Refine
Has Fulltext
- no (29)
Document Type
- Article (29)
Language
- English (29)
Is part of the Bibliography
- yes (29)
Keywords
- electroactive polymer (2)
- permittivity enhancement (2)
- Actuator (1)
- Actuators (1)
- Capacitive sensor (1)
- Ceramics (1)
- Dielectric elastomer (1)
- Dielectric elastomer actuator (DEA) (1)
- Dielectric polymer (1)
- EAP (1)
Institute
Wave energy harvesting could be a substantial renewable energy source without impact on the global climate and ecology, yet practical attempts have struggled with the problems of wear and catastrophic failure. An innovative technology for ocean wave energy harvesting was recently proposed, based on the use of soft capacitors. This study presents a realistic theoretical and numerical model for the quantitative characterization of this harvesting method. Parameter regions with optimal behavior are found, and novel material descriptors are determined, which dramatically simplify analysis. The characteristics of currently available materials are evaluated, and found to merit a very conservative estimate of 10 years for raw material cost recovery.
Dielectric elastomer transducers consist of thin electrically insulating elastomeric membranes coated on both sides with compliant electrodes. They are a promising electromechanically active polymer technology that may be used for actuators, strain sensors, and electrical generators that harvest mechanical energy. The rapid development of this field calls for the first standards, collecting guidelines on how to assess and compare the performance of materials and devices. This paper addresses this need, presenting standardized methods for material characterisation, device testing and performance measurement. These proposed standards are intended to have a general scope and a broad applicability to different material types and device configurations. Nevertheless, they also intentionally exclude some aspects where knowledge and/or consensus in the literature were deemed to be insufficient. This is a sign of a young and vital field, whose research development is expected to benefit from this effort towards standardisation.
Analysis of the operating characteristics of a dielectric elastomer actuator (DEA) submount for the high-precision positioning of optical components in one dimension is presented. Precise alignment of a single-mode fiber is demonstrated and variation of the sensitivity of the submount motion by changing the bias voltage is confirmed. A comparison of the performance of the DEA submount with a piezoelectric alignment stage is made, which demonstrates that DEAs could present a very attractive, low-cost alternative to currently used manual technologies in overcoming the hurdle of expensive packaging of single-mode optical components.
We present accurate electromechanical measurements on a balanced push-pull dielectric elastomer actuator, demonstrating submicrometer accurate position control. An analytical model based on a simplified pure-shear dielectric elastomer film with prestretch is found to capture the voltage-displacement behavior, with reduced output due to the boundary conditions. Two complementary experiments show that actuation coefficients of 0.5-1 nm/V-2 are obtainable with the demonstrated device, enabling motion control with submicrometer accuracy in a voltage range below 200 V.
A new strategy for the synthesis of high permittivity polymer composites is demonstrated based on well-defined spatial distribution of ultralow amounts of conductive nanoparticles. The spatial distribution Was realized by immobilizing Cu nanoparticles within the pore system of Alia microspheres, preventing direct contact between individual Cu particles. Both Cu-loaded and unloaded silica microspheres were-then used as fillers in polymer composites prepared with thermoplastic SEBS rubber is the matrix. With a metallic Cu content of about 0.26 vol % In the compoilte, a relative increase of 94% In real permittivity was obtained. No Cu-induced relaxations were observed in the dielectric spectrum within the studied frequency range of 0.1 Hz to 1 MHz. When related to the amount of conductive nanoparticles, the obtained composites achieve the highest broad spectrum enhancement of permittivity ever reported for a polymer based composite.
A simple dip-coating technique was employed to manufacture coaxial actuators with multiple layers of alternating dielectric and conducting layers. A thin rubber string was coated with an electrode-insulator-electrode structure, giving rise to a thin, fiber-like actuator with coaxial geometry. The process was repeated to achieve a compact multilayer actuator with up to three coaxial dielectric layers. Mechanical and electromechanical characterization of the actuators is presented, showing actuation strains up to 8% and proper voltage-thickness scaling behavior. Also presented is a capacitance vs. extension plot, demonstrating that these structures can be used for compact and accurate capacitive strain sensing.
An approach for creating complex structures with embedded actuation in planar manufacturing steps is presented. Self-organization and energy minimization are central to this approach, illustrated with a model based on minimization of the hyperelastic free energy strain function of a stretched elastomer and the bending elastic energy of a plastic frame. A tulip-shaped gripper structure illustrates the technological potential of the approach. Advantages are simplicity of manufacture, complexity of final structures, and the ease with which any electroactive material can be exploited as means of actuation. (c) 2007 American Institute of Physics.
This Letter reports on new methods and a consistent model for voltage tunable optical transmission gratings. Elastomeric gratings were molded from holographically written surface relief gratings in an azobenzene sol-gel material. These were placed on top of a transparent electroactive elastomeric substrate. Two different electro-active substrate elastomers were employed, with a large range of prestretches. A novel finite-deformation theory was found to match the device response excellently, without fitting parameters. The results clearly show that the grating underwent pure-shear deformation, and more surprisingly, that the mechanical properties of the electro-active substrate did not affect device actuation. (C) 2011 Optical Society of America