio) propane-1-sulfonate (SPP), the closely related monomers 2-hydroxy-3-((3-methacrylamidopropyl) dimethylammonio)propane-1-sulfonate (SHPP) and 4-((3-methacrylamidopropyl)dimethylammonio)-butane-1-sulfonate (SBP) were synthesised and polymerised by reversible addition–fragmentation chain transfer (RAFT) polymerisation, using a fluorophore labeled RAFT agent. The polyzwitterions of systematically varied molar masses were characterised with respect to their solubility in water and aqueous salt solutions. Both poly(sulfobetaine)s show thermoresponsive behaviour in water, exhibiting phase separation at low temperatures and upper critical solution temperatures (UCST). For both polySHPP and polySBP, cloud points depend notably on the molar mass, and are much higher in D2O than in H2O. Also, the cloud points are effectively modulated by the addition of salts. The individual effects can be in parts correlated to the Hofmeister series for the anions studied. Still, they depend in a complex way on the concentration and the nature of the added electrolytes, on the one hand, and on the detailed nature of the spacer group separating the anionic and the cationic charges of the betaine moiety, on the other hand. As anticipated, the cloud points of polySBP are much higher than the ones of the analogous polySPP of identical molar mass. Surprisingly, the cloud points of polySHPP are also somewhat higher than the ones of their polySPP analogues, despite the additional hydrophilic hydroxyl group present in the spacer separating the ammonium and the sulfonate moieties. These findings point to a complicated interplay of the various hydrophilic components in polyzwitterions with respect to their overall hydrophilicity. Thus, the spacer group in the betaine moiety proves to be an effective additional molecular design parameter, apparently small variations of which strongly influence the phase behaviour of the polyzwitterions in specific aqueous environments.
The kinetics of water transfer between the lower critical solution temperature (LCST) and upper critical solution temperature (UCST) thermoresponsive blocks in about 10 nm thin films of a diblock copolymer is monitored by in situ neutron reflectivity. The UCST-exhibiting block in the copolymer consists of the zwitterionic poly(4((3-methacrylamidopropyl)dimethylammonio)butane-1-sulfonate), abbreviated as PSBP. The LCST-exhibiting block consists of the nonionic poly(N-isopropylacrylamide), abbreviated as PNIPAM. The as-prepared PSBP80-b-PNIPAM(400) films feature a three-layer structure, i.e., PNIPAM, mixed PNIPAM and PSBP, and PSBP. Both blocks have similar transition temperatures (TTs), namely around 32 degrees C for PNIPAM, and around 35 degrees C for PSBP, and with a two-step heating protocol (20 degrees C to 40 degrees C and 40 degrees C to 80 degrees C), both TTs are passed. The response to such a thermal stimulus turns out to be complex. Besides a three-step process (shrinkage, rearrangement, and reswelling), a continuous transfer of D2O from the PNIPAM to the PSBP block is observed. Due to the existence of both, LCST and UCST blocks in the PSBP80-b-PNIPAM(400 )film, the water transfer from the contracting PNIPAM, and mixed layers to the expanding PSBP layer occurs. Thus, the hydration kinetics and thermal response differ markedly from a thermoresponsive polymer film with a single LCST transition.
We demonstrate new fluorophore-labelled materials based on acrylamide and on oligo(ethylene glycol) (OEG) bearing thermoresponsive polymers for sensing purposes and investigate their thermally induced solubility transitions. It is found that the emission properties of the polarity-sensitive (solvatochromic) naphthalimide derivative attached to three different thermoresponsive polymers are highly specific to the exact chemical structure of the macromolecule. While the dye emits very weakly below the LCST when incorporated into poly(N-isopropylacrylamide) (pNIPAm) or into a polyacrylate backbone bearing only short OEG side chains, it is strongly emissive in polymethacrylates with longer OEG side chains. Heating of the aqueous solutions above their cloud point provokes an abrupt increase of the fluorescence intensity of the labelled pNIPAm, whereas the emission properties of the dye are rather unaffected as OEG-based polyacrylates and methacrylates undergo phase transition. Correlated with laser light scattering studies, these findings are ascribed to the different degrees of pre-aggregation of the chains at low temperatures and to the extent of dehydration that the phase transition evokes. It is concluded that although the temperature-triggered changes in the macroscopic absorption characteristics, related to large-scale alterations of the polymer chain conformation and aggregation, are well detectable and similar for these LCST-type polymers, the micro-environment provided to the dye within each polymer network differs substantially. Considering sensing applications, this finding is of great importance since the temperature-regulated fluorescence response of the polymer depends more on the macromolecular architecture than the type of reporter fluorophore.
We demonstrate new fluorophore-labelled materials based on acrylamide and on oligo(ethylene glycol) (OEG) bearing thermoresponsive polymers for sensing purposes and investigate their thermally induced solubility transitions. It is found that the emission properties of the polarity-sensitive (solvatochromic) naphthalimide derivative attached to three different thermoresponsive polymers are highly specific to the exact chemical structure of the macromolecule. While the dye emits very weakly below the LCST when incorporated into poly(N-isopropylacrylamide) (pNIPAm) or into a polyacrylate backbone bearing only short OEG side chains, it is strongly emissive in polymethacrylates with longer OEG side chains. Heating of the aqueous solutions above their cloud point provokes an abrupt increase of the fluorescence intensity of the labelled pNIPAm, whereas the emission properties of the dye are rather unaffected as OEG-based polyacrylates and methacrylates undergo phase transition. Correlated with laser light scattering studies, these findings are ascribed to the different degrees of pre-aggregation of the chains at low temperatures and to the extent of dehydration that the phase transition evokes. It is concluded that although the temperature-triggered changes in the macroscopic absorption characteristics, related to large-scale alterations of the polymer chain conformation and aggregation, are well detectable and similar for these LCST-type polymers, the micro-environment provided to the dye within each polymer network differs substantially. Considering sensing applications, this finding is of great importance since the temperature-regulated fluorescence response of the polymer depends more on the macromolecular architecture than the type of reporter fluorophore.
A water soluble fluorescent polymer as a dual colour sensor for temperature and a specific protein
(2013)
We present two thermoresponsive water soluble copolymers prepared via free radical statistical copolymerization of N-isopropylacrylamide (NIPAm) and of oligo(ethylene glycol) methacrylates (OEGMAs), respectively, with a solvatochromic 7-(diethylamino)-3-carboxy-coumarin (DEAC)- functionalized monomer. In aqueous solutions, the NIPAm-based copolymer exhibits characteristic changes in its fluorescence profile in response to a change in solution temperature as well as to the presence of a specific protein, namely an anti-DEAC antibody. This polymer emits only weakly at low temperatures, but exhibits a marked fluorescence enhancement accompanied by a change in its emission colour when heated above its cloud point. Such drastic changes in the fluorescence and absorbance spectra are observed also upon injection of the anti-DEAC antibody, attributed to the specific binding of the antibody to DEAC moieties. Importantly, protein binding occurs exclusively when the polymer is in the well hydrated state below the cloud point, enabling a temperature control on the molecular recognition event. On the other hand, heating of the polymer–antibody complexes releases a fraction of the bound antibody. In the presence of the DEAC-functionalized monomer in this mixture, the released antibody competitively binds to the monomer and the antibody-free chains of the polymer undergo a more effective collapse and inter-aggregation. In contrast, the emission properties of the OEGMA-based analogous copolymer are rather insensitive to the thermally induced phase transition or to antibody binding. These opposite behaviours underline the need for a carefully tailored molecular design of responsive polymers aimed at specific applications, such as biosensing.
A water soluble fluorescent polymer as a dual colour sensor for temperature and a specific protein
(2013)
We present two thermoresponsive water soluble copolymers prepared via free radical statistical copolymerization of N-isopropylacrylamide (NIPAm) and of oligo(ethylene glycol) methacrylates (OEGMAs), respectively, with a solvatochromic 7-(diethylamino)-3-carboxy-coumarin (DEAC)-functionalized monomer. In aqueous solutions, the NIPAm-based copolymer exhibits characteristic changes in its fluorescence profile in response to a change in solution temperature as well as to the presence of a specific protein, namely an anti-DEAC antibody. This polymer emits only weakly at low temperatures, but exhibits a marked fluorescence enhancement accompanied by a change in its emission colour when heated above its cloud point. Such drastic changes in the fluorescence and absorbance spectra are observed also upon injection of the anti-DEAC antibody, attributed to the specific binding of the antibody to DEAC moieties. Importantly, protein binding occurs exclusively when the polymer is in the well hydrated state below the cloud point, enabling a temperature control on the molecular recognition event. On the other hand, heating of the polymer-antibody complexes releases a fraction of the bound antibody. In the presence of the DEAC-functionalized monomer in this mixture, the released antibody competitively binds to the monomer and the antibody-free chains of the polymer undergo a more effective collapse and inter-aggregation. In contrast, the emission properties of the OEGMA-based analogous copolymer are rather insensitive to the thermally induced phase transition or to antibody binding. These opposite behaviours underline the need for a carefully tailored molecular design of responsive polymers aimed at specific applications, such as biosensing.
While zwitterionic interfaces are known for their excellent low-fouling properties, the underlying molecular principles are still under debate. In particular, the role of the zwitterion orientation at the interface has been discussed recently. For elucidation of the effect of this parameter, self-assembled monolayers (SAMs) on gold were prepared from stoichiometric mixtures of oppositely charged alkyl thiols bearing either a quaternary ammonium or a carboxylate moiety. The alkyl chain length of the cationic component (11-mercaptoundecyl)-N,N,N-trimethylammonium, which controls the distance of the positively charged end group from the substrate's surface, was kept constant. In contrast, the anionic component and, correspondingly, the distance of the negatively charged carboxylate groups from the surface was varied by changing the alkyl chain length in the thiol molecules from 7 (8-mercaptooctanoic acid) to 11 (12-mercaptododecanoic acid) to 15 (16-mercaptohexadecanoic acid). In this way, the charge neutrality of the coating was maintained, but the charged groups exposed at the interface to water were varied, and thus, the orientation of the dipoles in the SAMs was altered. In model biofouling studies, protein adsorption, diatom accumulation, and the settlement of zoospores were all affected by the altered charge distribution. This demonstrates the importance of the dipole orientation in mixed-charged SAMs for their inertness to nonspecific protein adsorption and the accumulation of marine organisms. Overall, biofouling was lowest when both the anionic and the cationic groups were placed at the same distance from the substrate's surface.
Sediment challenge to promising ultra-low fouling hydrophilic surfaces in the marine environment
(2019)
Hydrophilic coatings exhibit ultra-low fouling properties in numerous laboratory experiments. In stark contrast, the antifouling effect of such coatings in vitro failed when performing field tests in the marine environment. The fouling release performance of nonionic and zwitterionic hydrophilic polymers was substantially reduced compared to the controlled laboratory environment. Microscopy and spectroscopy revealed that a large proportion of the accumulated material in field tests contains inorganic compounds and diatomaceous soil. Diatoms adhered to the accumulated material on the coating, but not to the pristine polymer. Simulating field tests in the laboratory using sediment samples collected from the test sites showed that incorporated sand and diatomaceous earth impairs the fouling release characteristics of the coatings. When exposed to marine sediment from multiple locations, particulate matter accumulated on these coatings and served as attachment points for diatom adhesion and enhanced fouling. Future developments of hydrophilic coatings should consider accumulated sediment and its potential impact on the antifouling performance.
Cinnamic acid moieties were incorporated into amphiphilic compounds containing one and two alkyl chains. These lipid-like compounds with photoreactive units undergo self-organization to form monolayers at the gas-water interface and bilayer structures (vesicles) in aqueous solutions. The photoreaction of the cinnamic acid moiety induced by 254 nm UV light was investigated in the crystalline state, in monolayers, in vesicles and in solution in organic solvents. The single-chain amphiphiles undergo dimerization to yield photoproducts with twice the molecular weight of the corresponding monomers in organized systems. The photoreaction of amphiphiles containing two cinnamic acid groups occurs via two mechanisms: The intramolecular dimerization produces bicycles, with retention of the molecular weight of the corresponding monomer. The intermolecular reaction leads to oligomeric and polymeric photoproducts. In contrast to the single-chain amphiphiles, photodimerization processes of lipoids containing two cinnamic acid moieties also occur in solution in organic solvents.
Electrostatically self-assembled (ESA) polyelectrolyte films show in general no internal structure. The use of special polycations, however, namely of lyotropic ionenes, may give rise to highly ordered coatings. In this article, the influence of the charge density of the polyanion, as well as the distribution of the charged groups within this polymer, is examined, using a series of anionic cellulose derivatives. Various techniques were used to study the films? growth and internal structure. Both showed to be affected in particular by the charge density but also by the substitution pattern.
A novel perfluorinated magnesium phthalocyanine (MgPcF64) was synthesized and employed to probe nanodomains in hydrophobically modified, amphiphilic cationic polyelectrolytes bearing alkyl and/or fluoroalkyl side chains. MgPcF64 was found to be solubilized exclusively in the aqueous solutions of the fluorocarbon modified polycations, occupying the perfluorinated nanocompartments provided, while analogous polyelectrolytes with alkyl side chains forming hydrocarbon nanocompartments could not host the MgPcF64 dye. Multilayer films were fabricated by means of the layer-by-layer (LbL) deposition method using sodium poly(styrene sulfonate) as a polyanion. Linear multilayer growth was confirmed by UV-Vis spectroscopy and spectroscopic ellipsometry. Atomic force microscopy studies indicated that the micellar conformation of the polycations is preserved in the multilayer films. Fluorescence spectroscopy measurements confirmed that MgPcF64 stays embedded inside the fluorocarbon domains after the deposition process. This facile way of selectively incorporating water-insoluble, photoactive molecules into the structure of polyelectrolyte multilayers may be utilized for nanoengineering of ultrathin film-based optoelectronic devices.
Micellar multilayer films were prepared from an amphiphilic comb-like polycation ("polysoap") and the polyanion poly(styrene sulfonate) (PSS) using alternate polyelectrolyte layer-by-layer (LbL) self-assembly. Linear growth of the film thickness was evidenced by UV-vis spectroscopy and spectroscopic ellipsometry. Imaging by atomic force microscopy (AFM) indicated that the micellar conformation adopted by the polycation in solutions was preserved in the films. Thus, hydrophobic photoactive molecules, which were solubilized by the hydrophobic nanodomains of the micellar polymer prior to deposition, could be transferred into the films. Photoinduced energy transfer was observed in the nanostructured multilayers between naphthalene (donor) and perylene (acceptor) molecules embedded inside the polymer micelles. The efficiency of the energy transfer process can be controlled to some extent by introducing spacer layers between the layers containing the donor or acceptor, revealing partial stratification of the micellar LbL films. Also, photoinduced electron transfer was evidenced between perylene (donor) and butyl viologen (acceptor) molecules embedded inside the multilayers by steady-state fluorescence spectroscopy. The obtained photoactive nanostructures are promising candidates for solar-to-chemical energy conversion systems.
Cationic ionenes bearing hydrophobic side chains were synthesized, which behave as micellar polymers of the polysoap type. The hydrophobic chains were either hydrocarbons or fluorocarbons, or a mixture of both, in the form of statistical as well as block copolymers. These amphiphilic polymers were studied and compared with each other and with low molar mass analogous surfactants, especially with respect to their hydrophobic association in aqueous solution. The particular molecular structure of the ionenes synthesized results in polymeric surfactants with high mobility of the fluorocarbon chains. Most noteworthy, the behavior of the hydrocarbon-fluorocarbon block copolymer soaps in aqueous solution indicates microphase separation into hydrocarbon-rich and fluorocarbon-rich hydrophobic domains, thus yielding multicompartment micelles.
The swelling and co-nonsolvency behaviors in pure H2O and in a mixed H2O/CH3OH vapor atmosphere of two different polar, water-soluble polymers in thin film geometry are studied in situ. Films of a zwitterionic poly(sulfobetaine), namely, poly[3-((2-(methacryloyloxy)ethyl)dimethylammonio) propane-1-sulfonate] (PSPE), and a polar nonionic polymer, namely, poly(N-isopropylmethacrylamide) (PNIPMAM), are investigated in real time by spectral reflectance (SR) measurements and Fourier transform infrared (FTIR) spectroscopy. Whereas PSPE is insoluble in methanol, PNIPMAM is soluble but exhibits cononsolvency behavior in water/methanol mixtures. First, the swelling of PSPE and PNIPMAM thin films in H2O vapor is followed. Subsequently, CH3OH is added to the vapor atmosphere, and its contracting effect on the water-swollen films is monitored, revealing a co-nonsolvency-type behavior for PNIPMAM and PSPE. SR measurements indicate that PSPE and PNIPMAM behave significantly different during the H2O swelling and subsequent exposure to CH3OH, not only with respect to the amounts of absorbed water and CH3OH, but also to the cosolvent-induced contraction mechanisms. While PSPE thin films exhibit an abrupt one-step contraction, the contraction of PNIPMAM thin films occurs in two steps. FTIR studies corroborate these findings on a molecular scale and reveal the role of the specific functional groups, both during the swelling and the cosolvent-induced switching of the solvation state.
The water vapor-induced swelling, as well as subsequent phase-transition kinetics, of thin films of a diblock copolymer (DBC) loaded with different amounts of the salt NaBr, is investigated in situ. In dilute aqueous solution, the DBC features an orthogonally thermoresponsive behavior. It consists of a zwitterionic poly(sulfobetaine) block, namely, poly(4-(N-(3'-methacrylamidopropyl)-N, N-dimethylammonio) butane-1-sulfonate) (PSBP), showing an upper critical solution temperature, and a nonionic block, namely, poly(N-isopropylmethacrylamide) (PNIPMAM), exhibiting a lower critical solution temperature. The swelling kinetics in D2O vapor at 15 degrees C and the phase transition kinetics upon heating the swollen film to 60 degrees C and cooling back to 15 degrees C are followed with simultaneous time-of-flight neutron reflectometry and spectral reflectance measurements. These are complemented by Fourier transform infrared spectroscopy. The collapse temperature of PNIPMAM and the swelling temperature of PSBP are found at lower temperatures than in aqueous solution, which is attributed to the high polymer concentration in the thin-film geometry. Upon inclusion of sub-stoichiometric amounts (relative to the monomer units) of NaBr in the films, the water incorporation is significantly increased. This increase is mainly attributed to a salting-in effect on the zwitterionic PSBP block. Whereas the addition of NaBr notably shifts the swelling temperature of PSBP to lower temperatures, the collapse temperature of PNIPMAM remains unaffected by the presence of salt in the films.
The humidity-induced swelling and exchange behavior of a block copolymer thin film, which consists of a zwitterionic poly(sulfobetaine) [poly(N,N-dimethyl-N-(3-(methacrylamido)propyl)ammoniopropanesulfonate) (PSPP)] block and a nonionic poly(N-isopropylacrylamide) (PNIPAM) block, are investigated by time-of-flight neutron reflectometry (TOF-NR). We monitor in situ the swelling in the H2O atmosphere, followed by an exchange with D2O. In the reverse experiment, swelling in the D2O atmosphere and the subsequent exchange with H2O are studied. Both, static and kinetic TOF-NR measurements indicate significant differences in the interactions between the PSPP80-b-PNIPAM(130) thin film and H2O or D2O, which we attribute to the different H- and D-bonds between water and the polymer. Changes in the chain conformation and hydrogen bonding are probed with Fourier transform infrared spectroscopy during the kinetics of the swelling and exchange processes, which reveals the key roles of the ionic SO3- group in the PSPP block and of the polar amide groups of both blocks during water uptake and exchange.
In the present paper, the influence of the surfactant concentration and the degree of charge of a polymer on foam film properties of oppositely charged polyelectrolyte/surfactant mixtures has been investigated. To verify the assumption that the position of the isoelectric point (IEP) does not change the character of the foam film stabilities, the position of the IEP of the polyelectrolyte/surfactant mixtures has been shifted in two different ways. Within the first series of experiments, the foam. film properties were studied using a fixed surfactant concentration of 3 x 10(-5) M in the mixture. Due to the low surfactant concentration, this is a rather dilute system. In the second approach, a copolymer of nonionic and ionic monomer units was Used to lower the charge density of the polymer. This gave rise to additional interactions between the polyelectrolyte and the surfactant, which makes the description of the foam film behavior more complex. In both systems, the same characteristics of the foam film stabilities were found: The foam film stability is reduced toward the IEP of the system, followed by a destabilization around the IEP., At polyelectrolyte concentrations above the IEP, foam films are very stable. However, the concentration range where unstable films were formed was rather broad, and the mechanisms leading to the destabilization had different origins. The results were compared with former findings on PAMPS/C(14)TAB mixtures with an IEP of 10(-4)M.(1)
Thermoresponsive block copolymers comprising long, hydrophilic, nonionic poly(methoxy diethylene glycol acrylate) (PMDEGA) blocks and short hydrophobic polystyrene (PS) blocks are investigated in aqueous solution. Various architectures, namely diblock, triblock, and starblock copolymers are studied as well as a PMDEGA homopolymer as reference, over a wide concentration range. For specific characterization methods, polymers were labeled, either by partial deuteration (for neutron scattering studies) or by fluorophores. Using fluorescence correlation spectroscopy, critical micellization concentrations are identified and the hydrodynamic radii of the micelles, r (h) (mic) , are determined. Using dynamic light scattering, the behavior of r (h) (mic) in dependence on temperature and the cloud points are measured. Small-angle neutron scattering enabled the detailed structural investigation of the micelles and their aggregates below and above the cloud point. Viscosity measurements are carried out to determine the activation energies in dependence on the molecular architecture. Differential scanning calorimetry at high polymer concentration reveals the glass transition of the polymers, the fraction of uncrystallized water and effects of the phase transition at the cloud point. Dielectric relaxation spectroscopy shows that the polarization changes reversibly at the cloud point, which reflects the formation of large aggregates upon heating through the cloud point and their redissolution upon cooling.
We investigate the cononsolvency effect of poly(N-isopropylacrylamide) (PNIPAM) in mixtures of water and methanol. Two systems are studied: micellar solutions of polystyrene-b-poly(N-isopropylacrylamide) (PS-b-PNIPAM) diblock copolymers and, as a reference, solutions of PNIPAM homopolymers, both at a concentration of 20 mg/mL in DO. Using a stopped-flow instrument, fully deuterated methanol was rapidly added to these solutions at volume fractions between 10 and 20%. Time-resolved turbidimetry revealed aggregate formation within 10-100 s. The structural changes on mesoscopic length scales were followed by time-resolved small-angle neutron scattering (TR-SANS) with a time resolution of 0.1 s. In both systems, the pathway of the aggregation depends on the content of deuterated methanol; however, it is fundamentally different for homopolymer and diblock copolymer solutions: In the former, very large aggregates (>150 nm) are formed within the dead time of the setup, gradient appears at their surface in the late stages. In contrast, the growth of the aggregates in the latter system features different regimes, and the final aggregate size is 50 nm, thus much smaller than for the homopolymer. For the diblock copolymer, the time dependence of the aggregate radius can be described by two models: In the initial stage, the diffusion-limited coalescence model describes the data well; however, the resulting coalescence time is unreasonably high. In the late stage, a logarithmic coalescence model based on an energy barrier which is proportional to the aggregate radius is successfully applied. and a concentration
The prepaparation of amorphous, homogeneous blends of zwitterionic polymers and transition metal salts was investigated. Homogeneous miscibility was achieved in many cases up to equimolar amounts of salt, depending on the anion and cation chosen. Various analytical techniques point to a solid state solution of the inorganic ions in the polymer matrix.
A set of novel zwitterionic side-chain polyacrylates and polymethacrylates is studied by X-ray scattering. The structural order both in the short-range and long-range scale is investigated. The influence of the polymer backbone, of different locations of the ionic groups in isomeric polymers, of bound water and of added inorganic salts on the bulk structures is studied, and the observed rearrangements are analysed.
We studied the swelling of polyelectrolyte (PE) multilayers (PEM) in water (H2O) vapors. The PEM were made from polyanion poly(styrene sulfonate) (PSS) and polycation poly(diallyldimethylammonium chloride)-N-methyl-N-vinylacetamide (pDADMAC-NMVA). While PSS is a fully charged polyanion, pDADMAC-NMVA is a random copolymer made of charged pDADMAC and uncharged NMVA monomer units. Variation of the relative amount of these two units allows for controlling the charge density of pDADMAC-NMVA. The degree of swelling was studied as it function of the relative humidity in the experimental chamber (respectively water concentration in the gas phase) for PEM prepared from PSS and pDADMAC-NMVA with their different charge densities - 100%, 89% and 75%. The films were prepared by means of spraying technique and consisted of six PE couples-PSS/pDADMAC-NMVA. Neutron reflectometry was applied as main tool to observe the swelling process. The technique allows to obtain in a single experiment information about film thickness and amount of water in the film. The experiments were complemented with AFM measurements to obtain the thickness of the films. It was found that the Film thickness increases when the charge density of the polycation decreases. The swelling of the PEM increases with the relative humidity and it depends on the charge density of pDADMAC-NMVA. The swelling behavior is 2-fold, splitting up in a charge dependent mode with relatively little volume increase, and a second mode With high volume expansion, which is independent from charge density of PEM. The "swelling transition" occurs for all samples at a relative humidity about 60% and a volume increase of ca. 20%. The results were interpreted according to the Flory-Huggins theory which assumes a phase separation in PEM network at higher water contents.
Polymeric Surfactants
(2003)
The article reviews water-soluble polymers characterized by surfactant side chains, and related amphiphilic polymers. Various synthetic approaches are presented, and rules for useful molecular architectures are given. Models for the self-organization of such polymers in water are presented comparing them with the micellization of low molecular weight surfactants. Highlighting key properties of aqueous polysoap solutions such as viscosity, surface tension and solubilization power, some structure-property relationships are established. Further, the formation of mesophases and of superstructures in bulk is addressed. Finally, the functionalization of polysoaps, and potential applications are discussed.
The structures and synthesis of polyzwitterions ("polybetaines") are reviewed, emphasizing the literature of the past decade. Particular attention is given to the general challenges faced, and to successful strategies to obtain polymers with a true balance of permanent cationic and anionic groups, thus resulting in an overall zero charge. Also, the progress due to applying new methodologies from general polymer synthesis, such as controlled polymerization methods or the use of "click" chemical reactions is presented. Furthermore, the emerging topic of responsive ("smart") polyzwitterions is addressed. The considerations and critical discussions are illustrated by typical examples.
Contents: 1. Discotic Liquid Crystals 2. Monolayers and Langmuir-Blodgett Multilayers 3. Theoretical Considerations on the Molecular Packing of Discotic LCs in Monolayers and Multilayers 4. Spreading Experiments with Discotic LCs 5. LB-Multilayers of Discotic LCs 6. Polymeric Discotic LCs 7. Summary
Cationic and zwitterionic polymerizable surfactants bearing tri- and tetraethyleneglycol spacer groups between the polymerizable moiety and the surfactant structure were prepared and polymerized. Monomers and polymers were investigated with respect to their aggregation behavior in aqueous systems and compared to analogous monomers and polymers lacking spacer groups. In the case of the monomeric surfactants, the spacer groups depress both the Kraffttemperature and the critical micelle concentration. the area occupied per molecule at the air-water interface is substantially enlarged by the spacers, whereas the depression of surface tension is nearly constant. Although the monomers with and without spacers are true surfactants, all the polymers are water-insoluble, but form monomolecular layers at the air-water interface. In analogy to the monomer behavior, the incorporation of the spacer groups increases the area occupied per repeat unit at the air-water interface substantially, but hardly affects the surface activity.
Recent developments in the synthesis of polyelectrolytes are highlighted, with respect to the nature of the ionic groups, the polymer backbones, synthetic methods, and additional functionality given to the polyelectrolytes. In fact, the synthesis of new polyelectrolytes is mostly driven by material aspects, currently. The article pays particular attention to strong polyelectrolytes, and the new methods of controlled polymerization. These methods and the so-called click reactions have enabled novel designs of polyelectrolytes. Nevertheless, the polymerization of unprotected ionic monomers is still challenging and limits the synthetic possibilities. The structural aspects are complemented by considerations with respect to the aspired uses of the new polyelectrolytes.
The structures and synthesis of polyzwitterions ("polybetaines") are reviewed, emphasizing the literature of the past decade. Particular attention is given to the general challenges faced, and to successful strategies to obtain polymers with a true balance of permanent cationic and anionic groups, thus resulting in an overall zero charge. Also, the progress due to applying new methodologies from general polymer synthesis, such as controlled polymerization methods or the use of "click" chemical reactions is presented. Furthermore, the emerging topic of responsive ("smart") polyzwitterions is addressed. The considerations and critical discussions are illustrated by typical examples.
A series of dimeric cationic surfactants (gemini surfactants), which have spacer groups of varying length and flexibility, was synthesized. The series is derived from the parent compounds dodecyltrimethylammonium chloride or benzyldodecyldimethylammonium chloride. Characteristic surfactant properties of the dimeric ammonium compounds such as surface activity, micellization, viscosity effects, foaming, and solubilization, were studied with respect to the influence of the spacer group on the surfactant. For all properties, the influence of the length of the spacer group was predominant though the chemical nature of the spacer cannot be neglected
The functionalization of polyelectrolyte multilayers often implies the use of bulky functional fragments, attached to a standard polyelectrolyte matrix. Despite of the high density of non-charged, often hydrophobic substituents, regular film growth by sequential adsorption proceeds easily when an appropriate polyelectrolyte counter ion is chosen. However, the functional fragments may cluster or aggregate. This complication is particularly evident when using chromophores and fluorophores as bulky pendant groups. Attention has to be paid to this phenomenon for the design of functional polyelectrolyte films, as aggregation may modify crucially the properties. The use of charged spacer groups does not necessarily suppress the aggregation of functional side groups. Still, clustering and aggregation depend on the detailed system employed, and are not obligatory. In the case of cationic poly(acrylamide)s labeled with naphthalene and pyrene fluorophores, for instance, the polymers form intramolecular hydrophobic associates in solution, as indicated by strong excimer formation. But the polymers can undergo a conformational rearrangement upon adsorption so that they are decoiled in the adsorbed films. Analogous observations are made for polyanions bearing mesogenic biphenyls fragments. In contrast, polycations functionalized with the dye coumarin 343 show little aggregation in solution, but a marked aggregation in the ESA films
Mixed monolayers and Langmuir-Blodgett multilayers of functional low molecular weight guest compounds, especially nonlinear optical (NLO) dyes, within the matrix of an amphotropic spacer polymer have been prepared. The polymer matrix enabled the transfer of guest compounds not capable of self-organizing at the air-water interface by themselves. The structure of the LB multilayers and the transfer process were studied by small angle X-ray scattering and UV-visible spectroscopy. Good NLO coefficients were found in the mixed films.
The trithiocarbonate 2-(benzylsulfanylthiocarbonylsulfanyl) propanoic acid is formed as minor by-product in the synthesis of the dithioester 2-((2-phenylthioacetyl)sulfanyl) propanoic acid via the Grignard route. The mechanism for this side reaction is not clear. The isolated trithiocarbonate may act as unsymmetrical but bifunctional RAFT agent in the aqueous polymerization of N,N-dimethyl acrylamide. Therefore, it is important to separate it completely from the dithioester before engaging the latter in controlled free radical polymerization to guarantee a maximum control.
Amphiphilic derivatives of octadiene and docosadiene were investigated in monolayers and Langmuir-Blodgett multilayers, with respect to their self-organization and their polymerization behavior. All amphiphiles investigated form monolayers. However, only acid and alcohol derivatives were able to build up multilayers. Those multilayers are rapidly photopolymerized in the layers via a two-step process: Irradiation with long-wavelength UV light yields soluble polymers, whereas additional irradiation with sfiort-wavelength UV light produces insoluble and presumably cross-linked polymers. The reaction meclianism is discussed according to the polymer characterization by UV spectroscopy, small-angle X-ray scattering, NMR spectroscopy, and gel permeation chromatography. All multilayers undergo structural changes during the polymerization; substantial changes result in defects in the polymerized layers as observed by scanning electron microscopy. In contrast to the acids and alcohols, the deposition of monolayers of the aldehyde derivatives did not yield well-ordered multilayers, but rather amorphous films. In this different film structure, the photopolymerization process differs from the one observed in multilayers.
Langmuir-Blodgett multilayers of polymerizable carboxylic acids with hydrocarbon or fluorocarbon chains were prepared. The multilayers were polymerized by UV light and the reactions were studied by UV/visible spectroscopy. The polyreactions strongly influence the multilayer structures which were investigated by X-ray small-angle scattering and scanning electron microscopy. The spreading behaviour of the monomers, the preparation of multilayers, their reactivities in multilayers and structural effects caused by the polyreactions are discussed with regard to the hydrophilic head groups, the polymerizable groups and the hydrophobic chains.
Several polymerizable lipids were synthesized and polymerized to amphiphilic homopolymers and to copolymers with the help of hydrophilic comonomers. The self-organization of these polymeric lipids was investigated in monolayers and Langmuir-Blodgett multilayers. The self-organization of these polymers in model membranes is due to hydrophilic spacer groups in the amphiphilic side groups as well as to hydrophilic spacer groups in the polymer backbone. Thus, highly ordered monolayers and LB-multilayers are easily obtained.
Oriented supramolecular systems-polymeric monolayers and multilayers from prepolymerized amphiphiles
(1986)
Oriented polymeric membranes were originally prepared by polymerization or polycondensation of preoriented monomers. The introduction of hydrophilic spacer groups into the polymeric amphiphiles allowed the formation of highly ordered systems (monolayers, liposomes, multilayers) from prepolymerized amphiphiles: due to the partial decoupling of the different mobilities and orientation tendencies of the polymer chain and the amphiphilic side groups, these polymers are able to self-organize. In monolayer experiments the high order of these membranes could be demonstrated by their surface pressure area-diagrams. In addition the combination of order and mobility of these spacer groups containing polymeric amphiphiles allowed the formation of Langmuir-Blodgett-multilyers with a high layer correlation. Thus, disturbancies in highly oriented layers can be avoided normally taking place during the polymerization reaction (e.g. contractions) or oriented monomeric layers.
The widespread occurrence of zwitterionic compounds in nature has incited their frequent use in designing biomimetic materials. Therefore, zwitterionic polymers are a thriving field. A particular interest for this particular polymer class has currently focused on their use in establishing neutral, low-fouling surfaces. After highlighting strategies to prepare model zwitterionic surfaces as well as those that are more suitable for practical purposes relying strongly on radical polymerization methods, we present recent efforts to diversify the structure of the hitherto quite limited variety of zwitterionic monomers and of the derived polymers. We identify key structural variables, consider their influence on essential properties such as overall hydrophilicity and long-term stability, and discuss promising targets for the synthesis of new variants.
Three series of new oligomeric cationic surfactants were synthesized. These amphiphiles are trimeric and tetrameric oligomeric quaternary ammonium chlorides, with spacer groups of different lengths separating the individual surfactant fragments. The properties of the compounds, such as Krafft temperatures, surface activity, micellization, viscosifying effects, foaming and solubilizing capacity, are studied. The influence of the degree of oligomerization and of the spacer group on the surfactant properties is discussed, in comparison with the analogous standard monomeric and dimeric ("gemini") surfactants. Typically, the evolution of the properties observed from standard to dimeric surfactants progresses with the trimers and tetramers, resulting for instance in extremely low critical micellization concentrations
Equilibrium surface tension (se) versus concentration isotherms of surface-chemically pure aqueous solutions of the homologous series of N-n-alkyl-4'-(dimethylamino)-stilbaziumbromides ('hemicyanines') were measured at 295 K. The adsorption parameters of saturation adsorption and standard free energy of adsorption of the hemicyanines were determined from the evaluation of the se vs. c isotherms by using a two state approach to surface equation of state. The adsorption parameters reveal a very pronounced phenomenon of alternation (even/ odd- effect) which has so far not been met to a large extent like this. Thus, the cross-sectional areas of the odd members are almost twice those of the related even members. Surface activity of the odd is stronger than that of the even members. UV-Vis investigations showed that there is no indication of aggregate formation in the adsorption layer. The thermodynamic results give evidence for distinct differences between the surface conformations of the even- and the odd-chain hemicyanine dyes although the reasons for it are not known.
Multicompartment micelles are complex nanosized systems that possess a hydrosoluble shell and a hydrophobic core, which is characterized by segregated incompatible subdomains. With roots starting about ten years ago, the field of multi compartment micelles has evolved slowly, until recently when significant achievements have been made. The present article reviews strategies for building such micellar assemblies as well as morphological studies, highlights the future challenges, and discusses possible applications, which exploit the coexistence of differentiated nano- domains. Formation of multi compartment micelles using miktoarm stars mu-(polyethylethylene)(poly(ethylene oxide))(poly(perfluoropropylene oxide)) and a cryo-TEM image visualizing the process
A novel method to prepare ultrathin, freestanding polyelectrolyte films in pores, without the need of sacrificial precursor coatings, has been developed (see Figure). The freestanding films are stable under ambient conditions and suited for additional electrostatic self-assembly or surface modification. They can be specifically decomposed, whereas after thermal crosslinking, resistant films are obtained
Citrate-capped gold nanoparticles as well as planar gold surfaces can be efficiently grafted with a covalently attached polymer monolayer a few nanometers thick, by simple contact of the metal surface with dilute aqueous solutions of hydrophilic polymers that are end-capped with disulfide moieties, as shown by UV/vis absorption, dynamic light scattering, and surface plasmon resonance studies. The hydrophilic polymer-coated gold colloids can be freeze-dried and stored as powders that can be subsequently dissolved to yield stable aqueous dispersions, even at very large concentrations. They allow for applying filtrations, gel permeation chromatography, or centrifugation. They do not suffer from undesirable nonspecific adsorption of proteins while allowing the diffusion of small species within the hydrogel surface coating. In addition, specific properties of the original hydrophilic polymers are retained such as a lower critical solution temperature. The latter feature could be useful to enhance optical responses of functionalized gold surfaces toward interaction with various substrates.
Amphiphilic linear ternary block copolymers (ABC) were synthesized in three consecutive steps by the reversible addition fragmentation chain transfer (RAFT) method. Using oligo(ethylene oxide) monomethyl ether acrylate, benzyl acrylate, and 1H,1H-perfluorobutyl acrylate monomers, the triblock copolymers consist of a hydrophilic (A), a lipophilic (B), and a fluorophilic (C) block. The block sequence of the triphilic copolymers was varied systematically to provide all possible variations: ABC, ACB, and BAC. All blocks have glass transition temperatures below 0 degrees C. Self-assembly into spherical micellar aggregates was observed in aqueous solution, where hydrophobic cores undergo local phase separation into various ultrastructures as shown by cryogenic transmission electron microscopy (cryo-TEM). Selective solubilization of substantial quantities of hydrocarbon and fluorocarbon low molar mass compounds by the lipophilic and fluorophilic block, respectively, is demonstrated.
An amphiphilic linear ternary block copolymer was synthesised in three consecutive steps via reversible addition-fragmentation chain transfer polymerisation. Oligo(ethylene glycol) monomethyl ether acrylate was engaged as a hydrophilic building block, while benzyl acrylate and 3-tris(trimethylsiloxy)silyl propyl acrylate served as hydrophobic building blocks. The resulting "triphilic" copolymer consists thus of a hydrophilic (A) and two mutually incompatible "soft" hydrophobic blocks, namely, a lipophilic (B) and a silicone-based (C) block, with all blocks having glass transition temperatures well below 0 A degrees C. The triphilic copolymer self-assembles into spherical multicompartment micellar aggregates in aqueous solution, where the two hydrophobic blocks undergo local phase separation into various ultrastructures as evidenced by cryogenic transmission electron microscopy. Thus, a silicone-based polymer block can replace the hitherto typically employed fluorocarbon-based hydrophobic blocks in triphilic block copolymers for inducing multicompartmentalisation.
A series of RAFT agents was synthesised, and used to prepare various ionic. non-ionic and zwitterionic water- soluble polymers, in organic as well as in aqueous media. The RAFT process proved to be a powerful method to prepare functional polymers of complex structure. such as amphiphilic diblock and triblock copolymers. This includes polymers containing one or even two stimuli-sensitive hydrophilic blocks. Switching the hydrophilic character of a single or of several blocks by changing the PH, the temperature or the salt content demonstrated the variability of the molecular designs suited for stimuli-sensitive polymeric amphiphiles, and exemplified the concept of multiple-sensitive systems. (c) 2005 Published by Elsevier Ltd
A series of nonionic, anionic, and cationic water-soluble monomers bearing the (meth)acrylate, (meth)acrylamide, or styrene moiety were polymerized in water by free-radical polymerization via reversible addition- fragmentation chain transfer (RAFT). Several new water-soluble RAFT agents based on dithiobenzoate were employed that are water soluble independently of the pH. One of them bears a fluorophore, enabling unsymmetrical double end-group labeling as well as the preparation of fluorescent-labeled polymers. The temperature-dependent stability of the new RAFT agents against hydrolysis was studied. Controlled polymerization in aqueous solution was possible with styrenic, acrylic, and methacrylic monomers; molar masses increase with conversion, and polydispersities are relatively low. But RAFT polymerization failed for an anionic itaconate. Whereas polymerizations of methacrylamides were slow at temperatures below 60 degrees C, such conditions proved favorable for the RAFT polymerization of acrylates and methacrylates, to minimize hydrolysis of the dithioester end-group functionality, and to improve the preparation of block copolymers
The non-ionic monomer (methoxy diethylene glycol) acrylate is copolymerized with its azodye-functionalized acrylate analogue using reversible addition-fragmentation chain transfer (RAFT) polymerization. Copolymerization is increasingly difficult with increasing amounts of the azo-dye-bearing monomer. The resulting water-soluble polymers are thermosensitive, exhibiting lower critical solution temperature (LCST) behavior, which can be modulated by the photoinduced trans-cis isomerization of the dye. While already small contents of the hydrophobic azobenzene group reduce the phase-transition temperatures of the copolymers strongly, photoisomerization of the apolar trans-state to the more-polar cis-state has only a small effect, and decreases rather than increases the cloud points.
The easily accessible, but virtually overlooked monomer methoxy diethylene glycol acrylate was polymerized by the RAFT method using monofunctional, difunctional, and trifunctional trithiocarbonates to afford thermoresponsive polymers exhibiting lower critical solution temperature-type phase transitions in aqueous solution. The use of the appropriate RAFT agent allowed for the preparation and systematic variation of polymers with defined molar mass, end-groups, and architecture, including amphiphilic diblock, symmetrical triblock, and triarm star-block copolymers, containing polystyrene as permanently hydrophobic constituent. The cloud points (CPs) of the various polymers proved to be sensitive to all varied parameters, namely molar mass, nature, and number of the end-groups, and the architecture, up to relatively high molar masses. Thus, CPs of the polymers can be adjusted within the physiological interesting range of 2040 degrees C. Remarkably, CPs increased with the molar mass, even when hydrophilic end groups were attached to the polymers.
A series of symmetrical, thermo-responsive triblock copolymers was prepared by reversible addition fragmentation chain transfer (RAFT) polymerization, and studied in aqueous solution with respect to their ability to form hydrogels. Triblock copolymers were composed of two identical, permanently hydrophobic outer blocks, made of low molar mass polystyrene, and of a hydrophilic inner block of variable length, consisting of poly(methoxy diethylene glycol acrylate) PMDEGA. The polymers exhibited a LCST-type phase transition in the range of 20-40 degrees C, which markedly depended on molar mass and concentration. Accordingly, the triblock copolymers behaved as amphiphiles at low temperatures, but became water-insoluble at high temperatures. The temperature dependent self-assembly of the amphiphilic block copolymers in aqueous solution was studied by turbidimetry and rheology at concentrations up to 30 wt %, to elucidate the impact of the inner thermoresponsive block on the gel properties. Additionally, small-angle X-ray scattering (SAXS) was performed to access the structural changes in the gel with temperature. For all polymers a gel phase was obtained at low temperatures, which underwent a gel-sol transition at intermediate temperatures, well below the cloud point where phase separation occurred. With increasing length of the PMDEGA inner block, the gel-sol transition shifts to markedly lower concentrations, as well as to higher transition temperatures. For the longest PMDEGA block studied (DPn about 450), gels had already formed at 3.5 wt % at low temperatures. The gel-sol transition of the hydrogels and the LCST-type phase transition of the hydrophilic inner block were found to be independent of each other.
Polyelectrolytes in dilute solutions (0.01 mmol/L) adsorb in a two-dimensional lamellar phase to oppositely charged lipid monolayers at the air/water interface. The interchain separation is monitored by Grazing Incidence X-ray Diffraction. On monolayer compression, the interchain separation decreases to a factor of two. To investigate the influence of the electrostatic interaction, either the line charge density of the polymer is reduced (a statistic copolymer with 90% and 50% charged monomers) or mixtures between charged and uncharged lipids are used (dipalmitoylphosphatidylcholine (DPPC)/dioctadecyldimethylammonium bromide (DODAB)) On decrease of the surface charge density, the interchain separation increases, while on decrease of the linear charge density, the interchain separation decreases. The ratio between charged monomers and charged lipid molecules is fairly constant; it decreases up to 30% when the lipids are in the fluid phase. With decreasing surface charge or linear charge density, the correlation length of the lamellar order decreases.
The aggregation behavior of catanionics formed by the mixture of cationic geminis derived from dodecyltrimethylammonium chloride (DTAC) and anionic sodium dodecylsulfate (SDS) was studied by means of phase studies and comprehensive small-angle neutron scattering (SANS) experiments at 25 degrees C and 50 mM overall concentration. The results are compared to those for the previously studied SDS + DTAC system. Various gemini spacers of different natures and geometries were used, but all of them had similar lengths: an ethoxy bridge, a double bond, and an aromatic ring binding the two DTACs in three different substitutions (ortho, meta, and para). SANS and SAXS data analysis indicates that the spacer has no large effect on the spheroidal micelles of pure surfactants formed at low concentration in water; however, specific effects appear with the addition of electrolytes. Microstructures formed in the catanionic mixtures are rather strongly dependent on the nature of the spacer. The most important finding is that for the hydrophilic, flexible ethoxy bridge, monodisperse vesicles with a fixed anionic/cationic charge ratio (depending only on the surfactant in excess) are formed. Furthermore, the composition of these vesicles shows that strongly charged aggregates are formed. This study therefore provides new opportunities for developing tailor-made gemini surfactants that allow for the fine tuning of catanionic structures.
Effect of magnesium salts with chaotropic anions on the swelling behavior of PNIPMAM thin films
(2023)
Poly(N-isopropylmethacrylamide) (PNIPMAM) is a stimuli responsive polymer, which in thin film geometry exhibits a volume-phase transition upon temperature increase in water vapor. The swelling behavior of PNIPMAM thin films containing magnesium salts in water vapor is investigated in view of their potential application as nanodevices. Both the extent and the kinetics of the swelling ratio as well as the water content are probed with in situ time-of-flight neutron reflectometry. Additionally, in situ Fourier-transform infrared (FTIR) spectroscopy provides information about the local solvation of the specific functional groups, while two-dimensional FTIR correlation analysis further elucidates the temporal sequence of solvation events. The addition of Mg(ClO4)2 or Mg(NO3)2 enhances the sensitivity of the polymer and therefore the responsiveness of switches and sensors based on PNIPMAM thin films. It is found that Mg(NO3)2 leads to a higher relative water uptake and therefore achieves the highest thickness gain in the swollen state.
Dielectric spectroscopy is employed to analyze the molecular dynamics and the charge transport in mixtures of zwitterionic polymers of the type poly{3 [N(-methacryloyloxyalkyl)] N, [N-dimethylammonio propanesulfonate] with sodium iodide in the frequency range of 10²Hz-10(up)7 Hz and in the temperature range of 110 K-400 K. The amount of inorganic salt added varies from 0-200 mol-% relative to the number of zwitterionic groups present in the polymer, contributing strongly to the conductivity. One relaxation process is observed whose relaxation rate depends strongly on the length of the aliphatic spacer between the polymethacrylate main chain and the zwitterionic group. Exhibiting an Arrhenius-like temperature depence with activation energy EA = 47 KJ/mol, this relaxation process is assigned to fluctuation of the quaternary ammonium groups in the side chains. At higher temperatures, the dielectric properties and the conductivity are primarily dominated by the mobile inorganic ions: conductivity strongly depends on the salt concentration, showing a pronounced electrode polarization effect. The frequency and salt concentration, dependences of the conductivity can be quantitatively described as hopping of charge carriers being subject to spatially randomly varying energy barriers. For the low-frequency regime and for the critical frequency marking the onset of the conductivity's dispersion, the Barton-Nakajima-Namikawa (BNN) relationship is fulfilled.
A new precursor route for the preparation of bulk oxides and thin films of bismuth vanadates is proposed. The method involves the thermal treatment under air and mild conditions of hybrid organic-inorganic precursors, made from a zwitterionic salt-free polymer matrix and selected inorganic species. Monoclinic BiVO4 was obtained in the form of bulk oxide by calcination of the powdered homogeneous hybrid materials at 600 degrees C, from precursors containing Bi and V in stoichiometric amounts. In the same way, thermodiffractometry studies performed on a hybrid material exhibiting a Bi/ V molar ratio of 2 revealed that the ionic conductor gamma-Bi4V2O11 phase can be stabilized under very soft thermal conditions (300 degrees C). Additionally, thin films of yellow monoclinic BiVO4 were for the first time fabricated, by thermal treatment of the same hybrid polymeric precursors deposited on quartz substrates by spin coating, using a layer- by-layer technique. The presence of the target phase at the surface of the plates was confirmed by X-ray diffraction as well as UV-vis measurements
Homopolymers were prepared from diallylammonium monomers bearing 4-methylcoumarin and 4-cyanobiphenyl as fluorescent and mesogenic side groups, as well as their copolymers with diallyldimethylammonium chloride (DADMAC). Organic-inorganic hybrid films were electrostatically self-assembled via the layer-by-layer technique on silicon wafers and quartz plates from the chromophore-bearing polymers and an exfoliated synthetic hectorite. Photophysical studies performed in solution as well as in the self-assembled films demonstrated only a weak tendency for aggregation of the chromophores in the macromolecules. Moreover, assemblies made from the polymers carrying the cyanobiphenyl mesogen were found to exhibit a pronounced internal order
Hydrophobically substituted diallylamines bearing a hexyl, dodecyl, or octadecyl chain were synthesized and homopolymerized as hydrochlorides. Copolymerixation of the diallylamines with maleic acid produces alternating copolymers. The copolymers behave as amphiphilic polyampholytes and dissolve best in the acidic or in the basic form. Only the colpolymer with the hexyl chain could be dissolved in aqueous solvents and shows hydrophobic associaiton. The copolymers with the longer alkyl chains require polar protic organic solvents. All polymers are amorphous, but show a superstructure in bulk due to their amphiphilicity
The impact of the orientation of zwitterionic groups, with respect to the polymer backbone, on the antifouling performance of thin hydrogel films made of polyzwitterions is explored. In an extension of the recent discussion about differences in the behavior of polymeric phosphatidylcholines and choline phosphates, a quasi-isomeric set of three poly(sulfobetaine methacrylate)s is designed for this purpose. The design is based on the established monomer 3-[N-2-(methacryloyloxy)ethyl-N,N-dimethyl]ammonio-propane-1-sulfonate and two novel sulfobetaine methacrylates, in which the positions of the cationic and the ionic groups relative to the polymerizable group, and thus also to the polymer backbone, are altered. The effect of the varied segmental dipole orientation on their water solubility, wetting behavior by water, and fouling resistance is compared. As model systems, the adsorption of the model proteins bovine serum albumin (BSA), fibrinogen, and lysozyme onto films of the various polyzwitterion surfaces is studied, as well as the settlement of a diatom (Navicula perminuta) and barnacle cyprids (Balanus improvisus) as representatives of typical marine fouling communities. The results demonstrate the important role of the zwitterionic group's orientation on the polymer behavior and fouling resistance
The impact of the orientation of zwitterionic groups, with respect to the polymer backbone, on the antifouling performance of thin hydrogel films made of polyzwitterions is explored. In an extension of the recent discussion about differences in the behavior of polymeric phosphatidylcholines and choline phosphates, a quasi-isomeric set of three poly(sulfobetaine methacrylate)s is designed for this purpose. The design is based on the established monomer 3-[N-2-(methacryloyloxy)ethyl-N,N-dimethyl]ammonio-propane-1-sulfonate and two novel sulfobetaine methacrylates, in which the positions of the cationic and the ionic groups relative to the polymerizable group, and thus also to the polymer backbone, are altered. The effect of the varied segmental dipole orientation on their water solubility, wetting behavior by water, and fouling resistance is compared. As model systems, the adsorption of the model proteins bovine serum albumin (BSA), fibrinogen, and lysozyme onto films of the various polyzwitterion surfaces is studied, as well as the settlement of a diatom (Navicula perminuta) and barnacle cyprids (Balanus improvisus) as representatives of typical marine fouling communities. The results demonstrate the important role of the zwitterionic group's orientation on the polymer behavior and fouling resistance.
Combining high hydrophilicity with charge neutrality, polyzwitterions are intensely explored for their high biocompatibility and low-fouling properties. Recent reports indicated that in addition to charge neutrality, the zwitterion's segmental dipole orientation is an important factor for interacting with the environment. Accordingly, a series of polysulfobetaines with a novel architecture was designed, in which the cationic and anionic groups of the zwitterionic moiety are placed at equal distances from the backbone. They were investigated by in vitro biofouling assays, covering proteins of different charges and model marine organisms. All polyzwitterion coatings reduced the fouling effectively compared to model polymer surfaces of poly(butyl methacrylate), with a nearly equally good performance as the reference polybetaine poly(3-(N-(2-(methacryloyloxy)ethyl)-N,N-dimethylammonio)propanesulfonate). The specific fouling resistance depended on the detailed chemical structure of the polyzwitterions. Still, while clearly affecting the performance, the precise dipole orientation of the sulfobetaine group in the polyzwitterions seems overall to be only of secondary importance for their antifouling behavior.
The hydrolytic stability of polymers to be used for coatings in aqueous environments, for example, to confer anti-fouling properties, is crucial. However, long-term exposure studies on such polymers are virtually missing. In this context, we synthesized a set of nine polymers that are typically used for low-fouling coatings, comprising the well-established poly(oligoethylene glycol methylether methacrylate), poly(3-(N-2-methacryloylethyl-N,N-dimethyl) ammoniopropanesulfonate) (“sulfobetaine methacrylate”), and poly(3-(N-3-methacryamidopropyl-N,N-dimethyl)ammoniopropanesulfonate) (“sulfobetaine methacrylamide”) as well as a series of hitherto rarely studied polysulfabetaines, which had been suggested to be particularly hydrolysis-stable. Hydrolysis resistance upon extended storage in aqueous solution is followed by ¹H NMR at ambient temperature in various pH regimes. Whereas the monomers suffered slow (in PBS) to very fast hydrolysis (in 1 M NaOH), the polymers, including the polymethacrylates, proved to be highly stable. No degradation of the carboxyl ester or amide was observed after one year in PBS, 1 M HCl, or in sodium carbonate buffer of pH 10. This demonstrates their basic suitability for anti-fouling applications. Poly(sulfobetaine methacrylamide) proved even to be stable for one year in 1 M NaOH without any signs of degradation. The stability is ascribed to a steric shielding effect. The hemisulfate group in the polysulfabetaines, however, was found to be partially labile.
Linear amphiphilic diblock and ternary triblock copolymers were synthesized by the RAFT method in two successive steps using a poly(ethylene oxide) (PEO) macrochain transfer agent, butyl or 2-ethylhexyl acrylate, and 1H, 1H, 2H, 2H-perfluorodecyl acrylate. The diblock and the triblock copolymers, which consist of a hydrophilic, a lipophilic, and a short fluorophilic block, self-assemble in water into spherical micellar aggregates. Imaging by cryogenic transmission electron microscopy (cryo-TEM) revealed that the micellar cores of the aggregates made from these "triphilic" copolymers can undergo local phase separation to form a unique ultrastructure. In these multicompartment micelles, it appears that extended nonspherical domains, presumably made of nanocrystallites of the fluorocarbon block, are embedded in the hydrocarbon matrix forming the spherical micellar core. This novel internal structure of a micellar core is attributed to the mutual incompatibility of the fluorocarbon and hydrocarbon side chains in combination with the tendency of the used fluorocarbon acrylate monomer to undergo side-chain crystallization.
Examining the UV-vis absorption of RAFT chain transfer agents and their use for polymer analysis
(2011)
The absorption characteristics of a large set of thiocarbonyl based chain transfer agents (CTAs) were studied by UV-vis spectroscopy in order to identify appropriate conditions for exploiting their absorbance bands in end-group analysis of polymers prepared by reversible addition-fragmentation chain transfer (RAFT) polymerisation. Substitution pattern and solvent polarity were found to affect notably the wavelengths and intensities of the pi-pi*- and n-pi*-transition of the thiocarbonyl bond of dithioester and trithiocarbonate RAFT agents. Therefore, it is advisable to refer in end group analysis to the spectral parameters of low molar mass analogues of the active polymer chain ends, rather than to rely on the specific RAFT agent engaged in the polymerisation. When using appropriate conditions, the quantification of the thiocarbonyl end-groups via the pi-pi* band of the thiocarbonyl moiety around 300-310 nm allows a facile, sensitive and surprisingly precise estimation of the number average molar mass of the polymers produced, without the need of particular end group labels. Moreover, when additional methods for absolute molar mass determination can be applied, the quantification of the thiocarbonyl end-groups by UV-spectroscopy provides a good estimate of the degree of active end group for a given polymer sample.
Linear amphiphilic diblock and ternary triblock copolymers were synthesized by the RAFT method in three Successive Steps, using oligo(ethylene oxide) monomethyl ether acrylate, butyl or 2-ethylhexyl acrylate, and 1H, 1H, 2H, 2H-perfluorodecyl acrylate. The diblock and the triblock copolymers, which consist of a hydrophilic, a lipophilic, and a fluorophilic block, self-assemble in water into spherical micellar aggregates. Imaging by cryogenic transmission electron microscopy (cryo-TEM) revealed that the cores of the micellar aggregates made from these "triphilic" copolymers undergo local phase separation to form various ultrastructures, which depend sensitivity on the given block sequence. While the sequence hydrophilic-lipophilic-fluorophilic resulted in multicompartment cores with core-shell-corona morphology, the sequence lipophilic-hydrophilic-fluorophilic provided new "patched double micelle" and larger "soccer ball" structures.