Refine
Has Fulltext
- yes (430) (remove)
Year of publication
Document Type
- Postprint (226)
- Doctoral Thesis (194)
- Habilitation Thesis (8)
- Monograph/Edited Volume (1)
- Master's Thesis (1)
Language
- English (430) (remove)
Keywords
- Nanopartikel (19)
- nanoparticles (15)
- Selbstorganisation (12)
- self-assembly (11)
- DNA origami (10)
- RAFT (7)
- thermoresponsive (7)
- Polymerchemie (6)
- Synthese (6)
- block copolymer (6)
Institute
- Institut für Chemie (430) (remove)
Conventional energy sources are diminishing and non-renewable, take million years to form and cause environmental degradation. In the 21st century, we have to aim at achieving sustainable, environmentally friendly and cheap energy supply by employing renewable energy technologies associated with portable energy storage devices. Lithium-ion batteries can repeatedly generate clean energy from stored materials and convert reversely electric into chemical energy. The performance of lithium-ion batteries depends intimately on the properties of their materials. Presently used battery electrodes are expensive to be produced; they offer limited energy storage possibility and are unsafe to be used in larger dimensions restraining the diversity of application, especially in hybrid electric vehicles (HEVs) and electric vehicles (EVs). This thesis presents a major progress in the development of LiFePO4 as a cathode material for lithium-ion batteries. Using simple procedure, a completely novel morphology has been synthesized (mesocrystals of LiFePO4) and excellent electrochemical behavior was recorded (nanostructured LiFePO4). The newly developed reactions for synthesis of LiFePO4 are single-step processes and are taking place in an autoclave at significantly lower temperature (200 deg. C) compared to the conventional solid-state method (multi-step and up to 800 deg. C). The use of inexpensive environmentally benign precursors offers a green manufacturing approach for a large scale production. These newly developed experimental procedures can also be extended to other phospho-olivine materials, such as LiCoPO4 and LiMnPO4. The material with the best electrochemical behavior (nanostructured LiFePO4 with carbon coating) was able to delive a stable 94% of the theoretically known capacity.
In the present thesis, the self-assembly of multi thermoresponsive block copolymers in dilute aqueous solution was investigated by a combination of turbidimetry, dynamic light scattering, TEM measurements, NMR as well as fluorescence spectroscopy. The successive conversion of such block copolymers from a hydrophilic into a hydrophobic state includes intermediate amphiphilic states with a variable hydrophilic-to-lipophilic balance. As a result, the self-organization is not following an all-or-none principle but a multistep aggregation in dilute solution was observed. The synthesis of double thermoresponsive diblock copolymers as well as triple thermoresponsive triblock copolymers was realized using twofold-TMS labeled RAFT agents which provide direct information about the average molar mass as well as residual end group functionality from a routine proton NMR spectrum. First a set of double thermosensitive diblock copolymers poly(N-n-propylacrylamide)-b-poly(N-ethylacrylamide) was synthesized which differed only in the relative size of the two blocks. Depending on the relative block lengths, different aggregation pathways were found. Furthermore, the complementary TMS-labeled end groups served as NMR-probes for the self-assembly of these diblock copolymers in dilute solution. Reversible, temperature sensitive peak splitting of the TMS-signals in NMR spectroscopy was indicative for the formation of mixed star-/flower-like micelles in some cases. Moreover, triple thermoresponsive triblock copolymers from poly(N-n-propylacrylamide) (A), poly(methoxydiethylene glycol acrylate) (B) and poly(N-ethylacrylamide) (C) were obtained from sequential RAFT polymerization in all possible block sequences (ABC, BAC, ACB). Their self-organization behavior in dilute aqueous solution was found to be rather complex and dependent on the positioning of the different blocks within the terpolymers. Especially the localization of the low-LCST block (A) had a large influence on the aggregation behavior. Above the first cloud point, aggregates were only observed when the A block was located at one terminus. Once placed in the middle, unimolecular micelles were observed which showed aggregation only above the second phase transition temperature of the B block. Carrier abilities of such triple thermosensitive triblock copolymers tested in fluorescence spectroscopy, using the solvatochromic dye Nile Red, suggested that the hydrophobic probe is less efficiently incorporated by the polymer with the BAC sequence as compared to ABC or ACB polymers above the first phase transition temperature. In addition, due to the problem of increasing loss of end group functionality during the subsequent polymerization steps, a novel concept for the one-step synthesis of multi thermoresponsive block copolymers was developed. This allowed to synthesize double thermoresponsive di- and triblock copolymers in a single polymerization step. The copolymerization of different N-substituted maleimides with a thermosensitive styrene derivative (4-vinylbenzyl methoxytetrakis(oxyethylene) ether) led to alternating copolymers with variable LCST. Consequently, an excess of this styrene-based monomer allowed the synthesis of double thermoresponsive tapered block copolymers in a single polymerization step.
Nanoporous carbon materials are widely used in industry as adsorbents or catalyst supports, whilst becoming increasingly critical to the developing fields of energy storage / generation or separation technologies. In this thesis, the combined use of carbohydrate hydrothermal carbonisation (HTC) and templating strategies is demonstrated as an efficient route to nanostructured carbonaceous materials. HTC is an aqueous-phase, low-temperature (e.g. 130 – 200 °C) carbonisation, which proceeds via dehydration / poly-condensation of carbon precursors (e.g. carbohydrates and their derivatives), allowing facile access to highly functional carbonaceous materials. Whilst possessing utile, modifiable surface functional groups (e.g. -OH and -C=O-containing moieties), materials synthesised via HTC typically present limited accessible surface area or pore volume. Therefore, this thesis focuses on the development of fabrication routes to HTC materials which present enhanced textural properties and well-defined porosity. In the first discussed synthesis, a combined hard templating / HTC route was investigated using a range of sacrificial inorganic templates (e.g. mesoporous silica beads and macroporous alumina membranes (AAO)). Via pore impregnation of mesoporous silica beads with a biomass-derived carbon source (e.g. 2-furaldehyde) and subsequent HTC at 180 oC, an inorganic / carbonaceous hybrid material was produced. Removal of the template component by acid etching revealed the replication of the silica into mesoporous carbonaceous spheres (particle size ~ 5 μm), representing the inverse morphological structure of the original inorganic body. Surface analysis (e.g. FTIR) indicated a material decorated with hydrophilic (oxygenated) functional groups. Further thermal treatment at increasingly elevated temperatures (e.g. at 350, 550, 750 oC) under inert atmosphere allowed manipulation of functionalities from polar hydrophilic to increasingly non-polar / hydrophobic structural motifs (e.g. extension of the aromatic / pseudo-graphitic nature), thus demonstrating a process capable of simultaneous control of nanostructure and surface / bulk chemistry. As an extension of this approach, carbonaceous tubular nanostructures with controlled surface functionality were synthesised by the nanocasting of uniform, linear macropores of an AAO template (~ 200 nm). In this example, material porosity could be controlled, showing increasingly microporous tube wall features as post carbonisation temperature increased. Additionally, by taking advantage of modifiable surface groups, the introduction of useful polymeric moieties (i.e. grafting of thermoresponsive poly(N-isopropylacrylamide)) was also demonstrated, potentially enabling application of these interesting tubular structures in the fields of biotechnology (e.g. enzyme immobilization) and medicine (e.g. as drug micro-containers). Complimentary to these hard templating routes, a combined HTC / soft templating route for the direct synthesis of ordered porous carbonaceous materials was also developed. After selection of structural directing agents and optimisation of synthesis composition, the F127 triblock copolymer (i.e. ethylene oxide (EO)106 propylene oxide (PO)70 ethylene oxide (EO)106) / D-Fructose system was extensively studied. D-Fructose was found to be a useful carbon precursor as the HTC process could be performed at 130 oC, thus allowing access to stable micellular phase. Thermolytic template removal from the synthesised ordered copolymer / carbon composite yielded functional cuboctahedron single crystalline-like particles (~ 5 μm) with well ordered pore structure of a near perfect cubic Im3m symmetry. N2 sorption analysis revealed a predominantly microporous carbonaceous material (i.e. Type I isotherm, SBET = 257 m2g-1, 79 % microporosity) possessing a pore size of ca. 0.9 nm. The addition of a simple pore swelling additive (e.g. trimethylbenzene (TMB)) to this system was found to direct pore size into the mesopore size domain (i.e. Type IV isotherm, SBET = 116 m2g-1, 60 % mesoporosity) generating pore size of ca. 4 nm. It is proposed that in both cases as HTC proceeds to generate a polyfuran-like network, the organised block copolymer micellular phase is essentially “templated”, either via hydrogen bonding between hydrophilic poly(EO) moiety and the carbohydrate or via hydrophobic interaction between hydrophobic poly(PO) moiety and forming polyfuran-like network, whilst the additive TMB presumably interact with poly(PO) moieties, thus swelling the hydrophobic region expanding the micelle template size further into the mesopore range.
Towards greener stationary phases : thermoresponsive and carbonaceous chromatographic supports
(2011)
Polymers which are sensitive towards external physical, chemical and electrical stimuli are termed as ‘intelligent materials’ and are widely used in medical and engineering applications. Presently, polymers which can undergo a physical change when heat is applied at a certain temperature (cloud point) in water are well-studied for this property in areas of separation chemistry, gene and drug delivery and as surface modifiers. One example of such a polymer is the poly (N-isopropylacrylamide) PNIPAAM, where it is dissolved well in water below 32 oC, while by increasing the temperature further leads to its precipitation. In this work, an alternative polymer poly (2-(2-methoxy ethoxy)ethyl methacrylate-co- oligo(ethylene glycol) methacrylate) (P(MEO2MA-co-OEGMA)) is studied due to its biocompatibility and the ability to vary its cloud points in water. When a layer of temperature responsive polymer was attached to a single continuous porous piece of silica-based material known as a monolith, the thermoresponsive characteristic was transferred to the column surfaces. The hybrid material was demonstrated to act as a simple temperature ‘switch’ in the separation of a mixture of five steroids under water. Different analytes were observed to be separated under varying column temperatures. Furthermore, more complex biochemical compounds such as proteins were also tested for separation. The importance of this work is attributed to separation processes utilizing environmentally friendly conditions, since harsh chemical environments conventionally used to resolve biocompounds could cause their biological activities to be rendered inactive.
In this thesis entitled “Saccharide Recognition - Boronic acids as Receptors in Polymeric Networks” different aspects of boronic acid synthesis, their analysis and incorporation or attachment to different polymeric networks and characterisation thereof were investigated. The following key aspects were considered: • Provision of a variety of different characterised arylboronic acids and benzoboroxoles • Attachment of certain derivatives to nanoparticles and the characterisation of saccharide binding by means of isothermal titration calorimetry and displacement assay (ARS) to enhance the association constant to saccharides at pH 7.4 • Enhancement of selectivity in polymeric systems by means of molecular imprinting using fructose as template and a polymerisable benzoboroxole as functional monomer for the recognition at pH 7.4 (Joined by a diploma thesis of F. Grüneberger) • Development of biomimetic saccharide structures and the development of saccharide (especially glucose and fructose) binding MIPs by using these structures as template molecules. In the first part of the thesis different arylboronic acid derivatives were synthesised and their binding to glucose or fructose was investigated by means of isothermal titration calorimetry (ITC). It could be derived, which is in parallel to the literature, that derivatives bearing a methylhydroxyl-group in ortho-position to the boron (benzoboroxole) exhibit in most cases a two-fold higher association constant compared to the corresponding phenylboronic acid derivative. To gain a deeper understanding NMR spectroscopy and mass spectrometry with the benzoboroxole and glucose or fructose was performed. It could be shown that the exchange rate in terms of NMR time scale is quite slow since in titration experiments new peaks appeared. Via mass spectrometry of a mixture between benzoboroxole and glucose or fructose, different binding stoichiometries could be detected showing that the binding of saccharides is comparable with their binding to phenylboronic acid. In addition, the use of Alizarin Red S as an electrochemical reporter was described for the first time to monitor the saccharide binding to arylboronic acids not only with spectroscopy. Here, the redox behaviour and the displacement were recorded by cyclic voltammograms. In the second part different applications of boronic acids in polymeric networks were investigated. The attachment of benzoboroxoles to nanoparticles was investigated and monitored by means of isothermal titration calorimetry and a colourimetric assay with Alizarin Red S as the report dye. The investigations by isothermal titration calorimetry compared the fructose binding of arylboronic acids and benzoboroxoles coupled to these nanoparticles and “free” in solution. It could be shown that the attached derivatives showed a higher binding constant due to an increasing entropy term. This states for possible multivalent binding combined with a higher water release. Since ITC could not characterise the binding of glucose to these nanoparticles due to experimental restrictions the glucose binding at pH 7.4 was shown with ARS. Here, the displacement of ARS by fructose and also glucose could be followed and consequently these nanoparticles can be used for saccharide determination. Within this investigation also the temperature stability of these nanoparticles was examined and after normal sterilisation procedures (121°C, 20 min.) the binding behaviour was still unchanged. To target the selectivity of the used polymeric networks, molecular imprinting was used as a technique for creating artificial binding pockets on a molecular scale. As functional monomer 3-methacrylamidobenzoboroxole was introduced for the recognition of fructose. In comparison to polymers prepared with vinylphenylboronic acid the benzoboroxole containing polymer had a stronger binding at pH 7.4 which was shown for the first time. In addition, another imprinted polymer was synthesised especially for the recognition of glucose and fructose employing biomimetic saccharide analogues as template molecule. The advantage to use the saccharide analogues is the defined template-functional monomer complex during the polymerisation which is not the case, for example, for glucose-boronic acid interaction. The biomimetic character was proven through structural superimposition of crystal structures of the analogues with already described crystal structures of boronic acid esters of glucose and fructose. A molecularly imprinted polymer was synthesised with vinylphenylboronic acid as the functional monomer to show that both glucose and fructose are able to bind to the polymer which was predicted by the structural similarity of the analogues. The major scientific contributions of this thesis are • the determination of binding constants for some, not yet reported saccharide – boronic acid / benzoboroxole pairs, • the use of ARS as electrochemical reporter for saccharide detection, • the thermodynamic characterisation of a saccharide binding nanoparticle system containing benzoboroxole and functioning at pH 7.4, • the use of a polymerisable benzoboroxole as functional monomer for saccharide recognition in neutral, aqueous environments • and the synthesis and utilisation of biomimetic saccharide analogues as template molecules especially for the development of a glucose binding MIP.
In this thesis chemical reactions under hydrothermal conditions were explored, whereby emphasis was put on green chemistry. Water at high temperature and pressure acts as a benign solvent. Motivation to work under hydrothermal conditions was well-founded in the tunability of physicochemical properties with temperature, e.g. of dielectric constant, density or ion product, which often resulted in surprising reactivity. Another cornerstone was the implementation of the principles of green chemistry. Besides the use of water as solvent, this included the employment of a sustainable feedstock and the sensible use of resources by minimizing waste and harmful intermediates and additives. To evaluate the feasibility of hydrothermal conditions for chemical synthesis, exemplary reactions were performed. These were carried out in a continuous flow reactor, allowing for precise control of reaction conditions and kinetics measurements. In most experiments a temperature of 200 °C in combination with a pressure of 100 bar was chosen. In some cases the temperature was even raised to 300 °C. Water in this subcritical range can also be found in nature at hydrothermal vents on the ocean floor. On the primitive earth, environments with such conditions were however present in larger numbers. Therefore we tested whether biologically important carbohydrates could be formed at high temperature from the simple, probably prebiotic precursor formaldehyde. Indeed, this formose reaction could be carried out successfully, although the yield was lower compared to the counterpart reaction under ambient conditions. However, striking differences regarding selectivity and necessary catalysts were observed. At moderate temperatures bases and catalytically active cations like Ca2+ are necessary and the main products are hexoses and pentoses, which accumulate due to their higher stability. In contrast, in high-temperature water no catalyst was necessary but a slightly alkaline solution was sufficient. Hexoses were only formed in negligible amounts, whereas pentoses and the shorter carbohydrates accounted for the major fraction. Amongst the pentoses there was some preference for the formation of ribose. Even deoxy sugars could be detected in traces. The observation that catalysts can be avoided was successfully transferred to another reaction. In a green chemistry approach platform chemicals must be produced from sustainable resources. Carbohydrates can for instance be employed as a basis. They can be transformed to levulinic acid and formic acid, which can both react via a transfer hydrogenation to the green solvent and biofuel gamma-valerolactone. This second reaction usually requires catalysis by Ru or Pd, which are neither sustainable nor low-priced. Under hydrothermal conditions these heavy metals could be avoided and replaced by cheap salts, taking advantage of the temperature dependence of the acid dissociation constant. Simple sulfate was recognized as a temperature switchable base. With this additive high yield could be achieved by simultaneous prevention of waste. In contrast to conventional bases, which create salt upon neutralization, a temperature switchable base becomes neutral again when cooled down and thus can be reused. This adds another sustainable feature to the high atom economy of the presented hydrothermal synthesis. In a last study complex decomposition pathways of biomass were investigated. Gas chromatography in conjunction with mass spectroscopy has proven to be a powerful tool for the identification of unknowns. It was observed that several acids were formed when carbohydrates were treated with bases at high temperature. This procedure was also applied to digest wood. Afterwards it was possible to fermentate the solution and a good yield of methane was obtained. This has to be regarded in the light of the fact that wood practically cannot be used as a feedstock in a biogas factory. Thus the hydrothermal pretreatment is an efficient means to employ such materials as well. Also the reaction network of the hydrothermal decomposition of glycine was investigated using isotope-labeled compounds as comparison for the unambiguous identification of unknowns. This refined analysis allowed the identification of several new molecules and pathways, not yet described in literature. In summary several advantages could be taken from synthesis in high-temperature water. Many catalysts, absolutely necessary under ambient conditions, could either be completely avoided or replaced by cheap, sustainable alternatives. In this respect water is not only a green solvent, but helps to prevent waste and preserves resources.
The creation of complex polymer structures has been one of the major research topics over the last couple of decades. This work deals with the synthesis of (block co-)polymers, the creation of complex and stimuli-responsive aggregates by self-assembly, and the cross-linking of these structures. Also the higher-order self-assembly of the aggregates is investigated. The formation of poly-2-oxazoline based micelles in aqueous solution and their simultaneous functionalization and cross-linking using thiol-yne chemistry is e.g. presented. By introducing pH responsive thiols in the core of the micelles the influence of charged groups in the core of micelles on the entire structure can be studied. The charging of these groups leads to a swelling of the core and a decrease in the local concentration of the corona forming block (poly(2-ethyl-2-oxazoline)). This decrease in concentration yields a shift in the cloud point temperature to higher temperatures for this Type I thermoresponsive polymer. When the swelling of the core is prohibited, e.g. by the introduction of sufficient amounts of salt, this behavior disappears. Similar structures can be prepared using complex coacervate core micelles (C3Ms) built through the interaction of weakly acidic and basic polymer blocks. The advantage of these structures is that two different stabilizing blocks can be incorporated, which allows for more diverse and complex structures and behavior of the micelles. Using block copolymers with either a polyanionic or a polycationic block C3Ms could be created with a corona which contains two different soluble nonionic polymers, which either have a mixed corona or a Janus type corona, depending on the polymers that were chosen. Using NHS and EDC the micelles could easily be cross-linked by the formation of amide bonds in the core of the micelles. The higher-order self-assembly behavior of these core cross-linked complex coacervate core micelles (C5Ms) was studied. Due to the cross-linking the micelles are stabilized towards changes in pH and ionic strength, but polymer chains are also no longer able to rearrange. For C5Ms with a mixed corona likely network structures were formed upon the collapse of the thermoresponsive poly(N-isopropylacrylamide) (PNIPAAm), whereas for Janus type C5Ms well defined spherical aggregates of micelles could be obtained, depending on the pH of the solution. Furthermore it could be shown that Janus micelles can adsorb onto inorganic nanoparticles such as colloidal silica (through a selective interaction between PEO and the silica surface) or gold nanoparticles (by the binding of thiol end-groups). Asymmetric aggregates were also formed using the streptavidin-biotin binding motive. This is achieved by using three out of the four binding sites of streptavidin for the binding of one three-arm star polymer, end-functionalized with biotin groups. A homopolymer with one biotin end-group can be used to occupy the last position. This binding of two different polymers makes it possible to create asymmetric complexes. This phase separation is theoretically independent of the kind of polymer since the structure of the protein is the driving force, not the intrinsic phase separation between polymers. Besides Janus structures also specific cross-linking can be achieved by using other mixing ratios.
One of the main issues with the use of nickel titanium alloy (NiTi) implants in cardiovascular implants (stents) is that these devices must be of very high quality in order to avoid subsequent operations due to failing stents. For small stents with diameters below ca. 2 mm, however, stent characterization is not straightforward. One of the main problems is that there are virtually no methods to characterize the interior of the NiTi tubes used for fabrication of these tiny stents. The current paper reports on a robust hybrid actuator for the characterization of NiTi tubes prior to stent fabrication. The method is based on a polymer/hydrogel/magnetic nanoparticle hybrid material and allows for the determination of the inner diameter at virtually all places in the raw NiTi tubes. Knowledge of the inner structure of the raw NiTi tubes is crucial to avoid regions that are not hollow or regions that are likely to fail due to defects inside the raw tube. The actuator enables close contact of a magnetic polymer film with the inner NiTi tube surface. The magnetic signal can be detected from outside and be used for a direct mapping of the tube interior. As a result, it is possible to detect critical regions prior to expensive and slow stent fabrication processes.
With the rise of nanotechnology in the last decade, nanofluidics has been established as a research field and gained increased interest in science and industry. Natural aqueous nanofluidic systems are very complex, there is often a predominance of liquid interfaces or the fluid contains charged or differently shaped colloids. The effects, promoted by these additives, are far from being completely understood and interesting questions arise with regards to the confinement of such complex fluidic systems. A systematic study of nanofluidic processes requires designing suitable experimental model nano – channels with required characteristics. The present work employed thin liquid films (TLFs) as experimental models. They have proven to be useful experimental tools because of their simple geometry, reproducible preparation, and controllable liquid interfaces. The thickness of the channels can be adjusted easily by the concentration of electrolyte in the film forming solution. This way, channel dimensions from 5 – 100 nm are possible, a high flexibility for an experimental system. TLFs have liquid IFs of different charge and properties and they offer the possibility to confine differently shaped ions and molecules to very small spaces, or to subject them to controlled forces. This makes the foam films a unique “device” available to obtain information about fluidic systems in nanometer dimensions. The main goal of this thesis was to study nanofluidic processes using TLFs as models, or tools, and to subtract information about natural systems plus deepen the understanding on physical chemical conditions. The presented work showed that foam films can be used as experimental models to understand the behavior of liquids in nano – sized confinement. In the first part of the thesis, we studied the process of thinning of thin liquid films stabilized with the non – ionic surfactant n – dodecyl – β – maltoside (β – C₁₂G₂) with primary interest in interfacial diffusion processes during the thinning process dependent on surfactant concentration 64. The surfactant concentration in the film forming solutions was varied at constant electrolyte (NaCl) concentration. The velocity of thinning was analyzed combining previously developed theoretical approaches. Qualitative information about the mobility of the surfactant molecules at the film surfaces was obtained. We found that above a certain limiting surfactant concentration the film surfaces were completely immobile and they behaved as non – deformable, which decelerated the thinning process. This follows the predictions for Reynolds flow of liquid between two non – deformable disks. In the second part of the thesis, we designed a TLF nanofluidic system containing rod – like multivalent ions and compared this system to films containing monovalent ions. We presented first results which recognized for the first time the existence of an additional attractive force in the foam films based on the electrostatic interaction between rod – like ions and oppositely charged surfaces. We may speculate that this is an ion bridging component of the disjoining pressure. The results show that for films prepared in presence of spermidine the transformation of the thicker CF to the thinnest NBF is more probable as films prepared with NaCl at similar conditions of electrostatic interaction. This effect is not a result of specific adsorption of any of the ions at the fluid surfaces and it does not lead to any changes in the equilibrium properties of the CF and NBF. Our hypothesis was proven using the trivalent ion Y3+ which does not show ion bridging. The experimental results are compared to theoretical predictions and a quantitative agreement on the system’s energy gain for the change from CF to NBF could be obtained. In the third part of the work, the behavior of nanoparticles in confinement was investigated with respect to their impact on the fluid flow velocity. The particles altered the flow velocity by an unexpected high amount, so that the resulting changes in the dynamic viscosity could not be explained by a realistic change of the fluid viscosity. Only aggregation, flocculation and plug formation can explain the experimental results. The particle systems in the presented thesis had a great impact on the film interfaces due to the stabilizer molecules present in the bulk solution. Finally, the location of the particles with respect to their lateral and vertical arrangement in the film was studied with advanced reflectivity and scattering methods. Neutron Reflectometry studies were performed to investigate the location of nanoparticles in the TLF perpendicular to the IF. For the first time, we study TLFs using grazing incidence small angle X – ray scattering (GISAXS), which is a technique sensitive to the lateral arrangement of particles in confined volumes. This work provides preliminary data on a lateral ordering of particles in the film.
Nanofibrous mats are interesting scaffold materials for biomedical applications like tissue engineering due to their interconnectivity and their size dimension which mimics the native cell environment. Electrospinning provides a simple route to access such fiber meshes. This thesis addresses the structural and functional control of electrospun fiber mats. In the first section, it is shown that fiber meshes with bimodal size distribution could be obtained in a single-step process by electrospinning. A standard single syringe set-up was used to spin concentrated poly(ε-caprolactone) (PCL) and poly(lactic-co-glycolic acid) (PLGA) solutions in chloroform and meshes with bimodal-sized fiber distribution could be directly obtained by reducing the spinning rate at elevated humidity. Scanning electron microscopy (SEM) and mercury porosity of the meshes suggested a suitable pore size distribution for effective cell infiltration. The bimodal fiber meshes together with unimodal fiber meshes were evaluated for cellular infiltration. While the micrometer fibers in the mixed meshes generate an open pore structure, the submicrometer fibers support cell adhesion and facilitate cell bridging on the large pores. This was revealed by initial cell penetration studies, showing superior ingrowth of epithelial cells into the bimodal meshes compared to a mesh composed of unimodal 1.5 μm fibers. The bimodal fiber meshes together with electrospun nano- and microfiber meshes were further used for the inorganic/organic hybrid fabrication of PCL with calcium carbonate or calcium phosphate, two biorelevant minerals. Such composite structures are attractive for the potential improvement of properties such as stiffness or bioactivity. It was possible to encapsulate nano and mixed sized plasma-treated PCL meshes to areas > 1 mm2 with calcium carbonate using three different mineralization methods including the use of poly(acrylic acid). The additive seemed to be useful in stabilizing amorphous calcium carbonate to effectively fill the space between the electrospun fibers resulting in composite structures. Micro-, nano- and mixed sized fiber meshes were successfully coated within hours by fiber directed crystallization of calcium phosphate using a ten-times concentrated simulated body fluid. It was shown that nanofibers accelerated the calcium phosphate crystallization, as compared to microfibers. In addition, crystallizations performed at static conditions led to hydroxyapatite formations whereas in dynamic conditions brushite coexisted. In the second section, nanofiber functionalization strategies are investigated. First, a one-step process was introduced where a peptide-polymer-conjugate (PLLA-b-CGGRGDS) was co-spun with PLGA in such a way that the peptide is enriched on the surface. It was shown that by adding methanol to the chloroform/blend solution, a dramatic increase of the peptide concentration at the fiber surface could be achieved as determined by X-ray photoelectron spectroscopy (XPS). Peptide accessibility was demonstrated via a contact angle comparison of pure PLGA and RGD-functionalized fiber meshes. In addition, the electrostatic attraction between a RGD-functionalized fiber and a silica bead at pH ~ 4 confirmed the accessibility of the peptide. The bioactivity of these RGD-functionalized fiber meshes was demonstrated using blends containing 18 wt% bioconjugate. These meshes promoted adhesion behavior of fibroblast compared to pure PLGA meshes. In a second functionalization approach, a modular strategy was investigated. In a single step, reactive fiber meshes were fabricated and then functionalized with bioactive molecules. While the electrospinning of the pure reactive polymer poly(pentafluorophenyl methacrylate) (PPFPMA) was feasible, the inherent brittleness of PPFPMA required to spin a PCL blend. Blends and pure PPFPMA showed a two-step functionalization kinetics. An initial fast reaction of the pentafluorophenyl esters with aminoethanol as a model substance was followed by a slow conversion upon further hydrophilization. This was analysed by UV/Vis-spectroscopy of the pentaflurorophenol release upon nucleophilic substitution with the amines. The conversion was confirmed by increased hydrophilicity of the resulting meshes. The PCL/PPFPMA fiber meshes were then used for functionalization with more complex molecules such as saccharides. Aminofunctionalized D-Mannose or D-Galactose was reacted with the active pentafluorophenyl esters as followed by UV/Vis spectroscopy and XPS. The functionality was shown to be bioactive using macrophage cell culture. The meshes functionalized with D-Mannose specifically stimulated the cytokine production of macrophages when lipopolysaccharides were added. This was in contrast to D-Galactose- or aminoethanol-functionalized and unfunctionalized PCL/PPFPMA fiber mats.