Refine
Year of publication
Document Type
- Article (47) (remove)
Language
- English (47) (remove)
Keywords
- morphology (47) (remove)
Institute
- Department Linguistik (30)
- Institut für Physik und Astronomie (6)
- Institut für Chemie (4)
- Institut für Biochemie und Biologie (3)
- Department Psychologie (1)
- Humanwissenschaftliche Fakultät (1)
- Institut für Germanistik (1)
- Institut für Mathematik (1)
- Multilingualism (1)
- Potsdam Research Institute for Multilingualism (PRIM) (1)
Cryo-electron microscopy, atomic force microscopy, and light microscopy investigations provide experimental evidence that amphiphilic emulsion copolymerization particles change their morphology in dependence on concentration. The shape of the particles is spherical at solids content above 1%, but it changes to rod-like, ring-like, and web-like structures at lower concentrations. In addition, the shape and morphology of these particles at low concentrations are not fixed but very flexible and vary with time between spheres, flexible pearlnecklace structures, and stretched rods.
A form-function mismatch?
(2019)
Accusative Unaccusatives
(2019)
Bienenfresserortungsversuch
(2019)
A series of multiblock copolymers (PDLCL) synthesized from oligo(omega-pentadecalactone) diol (OPDL) and oligo(epsilon-caprolactone) diol (OCL), which are linked by 2,2(4), 4-trimethyl-hexamethylene diisocyanate (TMDI), is investigated by the Langmuir monolayer technique at the air-water interface. Brewster angle microscopy (BAM) and spectroscopic ellipsometry are employed to characterize the polymer film morphologies in situ. PDLCL containing >= 40 wt% OCL segments form homogeneous Langmuir monofilms after spreading. The film elasticity modulus decreases with increasing amounts of OPDL segments in the copolymer. In contrast, the OCL-free polyesterurethane OPDL-TMDI cannot be spread to monomolecular films on the water surface properly, and movable slabs are observed by BAM even at low surface pressures. The results of the in situ morphological characterization clearly show that essential information concerning the reliability of Langmuir monolayer degradation (LMD) experiments cannot be obtained from the evaluation of the pi-A isotherms only. Consequently, in situ morphological characterization turns out to be indispensable for characterization of Langmuir layers before LMD experiments.
Organic bulk heterojunction (BHJ) solar cells require energetic offsets between the donor and acceptor to obtain high short-circuit currents (J(SC)) and fill factors (FF). However, it is necessary to reduce the energetic offsets to achieve high open-circuit voltages (V-OC). Recently, reports have highlighted BHJ blends that are pushing at the accepted limits of energetic offsets necessary for high efficiency. Unfortunately, most of these BHJs have modest FF values. How the energetic offset impacts the solar cell characteristics thus remains poorly understood. Here, a comprehensive characterization of the losses in a polymer:fullerene BHJ blend, PIPCP:phenyl-C61-butyric acid methyl ester (PC61BM), that achieves a high V-OC (0.9 V) with very low energy losses (E-loss = 0.52 eV) from the energy of absorbed photons, a respectable J(SC) (13 mA cm(-2)), but a limited FF (54%) is reported. Despite the low energetic offset, the system does not suffer from field-dependent generation and instead it is characterized by very fast nongeminate recombination and the presence of shallow traps. The charge-carrier losses are attributed to suboptimal morphology due to high miscibility between PIPCP and PC61BM. These results hold promise that given the appropriate morphology, the J(SC), V-OC, and FF can all be improved, even with very low energetic offsets.