Refine
Language
- English (15)
Is part of the Bibliography
- yes (15)
Keywords
- Kinetics (4)
- 4-nitrophenol (2)
- Adsorbent (2)
- Adsorption (2)
- Carica papaya seeds (2)
- E. coli (2)
- Kaolinite (2)
- Regeneration (2)
- Water (2)
- Water treatment (2)
Kinetics and time-dependent Langmuir modeling of 4-nitrophenol adsorption onto Mansonia sawdust
(2013)
Often time's adsorption of large molecules onto untreated lignocellulosic materials is viewed as a two stage process and has frequently been characterized only by kinetic models while the rate limiting step of adsorption is determined only at various stages of the adsorption process. In this study the kinetics and the contribution of diffusion processes to 4-nitrophenol adsorption onto untreated sawdust was examined and the overall rate limiting step evaluated.
The adsorption profile showed an initial rapid uptake of 4-nitrophenol which decreased and became almost constant after 5 min of contact. Analysis of the adsorption profile with the intraparticle diffusion equation and fractional 4-nitrophenol uptake with time showed that the profile can be divided into three different stages. The rate determining step of 4-nitrophenol adsorption was then evaluated based on the activation energies of each processes along with their activation parameters (Delta G*, Delta H* and Delta S*). The results revealed that external mass transfer was the overall rate limiting step with activation parameters E-a = 21.11, Delta H* = 23.75 and Delta S* = 144.97. Time dependent Langmuir modeling was carried out to optimize process parameters. (c) 2013 Taiwan Institute of Chemical Engineers. Published by Elsevier B.V. All rights reserved.
A polymer-clay based composite adsorbent was prepared from locally obtained kaolinite clay and polyvinyl alcohol. The composite adsorbent was used to remove lead (II) ions from aqueous solution in a fixed bed mode. The increase in bed height and initial metal ion concentration increased the adsorption capacity of lead (II) and the volume of aqueous solution treated at 50% breakthrough. However, the adsorption capacity was reduced by almost 16.5% with the simultaneous presence of Ca2+/Pb2+ and Na+/Pb2+ in the aqueous solution. Regeneration of the adsorbent with 0.1 M of HCl also reduced its adsorption capacity to 75.1%. Adsorption of lead (II) ions onto the polymer-clay composite adsorbent in the presence of Na+ and Ca2+ electrolyte increased the rate of mass transfer, probably due to competition between cationic species in solution for adsorption sites. Regeneration further increased the rate of mass transfer as a result of reduced adsorption sites after the regeneration process. The length of the mass transfer zone was found to increase with increasing bed height but did not change with increasing the initial metal ion concentration. The models of Yoon-Nelson, Thomas, and Clark were found to give good fit to adsorption data. On the other hand, Bohart-Adams model was found to be a poor predictor for the column operation. The polymer-clay composite adsorbent has a good potential for the removal of lead (II) ions from highly polluted aqueous solutions.
This study reports the sequestration of Cd(II) and Hg(II) using a new biosorbent. Nauclea diderrichii seed biomass. Experimental data obtained were fitted into kinetic and thermodynamic models. Experimental data fitted best into pseudo-second order kinetic model among others. Results obtained kinetically revealed that the biosorption of Cd(II) and Hg(II) using N. diderrichii seed biosorbent increased with increase in temperature. At the highest temperature, which was 333 K. the highest amount of metal biosorbed, q(e), for Cd(II) and Hg(II) obtained were 6.30 and 6.15 mg/g respectively. The biosorption of Cd(II) was kinetically faster than that of Hg(II), the highest initial biosorption rates for Cd(II) and Hg(II) were 56.19 and 4.39 mg/g min respectively. Thermodynamic parameters obtained by Erying equation from this study revealed that the biosorption process was spontaneous, feasible, endothermic with a decrease in the degree of chaos in the biosorption system. (C) 2012 Elsevier Ltd. All rights reserved.
This study is a first-hand report of the immobilization of Nauclea diderrichii seed waste biomass (ND) (an agro-waste) with eco-friendly mesoporous silica (MS) and graphene oxide-MS (GO+MS ) nanoparticles, producing two new hybrid materials namely: MND adsorbent for agro-waste modified with MS and GND adsorbent for agro-waste modified with GO+MS nanoparticles showed improved surface area, pore size and pore volume over those of the agro-waste. The abstractive potential of the new hybrid materials was explored for uptake of Cr(III) and Pb(II) ions. Analysis of experimental data from these new hybrid materials showed increased initial sorption rate of Cr(III) and Pb(II) ions uptake. The amounts of Cr(III) and Pb(II) ions adsorbed by MND and GND adsorbents were greater than those of ND. Modification of N. diderrichii seed waste significantly improved its rate of adsorption and diffusion coefficient for Cr(III) and Pb(II) more than its adsorption capacity. The rate of adsorption of the heavy metal ions was higher with GO+MS nanoparticles than for other adsorbents. Kinetic data were found to fit well the pseudo-second-order and the diffusion-chemisorption kinetic models suggesting that the adsorption of Cr(III) and Pb(II) onto these adsorbents is mainly through chemisorption mechanism. Analysis of kinetic data with the homogeneous particle diffusion kinetic model suggests that particle diffusion (diffusion of ions through the adsorbent) is the rate-limiting step for the adsorption process.
OPTIMIZATION OF THE BIOSORPTION OF Cr3+, Cd2+ AND Pb2+ USING A NEW BIOWASTE: Zea mays SEED CHAFF
(2016)
This study highlights the potential use of yellow Zea mays seed chaff (YZMSC) biomass as a biosorbent for the removal of Cr3+, Cd2+ and Pb2+ ions from aqueous solutions. Fourier transformed Infrared analysis of the biomass suggests that YZMSC biomass is basically composed of cellulose and methyl cellulose. The biosorption capacities, q(max), of YZMSC biomass for Cr3+, Cd2+ and Pb2+ are 14.68, 121.95 and 384.62 mg/g respectively. Biosorption equilibrium was achieved at 20, 30 and 60 min for Cr3+, Cd2+ and Pb2+ respectively. YZMSC biomass was found to have higher biosorption capacity and overall kinetic rate of uptake for Pb2+ than for Cd2+ and Cr3+. However, Cr3+ had better initial kinetic rate of uptake by the biomass than Pb2+ and Cd2+. The Freundlich equilibrium isotherm model was found to describe equilibrium data better than Langmuir model suggesting that biosorption of these metal ions could be on more than one active site on the surface of YZMSC biomass. Kinetic study predicted the pseudo-second kinetic model as being able to better describe kinetic data obtained than either modified pseudo-first order or Bangham kinetic models. Biosorption of Cr3+, Cd2+ and Pb2+ onto YZMSC biomass was endothermic in nature with large positive entropy values. Biosorption of these metal ions onto YZMSC biomass was observed to be feasible and spontaneous above 283 K. Optimization of biomass weight for the removal of these metal ions suggest that 384 kg, 129 kg and 144 kg of YZMSC biomass is required for the removal of 95% of Cr3+, Cd2+ and Pb2+ metal ions respectively from 100 mg/L of metal ions in 10 tonnes of aqueous solutions.
Toxic Cr(III) which poses environmental hazard to flora and fauna was efficiently abstracted by low-cost Nauclea diderrichii seed biomass (NDS) with good sequestral capacity for this metal was investigated in this study. The NDS surface analyses showed that it has a specific surface area of 5.36 m(2)/g and pHpzc of 4.90. Thermogravimetric analysis of NDS showed three consecutive weight losses from 50-200 degrees C (ca. 5%), 200-400 C (ca. 35%), >400 degrees C (ca. 10%), corresponding to external water molecules, structural water molecules and heat induced condensation reactions respectively. Differential thermogram of NDS presented a large endothermic peak between 20-510 degrees C suggesting bond breakage and dissociation with the ultimate release of small molecules. The experimental data showed kinetically fast biosorption with increased initial Cr(III) concentrations, indicating the role of external mass transfer mechanism as the rate controlling mechanism in this adsorption process. The Langmuir biosorption capacity of NDS was 483.81 mg/g. The use of the corrected Akaike Information Criterion tool for ranking equilibrium models suggested that the Freundlich model best described the experimental data, which is an indication of the heterogeneous nature of the active sites on the surface of NDS. N. diderrichii seed biomass is an easily sourced, cheap and environmental friendly biosorbent which will serve as a good and cost effective alternative to activated carbon for the treatment of polluted water and industrial effluents. (C) 2012 King Saud University. Production and hosting by Elsevier B.V. All rights reserved.
The competitive extraction of Cr(III) onto Nauclea diderrichii seed epicarp doped with MnO2 nanoparticles (MnO2 nano-bioextractant (MNB)) in a single and binary batch system was studied. For validity of experimental data, chi square test, root mean square error, sum of the square errors, hybrid fractional error function, Marquart’s percent standard deviation and standard absolute error were used. Among the kinetic models used, pseudo-second-order and Langmuir equations gave the best fits for the experimental data, with qe (mg g) for the uptake of Cr(III) in single metal system onto MNB, then Cr(III) with Cd(II), Pb(II), Hg(II), KCl and CaCl2 in binary metal systems onto MNB were 2.611, then 1.989, 1.016, 2.208, 1.249 and 1.868 from kinetic standpoint, respectively. The initial sorption rates, h (mg/g/min), and half lives, t1/2 (min), for the uptake of Cr(III) in single metal system onto MNB, then Cr(III) with Cd(II), Pb(II), Hg(II), KCl and CaCl2 in binary metal system onto MNB were 3.497, then 2.311, 2.274, 0.242, 2.956, 45.568 and 0.747, then 5.769, 1.766, 12.144, 1.762, and 2.415, respectively. Physicochemical surface analyses such as pH of point of zero charge, Brunauer–Emmett–Teller single point and multi-point techniques for surface area analyses, scanning electron microscopy and transmission electron microscopy were done on MNB and MnO2 nanoparticles in order to understand their surface microstructures. Desorption study showed that MNB can be recycled and used for future study. Hence, MNB showed good potential to remediate Cr(III) from wastewaters and polluted water.
A new sulfonated aniline-modified poly(vinyl alcohol)/K-feldspar (SAPK) composite was prepared. The cation-exchange capacity of the composite was found to be S times that of neat feldspar. The specific surface area and point of zero charge also changed significantly upon modification, from 15.6 +/- 0.1 m(2)/g and 2.20 (K-feldspar) to 73.6 +/- 0.3 m(2)/g and 1.91 (SAPK). Zn2+, Cd2+, and Pb2+ adsorption was found to be largely independent of pH, and the metal adsorption rate on SAPK was higher than that on neat feldspar. This particularly applies to the initial adsorption rates. The adsorption process involves both film and pore diffusion; film diffusion initially controls the adsorption. The Freundlich and Langmuir models were found to fit metal-ion adsorption on SAPK most accurately. Adsorption on neat feldspar was best fitted with a Langmuir model, indicating the formation of adsorbate monolayers. Both pure feldspar and SAPK showed better selectivity for Pb2+ than for Cd2+ or Zn2+.
A class of adsorbents currently receiving growing attention is the clay-polymer nanocomposite (CPN) adsorbents. CPNs effectively treat water by adsorption and flocculation of both inorganic and organic micropollutants from aqueous solutions. Some of these CPNs - when modified with biocides - also have the ability to efficiently remove microorganisms such as Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Candida albicans from water. CPNs are far more easily recovered from aqueous media than neat clay. They also exhibit far better treatment times than either polymer or clay adsorbents. They have higher adsorption capacity and better life cycles compared with clay alone. CPNs therefore show an excellent potential as highly efficient water and waste treatment agents.
This article reviews the various CPNs that have been prepared recently and used as adsorbents in the removal of micropollutants (inorganic, organic and biological) from aqueous solutions. A special focus is placed on CPNs that are not only interesting from an academic point of view but also effectively reduce the concentration of micropollutants in water to safe limits and also on new developments bordering on CPN use as water treatment agent that have not yet realized their full potential. (C) 2014 Elsevier B.V. All rights reserved.
Visible-Light-Mediated Photodynamic Water Disinfection @ Bimetallic-Doped Hybrid Clay Nanocomposites
(2019)
This study reports a new class of photocatalytic hybrid clay nanocomposites prepared from low-cost sources (kaolinite clay and Carica papaya seeds) doped with Zn and Cu salts via a solvothermal process. X-ray diffraction analysis suggests that Cu-doping and Cu/Zn-doping introduce new phases into the crystalline structure of Kaolinite clay, which is linked to the reduced band gap of kaolinite from typically between 4.9 and 8.2 eV to 2.69 eV for Cu-doped and 1.5 eV for Cu/Zn hybrid clay nanocomposites (Nisar, J.; Arhammar, C.; Jamstorp, E.; Ahuja, R. Phys. Rev. B 2011, 84, 075120). In the presence of solar light irradiation, Cu- and Cu/Zn-doped nanocomposites facilitate the electron hole pair separation. This promotes the generation of singlet oxygen which in turn improves the water disinfection efficiencies of these novel nanocomposite materials. The nanocomposite materials were further characterized using high-resolution scanning electron microscopy, fluorimetry, therrnogravimetric analysis, and Raman spectroscopy. The breakthrough times of the nanocomposites for a fixed bed mode of disinfection of water contaminated with 2.32 x 10(7) cfu/mL E. coli ATCC 25922 under solar light irradiation are 25 h for Zn-doped, 30 h for Cu-doped, and 35 h for Cu/Zn-doped nanocomposites. In the presence of multidrug and multimetal resistant strains of E. coli, the breakthrough time decreases significantly. Zn-only doped nanocomposites are not photocatalytically active. In the absence of light, the nanocomposites are still effective in decontaminating water, although less efficient than under solar light irradiation. Electrostatic interaction, metal toxicity, and release of singlet oxygen (only in the Cu-doped and Cu/Zn-doped nanocomposites) are the three disinfection mechanisms by which these nanocomposites disinfect water. A regrowth study indicates the absence of any living E. coli cells in treated water even after 4 days. These data and the long hydraulic times (under gravity) exhibited by these nanocomposites during photodisinfection of water indicate an unusually high potential of these nanocomposites as efficient, affordable, and sustainable point-of-use systems for the disinfection of water in developing countries.