660 Chemische Verfahrenstechnik
Refine
Is part of the Bibliography
- yes (19)
Keywords
- perovskite solar cells (3)
- photoluminescence (3)
- non-radiative interface recombination (2)
- photochemistry (2)
- 2101 duplex stainless steel (1)
- Air (1)
- Arsenic speciation (1)
- Bacteria (1)
- China (1)
- CrNx coatings (1)
Institute
- Institut für Physik und Astronomie (6)
- Institut für Chemie (5)
- Mathematisch-Naturwissenschaftliche Fakultät (4)
- Institut für Geowissenschaften (3)
- Extern (1)
- Fachgruppe Politik- & Verwaltungswissenschaft (1)
- Institut für Ernährungswissenschaft (1)
- Institut für Umweltwissenschaften und Geographie (1)
- Öffentliches Recht (1)
Die Femtosekundendynamik nach resonanten Photoanregungen mit optischen und Röntgenpulsen ermöglicht eine selektive Verformung von chemischen N‐H‐ und N‐C‐Bindungen in 2‐Thiopyridon in wässriger Lösung. Die Untersuchung der orbitalspezifischen elektronischen Struktur und ihrer Dynamik auf ultrakurzen Zeitskalen mit resonanter inelastischer Röntgenstreuung an der N1s‐Resonanz am Synchrotron und dem Freie‐Elektronen‐Laser LCLS in Kombination mit quantenchemischen Multikonfigurationsberechnungen erbringen den direkten Nachweis dieser kontrollierten photoinduzierten Molekülverformungen und ihrer ultrakurzen Zeitskala.
The ultrafast photo-induced ring opening of the oxirane derivative trans-stilbene oxide has been studied through the use of ultrafast UV/UV pump-probe spectroscopy by using photo-ion detection. Single- and multiphoton probe paths and final states were identified through comparisons between UV power studies and synchrotron-based vacuum ultraviolet (VUV) single-photon ionization studies. Three major time-dependent features of the parent ion (sub-450 fs decay, (1.5 +/- 0.2) ps, and >100 ps) were observed. These decays are discussed in conjunction with the primary ring-opening mechanism of stilbene oxide, which occurs through C-C dissociation in the oxirane ring. The appearance of fragments relating to the masses of dehydrogenated diphenylmethane (167 amu) and dehydrogenated methylbenzene (90 amu) were also investigated. The appearance of the 167 amu fragment could suggest an alternative ultrafast ring-opening pathway via the dissociation of one of the C-O bonds within the oxirane ring.
The femtosecond excited-state dynamics following resonant photoexcitation enable the selective deformation of N-H and N-C chemical bonds in 2-thiopyridone in aqueous solution with optical or X-ray pulses. In combination with multiconfigurational quantum-chemical calculations, the orbital-specific electronic structure and its ultrafast dynamics accessed with resonant inelastic X-ray scattering at the N 1s level using synchrotron radiation and the soft X-ray free-electron laser LCLS provide direct evidence for this controlled photoinduced molecular deformation and its ultrashort time-scale.
Arsenic can occur in foods as inorganic and organic forms. Inorganic arsenic is more toxic than most watersoluble organic arsenic compounds such as arsenobetaine, which is presumed to be harmless for humans. Within the first German total diet study, total arsenic, inorganic arsenic, arsenobetaine, dimethylarsinic acid and monomethylarsonic acid were analyzed in various foods. Highest levels of total arsenic were found in fish, fish products and seafood (mean: 1.43 mg kg(-1); n = 39; min-max: 0.01-6.15 mg kg(-1)), with arsenobetaine confirmed as the predominant arsenic species (1.233 mg kg 1; n = 39; min-max: 0.01-6.23 mg kg (1)). In contrast, inorganic arsenic was determined as prevalent arsenic species in terrestrial foods (0.02 mg kg (1); n = 38; min-max: 0-0.11 mg kg (1)). However, the toxicity of arsenic species varies and measurements are necessary to gain information about the composition and changes of arsenic species in foods due to household processing of foods.
While the problem of the identification of mechanisms of hydrogen-assisted damage has and is being thoroughly studied, the quantitative analysis of such damage still lacks suitable tools. In fact, while, for instance, electron microscopy yields excellent characterization, the quantitative analysis of damage requires at the same time large field-of-views and high spatial resolution. Synchrotron X-ray refraction techniques do possess both features. Herein, it is shown how synchrotron X-ray refraction computed tomography (SXRCT) can quantify damage induced by hydrogen embrittlement in a lean duplex steel, yielding results that overperform even those achievable by synchrotron X-ray absorption computed tomography. As already reported in the literature, but this time using a nondestructive technique, it is shown that the hydrogen charge does not penetrate to the center of tensile specimens. By the comparison between virgin and hydrogen-charged specimens, it is deduced that cracks in the specimen bulk are due to the rolling process rather than hydrogen-assisted. It is shown that (micro)cracks propagate from the surface of tensile specimens to the interior with increasing applied strain, and it is deduced that a significant crack propagation can only be observed short before rupture.
The increasing development of antibiotic resistance in bacteria has been a major problem for years, both in human and veterinary medicine. Prophylactic measures, such as the use of vaccines, are of great importance in reducing the use of antibiotics in livestock. These vaccines are mainly produced based on formaldehyde inactivation. However, the latter damages the recognition elements of the bacterial proteins and thus could reduce the immune response in the animal. An alternative inactivation method developed in this work is based on gentle photodynamic inactivation using carbon nanodots (CNDs) at excitation wavelengths λex > 290 nm. The photodynamic inactivation was characterized on the nonvirulent laboratory strain Escherichia coli K12 using synthesized CNDs. For a gentle inactivation, the CNDs must be absorbed into the cytoplasm of the E. coli cell. Thus, the inactivation through photoinduced formation of reactive oxygen species only takes place inside the bacterium, which means that the outer membrane is neither damaged nor altered. The loading of the CNDs into E. coli was examined using fluorescence microscopy. Complete loading of the bacterial cells could be achieved in less than 10 min. These studies revealed a reversible uptake process allowing the recovery and reuse of the CNDs after irradiation and before the administration of the vaccine. The success of photodynamic inactivation was verified by viability assays on agar. In a homemade flow photoreactor, the fastest successful irradiation of the bacteria could be carried out in 34 s. Therefore, the photodynamic inactivation based on CNDs is very effective. The membrane integrity of the bacteria after irradiation was verified by slide agglutination and atomic force microscopy. The method developed for the laboratory strain E. coli K12 could then be successfully applied to the important avian pathogens Bordetella avium and Ornithobacterium rhinotracheale to aid the development of novel vaccines.
Perovskite solar cells combine high carrier mobilities with long carrier lifetimes and high radiative efficiencies. Despite this, full devices suffer from significant nonradiative recombination losses, limiting their VOC to values well below the Shockley–Queisser limit. Here, recent advances in understanding nonradiative recombination in perovskite solar cells from picoseconds to steady state are presented, with an emphasis on the interfaces between the perovskite absorber and the charge transport layers. Quantification of the quasi‐Fermi level splitting in perovskite films with and without attached transport layers allows to identify the origin of nonradiative recombination, and to explain the VOC of operational devices. These measurements prove that in state‐of‐the‐art solar cells, nonradiative recombination at the interfaces between the perovskite and the transport layers is more important than processes in the bulk or at grain boundaries. Optical pump‐probe techniques give complementary access to the interfacial recombination pathways and provide quantitative information on transfer rates and recombination velocities. Promising optimization strategies are also highlighted, in particular in view of the role of energy level alignment and the importance of surface passivation. Recent record perovskite solar cells with low nonradiative losses are presented where interfacial recombination is effectively overcome—paving the way to the thermodynamic efficiency limit.
Modular toolkit of multifunctional block copoly(2-oxazoline)s for the synthesis of nanoparticles
(2021)
Post-polymerization modification provides an elegant way to introduce chemical functionalities onto macromolecules to produce tailor-made materials with superior properties. This concept was adapted to well-defined block copolymers of the poly(2-oxazoline) family and demonstrated the large potential of these macromolecules as universal toolkit for numerous applications. Triblock copolymers with separated water-soluble, alkyne- and alkene-containing segments were synthesized and orthogonally modified with various low-molecular weight functional molecules by copper(I)-catalyzed azide-alkyne cycloaddition (CuAAC) and thiol-ene (TE) click reactions, respectively. Representative toolkit polymers were used for the synthesis of gold, iron oxide and silica nanoparticles.
Frequency-domain electromagnetic (FDEM) data are commonly inverted to characterize subsurface geoelectrical properties using smoothness constraints in 1D inversion schemes assuming a layered medium.
Smoothness constraints are suitable for imaging gradual transitions of subsurface geoelectrical properties caused, for example, by varying sand, clay, or fluid content. However, such inversion approaches are limited in characterizing sharp interfaces. Alternative regularizations based on the minimum gradient support (MGS) stabilizers can, instead, be used to promote results with different levels of smoothness/sharpness selected by simply acting on the so-called focusing parameter.
The MGS regularization has been implemented for different kinds of geophysical data inversion strategies. However, concerning FDEM data, the MGS regularization has only been implemented for vertically constrained inversion (VCI) approaches but not for laterally constrained inversion (LCI) approaches.
We present a novel LCI approach for FDEM data using the MGS regularization for the vertical and lateral direction. Using synthetic and field data examples, we demonstrate that our approach can efficiently and automatically provide a set of model solutions characterized by different levels of sharpness and variable lateral consistencies.
In terms of data misfit, the obtained set of solutions contains equivalent models allowing us also to investigate the non-uniqueness of FDEM data inversion.
Thirteen N-butylpyridinium salts, including three monometallic [C4Py](2)[MCl4], nine bimetallic [C4Py](2)[(M1-xMxCl4)-M-a-Cl-b] and one trimetallic compound [C4Py](2)[(M1-y-zMyMz (c) Cl4)-M-a-M-b] (M=Co, Cu, Mn; x=0.25, 0.50 or 0.75 and y=z=0.33), were synthesized and their structure and thermal and electrochemical properties were studied. All compounds are ionic liquids (ILs) with melting points between 69 and 93 degrees C. X-ray diffraction proves that all ILs are isostructural. The conductivity at room temperature is between 10(-4) and 10(-8) S cm(-1). Some Cu-based ILs reach conductivities of 10(-2) S cm(-1), which is, however, probably due to IL dec. This correlates with the optical bandgap measurements indicating the formation of large bandgap semiconductors. At elevated temperatures approaching the melting points, the conductivities reach up to 1.47x10(-1) S cm(-1) at 70 degrees C. The electrochemical stability windows of the ILs are between 2.5 and 3.0 V.