Refine
Year of publication
Document Type
- Article (18)
- Doctoral Thesis (1)
- Postprint (1)
Is part of the Bibliography
- yes (20)
Keywords
Institute
A confocal set-up is presented that improves micro-XRF and XAFS experiment with high-pressure e diamond-anvil cells (DACs) In this experiment a probing volume is defined by the focus of the incoming synchrotron radiation beam and that of a polycapillary X-ray half-lens with a very long working distance, which is placed in front of the fluorescence detector This set-up enhances the quality of the fluorescence and XAFS spectra, and thus the sensitivity for detecting elements at low concentrations. It efficiently suppresses signal from outside the sample chamber, which stems from elastic and inelastic scattering of the incoming beam by the diamond anvils as well as from excitation of fluorescence from the body of the DAC
The iron speciation in hydrous haplotonalitic and haplogranitic silicate glasses was studied using XAFS spectroscopy and transmission electron microscopy (TEM). Spectral features occurring at the main crest of the XANES at the iron K-edge of hydrous glasses indicate contributions to the spectra by iron-moieties present in a more ordered structural environment than found in the dry glass. These differences are also suggested by analysis of the EXAFS. These effects are not completely suppressed even for those samples that were quenched with a higher cooling rate. Strongest differences to the dry glass are observed for a sample that was quenched slowly through the temperature of glass transformation. Crystals (60 to 1500 nm in size) of magnetite, maghemite and another unidentified phase were observed in this sample by TEM, whereas no crystals were found in samples quenched with regular or high cooling rates. In-situ XANES measurements up to 700 degrees C and 500 MPa were performed to reveal the origin (i.e., during synthesis or quench) of the structural differences for those hydrous glasses that do not display any detectable crystallization. The comparison of XANES spectra collected on Fe2+ in water-saturated haplogranitic melt at 700 degrees C and 500 MPa and on Fe2+ in dry melt at 1150 degrees C shows that the local structural environment of Fe2+ in both systems is similar. This indicates that there is no detectable and direct influence of water on the local structure around iron in this type of melt. Hence, the differences observed between hydrous and dry glasses can only be related to artefacts formed during the quench process. (c) 2006 Elsevier B.V. All rights reserved
The crystallization kinetics of silicate liquids were studied experimentally in the system haplogranite-B-Li-H2O, at variable degrees of undercooling and variable water concentration. We investigated the kinetics of nucleation and crystallization of unseeded synthetic hydrous haplogranite with 1 wt % Li2O + 2 center dot 3 wt % B2O3 added (composition C1) and 2 wt % Li2O + 4 center dot 6 wt % B2O3 added (composition C2). Compositions C1 and C2 are simplified representative bulk compositions of Li-rich pegmatites and their highly differentiated cores, respectively. Starting water contents varied between 3 and 9 wt %. With few exceptions, the system remained water-undersaturated. About 86 isothermal runs of 1-60 days duration, grouped in 25 time series of constant temperature and initial H2O content, were carried out at temperatures from 400 to 700A degrees C at 300 MPa, corresponding to variable degrees of undercooling between the liquidus and glass transition. Viscosity measurements indicate that the glass transition for both compositions is below 400A degrees C for 3 wt % water and below 300A degrees C for 6 center dot 5 wt % water. The melts remained virtually crystal free at 400A degrees C, about 100A degrees C and 120A degrees C above the glass transition for compositions C1 and C2, respectively, in experiments up to 30 days long. This result is consistent with the existence of low-temperature, undercooled melts in the crust. At lower values of undercooling the runs crystallized partially, up to about 70% volume fraction. Undercooling and the amount of water are the main factors controlling nucleation and growth rates, and therefore textures. Minerals nucleate and grow sequentially according to mineral-specific nucleation delays. The mineral assemblage started with Li-Al stuffed quartz (in C1) and virgilite (in C2), solid-solutions between quartz and gamma-spodumene. The quartz-like phases were typically followed by spherulitic alkali feldspar-quartz intergrowths, euhedral petalite, and fine-grained muscovite. Nearly pure quartz formed as rims and replacement of metastable virgilite and stuffed quartz, in particular at the boron- and water-rich crystallization front of large feldspar or petalite. With the exception of muscovite, all minerals nucleated heterogeneously, on the capsule wall or on pre-existing minerals, and grew inwards, towards the capsule center. Experimental textures resembled the textures of zoned pegmatites, including skeletal, graphic, unidirectional, radiating, spherulitic, massive, and replacement textures. In some cases, when fluid saturation was reached, miarolitic cavities developed containing euhedral crystals. Although unidirectional growth rates appeared to slow down in time, volumetric rates for stable graphic alkali-feldspar quartz intergrowths and petalite remained constant for up to 60 days and similar to 70% crystallization. Metastable stuffed quartz and virgilite diminished in their growth rates in runs of 30 days or longer, were resorbed in the melt, and were partially replaced by second-generation quartz. Unobstructed, self-sustained crystal growth in conditions of very low nucleation density appears to be the dominant mechanism to form giant pegmatitic crystals, although experimental growth rates are much slower than predicted in nature based on conductive-cooling models.
Polyglycolide (PGA) is a biodegradable polymer with multiple applications in the medical sector. Here the synthesis of high molecular weight polyglycolide by ring-opening polymerization of diglycolide is reported. For the first time stabilizer free supercritical carbon dioxide (scCO(2)) was used as a reaction medium. scCO(2) allowed for a reduction in reaction temperature compared to conventional processes. Together with the lowering of monomer concentration and consequently reduced heat generation compared to bulk reactions thermal decomposition of the product occurring already during polymerization is strongly reduced. The reaction temperatures and pressures were varied between 120 and 150 degrees C and 145 to 1400 bar. Tin(II) ethyl hexanoate and 1-dodecanol were used as catalyst and initiator, respectively. The highest number average molecular weight of 31 200 g mol(-1) was obtained in 5 hours from polymerization at 120 degrees C and 530 bar. In all cases the products were obtained as a dry white powder. Remarkably, independent of molecular weight the melting temperatures were always at (219 +/- 2)degrees C.
Polyglycolide (PGA) is a biodegradable polymer with multiple applications in the medical sector. Here the synthesis of high molecular weight polyglycolide by ring-opening polymerization of diglycolide is reported. For the first time stabilizer free supercritical carbon dioxide (scCO2) was used as a reaction medium. scCO2 allowed for a reduction in reaction temperature compared to conventional processes. Together with the lowering of monomer concentration and consequently reduced heat generation compared to bulk reactions thermal decomposition of the product occurring already during polymerization is strongly reduced. The reaction temperatures and pressures were varied between 120 and 150 °C and 145 to 1400 bar. Tin(II) ethyl hexanoate and 1-dodecanol were used as catalyst and initiator, respectively. The highest number average molecular weight of 31 200 g mol−1 was obtained in 5 hours from polymerization at 120 °C and 530 bar. In all cases the products were obtained as a dry white powder. Remarkably, independent of molecular weight the melting temperatures were always at (219 ± 2) °C.
Trace element concentrations in aqueous fluids in equilibrium with haplogranitic melt were determined in situ at elevated P-T conditions using hydrothermal diamond-anvil cells and synchrotron-radiation XRF microanalyses. Time- resolved analyses showed that the Rb and Sr concentrations in the fluids became constant in less than 2000 s at all temperatures (500 to 780 degrees C). Although fluid-melt equilibration was very rapid, the change in the concentration of both elements in the fluid with temperature was fairly small (a slight increase for Rb and a slight decrease for Sr). This permitted partitioning data for Rb and Sr between haplogranitic melt and H2O or NaCl+KCl+HCl aqueous solutions at 750 degrees C and 200 to 700 MPa to be obtained from EMP analyses of the quenched melt and the in situ SR-XRF analyses of the equilibrated fluid. The resulting D-Rb(f/m) and D-Sr(f/m) were 0.01 +/- 0.002 and 0.006 +/- 0.001 for water as starting fluid, and increased to 0.47 +/- 0.08 and 0.23 +/- 0.03 for 3.56 m (NaCl+KCl)+0.04 in HCl at pressures of 224 to 360 MPa. In the experiments with H2O as starting fluid, the partition coefficients increased with pressure, i.e. D- Rb(f/m) from 0.01 +/- 0.002 to 0.22 +/- 0.02 and D-Sr(f/m) from 0.006 0.001 to 0.02 +/- 0.005 with a change in pressure from 360 to 700 MPa. At pressures to 360 MPa, the Rb/Sr ratio in the fluid was found to be independent of the initial salt concentration (Rb/Sr = 1.45 +/- 0.6). This ratio increased to 7.89 +/- 1.95 at 700 MPa in experiments with chloride free fluids, which indicates different changes in the Rb and Sr speciation with pressure.
Barium, lanthanum, ytterbium, and yttrium partitioning experiments between fluid-saturated haplogranitic melts and aqueous solutions were conducted at 750 to 950 degrees C and 0.2 to 1 GPa to investigate the effects of melt and fluid composition, pressure, and temperature. Partition coefficients were determined using different experimental methods. On one hand quenched experiments were performed, and on the other hand, trace element contents in the aqueous fluid were determined directly using a hydrothermal diamond-anvil cell and synchrotron radiation X-ray fluorescence microanalysis of K-lines. The latter required a high excitation energy of 50 key due to the high energies necessary to excite the K-lines of the studied elements. The data from these two techniques showed good agreement for chloridic solutions, whereas quenching had a significant effect on results of the experiments with only water in the case of Ba. In Cl-free experiments, lanthanum and yttrium, trace element contents were even below detection limit in the quenched fluids, whereas small concentrations were detected in comparable in-situ experiments. This distinct difference is likely due to back reactions between fluid and melt upon cooling. The partitioning data of all elements show no dependence on the temperature and only small dependence on pressure. In contrast, the partitioning is strongly influenced by the composition of the starting fluid and melt. For chloridic fluids, there was a sharp increase in the Ba, La, Y and Yb partition coefficients with the alumina saturation index (ASI). The Ba partition coefficient increased from 0.002 at an ASI of 0.8 to 0.55 at an ASI of 1.07. At higher ASI, it decreased slightly to 0.2 at an ASI of similar to 1.3. Likewise, it was one to two orders of magnitude higher in chloridic fluids compared to those found in H2O experiments. Fluid-melt partition coefficients of La and Y increased from 0.002 at an ASI of similar to 0.8 to similar to 0.1 at an ASI of 1.2. In the same ASI range, the Yb partition coefficient increased to a maximum value of 0.02. Even at high salinities all elements fractionate into the melt. The compositional dependence of the partitioning data imply that both melt composition and fluid composition have a strong influence on trace element behavior and that complexation of Ba. REE and Y tin the fluid is not only controlled by the presence of Cl- in the fluid. Instead, interaction of these elements with major melt components dissolved in the fluid is very likely.
Rubidium and strontium partitioning experiments between haplogranitic melts and aqueous fluids (water or 1.16- 3.56 m (NaCl + KCl) +/- HCl) were conducted at 750-950 degrees C and 0.2-1.4 GPa to investigate the effects of melt and fluid composition, pressure, and temperature. In addition, we studied if the applied technique (rapid and slow quench, and in-situ determination of trace element concentration in the fluid) has a bearing on the obtained data. There is good agreement of the data from different techniques for chloridic solutions, whereas back reactions between fluid and Melt upon cooling have a significant effect on results from the experiments with water. The Rb fluid-melt partition coefficient shows no recognizable dependence on melt composition and temperature. For chloridic Solutions, it is similar to 0.4, independent of pressure. In experiments with water, it is one to two orders of magnitude lower and increases with pressure. The strontium fluid-melt partition coefficient does not depend on temperature. It increases slightly with pressure in Cl free experiments. In chloridic fluids, there is a sharp increase in the Sr partition coefficient with the alumina saturation index (ASI) from 0.003 at an ASI of 0.8 to a maximum of 0.3 at an ASI of 1.05. At higher ASI, it decreases slightly to 0.2 at an ASI of 1.6. It is one to two orders of magnitude higher in chloridic fluids compared to those found in H2O experiments. The Rb/Sr ratio in non-chloridic solutions in equilibrium with metaluminous melts increases with pressure, whereas the Rb/Sr ratio in chloridic fluids is independent of pressure and decreases with fluid salinity. The obtained fluid-melt partition coefficients are in good agreement with data from natural cogenetic fluid and melt inclusions. Numerical modeling shows that although the Rb/Sr ratio in the residual melt is particularly sensitive to the degree of fractional crystallization, exsolution of a fluid phase, and associated fluid-melt partitioning is not a significant factor controlling Rb and Sr concentrations in the residual melt during crystallization of most granitoids.
Dynamics of solute export from catchments can be classified in terms of chemostatic and chemodynamic export regimes by an analysis of concentration-discharge relationships. Previous studies hypothesized that distinct export regimes emerge from the presence of solute mass stores within the catchment and their connectivity to the stream. However, so far a direct link of solute export to identifiable catchment characteristics is missing. Here we investigate long-term time series of stream water quality and quantity of nine neighboring catchments in Central Germany ranging from relatively pristine mountain catchments to agriculturally dominated lowland catchments, spanning large gradients in land use, geology, and climatic conditions. Given the strong collinearity of catchment characteristics we used partial least square regression analysis to quantify the predictive power of these characteristics for median concentrations and the metrics of export regime. We can show that median concentrations and metrics of the export regimes of major ions and nutrients can indeed be inferred from catchment characteristics. Strongest predictors for median concentrations were the share of arable land, discharge per area, runoff coefficient and available water capacity in the root zone of the catchments. The available water capacity in the root zone, the share of arable land being artificially drained and the topographic gradient were found to be the most relevant predictors for the metrics of export regime. These catchment characteristics can represent the size of solute mass store such as the fraction of arable land being a measure for the store of nitrate. On the other hand, catchment characteristics can be a measure for the connectivity of these solute stores to the stream such as the fraction of tile drained land in the catchments. This study demonstrates the potential of data-driven, top down analyses using simple metrics to classify and better understand dominant controls of solute export from catchments. (C) 2015 Elsevier Ltd. All rights reserved.