Refine
Document Type
- Article (5)
- Doctoral Thesis (1)
Language
- English (6)
Is part of the Bibliography
- yes (6)
Keywords
- AFM (6) (remove)
Institute
The thermal behavior of poly(methoxydiethylenglycol acrylate) (PMDEGA) is studied in thin hydrogel films on solid supports and is compared with the behavior in aqueous solution. The PMDEGA hydrogel film thickness is varied from 2 to 422 nm. Initially, these films are homogenous, as measured with optical microscopy, atomic force microscopy, X-ray reflectivity, and grazing-incidence small-angle X-ray scattering (GISAXS). However, they tend to de-wet when stored under ambient conditions. Along the surface normal, no long-ranged correlations between substrate and film surface are detected with GISAXS, due to the high mobility of the polymer at room temperature. The swelling of the hydrogel films as a function of the water vapor pressure and the temperature are probed for saturated water vapor pressures between 2,380 and 3,170 Pa. While the swelling capability is found to increase with water vapor pressure, swelling in dependence on the temperature revealed a collapse phase transition of a lower critical solution temperature type. The transition temperature decreases from 40.6 A degrees C to 36.6 A degrees C with increasing film thickness, but is independent of the thickness for very thin films below a thickness of 40 nm. The observed transition temperature range compares well with the cloud points observed in dilute (0.1 wt.%) and semi-dilute (5 wt.%) solution which decrease from 45 A degrees C to 39 A degrees C with increasing concentration.
The correlations between the chemical structures of the 2,5-diphenyl-1,3,4-oxadiazole compounds and their corresponding vapour deposited film structures on Si/SiO2 were systematically investigated with AFM, XSR and IR for the first time. The result shows that the film structure depends strongly on the substrate temperature (Ts). For the compounds with ether bridge group, the film periodicity depends linearly on the length of the aliphatic chain. The films based on those oxadiazols have ordered structure in the investigated substrate temperature region, while die amide bridged compounds form ordered film only at high Ts due to the formation of intermolecular H-bond. The tilt angle of most molecules is determined by the pi-pi complexes between the molecules. The intermolecular interaction between head groups leads to the structural transformation during the thermal treatment after deposition. All the ether bridged oxadiazoles form films with bilayer structure, while amide bridged oxadiazole form film bilayer structure only when the molecule has a head group.
We use a dynamic scanning electron microscope (DySEM) to map the spatial distribution of the vibration of a cantilever beam. The DySEM measurements are based on variations of the local secondary electron signal within the imaging electron beam diameter during an oscillation period of the cantilever. For this reason, the surface of a cantilever without topography or material variation does not allow any conclusions about the spatial distribution of vibration due to a lack of dynamic contrast. In order to overcome this limitation, artificial structures were added at defined positions on the cantilever surface using focused ion beam lithography patterning. The DySEM signal of such high-contrast structures is strongly improved, hence information about the surface vibration becomes accessible. Simulations of images of the vibrating cantilever have also been performed. The results of the simulation are in good agreement with the experimental images.
The new 3,4-propylenedioxythiophenes (ProDOT) bearing hydroxy- or chloro-functionalized side chains of varying length and polarity were synthesized and electropolymerized on single carbon fiber microelectrode (SCFME) using cyclo-voltammetry. Electrochemical impedance spectroscopy (EIS) revealed highest capacitance values for the hydroxy-functionalized Poly 5 carrying a side chain of medium length. The EIS data were fitted with an equivalent electrical circuit giving a good correlation. AFM analysis of the topography showed higher roughness values for Poly 5 than for the two other polymers bearing longer side chains. Due to their reactive end groups the polymers should be useful for post-polymerization functionalization of the electrode surface.
In this paper we report on the interaction between photosensitive azobenzene-containing polymer films and on top adsorbed graphene multilayers. The photosensitive polymer film changes its topography under irradiation with light interference patterns according to their polarization distribution. The multilayer graphene follows the deformation of the polymer film and stretches accordingly. Using confocal Raman microspectroscopy we can detect the appearance of additional peaks in the Raman spectrum of the photosensitive polymer film upon irradiation indicating a molecular interaction at the interface between the graphene multilayer and the polymer matrix. Multi-component analysis of the specific Raman bands shows that the interaction involves the graphene rings and the aromatic rings of the azobenzenes causing the strong adhesion between the two materials.