Refine
Has Fulltext
- no (22)
Document Type
- Article (19)
- Conference Proceeding (2)
- Monograph/Edited Volume (1)
Is part of the Bibliography
- yes (22)
Keywords
- radical polymerization (3)
- copolymerization (2)
- ) (1)
- EPR (1)
- ESR (1)
- atom transfer radical polymerization (ATRP) (1)
- block copolymers (1)
- fluorinated olefins (1)
- fluoropolymers (1)
- hexafluoropropene (1)
- ionic liquid (1)
- kinetics (polym (1)
- kinetics (polym) (1)
- kinetics (polym.) (1)
- methacrylates (1)
- phase behavior (1)
- pulse laser initiated polymerization (1)
- solvent influence (1)
- supercritical CO(2) (1)
- supercritical carbon dioxide (1)
- termination (1)
- vinylidene fluoride (1)
Institute
- Institut für Chemie (22)
The SP-PLP-EPR technique is used to carry out a detailed investigation of the radical termination kinetics of 1H, 1H, 2H, 2H-tridecafluorooctyl methacrylate (TDFOMA) in bulk at relatively low conversion. Composite-model behavior for chain-length-dependent termination rate coefficients, kti,i, is observed. It is found that for TDFOMA, ic approximate to 60 independent of temperature, and as approximate to 0.65 and al approximate to 0.2 at 80 degrees C and above. However, at lower temperatures the situation is strikingly different, with the significantly higher average values of as = 0.89 +/- 0.15 and al = 0.32 +/- 0.10 being obtained at 50 degrees C and below. This makes TDFOMA the first monomer to be found that exhibits clearly different exponent values, as and al, at lower and higher temperature, and that has both a high as, like an acrylate, and a high ic, like a methacrylate.
The surface of single-walled carbon nanotubes (SWCNTs) was functionalized with azide-terminated poly(vinylidene fluoride) (PVDF). Functionalization was confirmed by dispersibility, Raman spectroscopy, and thermogravimetric analyses. Raman spectra show disordering of the SWCNTs, thus, strongly suggesting that PVDF was covalently attached to SWCNTs. Functionalized SWCNTs were mixed with commercially available PVDF in a twin-screw extruder and thin films were obtained by melt-pressing. Films containing 0.5 and 1 wt% PVDF-functionalized SWCNTs exhibited significantly improved electrical conductivity compared to PVDF films containing pristine SWCNTs.
In ihrer Vorlesung zeigt Sabine Beuermann, unter welchen Bedingungen Kohlendioxid als Reaktionsmedium für die Herstellung von polymeren Materialien genutzt werden kann. Fluides Kohlendioxid ist ein attraktives Reaktionsmedium, da es ungiftig und nicht brennbar ist. Zudem leistet es einen wichtigen Beitrag zur Entwicklung nachhaltiger chemischer Prozesse, da durch den Einsatz von Kohlendioxid die Verwendung von organischen Lösungsmitteln vermieden werden kann.
Propagation rate coefficients for homogeneous phase VDF-HFP copolymerization in supercritical CO2
(2012)
For the first time, propagation rate coefficients, kp,COPO, for the copolymerizations of vinylidene fluoride and hexafluoropropene have been determined. The kinetic data was determined via pulsed-laser polymerization in conjunction with polymer analysis via size-exclusion chromatography, the PLP-SEC technique. The experiments were carried out in homogeneous phase with supercritical CO2 as solvent for temperatures ranging from 45 to 90 degrees C. Absolute polymer molecular weights were calculated on the basis of experimentally determined MarkHouwink constants. The Arrhenius parameters of kp,COPO vary significantly compared with ethene, which is explained by the high electronegativity of fluorine and less intra- and intermolecular interactions between the partially fluorinated macroradicals.
The influence of the reaction medium (organic solvents, water, ionic liquids, supercritical CO2) on the propagation rate in radical polymerizations has very different causes, e.g., hindered rotational modes, hydrogen bonding or electron pair donor/acceptor interactions. Depending on the origin of the solvent influence propagation rate coefficients, k(P), may be enhanced by up to an order of magnitude associated with changes in the pre-exponential or the activation energy of k(P). In contrast, non-specific interactions, size and steric effects lead to rather small changes in the vicinity of the radical chain end and are reflected by modest variations in k(P).
The influence of the reaction medium (organic solvents, water, ionic liquids, supercritical CO2) on the propagation rate in radical polymerizations has very different causes, e.g., hindered rotational modes, hydrogen bonding, or electron pair donor / acceptor interactions. Depending on the origin of the solvent influence propagation rate coefficients, kp, may be enhanced by up to an order of magnitude associated with changes in the pre-exponential or the activation energy of kp. Contrary, non-specific interactions, size and steric effects lead to rather small changes in the vicinity of the radical chain end and are reflected by modest variations in kp.
Mesoporous silica monoliths were prepared by the sol - gel technique and. lled with 1-ethyl-3-methyl imidazolium [Emim]-X (X = dicyanamide [N(CN)(2)], ethyl sulfate [EtSO4], thiocyanate [SCN], and triflate [TfO]) ionic liquids (ILs) using a methanol-IL exchange technique. The structure and behavior of the ILs inside the silica monoliths were studied using X-ray scattering, nitrogen sorption, IR spectroscopy, solid-state NMR, and thermal analysis. DSC finds shifts in both the glass transition temperature and melting points (where applicable) of the ILs. Glass transition and melting occur well below room temperature. There is thus no conflict with the NMR and IR data, which show that the ILs are as mobile at room temperature as the bulk (not confined) ILs. The very narrow line widths of the NMR spectra suggest that the ILs in our materials have the highest mobility reported for confined ILs so far. As a result, our data suggest that it is possible to generate IL/silica hybrid materials (ionogels) with bulk-like properties of the IL. This could be interesting for applications in, e.g., the solar cell or membrane fields.
Polyglycolide (PGA) is a biodegradable polymer with multiple applications in the medical sector. Here the synthesis of high molecular weight polyglycolide by ring-opening polymerization of diglycolide is reported. For the first time stabilizer free supercritical carbon dioxide (scCO(2)) was used as a reaction medium. scCO(2) allowed for a reduction in reaction temperature compared to conventional processes. Together with the lowering of monomer concentration and consequently reduced heat generation compared to bulk reactions thermal decomposition of the product occurring already during polymerization is strongly reduced. The reaction temperatures and pressures were varied between 120 and 150 degrees C and 145 to 1400 bar. Tin(II) ethyl hexanoate and 1-dodecanol were used as catalyst and initiator, respectively. The highest number average molecular weight of 31 200 g mol(-1) was obtained in 5 hours from polymerization at 120 degrees C and 530 bar. In all cases the products were obtained as a dry white powder. Remarkably, independent of molecular weight the melting temperatures were always at (219 +/- 2)degrees C.