Refine
Document Type
- Doctoral Thesis (12)
Is part of the Bibliography
- yes (12)
Keywords
- Polymerisation (3)
- polymerization (3)
- Antifouling (2)
- Polymere (2)
- 22-Hydroxydocosansäure (1)
- 22-hydroxydocosanoic acid (1)
- 9,10-Epoxy-18-hydroxyoctadecansäure (1)
- 9,10-epoxy-18-hydroxyoctadecanoic acid (1)
- Alkyd resin (1)
- Alkydharze (1)
Institute
- Institut für Chemie (11)
- Extern (1)
- Institut für Physik und Astronomie (1)
In den letzten Jahrzehnten fand auch in der Beschichtungsindustrie ein Umdenken hin zu umweltfreundlicheren Farben und Lacken statt. Allerdings basieren auch neue Lösungen meist nicht auf Biopolymeren und in einem noch geringeren Anteil auf wasserbasierten Beschichtungssystemen aus nachwachsenden Rohstoffen. Dies stellt den Anknüpfungspunkt dieser Arbeit dar, in der untersucht wurde, ob das Biopolymer Stärke das Potenzial zum wasserbasierten Filmbildner für Farben und Lacke besitzt. Dabei müssen angelehnt an etablierte synthetische Marktprodukte die folgenden Kriterien erfüllt werden: Die wässrige Dispersion muss mindestens einen 30%igen Feststoffgehalt haben, bei Raumtemperatur verarbeitet werden können und Viskositäten zwischen 10^2-10^3 mPa·s aufweisen. Die finale Beschichtung muss einen geschlossenen Film bilden und sehr gute Haftfestigkeiten zu einer spezifischen Oberfläche, in dieser Arbeit Glas, besitzen. Als Grundlage für die Modifizierung der Stärke wurde eine Kombination von molekularem Abbau und chemischer Funktionalisierung ausgewählt. Da nicht bekannt war, welchen Einfluss die Stärkeart, die gewählte Abbaureaktion als auch verschiedene Substituenten auf die Dispersionsherstellung und deren Eigenschaften sowie die Beschichtungseigenschaften ausüben könnten, wurden die strukturellen Parameter getrennt voneinander untersucht.
Das erste Themengebiet beinhaltete den oxidativen Abbau von Kartoffel- und Palerbsenstärke mittels des Hypochlorit-Abbaus (OCl-) und des ManOx-Abbaus (H2O2, KMnO4). Mit beiden Abbaureaktionen konnten vergleichbare gewichtsmittlere Molmassen (Mw) von 2·10^5-10^6 g/mol (GPC-MALS) hergestellt werden. Allerdings führten die gewählten Reaktionsbedingungen beim ManOx-Abbau zur Bildung von Gelpartikeln. Diese lagen im µm-Bereich (DLS und Kryo-REM-Messungen) und hatten zur Folge, dass die ManOx-Proben deutlich erhöhte Viskositäten (c: 7,5 %; 9-260 mPa·s) im Vergleich zu den OCl--Proben (4-10 mPa·s) bei scherverdünnendem Verhalten besaßen und die Eigenschaften von viskoelastischen Gelen (G‘ > G‘‘) zeigten. Des Weiteren wiesen sie reduzierte Heißwasserlöslichkeiten (95 °C, vorrangig: 70-99 %) auf. Der OCl--Abbau führte zu hydrophileren (Carboxylgruppengehalt bis zu 6,1 %; ManOx: bis zu 3,1 %), nach 95 °C-Behandlung vollständig wasserlöslichen abgebauten Stärken, die ein Newtonsches Fließverhalten mit Eigenschaften einer viskoelastischen Flüssigkeit (G‘‘ > G‘) hatten. Die OCl--Proben konnten im Vergleich zu den ManOx-Produkten (10-20 %) zu konzentrierteren Dispersionen (20-40 %) verarbeitet werden, die gleichzeitig die Einschränkung von anwendungsrelevanten Mw auf < 7·10^5 g/mol zuließen (Konzentration sollte > 30 % sein). Außerdem führten nur die OCl--Proben der Kartoffelstärke zu transparenten (alle anderen waren opak) geschlossenen Beschichtungsfilmen. Somit hebt sich die Kombination von OCl--Abbau und Kartoffelstärke mit Hinblick auf die Endanwendung ab.
Das zweite Themengebiet umfasste Untersuchungen zum Einfluss von Ester- und Hydroxyalkylether-Substituenten auf Basis einer industriell abgebauten Kartoffelstärke (Mw: 1,2·10^5 g/mol) vor allem auf die Dispersionsherstellung, die rheologischen Eigenschaften der Dispersionen und die Beschichtungseigenschaften in Kombination mit Glassubstraten. Dazu wurden Ester und Ether mit DS/MS-Werten von 0,07-0,91 synthetisiert. Die Derivate konnten zu wasserbasierten Dispersionen mit Konzentrationen von 30-45 % verarbeitet werden, wobei bei hydrophoberen Modifikaten ein Co-Lösemittel, Diethylenglycolmonobutylether (DEGBE), eingesetzt werden musste. Die Feststoffgehalte sanken dabei für beide Derivatklassen vor allem mit zunehmender Alkylkettenlänge. Die anwendungsrelevanten Viskositäten (323-1240 mPa·s) stiegen auf Grund von Wechselwirkungen tendenziell mit DS/MS und Alkylkettenlänge an. Hinsichtlich der Beschichtungseigenschaften erwiesen sich die Ester vergleichend zu den Ethern als die bevorzugte Substituentenklasse, da nur die Ester geschlossene, defektfreie und mehrheitlich transparente Beschichtungsfilme bildeten, die exzellente bis sehr gute Haftfestigkeiten (ISO Klasse: 0 und 1) auf Glas besaßen. Die Ether bildeten mehrheitlich brüchige Filme. Basierend auf der Kombination der Ergebnisse aus Lösemittelaustausch, den rheologischen Untersuchungen und zusätzlichen Oberflächenspannungsmessungen (30-61 mN/m) konnte geschlossen werden, dass wahrscheinlich fehlende oder schlechte Haftfestigkeiten vorrangig akkumuliertem Wasser in den Beschichtungsfilmen (visuell: trüb oder weiß) geschuldet sind, während die Brüchigkeit vermutlich auf Wechselwirkungen (H-Brücken Wechselwirkungen, hydrophobe Wechselwirkungen) zwischen den Polymeren zurückgeführt werden kann.
Insgesamt scheint die Kombination aus Kartoffelstärke basierend auf dem OCl--Abbau mit Mw < 7·10^5 g/mol und einem Estersubstituenten eine gute Wahl für wasserbasierte Dispersionen mit hohen Feststoffkonzentrationen (> 30 %), guter Filmbildung und exzellenten Haftungen auf Glas zu sein.
Die vorliegende Arbeit thematisiert die Synthese und Charakterisierung von neuen funktionalisierten ionischen Flüssigkeiten und deren Polymerisation. Die ionischen Flüssigkeiten wurden dabei sowohl mit polymerisierbaren Kationen als auch Anionen hergestellt. Zum einen wurden bei thermisch initiierten Polymerisationen Azobis(isobutyronitril) (AIBN) verwendet und zum anderen dienten bei photochemisch initiierten Polymerisationen Bis-4-(methoxybenzoyl)diethylgermanium (Ivocerin®) als Radikalstarter.
Mittels Gelpermeationschromatographie konnte das Homopolymer Polydimethylaminoethylmethacrylat untersucht werden, welches erst im Anschluss an die GPC-Messungen polymeranalog modifiziert wurde. Dabei wurden nach einer Quaternisierung und anschließender Anionenmetathese bei diesen Polymeren die Grenzviskositäten bestimmt und mit den Grenzviskositäten der direkt polymerisierten ionischen Flüssigkeiten verglichen. Bei der direkten Polymerisation von Poly(N-[2-(Methacryloyloxy)ethyl]-N-butyl-N,N-dimethyl-ammoniumbis(trifluormethylsulfonyl)imid) lag [η_Huggins] bei 100 mL/g und bei dem polymeranalog hergestellten Polymer betrug [η_Huggins] = 40 mL/g.
Die ionischen Flüssigkeiten mit polymerisierbaren funktionellen Gruppen wurden mittels Photo-DSC hinsichtlich der maximalen Polymerisationsgeschwindigkeit (Rpmax), der Zeit, in der dieses Maximum erreicht wurde, tmax, ihrer Glasüberganstemperatur (Tg) und des Umsatzes an Vinylprotonen untersucht. Bei diesen Messungen wurde zum einen der Einfluss der unterschiedlichen Alkylkettenlänge am Ammoniumion und der Einfluss von verschiedenen Anionen bei gleichbleibender Kationenstruktur analysiert. So polymerisierte das ethylsubstituierte Kation mit einer tmax von 21 Sekunden am langsamsten. Die maximale Polymerisationsgeschwindigkeit (Rpmax) betrug 3.3∙10-2 s-1. Die tmax Werte der übrigen alkylsubstituierten ionischen Flüssigkeiten mit einer polymerisierbaren funktionellen Gruppe hingegen lagen zwischen 10 und 15 Sekunden. Die Glasübergangstemperaturen der mittels photoinduzierter Polymerisation hergestellten Polymere lagen mit 44 bis 55 °C nahe beieinander. Alle Monomere zeigten einen hohen Umsatz der Vinylprotonen; er betrug zwischen 93 und 100%.
Mithilfe einer Bandanlage, ausgerüstet mit einer LED (λ = 395 nm), konnten Polymerfilme hergestellt werden. Der Umsatz an Doppelbindungsäquivalenten dieser Filme wurde anhand der 1H-NMR Spektroskopie bestimmt. Bei der dynamisch-mechanischen Analyse wurden die Polymerfilme mit einer konstanten Heizrate und Frequenz periodisch wechselnden Beanspruchungen ausgesetzt, um die Glasübergangstemperaturen zu bestimmen. Die niedrigste Tg mit 26 °C besaß das butylsubstituierte N-[2-(Methacryloyloxy)ethyl]-N-butyl-N,N-dimethyl-ammoniumbis(trifluormethylsulfonyl)imid, welches als Polymerfilm mit Ivocerin® als Initiator hergestellt wurde, wohingegen die höchste Tg bei dem gleichen Polymer, welches direkt durch freie radikalische Polymerisation der ionischen Flüssigkeit in Masse mit AIBN hergestellt wurde, 51 °C betrug. Zusätzlich wurden die Filme unter dem Aspekt der Topographie mit einem Rasterkraftmikroskop untersucht, welches eine Domänenstruktur des Polymers N-[2-(methacryloyloxy)ethyl]-N-butyl-N,N-dimethyl-ammonium tris(pentafluorethyl)trifluorphosphat offenbarte.
The present work focuses on minimising the usage of toxic chemicals by integration of the biobased monomers, derived from fatty acid esters, to photopolymerization processes, which are known to be nature friendly. Internal double bond present in the oleic acid was converted to more reactive (meth)acrylate or epoxy group. Biobased starting materials, functionalized by different pendant groups, were used for photopolymerizing formulations to design of new polymeric structures by using ultraviolet light emitting diode (UV-LED) (395 nm) via free radical polymerization or cationic polymerization.
New (meth)acrylates (2,3 and 4) consisting of two isomers, methyl 9-((meth)acryloyloxy)-10-hydroxyoctadecanoate / methyl 9-hydroxy-10-((meth)acryloyloxy)octadecanoate (2 and 3) and methyl 9-(1H-imidazol-1-yl)-10-(methacryloyloxy)octadecanoate / methyl 9-(methacryloyloxy)-10-(1H-imidazol-1-yl)octadecanoate (4), modified from oleic acid mix, and ionic liquid monomers (1a and 1b) bearing long alkyl chain were polymerized photochemically. New (meth)acrylates are based on vegetable oil, and ionic liquids (ILs) have nonvolatile behaviour. Therefore, both monomer types have green approach. Photoinitiated polymerization of new (meth)acrylates and ionic liquids was investigated in the presence of ethyl (2,4,6-trimethylbenzoyl) phenylphosphinate (Irgacure® TPO−L) or di(4-methoxybenzoyl)diethylgermane (Ivocerin®) as photoinitiator (PI). Additionally, the results were discussed in comparison with those obtained from commercial 1,6-hexanediol di(meth)acrylate (5 and 6) for deeper investigation of biobased monomer’s potential to substitute petroleum derived materials with renewable resources for possible coating applications. Kinetic study shows that methyl 9-(1H-imidazol-1-yl)-10-(methacryloyloxy)octadecanoate / methyl 9-(methacryloyloxy)-10-(1H-imidazol-1-yl)octadecanoate (4) and ionic liquids (1a and 1b) have quantitative conversion after irradiation process which is important for practical applications. On the other hand, heat generation occurs in a longer time during the polymerization of biobased systems or ILs.
The poly(meth)acrylates modified from (meth)acrylated fatty acid methyl ester monomers generally show a low glass transition temperature because of the presence of long aliphatic chain in the polymer structure. However, poly(meth)acrylates containing aromatic group have higher glass transition temperature. Therefore, new 4-(4-methacryloyloxyphenyl)-butan-2-one (7) was synthesized which can be a promising candidate for the green techniques, such as light induced polymerization. Photokinetic investigation of the new monomer, 4-(4-methacryloyloxyphenyl)-butan-2-one (7), was discussed using Irgacure® TPO−L or Ivocerin® as photoinitiator. The reactivity of that monomer was compared to commercial 2-phenoxyethyl methacrylate (8) and phenyl methacrylate (9) basis of the differences on monomer structures. The photopolymer of 4-(4-methacryloyloxyphenyl)-butan-2-one (7) might be an interesting candidate for the coating application with the properties of quantitative conversion and high molecular weight. It also shows higher glass transition temperature.
In addition to the linear systems based on renewable materials, new crosslinked polymers were also designed in this thesis. Therefore, isomer mixture consisting of ethane-1,2-diyl bis(9-methacryloyloxy-10-hydroxy octadecanoate), ethane-1,2-diyl 9-hydroxy-10-methacryloyloxy-9’-methacryloyloxy10’-hydroxy octadecanoate and ethane-1,2-diyl bis(9-hydroxy-10-methacryloyloxy octadecanoate) (10) was synthesized by derivation of the oleic acid which has not been previously described in the literature. Crosslinked material based on this biobased monomer was produced by photoinitiated free radical polymerization using Irgacure® TPO−L or Ivocerin® as photoinitiator. Furthermore, material properties were diversified by copolymerization of 10 with 4-(4-methacryloyloxyphenyl)-butan-2-one (7) or methyl 9-(1H-imidazol-1-yl)-10-(methacryloyloxy)octadecanoate / methyl 9-(methacryloyloxy)-10-(1H-imidazol-1-yl)octadecanoate (4). In addition to this, influence of comonomer with different chemical structure on the network system was investigated by analysis of thermo-mechanical properties, crosslink density and molecular weight between two crosslink junctions. An increase in the glass transition temperature caused by copolymerization of biobased monomer 10 with the excess amount of 4-(4-methacryloyloxyphenyl)-butan-2-one (7) was confirmed by both techniques, differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). On the other hand, crosslink density decreased as a result of copolymerization reactions due to the reduction in the mean functionality of the system. Furthermore, surface characterization has been tested by contact angle measurements using solvents with different polarity.
This work also contributes to the limited data reported about cationic photopolymerization of the epoxidized vegetable oils in the literature in contrast to the widely investigation of thermal curing of the biorenewable epoxy monomers. In addition to the 9,10-epoxystearic acid methyl ester (11), a new monomer of bis-(9,10-epoxystearic acid) 1,2-ethanediyl ester (12) has been synthesized from oleic acid. These two biobased epoxies have been polymerized via cationic photoinitiated polymerization in the presence of bis(t-butyl)-iodonium-tetrakis(perfluoro-t-butoxy)aluminate ([Al(O-t-C4F9)4]-) and isopropylthioxanthone (ITX) as photinitiating system. Polymerization kinetic of 9,10-epoxystearic acid methyl ester (11) and bis-(9,10-epoxystearic acid) 1,2-ethanediyl ester (12) was investigated and compared with the kinetic of commercial monomers being 3,4-epoxycyclohexylmethyl-3’,4’-epoxycyclohexane carboxylate (13), 1,4-butanediol diglycidyl ether (14), and diglycidylether of bisphenol-A (15). Both biobased epoxies (11 and 12) showed higher conversion than cycloaliphatic epoxy (13), and lower reactivity than 1,4-butanediol diglycidyl ether (14). Additional network systems were designed by copolymerization of bis-(9,10-epoxystearic acid) 1,2-ethanediyl ester (12) and diglycidylether of bisphenol-A (15) in different molar ratios (1:1; 1:5; 1:9). It addresses that, final conversion is dependent on polymerization rate as well as physical processes such as vitrification during polymerization. Moreover, low glass transition temperature of homopolymer derived from bis-(9,10-epoxystearic acid) 1,2-ethanediyl ester (12) was successfully increased by copolymerization with diglycidylether bisphenol-A (15). On the other hand, the surface produced from bis-(9,10-epoxystearic acid) 1,2-ethanediyl ester (12) shows hydrophobic character. Higher concentration of biobased diepoxy (12) in the copolymerizing mixture decreases surface free energy. Network systems were also investigated according to the rubber elasticity theory. Crosslinked polymer derived from the mixture of bis-(9,10-epoxystearic acid) 1,2-ethanediyl ester (12) and diglycidylether of bisphenol-A (15) (molar ratio=1:5) exhibits almost ideal polymer network.
Bio-sourced adsorbing poly(2-oxazoline)s mimicking mussel glue proteins for antifouling applications
(2022)
Nature developed countless systems for many applications. In maritime environments, several organisms established extra-ordinary mechanisms to attach to surfaces. Over the past years, the scientific interest to employ those mechanisms for coatings and long-lasting adhering materials gained significant attention.
This work describes the synthesis of bio-inspired adsorbing copoly(2-oxazoline)s for surface coatings with protein repelling effects, mimicking mussel glue proteins. From a set of methoxy substituted phenyl, benzyl, and cinnamyl acids, 2-oxazoline monomers were synthesized. All synthesized 2-oxazolines were analyzed by FT-IR spectroscopy, NMR spectroscopy, and EI mass spectrometry. With those newly synthesized 2-oxazoline monomers and 2-ethyl-2-oxazoline, kinetic studies concerning homo- and copolymerization in a microwave reactor were conducted. The success of the polymerization reactions was demonstrated by FT-IR spectroscopy, NMR spectroscopy, MALDI-TOF mass spectrometry, and size exclusion chromatography (SEC). The copolymerization of 2-ethyl-2-oxazoline with a selection of methoxy-substituted 2-oxazolines resulted in water-soluble copolymers. To release the adsorbing catechol and cationic units, the copoly(2-oxazoline)s were modified. The catechol units were (partially) released by a methyl aryl ether cleavage reaction. A subsequent partial acidic hydrolysis of the ethyl unit resulted in mussel glue protein-inspired catechol and cation-containing copolymers. The modified copolymers were analyzed by NMR spectroscopy, UV-VIS spectroscopy, and SEC. The catechol- and cation-containing copolymers and their precursors were examined by a Quartz Crystal Microbalance with Dissipation (QCM-D), so study the adsorption performance on gold, borosilicate, iron, and polystyrene surfaces. An exemplary study revealed that a catechol and cation-containing copoly(2-oxazoline)-coated gold surface exhibits strong protein repelling properties.
Die herausragenden mechanischen Eigenschaften natürlicher anorganisch-organischer Kompositmaterialien wie Knochen oder Muschelschalen entspringen ihrer hierarchischen Struktur, die von der nano- bis hinauf zur makroskopischen Ebene reicht, und einer kontrollierten Verbindung entlang der Grenzflächen der anorganischen und organischen Komponenten.
Ausgehend von diesen Schlüsselprinzipien des biologischen Materialdesigns wurden in dieser Arbeit zwei Konzepte für die bioinspirierte Strukturbildung von Kompositen untersucht, die auf dem Verkleben von Nano- oder Mesokristallen mit funktionalisierten Poly(2-oxazolin)-Blockcopolymeren beruhen sowie deren Potenzial zur Herstellung bioinspirierter selbstorganisierter hierarchischer anorganisch-organischer Verbundstrukturen ohne äußere Kräfte beleuchtet. Die Konzepte unterschieden sich in den verwendeten anorganischen Partikeln und in der Art der Strukturbildung.
Über einen modularen Ansatz aus Polymersynthese und polymeranaloger Thiol-En-Funktionalisierung wurde erfolgreich eine Bibliothek von Poly(2-oxazolin)en mit unterschiedlichen Funktionalitäten erstellt. Die Blockcopolymere bestehen aus einem kurzen partikelaffinen "Klebeblock", der aus Thiol-En-funktionalisiertem Poly(2-(3-butenyl)-2-oxazolin) besteht, und einem langen wasserlöslichen, strukturbildenden Block, der aus thermoresponsivem und kristallisierbarem Poly(2-isopropyl-2-oxazolin) besteht und hierarchische Morphologien ausbildet. Verschiedene analytische Untersuchungen wie Turbidimetrie, DLS, DSC, SEM oder XRD machten das thermoresponsive bzw. das Kristallisationsverhalten der Blockcopolymere in Abhängigkeit vom eingeführten Klebeblock zugänglich. Es zeigte sich, dass diese Polymere ein komplexes temperatur- und pH-abhängiges Trübungsverhalten aufweisen. Hinsichtlich der Kristallisation änderte der Klebeblock nicht die nanoskopische Kristallstruktur; er beeinflusste jedoch die Kristallisationszeit, den Kristallisationsgrad und die hierarchische Morphologie. Dieses Ergebnis wurde auf das unterschiedliche Aggregationsverhalten der Polymere in Wasser zurückgeführt.
Für die Herstellung von Kompositen nutzte Konzept 1 mikrometergroße Kupferoxalat-Mesokristalle, die eine innere Nanostruktur aufweisen. Die Strukturbildung über den anorganischen Teil wurde durch das Verkleben und Anordnen dieser Partikel erstrebt. Konzept 1 ermöglichte homogene freistehende stabile Kompositfilme mit einem hohen anorganischen Anteil. Die Partikel-Polymer-Kombination vereinte jedoch ungünstige Eigenschaften in sich, d. h. ihre Längenskalen waren zu unterschiedlich, was die Selbstassemblierung der Partikel verhinderte. Aufgrund des geringen Aspektverhältnisses von Kupferoxalat blieb auch die gegenseitige Ausrichtung durch äußere Kräfte erfolglos. Im Ergebnis eignet sich das Kupferoxalat-Poly(2-oxazolin)-Modellsystem nicht für die Herstellung hierarchischer Kompositstrukturen.
Im Gegensatz dazu verwendet Konzept 2 scheibenförmige Laponit®-Nanopartikel und kristallisierbare Blockcopolymere zur Strukturbildung über die organische Komponente durch polymervermittelte Selbstassemblierung. Komplementäre Analysemethoden (Zeta-Potenzial, DLS, SEM, XRD, DSC, TEM) zeigten sowohl eine kontrollierte Wechselwirkung zwischen den Komponenten in wässriger Umgebung als auch eine kontrollierte Strukturbildung, die in selbstassemblierten Nanokompositen resultiert, deren Struktur sich über mehrere Längenskalen erstreckt. Es wurde gezeigt, dass die negativ geladenen Klebeblöcke spezifisch und selektiv an den positiv geladenen Rändern der Laponit®-Partikel binden und so Polymer-Laponit®-Nanohybridpartikel entstehen, die als Grundbausteine für die Kompositbildung dienen. Die Hybridpartikel sind bei Raumtemperatur elektrosterisch stabilisiert - sterisch durch ihre langen, mit Wasser wechselwirkenden Poly(2-isopropyl-2-oxazolin)-Blöcke und elektrostatisch über die negativ geladenen Laponit®-Flächen. Im Ergebnis ließ sich Konzept 2 und damit die Strukturbildung über die organische Komponente erfolgreich umsetzten. Das Laponit®-Poly(2-oxazolin)-Modellsystem eröffnete den Weg zu selbstassemblierten geschichteten quasi-hierarchischen Nanokompositstrukturen mit hohem anorganischen Anteil. Abhängig von der frei verfügbaren Polymerkonzentration bei der Kompositbildung entstanden zwei unterschiedliche Komposit-Typen. Darüber hinaus entwarf die Arbeit einen Erklärungsansatz für den polymervermittelten Bildungsprozess der Komposit-Strukturen.
Insgesamt legt diese Arbeit Struktur-Prozess-Eigenschafts-Beziehungen offen, um selbstassemblierte bioinspirierte Kompositstrukturen zu bilden und liefert neue Einsichten zu einer geeigneten Kombination an Komponenten und Herstellungsbedingungen, die eine kontrollierte selbstassemblierte Strukturbildung mithilfe funktionalisierter Poly(2-oxazolin)-Blockcopolymere erlauben.
Die vorliegende Arbeit behandelt die Synthese und Charakterisierung von funktionalisierten Alkydharzen und die photoinduzierte Polymerisation dieser unter Einsatz einer Quecksilberdampflampe oder einer UV LED mit unterschiedlicher Lichtintensität. Der Fokus dieser Arbeit bestand in der gezielten Substitution der internalen Doppelbindungen der Fettsäureester durch reaktivere Gruppen, wie Acrylate oder Methacrylate, welche für Alkydharze in dieser Form so in der Literatur nicht beschrieben sind. Untersuchungen des Polymerisationsverhaltens dieser funktionalisierten Harze wurden mit der Photo DSC durchgeführt, wobei Bis – (4 – methoxybenzoyl) diethylgermanium als Photoinitiator diente. Die Ergebnisse haben gezeigt, dass die Harze radikalisch polymerisiert werden können und eine geringere Abhängigkeit von der Umgebungsatmosphäre (Luftsauerstoff bzw. Stickstoff) vorliegt. Dies ist so in der Literatur für funktionalisierte Alkydharze nicht bekannt. Abmischungen von unterschiedlichen Monomeren und funktionalisierten Harzen bewirkten eine Steigerung der Viskosität sowie eine Verringerung der Sauerstoffinhibierung im Zuge der photoinduzierten Polymerisation unter Luftsauerstoff für die Quecksilberdampflampe und der UV LED.
Zur Untersuchung der sauerstoffinhibierenden Wirkung der Harze sind Synthesen unterschiedlicher, funktionalisierter Ölsäuremethylester als Modellsubstanzen durchgeführt worden. Ein verbessertes Polymerisationsverhalten und eine geringe Abhängigkeit von der Umgebungsatmosphäre konnte für die Modelle nachgewiesen werden. Zur Aufklärung des verbesserten Polymerisationsverhaltens sind gezielt Substituenten (Imidazol, Brom, Alkohol, Acetat) in den funktionalisierten Ölsäuremethylester eingebaut worden, um den Einfluss dieser aufzuzeigen. Im Rahmen dieser Synthesen sind neuartige Strukturen synthetisiert worden, welche so in der Literatur nicht beschrieben sind. Die Gegenüberstellung der Polymerisationszeit, der Umsatz der (Meth-)Acrylatgruppen sowie die Zeit zum Erreichen der maximalen Polymerisationsgeschwindigkeit unter Verwendung von unterschiedlichen UV Lichtquellen hat einen Einfluss der Substituenten auf das Polymerisationsverhalten gezeigt.
The remarkable antifouling properties of zwitterionic polymers in controlled environments are often counteracted by their delicate mechanical stability. In order to improve the mechanical stabilities of zwitterionic hydrogels, the effect of increased crosslinker densities was thus explored. In a first approach, terpolymers of zwitterionic monomer 3-[N -2(methacryloyloxy)ethyl-N,N-dimethyl]ammonio propane-1-sulfonate (SPE), hydrophobic monomer butyl methacrylate (BMA), and photo-crosslinker 2-(4-benzoylphenoxy)ethyl methacrylate (BPEMA) were synthesized. Thin hydrogel coatings of the copolymers were then produced and photo-crosslinked. Studies of the swollen hydrogel films showed that not only the mechanical stability but also, unexpectedly, the antifouling properties were improved by the presence of hydrophobic BMA units in the terpolymers.
Based on the positive results shown by the amphiphilic terpolymers and in order to further test the impact that hydrophobicity has on both the antifouling properties of zwitterionic hydrogels and on their mechanical stability, a new amphiphilic zwitterionic methacrylic monomer, 3-((2-(methacryloyloxy)hexyl)dimethylammonio)propane-1-sulfonate (M1), was synthesized in good yields in a multistep synthesis. Homopolymers of M1 were obtained by free-radical polymerization. Similarly, terpolymers of M1, zwitterionic monomer SPE, and photo-crosslinker BPEMA were synthesized by free-radical copolymerization and thoroughly characterized, including its solubilities in selected solvents.
Also, a new family of vinyl amide zwitterionic monomomers, namely 3-(dimethyl(2-(N -vinylacetamido)ethyl)ammonio)propane-1-sulfonate (M2), 4-(dimethyl(2-(N-vinylacetamido)ethyl)ammonio)butane-1-sulfonate (M3), and 3-(dimethyl(2-(N-vinylacetamido)ethyl)ammonio)propyl sulfate (M4), together with the new photo-crosslinker 4-benzoyl-N-vinylbenzamide (M5) that is well-suited for copolymerization with vinylamides, are introduced within the scope of the present work. The monomers are synthesized with good yields developing a multistep synthesis. Homopolymers of the new vinyl amide zwitterionic monomers are obtained by free-radical polymerization and thoroughly characterized. From the solubility tests, it is remarkable that the homopolymers produced are fully soluble in water, evidence of their high hydrophilicity. Copolymerization of the vinyl amide zwitterionic monomers, M2, M3, and M4 with the vinyl amide photo-crosslinker M5 proved to require very specific polymerization conditions. Nevertheless, copolymers were successfully obtained by free-radical copolymerization under appropriate conditions.
Moreover, in an attempt to mitigate the intrinsic hydrophobicity introduced in the copolymers by the photo-crosslinkers, and based on the proven affinity of quaternized diallylamines to copolymerize with vinyl amides, a new quaternized diallylamine sulfobetaine photo-crosslinker 3-(diallyl(2-(4-benzoylphenoxy)ethyl)ammonio)propane-1-sulfonate (M6) is synthesized. However, despite a priori promising copolymerization suitability, copolymerization with the vinyl amide zwitterionic monomers could not be achieved.
Vom Monomer zum Glykopolymer
(2019)
Glykopolymere sind synthetische und natürlich vorkommende Polymere, die eine Glykaneinheit in der Seitenkette des Polymers tragen. Glykane sind durch die Glykan-Protein-Wechselwirkung verantwortlich für viele biologische Prozesse. Die Beteiligung der Glykanen in diesen biologischen Prozessen ermöglicht das Imitieren und Analysieren der Wechselwirkungen durch geeignete Modellverbindungen, z.B. der Glykopolymere. Dieses System der Glykan-Protein-Wechselwirkung soll durch die Glykopolymere untersucht und studiert werden, um die spezifische und selektive Bindung der Proteine an die Glykopolymere nachzuweisen. Die Proteine, die in der Lage sind, Kohlenhydratstrukturen selektiv zu binden, werden Lektine genannt.
In dieser Dissertationsarbeit wurden verschiedene Glykopolymere synthetisiert. Dabei sollte auf einen effizienten und kostengünstigen Syntheseweg geachtet werden.
Verschiedene Glykopolymere wurden durch funktionalisierte Monomere mit verschiedenen Zuckern, wie z.B. Mannose, Laktose, Galaktose oder N-Acetyl-Glukosamin als funktionelle Gruppe, hergestellt. Aus diesen funktionalisierten Glykomonomeren wurden über ATRP und RAFT-Polymerisation Glykopolymere synthetisiert.
Die erhaltenen Glykopolymere wurden in Diblockcopolymeren als hydrophiler Block angewendet und die Selbstassemblierung in wässriger Lösung untersucht. Die Polymere formten in wässriger Lösung Mizellen, bei denen der Zuckerblock an der Oberfläche der Mizellen sitzt. Die Mizellen wurden mit einem hydrophoben Fluoreszenzfarbstoff beladen, wodurch die CMC der Mizellenbildung bestimmt werden konnte.
Außerdem wurden die Glykopolymere als Oberflächenbeschichtung über „Grafting from“ mit SI-ATRP oder über „Grafting to“ auf verschiedene Oberflächen gebunden. Durch die glykopolymerbschichteten Oberflächen konnte die Glykan Protein Wechselwirkung über spektroskopische Messmethoden, wie SPR- und Mikroring Resonatoren untersucht werden. Hierbei wurde die spezifische und selektive Bindung der Lektine an die Glykopolymere nachgewiesen und die Bindungsstärke untersucht.
Die synthetisierten Glykopolymere könnten durch Austausch der Glykaneinheit für andere Lektine adressierbar werden und damit ein weites Feld an anderen Proteinen erschließen. Die bioverträglichen Glykopolymere wären alternativen für den Einsatz in biologischen Prozessen als Transporter von Medikamenten oder Farbstoffe in den Körper. Außerdem könnten die funktionalisierten Oberflächen in der Diagnostik zum Erkennen von Lektinen eingesetzt werden. Die Glykane, die keine selektive und spezifische Bindung zu Proteinen eingehen, könnten als antiadsorptive Oberflächenbeschichtung z.B. in der Zellbiologie eingesetzt werden.