Refine
Has Fulltext
- yes (2) (remove)
Document Type
- Doctoral Thesis (2) (remove)
Language
- German (2) (remove)
Keywords
- Stärke (2) (remove)
Institute
In den letzten Jahrzehnten fand auch in der Beschichtungsindustrie ein Umdenken hin zu umweltfreundlicheren Farben und Lacken statt. Allerdings basieren auch neue Lösungen meist nicht auf Biopolymeren und in einem noch geringeren Anteil auf wasserbasierten Beschichtungssystemen aus nachwachsenden Rohstoffen. Dies stellt den Anknüpfungspunkt dieser Arbeit dar, in der untersucht wurde, ob das Biopolymer Stärke das Potenzial zum wasserbasierten Filmbildner für Farben und Lacke besitzt. Dabei müssen angelehnt an etablierte synthetische Marktprodukte die folgenden Kriterien erfüllt werden: Die wässrige Dispersion muss mindestens einen 30%igen Feststoffgehalt haben, bei Raumtemperatur verarbeitet werden können und Viskositäten zwischen 10^2-10^3 mPa·s aufweisen. Die finale Beschichtung muss einen geschlossenen Film bilden und sehr gute Haftfestigkeiten zu einer spezifischen Oberfläche, in dieser Arbeit Glas, besitzen. Als Grundlage für die Modifizierung der Stärke wurde eine Kombination von molekularem Abbau und chemischer Funktionalisierung ausgewählt. Da nicht bekannt war, welchen Einfluss die Stärkeart, die gewählte Abbaureaktion als auch verschiedene Substituenten auf die Dispersionsherstellung und deren Eigenschaften sowie die Beschichtungseigenschaften ausüben könnten, wurden die strukturellen Parameter getrennt voneinander untersucht.
Das erste Themengebiet beinhaltete den oxidativen Abbau von Kartoffel- und Palerbsenstärke mittels des Hypochlorit-Abbaus (OCl-) und des ManOx-Abbaus (H2O2, KMnO4). Mit beiden Abbaureaktionen konnten vergleichbare gewichtsmittlere Molmassen (Mw) von 2·10^5-10^6 g/mol (GPC-MALS) hergestellt werden. Allerdings führten die gewählten Reaktionsbedingungen beim ManOx-Abbau zur Bildung von Gelpartikeln. Diese lagen im µm-Bereich (DLS und Kryo-REM-Messungen) und hatten zur Folge, dass die ManOx-Proben deutlich erhöhte Viskositäten (c: 7,5 %; 9-260 mPa·s) im Vergleich zu den OCl--Proben (4-10 mPa·s) bei scherverdünnendem Verhalten besaßen und die Eigenschaften von viskoelastischen Gelen (G‘ > G‘‘) zeigten. Des Weiteren wiesen sie reduzierte Heißwasserlöslichkeiten (95 °C, vorrangig: 70-99 %) auf. Der OCl--Abbau führte zu hydrophileren (Carboxylgruppengehalt bis zu 6,1 %; ManOx: bis zu 3,1 %), nach 95 °C-Behandlung vollständig wasserlöslichen abgebauten Stärken, die ein Newtonsches Fließverhalten mit Eigenschaften einer viskoelastischen Flüssigkeit (G‘‘ > G‘) hatten. Die OCl--Proben konnten im Vergleich zu den ManOx-Produkten (10-20 %) zu konzentrierteren Dispersionen (20-40 %) verarbeitet werden, die gleichzeitig die Einschränkung von anwendungsrelevanten Mw auf < 7·10^5 g/mol zuließen (Konzentration sollte > 30 % sein). Außerdem führten nur die OCl--Proben der Kartoffelstärke zu transparenten (alle anderen waren opak) geschlossenen Beschichtungsfilmen. Somit hebt sich die Kombination von OCl--Abbau und Kartoffelstärke mit Hinblick auf die Endanwendung ab.
Das zweite Themengebiet umfasste Untersuchungen zum Einfluss von Ester- und Hydroxyalkylether-Substituenten auf Basis einer industriell abgebauten Kartoffelstärke (Mw: 1,2·10^5 g/mol) vor allem auf die Dispersionsherstellung, die rheologischen Eigenschaften der Dispersionen und die Beschichtungseigenschaften in Kombination mit Glassubstraten. Dazu wurden Ester und Ether mit DS/MS-Werten von 0,07-0,91 synthetisiert. Die Derivate konnten zu wasserbasierten Dispersionen mit Konzentrationen von 30-45 % verarbeitet werden, wobei bei hydrophoberen Modifikaten ein Co-Lösemittel, Diethylenglycolmonobutylether (DEGBE), eingesetzt werden musste. Die Feststoffgehalte sanken dabei für beide Derivatklassen vor allem mit zunehmender Alkylkettenlänge. Die anwendungsrelevanten Viskositäten (323-1240 mPa·s) stiegen auf Grund von Wechselwirkungen tendenziell mit DS/MS und Alkylkettenlänge an. Hinsichtlich der Beschichtungseigenschaften erwiesen sich die Ester vergleichend zu den Ethern als die bevorzugte Substituentenklasse, da nur die Ester geschlossene, defektfreie und mehrheitlich transparente Beschichtungsfilme bildeten, die exzellente bis sehr gute Haftfestigkeiten (ISO Klasse: 0 und 1) auf Glas besaßen. Die Ether bildeten mehrheitlich brüchige Filme. Basierend auf der Kombination der Ergebnisse aus Lösemittelaustausch, den rheologischen Untersuchungen und zusätzlichen Oberflächenspannungsmessungen (30-61 mN/m) konnte geschlossen werden, dass wahrscheinlich fehlende oder schlechte Haftfestigkeiten vorrangig akkumuliertem Wasser in den Beschichtungsfilmen (visuell: trüb oder weiß) geschuldet sind, während die Brüchigkeit vermutlich auf Wechselwirkungen (H-Brücken Wechselwirkungen, hydrophobe Wechselwirkungen) zwischen den Polymeren zurückgeführt werden kann.
Insgesamt scheint die Kombination aus Kartoffelstärke basierend auf dem OCl--Abbau mit Mw < 7·10^5 g/mol und einem Estersubstituenten eine gute Wahl für wasserbasierte Dispersionen mit hohen Feststoffkonzentrationen (> 30 %), guter Filmbildung und exzellenten Haftungen auf Glas zu sein.
In den vergangenen Jahren wurden stetig wachsende Produktionskapazitäten von Biokunststoffen aus nachwachsenden Rohstoffe nverzeichnet. Trotz großer Produktionskapazitäten und einem geeigneten Eigenschaftsprofil findet Stärke nur als hydrophile, mit Weichmachern verarbeitete thermoplastische Stärke (TPS) in Form von Blends mit z. B. Polyestern Anwendung. Gleiches gilt für Kunststoffe auf Proteinbasis. Die vorliegende Arbeit hat die Entwicklung von Biokunststoffen auf Stärkebasis zum Ziel, welche ohne externe Weichmacher thermoplastisch verarbeitbar und hydrophob sind sowie ein mechanisches Eigenschaftsprofil aufweisen, welches ein Potenzial zur Herstellung von Materialien für eine Anwendung als Verpackungsmittel bietet. Um die Rohstoffbasis für Biokunststoffe zu erweitern, soll das erarbeitete Konzept auf zwei industriell verfügbare Proteintypen, Zein und Molkenproteinisolat (WPI), übertragen werden. Als geeignete Materialklasse wurden Fettsäureester der Stärke herausgearbeitet. Zunächst fand ein Vergleich der Säurechlorid-Veresterung und der Umesterung von Fettsäurevinylestern statt, woraus letztere als geeignetere Methode hervorging. Durch Variation der Reaktionsparameter konnte diese optimiert und auf eine Serie der Fettsäurevinylester von Butanoat bis Stearat für DS-Werte bis zu 2,2-2,6 angewandt werden. Möglich war somit eine systematische Studie unter Variation der veresterten Fettsäure sowie des Substitutionsgrades (DS). Sämtliche Produkte mit einem DS ab 1,5 wiesen eine ausgprägte Löslichkeit in organischen Lösungsmitteln auf wodurch sowohl die Aufnahme von NMR-Spektren als auch Molmassenbestimmung mittels Größenausschlusschromatographie mit gekoppelter Mehrwinkel-Laserlichtstreuung (GPC-MALLS) möglich waren. Durch dynamische Lichtstreuung (DLS) wurde das Löslichkeitsverhalten veranschaulicht. Sämtliche Produkte konnten zu Filmen verarbeitet werden, wobei Materialien mit DS 1,5-1,7 hohe Zugfestigkeiten (bis zu 42 MPa) und Elastizitätsmodule (bis 1390 MPa) aufwiesen. Insbesondere Stärkehexanoat mit DS <2 sowie Stärkebutanoat mit DS >2 hatten ein mechanisches Eigenschaftsprofil, welches insbesondere in Bezug auf die Festigkeit/Steifigkeit vergleichbar mit Verpackungsmaterialien wie Polyethylen war (Zugfestigkeit: 15-32 MPa, E-Modul: 300-1300 MPa). Zugfestigkeit und Elastizitätsmodul nahmen mit steigender Kettenlänge der veresterten Fettsäure ab. Ester längerkettiger Fettsäuren (C16-C18) waren spröde. Über Weitwinkel-Röntgenstreuung (WAXS) und Infrarotspektroskopie (ATR-FTIR) konnte der Verlauf der Festigkeiten mit einer zunehmenden Distanz der Stärke im Material begründet werden. Es konnten von DS und Kettenlänge abhängige Glasübergänge detektiert werden, die kristallinen Strukturen der langkettigen Fettsäuren zeigten einen Schmelzpeak. Die Hydrophobie der Filme wurde anhand von Kontaktwinkeln >95° gegen Wasser dargestellt. Blends mit biobasierten Polyterpenen sowie den in der Arbeit hergestellten Zein-Acylderivaten ermöglichten eine weitere Verbesserung der Zugfestigkeit bzw. des Elastizitätsmoduls hochsubstituierter Produkte. Eine thermoplastische Verarbeitung mittels Spritzgießen war sowohl für Produkte mit hohem als auch mittlerem DS-Wert ohne jeglichen Zusatz von Weichmachern möglich. Es entstanden homogene, transparente Prüfstäbe. Untersuchungen der Härte ergaben auch hier für Stärkehexanoat und –butanoat mit Polyethylen vergleichbare Werte. Ausgewählte Produkte wurden zu Fasern nach dem Schmelzspinnverfahren verarbeitet. Hierbei wurden insbesondere für hochsubstituierte Derivate homogenen Fasern erstellt, welche im Vergleich zur Gießfolie signifikant höhere Zugfestigkeiten aufwiesen. Stärkeester mit mittlerem DS ließen sich ebenfalls verarbeiten. Zunächst wurden für eine Übertragung des Konzeptes auf die Proteine Zein und WPI verschiedene Synthesemethoden verglichen. Die Veresterung mit Säurechloriden ergab hierbei die höchsten Werte. Im Hinblick auf eine gute Löslichkeit in organischen Lösungsmitteln wurde für WPI die Veresterung mit carbonyldiimidazol (CDI)-aktivierten Fettsäuren in DMSO und für Zein die Veresterung mit Säu-rechloriden in Pyridin bevorzugt. Es stellte sich heraus, dass acyliertes WPI zwar hydrophob, jedoch ohne Weichmacher nicht thermoplastisch verarbeitet werden konnte. Die Erstellung von Gießfolien führte zu Sprödbruchverhalten. Unter Zugabe der biobasierten Ölsäure wurde die Anwendung von acyliertem WPI als thermoplastischer Filler z. B. in Blends mit Stärkeestern dargestellt. Im Gegensatz hierzu zeigte acyliertes Zein Glasübergänge <100 °C bei ausreichender Stabilität (150-200 °C). Zeinoleat konnte ohne Weichmacher zu einer transparenten Gießfolie verarbeitet werden. Sämtliche Derivate erwiesen sich als ausgeprägt hydrophob. Zeinoleat konnte über das Schmelzspinnverfahren zu thermoplastischen Fasern verarbeitet werden.