Refine
Has Fulltext
- yes (4)
Document Type
- Doctoral Thesis (4)
Language
- German (4) (remove)
Is part of the Bibliography
- yes (4)
Keywords
- Biosensor (4) (remove)
Institute
Diese Arbeit befasst sich mit der Herstellung und Charakterisierung von thermoresponsiven Filmen auf Goldelektroden durch Fixierung eines bereits synthetisierten thermoresponsiven Polymers. Als Basis für die Entwicklung der responsiven Grenzfläche dienten drei unterschiedliche Copolymere (Polymere I, II und III) aus der Gruppe der thermisch schaltbaren Poly(oligo(ethylenglykol)methacrylate).
Die turbidimetrischen Messungen der Copolymere in Lösungen haben gezeigt, dass der Trübungspunkt vom pH-Wert, der Gegenwart von Salzen sowie von der Ionenstärke der Lösung abhängig ist. Nach der Charakterisierung der Polymere in Lösung wurden Experimente der kovalenten Kopplung der Polymere I bis III an die Oberfläche der Gold-Elektroden durchgeführt. Während bei Polymeren I und II die Ankopplung auf einer Amidverbrückung basierte, wurde bei Polymer III als alternative Methode zur Immobilisierung eine photoinduzierte Anbindung unter gleichzeitiger Vernetzung gewählt. Der Nachweis der erfolgreichen Ankopplung erfolgte bei allen Polymeren elektrochemisch mittels Cyclovoltammetrie und Impedanzspektroskopie in K3/4[Fe(CN)6]-Lösungen. Wie die Ellipsometrie-Messungen zeigten, waren die erhaltenen Polymer-Filme unterschiedlich dick. Die Ankopplung über Amidverbrückung lieferte dünne Filme (10 – 15 nm), während der photovernetzte Film deutlich dicker war (70-80 nm) und die darunter liegende Oberfläche relativ gut isolierte.
Elektrochemische Temperaturexperimente an Polymer-modifizierten Oberflächen in Lösungen in Gegenwart von K3/4[Fe(CN)6] zeigten, dass auch die immobilisierten Polymere I bis III responsives Temperaturverhalten zeigen. Bei Elektroden mit den immobilisierten Polymeren I und II ist der Temperaturverlauf der Parameterwerte diskontinuierlich – ab einem kritischen Punkt (37 °C für Polymer I und 45 °C für Polymer II) wird zunächst langsame Zunahme der Peakströme wird deutlich schneller. Das Temperaturverhalten von Polymer III ist dagegen bis 50 °C kontinuierlich, der Peakstrom sinkt hier durchgehend.
Weiterhin wurde mit den auf Polymeren II und III basierten Elektroden deren Anwendung als responsive Matrix für Bioerkennungsreaktionen untersucht. Es wurde die Ankopplung von kleinen Biorezeptoren, TAG-Peptiden, an Polymer II- und Polymer III-modifizierten Elektroden durchgeführt. Das hydrophile FLAG-TAG-Peptid verändert das Temperaturverhalten des Polymer II-Films unwesentlich, da es die Hydrophilie des Netzwerkes nicht beeinflusst. Weiterhin wurde der Effekt der Ankopplung der ANTI-FLAG-TAG-Antikörper an FLAG-TAG-modifizierte Polymer II-Filme untersucht. Es konnte gezeigt werden, dass die Antikörper spezifisch an FLAG-TAG-modifiziertes Polymer II binden. Es wurde keine unspezifische Anbindung von ANTI-FLAG-TAG an Polymer II beobachtet. Die Temperaturexperimente haben gezeigt, dass die thermische Restrukturierung des Polymer II-FLAG-TAG-Filmes auch nach der Antikörper-Ankopplung noch stattfindet. Der Einfluss der ANTI-FLAG-TAG-Ankopplung ist gering, da der Unterschied in der Hydrophilie zwischen Polymer II und FLAG-TAG bzw. ANTI-FLAG-TAG zu gering ist.
Für die Untersuchungen mit Polymer III-Elektroden wurde neben dem hydrophilen FLAG-TAG-Peptid das deutlich hydrophobere HA-TAG-Peptid ausgewählt. Wie im Falle der Polymer II Elektrode beeinflusst das gekoppelte FLAG-TAG-Peptid das Temperaturverhalten des Polymer III-Netzwerkes nur geringfügig. Die gemessenen Stromwerte sind geringer als bei der Polymer III-Elektrode. Das Temperaturverhalten der FLAG-TAG-Elektrode ähnelt dem der reinen Polymer III-Elektrode – die Stromwerte sinken kontinuierlich bis die Temperatur von ca. 40 °C erreicht ist, bei der ein Plateau beobachtet wird. Offensichtlich verändert FLAG-TAG auch in diesem Fall nicht wesentlich die Hydrophilie des Polymer III-Netzwerkes. Das an Polymer III-Elektroden gekoppelte hydrophobe HA-TAG-Peptid beeinflusst dagegen im starken Maße den Quellzustand des Netzwerkes. Die Ströme für die HA-TAG-Elektroden sind deutlich geringer als die für die FLAG-TAG-Polymer III-Elektroden, was auf geringeren Wassergehalt und dickeren Film zurückzuführen ist. Bereits ab 30 °C erfolgt der Anstieg von Stromwerten, der bei Polymer III- bzw. bei Polymer III-FLAG-TAG-Elektroden nicht beobachtet werden kann. Das gekoppelte hydrophobe HA-TAG-Peptid verdrängt Wasser aus dem Polymer III-Netzwerk, was in der Stauchung des Films bereits bei Raumtemperatur resultiert. Dies führt dazu, dass der Film im Laufe des Temperaturanstieges kaum noch komprimiert. Die Stromwerte steigen in diesem Fall entsprechend des Anstiegs der temperaturabhängigen Diffusion des Redoxpaares. Diese Untersuchungen zeigen, dass das HA-TAG-Peptid als Ankermolekül deutlich besser für eine potentielle Verwendung der Polymer III-Filme für sensorische Zwecke geeignet ist, da es sich deutlich in der Hydrophilie von Polymer III unterscheidet.
Das Influenzavirus infiziert Säugetiere und Vögel. Der erste Schritt im Infektionszyklus ist die Anbindung des Viruses über sein Oberflächenprotein Hämagglutinin (HA) an Zuckerstrukturen auf Epithelzellen des respiratorischen Traktes im Wirtsorganismus. Aus den drei komplementaritätsbestimmenden Regionen (complementarity determining regions, CDRs) der schweren Kette eines monoklonalen Hämagglutinin-bindenden Antikörpers wurden drei lineare Peptide abgeleitet. Die Bindungseigenschaften der drei Peptide wurden experimentell mittels Oberflächenplasmonenresonanzspektroskopie untersucht. Es zeigte sich, dass in Übereinstimmung mit begleitenden Molekulardynamik-Simulationen zwei der drei Peptide (PeB und PeC) analog zur Bindefähigkeit des Antikörpers in der Lage sind, Influenzaviren vom Stamm X31 (H3N2 A/Aichi/2/1968) zu binden. Die Interaktion des Peptids PeB, welches potentiell mit der konservierten Rezeptorbindestelle im HA interagiert, wurde anschließend näher charakterisiert. Die Detektion der Influenzaviren war unter geeigneten Immobilisationsbedingungen im diagnostisch relevanten Bereich möglich. Die Spezifität der PeB-Virus-Bindung wurde mittels geeigneter Kontrollen auf der Seite des Analyten und des Liganden nachgewiesen. Des Weiteren war das Peptid PeB in der Lage die Bindung von X31-Viren an Mimetika seines natürlichen Rezeptors zu inhibieren, was die spezifische Interaktion mit der Rezeptorbindungsstelle im Hämagglutinin belegt. Anschließend wurde die Primärsequenz von PeB durch eine vollständige Substitutionsanalyse im Microarray-Format hinsichtlich der Struktur-Aktivitäts-Beziehungen charakterisiert. Dies führte außerdem zu verbesserten Peptidvarianten mit erhöhter Affinität und breiterer Spezifität gegen aktuelle Influenzastämme verschiedener Serotypen (z.B. H1N1/2009, H5N1/2004, H7N1/2013). Schließlich konnte durch Verwendung einer in der Primärsequenz angepassten höher affinen Peptidvariante die Influenzainfektion in vitro inhibiert werden. Damit stellen die vom ursprünglichen Peptid PeB abgeleiteten Varianten Rezeptormoleküle in biosensorischen Testsystemen sowie potentielle Wirkstoffe dar.
Biosensoren werden oft für die Messung einzelner Substanzen in komplexen Medien verwendet, wie z.B. bei der Blutzuckerbestimmung. Sie bestehen aus einem physikochemischen Sensor, dem Transduktionselement, und einer darauf immobilisierten biologischen Komponente, dem Erkennungselement. In dieser Arbeit wurde als Transduktionselement eine Elektrode und als Biokomponente das Enzym „Meerrettich Peroxidase“ (engl. horseradish peroxidase, HRP) verwendet. Solche HRP-Elektroden werden für die Messung von Wasserstoffperoxid (H2O2) eingesetzt. H2O2 wird im Körper von weißen Blutkörperchen produziert, um Bakterien abzutöten, wird teilweise ausgeatmet und kann in kondensierter Atemluft nachgewiesen werden. Da viele weiße Blutkörperchen bei einer Chemotherapie abgetötet und dadurch die Patienten anfälliger für Infektionen werden, muss ihre Anzahl regelmäßig überwacht werden. Dazu wird zurzeit Blut abgenommen. Im ersten Teil dieser Arbeit wurde untersucht, ob eine Überwachung der Anzahl an weißen Blutkörperchen ohne Blutabnahme durch eine H2O2-Messung erfolgen kann. Ein direkter Zusammenhang zwischen der ausgeatmeten H2O2-Menge und der Zahl der weißen Blutkörperchen konnte dabei nicht festgestellt werden. Für empfindliche H2O2-Messungen mit einer HRP-Elektrode ist ein schneller Austausch von Elektronen zwischen der Elektrode und dem Enzym notwendig. Eine Vorraussetzung dafür ist eine kurze Distanz zwischen dem aktiven Zentrum des Enzyms und der Elektrodenoberfläche. Um einen kurzen Abstand zu erreichen wurden im zweiten Teil dieser Arbeit verschiedene poröse graphitähnliche Materialien aus pyrolysierten Kobalt-Porphyrinen für die Elektrodenherstellung verwendet. Dabei stellte sich heraus, dass eines der untersuchten Materialien, welches Poren von etwa der Größe eines Enzyms hat, Elektronen etwa 200mal schneller mit dem Enzym austauscht als festes Graphit. Die HRP selbst enthält in seinem aktiven Zentrum ein Eisen-Protoporphyrin, also ein aus vier Ringen bestehendes flaches Molekül mit einem Eisenatom im Zentrum. Reagiert die HRP mit H2O2, so entzieht es dem Peroxid zwei Elektronen. Eines dieser Elektronen wird am Eisen, das andere im Ringsystem zwischengespeichert, bevor sie an ein anderes Molekül oder an die Elektrode weitergegeben werden. Im letzten Teil dieser Arbeit wurde das Eisen durch Osmium ausgetauscht. Das so veränderte Enzym entzieht Peroxiden nur noch ein Elektron. Dadurch reagiert es zwar langsamer mit Wasserstoffperoxid, dafür aber schneller mit tert-Butylhydroperoxid, einem organischen Vertreter der Peroxid-Familie.
Das Superoxidradikal kann mit fast allen Bestandteilen von Zellen reagieren und diese schädigen. Die medizinische Forschung stellte eine Beteiligung des Radikals an Krebs, Herzinfarkten und neuraler Degeneration fest. Ein empfindlicher Superoxidnachweis ist daher zum besseren Verständnis von Krankheitsverläufen wichtig. Dabei stellen die geringen typischen Konzentrationen und seine kurze Lebensdauer große Anforderungen. Ziel dieser Arbeit war es zum einen, zwei neuartige Proteinarchitekturen auf Metallelektroden zu entwickeln und deren elektrochemisches Ansprechverhalten zu charakterisieren. Zum anderen waren diese Elektroden zur empfindlichen quantitativen Superoxiddetektion einzusetzen. Im ersten Teil der Arbeit wurde eine Protein-Multischichtelektrode aus Cytochrom c und dem Polyelektrolyten Poly(anilinsulfonsäure) nach dem Layer-by-layer-Verfahren aufgebaut. Für zwei bis 15 Schichten an Protein wurde eine deutliche Zunahme an elektrodenaktivem Cytochrom c mit jedem zusätzlichen Aufbringungsschritt nachgewiesen. Die Zunahme verlief linear und ergab bei 15 Schichten eine Zunahme der redoxaktiven Proteinmenge um deutlich mehr als eine Größenordnung. Während das formale Potential im Multischichtsystem sich im Vergleich zur Monoschichtelektrode nicht veränderte, wurde für die Kinetik eine Abhängigkeit der Geschwindigkeit des Elektronentransfers von der Zahl der Proteinschichten beobachtet. Mit zunehmender Scangeschwindigkeit trat ein reversibler Kontaktverlust zu den äußeren Schichten auf. Die lineare Zunahme an elektroaktivem Protein mit steigender Zahl an Depositionsschritten unterscheidet sich deutlich von in der Literatur beschriebenen Protein/Polyelektrolyt-Multischichtelektroden, bei denen ab etwa 6-8 Schichten keine Zunahme an elektroaktivem Protein mehr festgestelltwurde. Auch ist bei diesen die Zunahme an kontaktierbaren Proteinmolekülen auf das Zwei- bis Fünffache limitiert. Diese Unterschiede des neu vorgestellten Systems zu bisherigen Multischichtassemblaten erklärt sich aus einem in dieser Arbeit für derartige Systeme erstmals beschriebenen Elektronentransfermechanismus. Der Transport von Elektronen zwischen der Elektrodenoberfläche und den Proteinmolekülen in den Schichten verläuft über einen Protein-Protein-Elektronenaustausch. Dieser Mechanismus beruht auf dem schnellen Selbstaustausch von Cytochrom c-Molekülen und einer verbleibenden Rotationsflexibilität des Proteins im Multischichtsystem. Die Reduzierung des Proteins durch das Superoxidradikal und eine anschließende Reoxidation durch die Elektrode konnten nachgewiesen werden. In einem amperometrischen Messansatz wurde das durch Superoxidradikale hervorgerufene elektrochemische Signal in Abhängigkeit von der Zahl an Proteinschichten gemessen. Ein maximales Ansprechverhalten auf das Radikal wurde mit 6-Schichtelektroden erzielt. Die Empfindlichkeit der 6-Schichtelektroden wurde im Vergleich zum Literaturwert der Monoschichtelektrode um Faktor 14, also mehr als eine Größenordnung, verbessert. Somit konnte eine Elektrode mit 6 Schichten aus Cytochrom c und Poly(anilinsulfonsäure) als neuartiger Superoxidsensor mit einer 14-fachen Verbesserung der Empfindlichkeit im Vergleich zum bislang benutzten System entwickelt werden. Der zweite Teil dieser Arbeit beschreibt die Auswahl, Gewinnung und Charakterisierung von Mutanten des Proteins Cu,Zn-Superoxiddismutase zur elektrochemischen Quantifizierung von Superoxidradikalen. Monomere Mutanten des humanen dimeren Enzyms wurden entworfen, die durch Austausch von Aminosäuren ein oder zwei zusätzliche Cysteinreste besaßen, mit welchem sie direkt auf der Goldelektrodenoberfläche chemisorbieren sollten. 6 derartige Mutanten konnten in ausreichender Menge und Reinheit in aktiver Form gewonnen werden. Die Bindung der Superoxiddismutase-Mutanten an Goldoberflächen konnte durch Oberflächen-plasmonresonanz und Impedanzspektroskopie nachgewiesen werden. Alle Mutanten wiesen einen quasi-reversiblen Elektronentransfer zwischen SOD und Elektrode auf. Durch Untersuchung von kupferfreien SOD-Mutanten sowie des Wildtyps konnte nachgewiesen werden, das die Mutanten über die eingefügten Cysteinreste auf der Elektrode chemisorptiv gebunden wurden und der Elektronentransfer zwischen der Elektrode und dem Kupfer im aktiven Zentrum der SOD erfolgte. Die Superoxiddismutase katalysiert die Zersetzung von Superoxidmolekülen durch Oxidation und durch Reduktion der Radikale. Somit sind beide Teilreaktionen von analytischem Interesse. Zyklovoltammetrisch konnte sowohl die Oxidation als auch die Reduktion des Radikals durch die immobilisierten Superoxiddismutase-Mutanten nachgewiesen werden. In amperometrischen Messanordnungen konnten beide Teilreaktionen zur analytischen Quantifizierung von Superoxidradikalen genutzt werden. Im positiven Potentialfenster wurde die Empfindlichkeit um einen Faktor von etwa 10 gegenüber der Cytochrom c–Monoschichtelektrode verbessert.