Refine
Has Fulltext
- yes (2) (remove)
Document Type
- Doctoral Thesis (2) (remove)
Is part of the Bibliography
- yes (2)
Keywords
- Elastizitätsmodul (2) (remove)
Institute
The thesis comprises three experimental studies, which were carried out to unravel the short- as well as the long-term mechanical properties of shale rocks. Short-term mechanical properties such as compressive strength and Young’s modulus were taken from recorded stress-strain curves of constant strain rate tests. Long-term mechanical properties are represented by the time– dependent creep behavior of shales. This was obtained from constant stress experiments, where the test duration ranged from a couple minutes up to two weeks. A profound knowledge of the mechanical behavior of shales is crucial to reliably estimate the potential of a shale reservoir for an economical and sustainable extraction of hydrocarbons (HC). In addition, healing of clay-rich forming cap rocks involving creep and compaction is important for underground storage of carbon dioxide and nuclear waste.
Chapter 1 introduces general aspects of the research topic at hand and highlights the motivation for conducting this study. At present, a shift from energy recovered from conventional resources e.g., coal towards energy provided by renewable resources such as wind or water is a big challenge. Gas recovered from unconventional reservoirs (shale plays) is considered a potential bridge technology.
In Chapter 2, short-term mechanical properties of two European mature shale rocks are presented, which were determined from constant strain rate experiments performed at ambient and in situ deformation conditions (confining pressure, pc ≤ 100 MPa, temperature, T ≤ 125 °C, representing pc, T - conditions at < 4 km depth) using a Paterson– type gas deformation apparatus. The investigated shales were mainly from drill core material of Posidonia (Germany) shale and weathered material of Bowland (United Kingdom) shale. The results are compared with mechanical properties of North American shales. Triaxial compression tests performed perpendicular to bedding revealed semibrittle deformation behavior of Posidonia shale with pronounced inelastic deformation. This is in contrast to Bowland shale samples that deformed brittle and displayed predominantly elastic deformation. The static Young’s modulus, E, and triaxial compressive strength, σTCS, determined from recorded stress-strain curves strongly depended on the applied confining pressure and sample composition, whereas the influence of temperature and strain rate on E and σTCS was minor. Shales with larger amounts of weak minerals (clay, mica, total organic carbon) yielded decreasing E and σTCS. This may be related to a shift from deformation supported by a load-bearing framework of hard phases (e.g., quartz) towards deformation of interconnected weak minerals, particularly for higher fractions of about 25 – 30 vol% weak phases. Comparing mechanical properties determined at reservoir conditions with mechanical data applying effective medium theories revealed that E and σTCS of Posidonia and Bowland shale are close to the lower (Reuss) bound. Brittleness B is often quoted as a measure indicating the response of a shale formation to stimulation and economic production. The brittleness, B, of Posidonia and Bowland shale, estimated from E, is in good agreement with the experimental results. This correlation may be useful to predict B from sonic logs, from which the (dynamic) Young’s modulus can be retrieved.
Chapter 3 presents a study of the long-term creep properties of an immature Posidonia shale. Constant stress experiments (σ = const.) were performed at elevated confining pressures (pc = 50 – 200 MPa) and temperatures (T = 50 – 200 °C) to simulate reservoir pc, T - conditions. The Posidonia shale samples were acquired from a quarry in South Germany. At stresses below ≈ 84 % compressive strength of Posidonia shale, at high temperature and low confining pressure, samples showed pronounced transient (primary) creep with high deformation rates in the semibrittle regime. Sample deformation was mainly accommodated by creep of weak sample constituents and pore space reduction. An empirical power law relation between strain and time, which also accounts for the influence of pc, T and σ on creep strain was formulated to describe the primary creep phase. Extrapolation of the results to a creep period of several years, which is the typical time interval for a large production decline, suggest that fracture closure is unlikely at low stresses. At high stresses as expected for example at the contact between the fracture surfaces and proppants added during stimulation measures, subcritical crack growth may lead to secondary and tertiary creep. An empirical power law is suggested to describe secondary creep of shale rocks as a function of stress, pressure and temperature. The predicted closure rates agree with typical production decline curves recorded during the extraction of hydrocarbons. At the investigated conditions, the creep behavior of Posidonia shale was found to correlate with brittleness, calculated from sample composition.
In Chapter 4 the creep properties of mature Posidonia and Bowland shales are presented. The observed long-term creep behavior is compared to the short-term behavior determined in Chapter 2. Creep experiments were performed at simulated reservoir conditions of pc = 50 – 115 MPa and T = 75 – 150 °C. Similar to the mechanical response of immature Posidonia shale samples investigated in Chapter 3, creep strain rates of mature Bowland and Posidonia shales were enhanced with increasing stress and temperature and decreasing confining pressures. Depending on applied deformation conditions, samples displayed either only a primary (decelerating) or in addition also a secondary (quasi-steady state) and subsequently a tertiary (accelerating) creep phase before failure. At the same deformation conditions, creep strain of Posidonia shale, which is rich in weak constituents, is tremendously higher than of quartz-rich Bowland shale. Typically, primary creep strain is again mostly accommodated by deformation of weak minerals and local pore space reduction. At the onset of tertiary creep most of the deformation was accommodated by micro crack growth. A power law was used to characterize the primary creep phase of Posidonia and Bowland shale. Primary creep strain of shale rocks is inversely correlated to triaxial compressive strength and brittleness, as described in Chapter 2.
Chapter 5 provides a synthesis of the experimental findings and summarizes the major results of the studies presented in Chapters 2 – 4 and potential applications in the Exploration & Production industry.
Chapter 6 gives a brief outlook on potential future experimental research that would help to further improve our understanding of processes leading to fracture closure involving proppant embedment in unconventional shale gas reservoirs. Such insights may allow to improve stimulation techniques aimed at maintaining economical extraction of hydrocarbons over several years.
Chemische und physikalische Eigenschaften von Polymeren können verschiedene Zelltypen unterschiedlich, z. B. hinsichtlich Adhärenz oder Funktionalität, beeinflussen. Die Elastizität eines Polymers beeinflusst vor allem, welche Zugkräfte eine Zelle gegenüber ihrem Substrat entwickeln kann. Das Zellverhalten wird dann über intrazelluläre Rückkopplungsmechanismen reguliert. Die Oberflächenladung und/oder Hydrophilie eines Polymers beeinflusst zunächst die Adsorption von Ionen, Proteinen und anderen Molekülen. Vor allem über die Zusammensetzung, Dichte und Konformation der adsorbierten Komponenten werden anschließend die Wechselwirkungen mit den Zellen vermittelt. Des Weiteren können verschiedene Zelltypen unterschiedliche membranassoziierte Proteine, Zucker und Lipide aufweisen, so dass Polymereigenschaften zellspezifische Effekte bewirken können. Für biotechnologische Anwendungen und für den Einsatz in der regenerativen Medizin gewinnen Polymere, die spezifische Zellreaktionen regulieren können, immer weiter an Bedeutung. Die Isolierung und Kultur von primären Keratinozyten ist noch immer anspruchsvoll und die adäquate Heilung von Hautwunden stellt eine fortwährende medizinische Herausforderung dar. Ein Polymer, das eine bevorzugte Adhärenz von Keratinozyten bei gleichzeitig verminderter Anheftung dermaler Fibroblasten ermöglicht, würde erhebliche Vorteile für den Einsatz in der Keratinozyten-Zellkultur und als Wundauflage bieten. Um den potentiell spezifischen Einfluss bestimmter Polymereigenschaften auf primäre humane Keratinozyten und dermale Fibroblasten zu untersuchen, wurde in der vorliegenden Arbeit ein Zellkultursystem für die Mono- und Cokultur beider Zelltypen entwickelt. Das Testsystem wurde als Screening konzipiert, um den Einfluss unterschiedlicher Polymereigenschaften in mehreren Abstufungen auf die Zellen zu untersuchen. Folgende Parameter wurden untersucht: 1. Vitalität und Dichte adhärenter und nicht-adhärierter Zellen, 2. Schädigung der Zellmembran, 3. selektive Adhärenz von Keratinozyten in Cokultur durch die spezifische immunzytochemische Färbung von Keratin14 und Vimentin. Für die Polymere mit variabler Elastizität wurden zusätzlich die Ablagerung extrazellulärer Matrixkomponenten und die Sekretion löslicher Faktoren durch die Zellen untersucht. Als Modellpolymere für die Variation der Elastizität wurden vernetzte Poly(n-butylacrylate) (cPnBA) verwendet, da deren Elastizität durch den Anteil des Vernetzers eingestellt werden kann. Auf dem weniger elastischen cPnBA zeigte sich in der Cokultur ein doppelt so hohes Verhältnis von Keratinozyten zu Fibroblasten wie auf dem elastischeren cPnBA, so dass ein leichter zellselektiver Effekt angenommen werden kann. Acrylnitril-basierte Copolymere wurden als Modellpolymere für die Variation der Oberflächenladung und Hydrophilie verwendet, da die Eigenschaften durch Art und molaren Anteil des Comonomers eingestellt werden können. Durch Variation des molaren Anteils der Comonomere mit positiver bzw. negativer Ladung, Methacrylsäure-2-aminoethylester-hydrochhlorid (AEMA) und N-3-Aminopropyl-methacrylamid-hydro-chlorid (APMA) bzw. Natriumsalz der 2-Methyl-2-propen-1-sulfonsäure (NaMAS), wurde der Anteil der positiven bzw. negativen Ladung im Copolymer variiert. Durch die Erhöhung des molaren Anteils des hydrophilen Comonomers N-Vinylpyrrolidon (NVP) wurde die Hydrophilie des Copolymers gesteigert. Die Erhöhung des molaren Anteils an positiv geladenem Comonomer AEMA im Copolymer führte tendenziell zu einer höheren Keratinozytendichte, wobei die Fibroblastendichte unverändert blieb. Durch die Erhöhung des molaren Anteils des positiv geladenen Comonomers APMA ergaben sich keine deutlichen Unterschiede in Dichte, Vitalität oder Selektivität der Zellen. Durch die stufenweise Erhöhung des molaren Anteils des negativ geladenen Comonomers NaMAS konnte, wie im Falle von AEMA, eine Tendenz zur verbesserten Keratinozytenadhärenz beobachtet werden. Die Steigerung der Hydrophilie der Copolymere führte sowohl für Keratinozyten als auch für Fibroblasten zu einer reduzierten Adhärenz und Vitalität. In der vorliegenden Doktorarbeit wurde ein Testverfahren etabliert, das die Untersuchung von primären humanen Keratinozyten und primären humanen Fibroblasten in Monokultur und Cokultur auf verschiedenen Polymeren ermöglicht. Die bisherigen Ergebnisse zeigen, dass sich durch die gezielte Modifizierung verschiedener Polymereigenschaften die Adhärenz und Vitalität beider Zelltypen beeinflussen lässt. Die Reduktion der Elastizität sowie die Erhöhung des molaren Anteils geladener Comonomere führten zu einer Zunahme der Keratinozytenadhärenz. Da die Fibroblasten unbeeinflusst blieben, zeigte sich für einige der untersuchten Polymere eine leichte Zellselektivität. Diese könnte durch die weitere Erhöhung der Steifigkeit oder des Anteils geladener Comonomere möglicherweise weiter gesteigert werden.