Refine
Document Type
- Article (17)
- Other (4)
- Postprint (3)
- Monograph/Edited Volume (1)
- Review (1)
Is part of the Bibliography
- yes (26)
Keywords
- PHREEQC (6)
- reactive transport (6)
- digital rock physics (4)
- elastic properties (3)
- heterogeneity (3)
- micro-CT (3)
- numerical simulation (3)
- Code_Aster (2)
- Mont Terri (2)
- carbon dioxide (2)
Institute
Barite stands out as one of the most ubiquitous scaling agents in deep geothermal systems, responsible for irreversible efficiency loss. Due to complex parameter interplay, it is imperative to utilise numerical simulations to investigate temporal and spatial precipitation effects. A one-dimensional reactive transport model is set up with heterogeneous nucleation and crystal growth kinetics. In line with geothermal systems in the North German Basin, the following parameters are considered in a sensitivity analysis: temperature (25 to 150 degrees C), pore pressure (10 to 50 MPa), fracture aperture (10(-4) to 10(-2) m), flow velocity (10(-3) to 10(0) m s(-1)), molar volume (50.3 to 55.6 cm(3) mol(-1)), contact angle for heterogeneous nucleation (0 degrees to 180 degrees), interfacial tension (0.07 to 0.134 J m(-2)), salinity (0.1 to 1.5 mol kgw(-1) NaCl), pH (5 to 7), and supersaturation ratio (1 to 30). Nucleation and consequently crystal growth can only begin if the threshold supersaturation is exceeded, therefore contact angle and interfacial tension are the most sensitive in terms of precipitation kinetics. If nucleation has occurred, crystal growth becomes the dominant process, which is mainly controlled by fracture aperture. Results show that fracture sealing takes place within months (median 33 days) and the affected range can be on the order of tens of metres (median 10 m). The presented models suggest that barite scaling must be recognised as a serious threat if the supersaturation threshold is exceeded, in which case, large fracture apertures could help to minimise kinetic rates. The models further are of use for adjusting the fluid injection temperature.
Water management tools are necessary to guarantee the preservation of natural resources while ensuring optimum utilization. Linear regression models are a simple and quick solution for creating prognostic capabilities. Multivariate models show higher precision than univariate models. In the case of Waiwera, implementation of individual production rates is more accurate than applying just the total production rate. A maximum of approximately 1,075 m3/day can be pumped to ensure a water level of at least 0.5 m a.s.l. in the monitoring well. The model should be renewed annually to implement new data and current water level trends to keep the quality.
Integration and development of the energy supply in China and worldwide is a challenge for the years to come. The innovative idea presented here is based on an extension of the “power-to-gas-to-power” technology by establishing a closed carbon cycle. It is an implementation of a low-carbon energy system based on carbon dioxide capture and storage (CCS) to store and reuse wind and solar energy. The Chenjiacun storage project in China compares well with the German case study for the towns Potsdam and Brandenburg/Havel in the Federal State of Brandenburg based on the Ketzin pilot site for CCS.
Power-to-gas (PtG) stores chemical energy by converting excess electrical energy from renewable sources into an energy-dense gas. Due to its higher available capacity compared to surface-based storage technologies, subsurface storage in geological systems is the most promising approach for efficient and economic realization of the PtG system’s storage component. For this purpose, methane (CH4) produced by methanation by means of hydrogen (H2) and carbon dioxide (CO2) is stored in a geological reservoir until required for further use. In this context, CO2 is used as the cushion gas to maintain reservoir pressure and limiting working gas, i.e., (CH4) losses during withdrawal periods. Consequently, mixing of both gases in the reservoir is inevitable. Therefore, it is necessary to minimize the gas mixing region to optimize the efficiency of the PtG system’s storage component. In the present study, the physical properties of CH4, CO2 and their mixtures are reviewed. Then, a multicomponent flow model is implemented and validated against published data. Next, a hydromechanically coupled model is established, considering fluid flow through porous media and effective stresses to investigate the mixing behavior of both gases and the mechanical reservoir stability. The simulation results show that, with increasing reservoir thickness and dip angle, the mixing region is reduced during gas injection if CO2 is employed as the cushion gas. In addition, the degree of mixing is lower at higher temperatures. Feasible injection rates and injection schedules can be derived from the integrated reservoir stability analysis. The methodology developed in the present study allows the determination of optimum strategies for storage reservoir selection and gas injection scheduling by minimizing the gas mixing region.
Geochemical processes change the microstructure of rocks and thereby affect their physical behaviour at the macro scale. A micro-computer tomography (micro-CT) scan of a typical reservoir sandstone is used to numerically examine the impact of three spatial alteration patterns on pore morphology, permeability and elastic moduli by correlating precipitation with the local flow velocity magnitude. The results demonstrate that the location of mineral growth strongly affects the permeability decrease with variations by up to four orders in magnitude. Precipitation in regions of high flow velocities is characterised by a predominant clogging of pore throats and a drastic permeability reduction, which can be roughly described by the power law relation with an exponent of 20. A continuous alteration of the pore structure by uniform mineral growth reduces the permeability comparable to the power law with an exponent of four or the Kozeny-Carman relation. Preferential precipitation in regions of low flow velocities predominantly affects smaller throats and pores with a minor impact on the flow regime, where the permeability decrease is considerably below that calculated by the power law with an exponent of two. Despite their complete distinctive impact on hydraulics, the spatial precipitation patterns only slightly affect the increase in elastic rock properties with differences by up to 6.3% between the investigated scenarios. Hence, an adequate characterisation of the spatial precipitation pattern is crucial to quantify changes in hydraulic rock properties, whereas the present study shows that its impact on elastic rock parameters is limited. The calculated relations between porosity and permeability, as well as elastic moduli can be applied for upscaling micro-scale findings to reservoir-scale models to improve their predictive capabilities, what is of paramount importance for a sustainable utilisation of the geological subsurface.
How insoluble inclusions and intersecting layers affect the leaching process within potash seams
(2021)
Potash seams are a valuable resource containing several economically interesting, but also highly soluble minerals. In the presence of water, uncontrolled leaching can occur, endangering subsurface mining operations. In the present study, the influence of insoluble inclusions and intersecting layers on leaching zone evolution was examined by means of a reactive transport model. For that purpose, a scenario analysis was carried out, considering different rock distributions within a carnallite-bearing potash seam. The results show that reaction-dominated systems are not affected by heterogeneities at all, whereas transport-dominated systems exhibit a faster advance in homogeneous rock compositions. In return, the ratio of permeated rock in vertical direction is higher in heterogeneous systems. Literature data indicate that most natural potash systems are transport-dominated. Accordingly, insoluble inclusions and intersecting layers can usually be seen as beneficial with regard to reducing hazard potential as long as the mechanical stability of leaching zones is maintained. Thereby, the distribution of insoluble areas is of minor impact unless an inclined, intersecting layer occurs that accelerates leaching zone growth in one direction. Moreover, it is found that the saturation dependency of dissolution rates increases the growth rate in the long term, and therefore must be considered in risk assessments.
Injection of fluids into deep saline aquifers causes a pore pressure increase in the storage formation, and thus displacement of resident brine. Via hydraulically conductive faults, brine may migrate upwards into shallower aquifers and lead to unwanted salinisation of potable groundwater resources. In the present study, we investigated different scenarios for a potential storage site in the Northeast German Basin using a three-dimensional (3-D) regional-scale model that includes four major fault zones. The focus was on assessing the impact of fault length and the effect of a secondary reservoir above the storage formation, as well as model boundary conditions and initial salinity distribution on the potential salinisation of shallow groundwater resources. We employed numerical simulations of brine injection as a representative fluid.
Our simulation results demonstrate that the lateral model boundary settings and the effective fault damage zone volume have the greatest influence on pressure build-up and development within the reservoir, and thus intensity and duration of fluid flow through the faults. Higher vertical pressure gradients for short fault segments or a small effective fault damage zone volume result in the highest salinisation potential due to a larger vertical fault height affected by fluid displacement. Consequently, it has a strong impact on the degree of shallow aquifer salinisation, whether a gradient in salinity exists or the saltwater-freshwater interface lies below the fluid displacement depth in the faults. A small effective fault damage zone volume or low fault permeability further extend the duration of fluid flow, which can persist for several tens to hundreds of years, if the reservoir is laterally confined. Laterally open reservoir boundaries, large effective fault damage zone volumes and intermediate reservoirs significantly reduce vertical brine migration and the potential of freshwater salinisation because the origin depth of displaced brine is located only a few decametres below the shallow aquifer in maximum.
The present study demonstrates that the existence of hydraulically conductive faults is not necessarily an exclusion criterion for potential injection sites, because salinisation of shallower aquifers strongly depends on initial salinity distribution, location of hydraulically conductive faults and their effective damage zone volumes as well as geological boundary conditions.
Injection of fluids into deep saline aquifers causes a pore pressure increase in the storage formation, and thus displacement of resident brine. Via hydraulically conductive faults, brine may migrate upwards into shallower aquifers and lead to unwanted salinisation of potable groundwater resources. In the present study, we investigated different scenarios for a potential storage site in the Northeast German Basin using a three-dimensional (3-D) regional-scale model that includes four major fault zones. The focus was on assessing the impact of fault length and the effect of a secondary reservoir above the storage formation, as well as model boundary conditions and initial salinity distribution on the potential salinisation of shallow groundwater resources. We employed numerical simulations of brine injection as a representative fluid. Our simulation results demonstrate that the lateral model boundary settings and the effective fault damage zone volume have the greatest influence on pressure build-up and development within the reservoir, and thus intensity and duration of fluid flow through the faults. Higher vertical pressure gradients for short fault segments or a small effective fault damage zone volume result in the highest salinisation potential due to a larger vertical fault height affected by fluid displacement. Consequently, it has a strong impact on the degree of shallow aquifer salinisation, whether a gradient in salinity exists or the saltwater-freshwater interface lies below the fluid displacement depth in the faults. A small effective fault damage zone volume or low fault permeability further extend the duration of fluid flow, which can persist for several tens to hundreds of years, if the reservoir is laterally confined. Laterally open reservoir boundaries, large effective fault damage zone volumes and intermediate reservoirs significantly reduce vertical brine migration and the potential of freshwater salinisation because the origin depth of displaced brine is located only a few decametres below the shallow aquifer in maximum. The present study demonstrates that the existence of hydraulically conductive faults is not necessarily an exclusion criterion for potential injection sites, because salinisation of shallower aquifers strongly depends on initial salinity distribution, location of hydraulically conductive faults and their effective damage zone volumes as well as geological boundary conditions.
Every year, the European Geosciences Union (EGU) brings together experts from all over the world at its General Assembly, covering all disciplines of the Earth, planetary and space sciences. The EGU Division on Energy, Resources and the Environment (ERE) is concerned with one of the humankind's most challenging goals – providing affordable, reliable and sustainable energy and other georesources. A collection of contributions from the ERE Division at the EGU General Assembly 2018 is assembled within the present special issue in Advances in Geosciences.
Dissolved CO2 storage in geological formations with low pressure, low risk and large capacities
(2017)
Geological CO2 storage is a mitigation technology to reduce CO2 emissions from fossil fuel combustion. However, major concerns are the pressure increase and saltwater displacement in the mainly targeted deep groundwater aquifers due to injection of supercritical CO2. The suggested solution is storage of CO2 exclusively in the dissolved state. In our exemplary regional case study of the North East German Basin based on a highly resolved temperature and pressure distribution model and a newly developed reactive transport coupling, we have quantified that 4.7 Gt of CO2 can be stored in solution compared to 1.5 Gt in the supercritical state.