Refine
Has Fulltext
- yes (3) (remove)
Document Type
- Doctoral Thesis (3) (remove)
Language
- English (3)
Is part of the Bibliography
- yes (3) (remove)
Keywords
- additive Fertigung (3) (remove)
Institute
Additive Manufacturing (AM) in terms of laser powder-bed fusion (L-PBF) offers new prospects regarding the design of parts and enables therefore the production of lattice structures. These lattice structures shall be implemented in various industrial applications (e.g. gas turbines) for reasons of material savings or cooling channels. However, internal defects, residual stress, and structural deviations from the nominal geometry are unavoidable.
In this work, the structural integrity of lattice structures manufactured by means of L-PBF was non-destructively investigated on a multiscale approach.
A workflow for quantitative 3D powder analysis in terms of particle size, particle shape, particle porosity, inter-particle distance and packing density was established. Synchrotron computed tomography (CT) was used to correlate the packing density with the particle size and particle shape. It was also observed that at least about 50% of the powder porosity was released during production of the struts.
Struts are the component of lattice structures and were investigated by means of laboratory CT. The focus was on the influence of the build angle on part porosity and surface quality. The surface topography analysis was advanced by the quantitative characterisation of re-entrant surface features. This characterisation was compared with conventional surface parameters showing their complementary information, but also the need for AM specific surface parameters.
The mechanical behaviour of the lattice structure was investigated with in-situ CT under compression and successive digital volume correlation (DVC). The deformation was found to be knot-dominated, and therefore the lattice folds unit cell layer wise.
The residual stress was determined experimentally for the first time in such lattice structures. Neutron diffraction was used for the non-destructive 3D stress investigation. The principal stress directions and values were determined in dependence of the number of measured directions. While a significant uni-axial stress state was found in the strut, a more hydrostatic stress state was found in the knot. In both cases, strut and knot, seven directions were at least needed to find reliable principal stress directions.
Additive manufacturing (AM) processes enable the production of metal structures with exceptional design freedom, of which laser powder bed fusion (PBF-LB) is one of the most common. In this process, a laser melts a bed of loose feedstock powder particles layer-by-layer to build a structure with the desired geometry. During fabrication, the repeated melting and rapid, directional solidification create large temperature gradients that generate large thermal stress. This thermal stress can itself lead to cracking or delamination during fabrication. More often, large residual stresses remain in the final part as a footprint of the thermal stress. This residual stress can cause premature distortion or even failure of the part in service. Hence, knowledge of the residual stress field is critical for both process optimization and structural integrity.
Diffraction-based techniques allow the non-destructive characterization of the residual stress fields. However, such methods require a good knowledge of the material of interest, as certain assumptions must be made to accurately determine residual stress. First, the measured lattice plane spacings must be converted to lattice strains with the knowledge of a strain-free material state. Second, the measured lattice strains must be related to the macroscopic stress using Hooke's law, which requires knowledge of the stiffness of the material. Since most crystal structures exhibit anisotropic material behavior, the elastic behavior is specific to each lattice plane of the single crystal. Thus, the use of individual lattice planes in monochromatic diffraction residual stress analysis requires knowledge of the lattice plane-specific elastic properties. In addition, knowledge of the microstructure of the material is required for a reliable assessment of residual stress.
This work presents a toolbox for reliable diffraction-based residual stress analysis. This is presented for a nickel-based superalloy produced by PBF-LB. First, this work reviews the existing literature in the field of residual stress analysis of laser-based AM using diffraction-based techniques. Second, the elastic and plastic anisotropy of the nickel-based superalloy Inconel 718 produced by PBF-LB is studied using in situ energy dispersive synchrotron X-ray and neutron diffraction techniques. These experiments are complemented by ex situ material characterization techniques. These methods establish the relationship between the microstructure and texture of the material and its elastic and plastic anisotropy. Finally, surface, sub-surface, and bulk residual stress are determined using a texture-based approach. Uncertainties of different methods for obtaining stress-free reference values are discussed.
The tensile behavior in the as-built condition is shown to be controlled by texture and cellular sub-grain structure, while in the heat-treated condition the precipitation of strengthening phases and grain morphology dictate the behavior. In fact, the results of this thesis show that the diffraction elastic constants depend on the underlying microstructure, including texture and grain morphology. For columnar microstructures in both as-built and heat-treated conditions, the diffraction elastic constants are best described by the Reuss iso-stress model. Furthermore, the low accumulation of intergranular strains during deformation demonstrates the robustness of using the 311 reflection for the diffraction-based residual stress analysis with columnar textured microstructures. The differences between texture-based and quasi-isotropic approaches for the residual stress analysis are shown to be insignificant in the observed case. However, the analysis of the sub-surface residual stress distributions show, that different scanning strategies result in a change in the orientation of the residual stress tensor. Furthermore, the location of the critical sub-surface tensile residual stress is related to the surface roughness and the microstructure. Finally, recommendations are given for the diffraction-based determination and evaluation of residual stress in textured additively manufactured alloys.
Biomimicry is the art of mimicking nature to overcome a particular technical or scientific challenge. The approach studies how evolution has found solutions to the most complex problems in nature. This makes it a powerful method for science. In combination with the rapid development of manufacturing and information technologies into the digital age, structures and material that were before thought to be unrealizable can now be created with simple sketch and the touch of a button. This doctoral thesis had as its primary goal to investigate how digital tools, such as programming, modelling, 3D-Design tools and 3D-Printing, with the help from biomimicry, could lead to new analysis methods in science and new medical devices in medicine.
The Electrical Discharge Machining (EDM) process is applied commonly to deform or mold hard metals that are difficult to work using normal machinery. A workpiece submerged in an electrolyte is deformed while being in close vicinity to an electrode. When high voltage is put between the workpiece and the electrode it will cause sparks that create cavitations on the substrate which in turn removes material and is flushed away by the electrolyte. Usually, such surfaces are analysed based on roughness, in this work another method using a novel curvature analysis method is presented as an alternative. In addition, to better understand how the surface changes during process time of the EDM process, a digital impact model was created which created craters on ridges on an originally flat substrate. These substrates were then analysed using the curvature analysis method at different processing times of the modelling. It was found that a substrate reaches an equilibrium at around 10000 impacts. The proposed curvature analysis method has potential to be used in the design of new cell culture substrates for stem cell.
The Venus flytrap can shut its jaws at an amazing speed. The shutting mechanism may be interesting to use in science and is an example of a so-called mechanical bi-stable system – there are two stable states. In this work two truncated pyramid structures were modelled using a non-linear mechanical model called the Chained Beam Constraint Model (CBCM). The structure with a slope angle of 30 degrees is not bi-stable and the structure with a slope angle of 45 degrees is bi-stable. Developing this idea further by using PEVA, which has a shape-memory effect, the structure which is not bi-stable could be programmed to be bi-stable and then turned off again. This could be used as an energy storage system. Another species which has interesting mechanism is the tapeworm. Some species of this animal has a crown of hooks and suckers located on its side. The parasite commonly is found in mammals in the lower intestine and attaches to the walls by using its suckers. When the tapeworm has found a suitable spot, it ejects its hooks and permanently attaches to the wall. This function could be used in minimally invasive medicine to have better control of implants during the implantation process. By using the CBCM model and a 3D-printer capable of tuning how hard or soft a printed part is, a design strategy was developed to investigate how one could create a device that mimics the tapeworm. In the end a prototype was created which was able attach to a pork loin at an under pressure of 20 kPa and to ejects its hooks at an under pressure of 50 kPa or above.
These three projects is an exhibit of how digital tools and biomimicry can be used together to come up with applicable solutions in science and in medicine.