Refine
Has Fulltext
- no (81)
Year of publication
Document Type
- Article (81) (remove)
Language
- English (81) (remove)
Is part of the Bibliography
- yes (81)
In this work, we report our investigations on the film-forming properties as well as the optical and electroluminescent characterisations of a series of lateral-substituted soluble oligo(phenylenevinylenes) of various conjugation length. Preliminary investigations show that these materials are potential candidates for use in organic light-emitting devices (OLEDs). Two types of OLEDs were fabricated: single layer (SL) and single heterostructure (SHS), with poly(p-phenylenevinylene) (PPV) as hole transporting layer. Our best results were obtained with single layer device emitting green light with a luminance of 0.18 cd m(-2) and 0.24 cd m(-2) at a driving voltage of 10 V. (c) 2004 Elsevier B.V. All rights reserved
The photoalignment ability of poly[methyl(phenyl)silylene] (PMPSi) films makes it possible to use them as hole- transporting substrates for the preparation of organic oriented films. A PMPSi layer prepared by spin coating was irradiated, after drying, with linearly polarized UV light. Then, water-soluble hydroxyaluminium phthalocyaninesulfonate [Al(OH)Pc(SO3Na)(1-2)] was deposited by casting. The cell ITO/PMPSi/AI(OH)Pc(SO3Na)(1-2)/Al showed non-linear current- voltage characteristics. For applied voltages higher than 10 V, polarized electroluminescence was observed. Its spectral characteristic consisted of two peaks with maxima at about 320 and 700 nm; their polarized anisotropies R-EL = Phi(parallel to) / Phi(perpendicular to) were ca. 15 and 0.5, respectively
Films of emeraldine base of polyaniline (PAni) doped by various transition metal salts have been prepared, and current-voltage characteristics of the indium-tin oxide (ITO)/PAni film/metal electrode heterostructures were investigated. It was found that the electrical characteristics of the heterostructures are greatly affected by the dopant used and the metal electrode used. Different dopants resulted in different current anomalies with asymmetric current-voltage characteristics. Depending on the dopant used, the exponential and power law of the current behavior can be distinguished. Depending on the metal electrode used, two different regimes of current passing have been found at low applied voltages, namely, a nearly ohmic regime for the indium electrode, and a diode regime for the aluminum electrode. The diode regime was found to accompany by a positive charge accumulation in the film near the film/metal interface, which creates a built-in potential in the film. The amount of positive charges accumulated at the interface and therefore the value of the built-in potential can be reversibly increased or reduced by successive runs of the applied voltage in the forward or reverse direction, respectively. (C) 2004 Elsevier B.V. All rights reserved
Conjugated polymers are organic semiconducting materials that can emit light. These polymers have the advantages of being light, cheap, and easy to process, and in addition the band gap can be tailored. We report the microfabrication of surface light emitting diodes (SLEDs) on silicon substrates in which the electrodes are underneath the organic electroluminescent layer. Patterned electrodes are separated by a 2500Å-thick insulating layer of silicon oxide or are interdigitated with a separation of 10 or 20 µm; the luminescent polymer is spin-coated or solvent cast on top of the electrodes. This fabrication method is completely compatible with conventional silicon processing because the polymer is deposited last and the light is emitted from the upper surface of the diodes. Despite the large spacing between electrodes, and despite the absence of an evaporated top contact, the voltages required for light emission were not much greater than those used in conventional sandwich-type structures
The surface structures of crystals based on aromatic oxadiazoles were investigated by AFM. The crystal structure for 2,5-di(p-tolyl)-1,3,4-oxadiazole (DTO) differs from that of 2,5-di (4-methoxycarbonyl-phenyl)-1,3,4- oxadiazole (DMPO). In DMPO all molecules show parallel orientation to the surface in such a way that the surface is formed as well as by the nitrogen atoms of the heterocyclic rings and the methyl groups of the ester substituents. By contrast, the oxadiazole molecules in DTO crystals are oriented perpendicular to the crystal surface. The experimental data are interpreted by molecular modelling. It is shown that there is a difference between molecular structure of the surface, as detected by AFM, and the bulk structure determined by X-ray diffraction.
New aromatic poly(1,3,4-oxadiazole)s were synthesized having excellent film forming properties due to their solubility in common organic solvents. The investigated new polyoxadiazoles can be used as emission material in single layer LED. The poly- oxadiazoles show an emission in the range of blue to yellow light. The external quantum efficiency as well as the turn-on voltage of the devices are influenced when blends of the polyoxadiazole with hole transport materials are used.
Poly(1,3,4-oxadiazole)s have been the focus of considerable interest with regard to the- production of high- performance materials, particularly owing to their high thermal stability in oxidative atmosphere and specific properties determined by the structure of 1,3,4-oxadiazole ring, which, from the spectral and electronic points of view, is similar to a p-phenylene structure.[1] Besides their excellent resistance to high temperature, polyoxadiazoles have many desirable characteristics, such as good hydrolytic stability, high glass transition temperatures, low dielectric constants, and tough mechanical properties. Some polyoxadiazoles have semiconductive properties, other structures can be electrochemically doped and thus made conductive, and other have liquid-crystalline properties, which make them very attractive for a wide range of high-performance applications. They exhibit excellent fiber- and film-forming capabilities, thus being considered for use as heat-resistant reinforcing fibers for advanced composite materials, highly resistant fabrics for the filtration of hot gases, special membranes for gas separation or reverse osmosis, precursors for highly oriented graphite fibers, films, and blocks to be used in the construction of electronic instruments based on X-rays, neutron beams, or a-particles, or in the construction of nuclear reactor walls. Since they were first reported in 1961,[2] a wide variety of polymers containing 1,3,4-oxadiazole rings have been synthesized, and their preparation, characterization, and physico-mechanical properties have been periodically reviewed .[3-8] This article will present a general overview of this class of polymers and will refer to the work carried out by different researchers in the last ten years with the emphasis on the potential uses of such polymers as advanced materials.