TY - THES A1 - Schattauer, Sylvia T1 - Hybride Dünnschicht-Solarzellen aus mesoporösem Titandioxid und konjugierten Polymeren T1 - Hybrid thin solar cells comprising mesoporous titanium dioxide and conjugated polymers N2 - Das Ziel dieser Arbeit ist die Untersuchung der aktiven Komponenten und ihrer Wechselwirkungen in teilorganischen Hybrid-Solarzellen. Diese bestehen aus einer dünnen Titandioxidschicht, kombiniert mit einer dünnen Polymerschicht. Die Effizienz der Hybrid-Solarzellen wird durch die Lichtabsorption im Polymer, die Dissoziation der gebildeten Exzitonen an der aktiven Grenzfläche zwischen TiO2 und Polymer, sowie durch Generation und Extraktion freier Ladungsträger bestimmt. Zur Optimierung der Solarzellen wurden grundlegende physikalische Wechselwirkungen zwischen den verwendeten Materialen sowie der Einfluss verschiedener Herstellungsparameter untersucht. Unter anderem wurden Fragen zum optimalen Materialeinsatz und Präparationsbedingungen beantwortet sowie grundlegende Einflüsse wie Schichtmorphologie und Polymerinfiltration näher betrachtet. Zunächst wurde aus unterschiedlich hergestelltem Titandioxid (Akzeptor-Schicht) eine Auswahl für den Einsatz in Hybrid-Solarzellen getroffen. Kriterium war hierbei die unterschiedliche Morphologie aufgrund der Oberflächenbeschaffenheit, der Film-Struktur, der Kristallinität und die daraus resultierenden Solarzelleneigenschaften. Für die anschließenden Untersuchungen wurden mesoporöse TiO2–Filme aus einer neuen Nanopartikel-Synthese, welche es erlaubt, kristalline Partikel schon während der Synthese herzustellen, als Elektronenakzeptor und konjugierte Polymere auf Poly(p-Phenylen-Vinylen) (PPV)- bzw. Thiophenbasis als Donatormaterial verwendet. Bei der thermischen Behandlung der TiO2-Schichten erfolgt eine temperaturabhängige Änderung der Morphologie, jedoch nicht der Kristallstruktur. Die Auswirkungen auf die Solarzelleneigenschaften wurden dokumentiert und diskutiert. Um die Vorteile der Nanopartikel-Synthese, die Bildung kristalliner TiO2-Partikel bei tiefen Temperaturen, nutzen zu können, wurden erste Versuche zur UV-Vernetzung durchgeführt. Neben der Beschaffenheit der Oxidschicht wurde auch der Einfluss der Polymermorphologie, bedingt durch Lösungsmittelvariation und Tempertemperatur, untersucht. Hierbei konnte gezeigt werden, dass u.a. die Viskosität der Polymerlösung die Infiltration in die TiO2-Schicht und dadurch die Effizienz der Solarzelle beeinflusst. Ein weiterer Ansatz zur Erhöhung der Effizienz ist die Entwicklung neuer lochleitender Polymere, welche möglichst über einen weiten spektralen Bereich Licht absorbieren und an die Bandlücke des TiO2 angepasst sind. Hierzu wurden einige neuartige Konzepte, z.B. die Kombination von Thiophen- und Phenyl-Einheiten näher untersucht. Auch wurde die Sensibilisierung der Titandioxidschicht in Anlehnung an die höheren Effizienzen der Farbstoffzellen in Betracht gezogen. Zusammenfassend konnten im Rahmen dieser Arbeit wichtige Einflussparameter auf die Funktion hybrider Solarzellen identifiziert und z.T. näher diskutiert werden. Für einige limitierende Faktoren wurden Konzepte zur Verbesserung bzw. Vermeidung vorgestellt. N2 - The main objective of this thesis is to study the active components and their interactions in so called organic hybrid solar cells. These consist of a thin inorganic titanium dioxide layer, combined with a polymer layer. In general, the efficiency of these hybrid solar cells is determined by the light absorption in the donor polymer, the dissociation of excitons at the heterojunction between TiO2 and polymer, as well as the generation and extraction of free charge carriers. To optimize the solar cells, the physical interactions between the materials are modified and the influences of various preparation parameters are systematically investigated. Among others, important findings regarding the optimal use of materials and preparation conditions as well as detailed investigations of fundamental factors such as film morphology and polymer infiltration are presented in more detail. First, a variety of titanium dioxide layer were produced, from which a selection for use in hybrid solar cells was made. The obtained films show differences in surface structure, film morphology and crystallinity, depending on the way how the TiO2 layer has been prepared. All these properties of the TiO2 films may strongly affect the performance of the hybrid solar cells, by influencing e.g. the exciton diffusion length, the efficiency of exciton dissociation at the hybrid interface, and the carrier transport properties. Detailed investigations were made for mesoporous TiO2 layer following a new nanoparticle synthesis route, which allows to produce crystalline particles during the synthesis. As donor component, conjugated polymers, either derivatives of cyclohexylamino-poly(p-phenylene vinylene) (PPV) or a thiophene are used. The preparation routine also includes a thermal treatment of the TiO2 layers, revealing a temperature-dependent change in morphology, but not of the crystal structure. The effects on the solar cell properties have been documented and discussed. To take advantage of the nanoparticle synthesis, the formation of crystalline TiO2 particles by UV crosslinking and first solar cell measurements are presented. In addition to the nature of the TiO2 layer, the influence of polymer morphology is investigated. Different morphologies are realized by solvent variation and thermal annealing. It is shown that, among other factors, the viscosity of the polymer solution and the infiltration into the TiO2 layer mainly affects the efficiency of the solar cell. Another approach to increase the efficiency is the development of new hole-conducting polymers that absorb over a wide spectral range and which are adjusted to the energy levels of TiO2. Also new concepts, for example, the combination of thiophene- and phenyl-units into a copolymer are investigated in more detail. In summary, important parameters influencing the properties of hybrid solar cells are identified and discussed in more detail. For some limiting factors concepts to overcome these limitations are presented. KW - hybride Solarzellen KW - Titandioxid KW - Sintern KW - Polymer KW - hybrid thin solar cells KW - titanium dioxide KW - thermal treatment KW - polymers Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-52619 ER - TY - JOUR A1 - Schattauer, Sylvia A1 - Reinhold, Beate A1 - Albrecht, Steve A1 - Fahrenson, Christoph A1 - Schubert, Marcel A1 - Janietz, Silvia A1 - Neher, Dieter T1 - Influence of sintering on the structural and electronic properties of TiO2 nanoporous layers prepared via a non-sol-gel approach JF - Colloid and polymer science : official journal of the Kolloid-Gesellschaft N2 - In this work, a nonaqueous method is used to fabricate thin TiO2 layers. In contrast to the common aqueous sol-gel approach, our method yields layers of anatase nanocrystallites already at low temperature. Raman spectroscopy, electron microscopy and charge extraction by linearly increasing voltage are employed to study the effect of sintering temperature on the structural and electronic properties of the nanocrystalline TiO2 layer. Raising the sintering temperature from 120 to 600 A degrees C is found to alter the chemical composition, the layer's porosity and its surface but not the crystal phase. The room temperature mobility increases from 2 x 10(-6) to 3 x 10(-5) cm(2)/Vs when the sinter temperature is increased from 400 to 600 A degrees C, which is explained by a better interparticle connectivity. Solar cells comprising such nanoporous TiO2 layers and a soluble derivative of cyclohexylamino-poly(p-phenylene vinylene) were fabricated and studied with regard to their structural and photovoltaic properties. We found only weak polymer infiltration into the oxide layer for sintering temperatures up to 550 A degrees C, while the polymer penetrated deeply into titania layers that were sintered at 600 A degrees C. Best photovoltaic performance was reached with a nanoporous TiO2 film sintered at 550 A degrees C, which yielded a power conversion efficiency of 0.5 %. Noticeably, samples with the TiO2 layer dried at 120 A degrees C displayed short-circuit currents and open circuit voltages only about 15-20 % lower than for the most efficient devices, meaning that our nonaqueous route yields titania layers with reasonable transport properties even at low sintering temperatures. KW - Nonaqueous sol-gel KW - Thin nanocrystalline TiO2 layer KW - Solar cells KW - Effect of sintering KW - Linearly increasing voltage (CELIV) KW - Polymer infiltration KW - Transport properties titania KW - Transient fluorescence Y1 - 2012 U6 - https://doi.org/10.1007/s00396-012-2708-9 SN - 0303-402X VL - 290 IS - 18 SP - 1843 EP - 1854 PB - Springer CY - New York ER -