Refine
Year of publication
Document Type
- Article (22)
- Postprint (3)
- Conference Proceeding (1)
Language
- English (26)
Is part of the Bibliography
- yes (26)
Keywords
- Azobenzene containing cationic surfactants (2)
- Photosensitive polymer brushes (2)
- atomic force microscopy (AFM) (2)
- diselenide (2)
- grafted polymers (2)
- molecular bottle brushes (2)
- sequence-controlled polymers (2)
- single chain folding (2)
- Dictyostelium discoideum (1)
- Opto-mechanically induced scission of (1)
Institute
We report on a process inducing photomechanical fracture of chemical bonds in photosensitive PMAA polymer brushes. The photosensitive PMAA polymer brushes were prepared by covalent attachment of azobenzene groups to poly(methylacrylic acid) (PMAA) chains generated by surface-initiated polymerization. While homogeneous irradiation leaves the polymer topography unchanged, the azo-PMAA brushes show a strong response upon irradiation with UV interference patterns. The photoisomerization process in the surface-attached polymer films results in the irreversible formation of surface relief gratings (SRG), which are strongly enhanced upon washing with a good solvent for the polymer. The photomechanical forces during mass transport induced by the irradiation lead to the scission of covalent bounds and accordingly to a degrafting of the polymer chains in areas where the polymer is receding from. It is observed that the number of ruptured chains depends strongly on the amount of azo side chains in the polymer.
Nanogradient polymer brushes
(2012)
In this paper, we report on the properties of nano-slits created in metal thin films using atomic force microscope (AFM) nanolithography (AFM-NL). We demonstrate that instead of expensive diamond AFM tips, it is also possible to use low cost silicon nitride tips. It is shown that depending on the direction of scratching, nano-slits of different widths and depths can be fabricated at constant load force. We elucidate the reasons for this behavior and identify an optimal direction and load force for scratching a gold layer.
The interface between thin films of metal and polymer materials play a significant role in modern flexible microelectronics viz., metal contacts on polymer substrates, printed electronics and prosthetic devices. The major emphasis in metal polymer interface is on studying how the externally applied stress in the polymer substrate leads to the deformation and cracks in metal film and vice versa. Usually, the deformation process involves strains varying over large lateral dimensions because of excessive stress at local imperfections. Here we show that the seemingly random phenomena at macroscopic scales can be rendered rather controllable at submicrometer length scales. Recently, we have created a metal polymer interface system with strains varying over periods of several hundred nanometers. This was achieved by exploiting the formation of surface relief grating (SRG) within the azobenzene containing photosensitive polymer film upon irradiation with light interference pattern. Up to a thickness of 60 nm, the adsorbed metal film adapts neatly to the forming relief, until it ultimately ruptures into an array of stripes by formation of highly regular and uniform cracks along the maxima and minima of the polymer topography. This surprising phenomenon has far-reaching implications. This is the first time a direct probe is available to estimate the forces emerging in SRG formation in glassy polymers. Furthermore, crack formation in thin metal films can be studied literally in slow motion, which could lead to substantial improvements in the design process of flexible electronics. Finally, cracks are produced uniformly and at high density, contrary to common sense. This could offer new strategies for precise nanofabrication procedures mechanical in character.
In this paper we report on an opto-mechanical scission of polymer chains within photosensitive diblock-copolymer brushes grafted to flat solid substrates. We employ surface-initiated polymerization of methylmethacrylate (MMA) and t-butyl methacrylate (tBMA) to grow diblock-copolymer brushes of poly(methylmethacrylate-b-t-butyl methacrylate) following the atom transfer polymerization (ATRP) scheme. After the synthesis, deprotection of the PtBMA block yields poly(methacrylic acid) (PMAA). To render PMMA-b-PMAA copolymers photosensitive, cationic azobenzene containing surfactants are attached to the negatively charged outer PMAA block. During irradiation with an ultraviolet (UV) interference pattern, the extent of photoisomerization of the azobenzene groups varies spatially and results in a topography change of the brush, i.e., formation of surface relief gratings (SRG). The SRG formation is accompanied by local rupturing of the polymer chains in areas from which the polymer material recedes. This opto-mechanically induced scission of the polymer chains takes place at the interfaces of the two blocks and depends strongly on the UV irradiation intensity. Our results indicate that this process may be explained by employing classical continuum fracture mechanics, which might be important for tailoring the phenomenon for applying it to poststructuring of polymer brushes.
We report on rendering polyelectrolyte brushes photosensitive by loading them with azobenzene-containing cationic surfactants. Planar poly(methacrylic acid) (PMAA) brushes are synthesized using the “grafting from” free-radical polymerization scheme followed by exposure to a solution of photosensitive surfactants consisting of positively-charged head groups and hydrophobic tails into which azobenzene moieties are inserted. In this study the length of the hydrophobic methylene spacer connecting the azobenzene and the charged head group ranges from 4 to 10 CH2 groups. Under irradiation with UV light, the photo-isomerization of azobenzene integrated into a surfactant results in a change in size, geometry, dipole moment and free volume of the whole molecule. When the brush loaded with photosensitive surfactants is exposed to irradiation with UV interference patterns, the topography of the brush deforms following the distribution of the light intensity, exhibiting surface relief gratings (SRG). Since SRG formation is accompanied by a local rupturing of polymer chains in areas from which the polymer material is receding, most of the polymer material is removed from the surface during treatment with good solvent, leaving behind characteristic patterns of lines or dots. The azobenzene molecules still integrated within the polymer film can be removed by washing the brush with water. The remaining nano-structured brush can then be re-used for further functionalization. Although the opto-mechanically induced rupturing occurs for all surfactants, larger species do not penetrate deep enough into the brush such that after rupturing a leftover layer of polymer material remains on the substrate. This indicates that rupturing occurs predominantly in regions of high surfactant density.