TY  - JOUR
A1  - Richter, Lothar
A1  - Vollhardt, Dieter
T1  - Force measuring methods for determination of surface tension of liquids: A comparison
JF  - Tenside, surfactants, detergents
N2  - Three methods for the determination of the surface tension of liquids based on force measurements namely, the vertical plate method of Wilhelmy, the frame method of Lenard and the ring method of du Nouy are compared and studied in respect of a common principle of correction. It is shown that these three most important force-based methods allow the determination of the surface tension under static conditions. The force components of the corresponding liquid column below the measuring wire obtained for the straight part of the withdrawal curve up to the transition in its curved part provides exact surface tension values. The experimentally accessible value of the force component describes the physical background of the measured value correction contrary to the approximate equations obtained by mathematical way. Usually the determination of surface tension of liquids is based merely at the vertical plate method on exact equations thermodynamically derived whereas in the case of the frame and ring methods correction factors in approximate equations are used. At usual application of the force-based methods under the non-static condition of the withdrawal of a liquid column, the force maximum measured at withdrawal of the measuring object (plate, frame, or ring) is the basis for the determination of surface tension. In these cases, the measured surface tension values are compensated by correction equations for the frame and ring methods which are based on an correction factor and correction tables empirically obtained. The surface tension values obtained in this usual way agree with those obtained by using the force component of the corresponding liquid column below the measuring wire for the straight part of the withdrawal curve up to the transition in its curved part. Problems arising at the force measurements with increasing thickness of the measuring wires inside and outside the rings are discussed.
N2  - Drei auf Kraftmessungen basierende Methoden zur Bestimmung der Oberflächenspannung von Flüssigkeiten, nämlich die Vertikalplattenmethode von Wilhelmy, die Bügelmethode von Lenard und die Ringmethode von du Noüy werden miteinander verglichen und auf ein experimentell zugängliches gemeinsames Korrekturprinzip hin untersucht. Auf Basis der Messresultate wird demonstriert, dass diese drei wichtigsten auf Kraftmessungen basierenden Methoden eine exakte Bestimmung der Oberflächenspannung ermöglichen. Dies basiert auf Berücksichtigung der Kraftkomponente der entsprechenden Flüssigkeitssäule unterhalb des Messdrahtes, der für die Austauchgerade bis zum Übergang in den gekrümmten Teil der Austauchkurve erhalten wird. Der experimentell zugängliche Wert der Kraftkomponente beschreibt den physikalischen Hintergrund der Messwertkorrektur im Gegensatz zu den auf mathematischen Weg erhaltenen Näherungsgleichungen. Gebräuchlicher Weise basiert die Bestimmung der Oberflächenspannung von Flüssigkeiten lediglich bei der Vertikalplattenmethode auf thermodynamisch-exakt ableitbaren Gleichungen, während bei Bügel- und Ringmethode Korrekturfaktoren für Näherungsgleichungen bzw. Korrekturtabellen üblich sind. Die so erhaltenen Oberflächenspannungswerte stimmen mit denen überein, die unter Berücksichtigung der Kraftkomponente der entsprechenden Flüssigkeitssäule unterhalb des Messdrahtes erhalten werden. Probleme, die mit zunehmender Dicke des Messdrahtes innerhalb und außerhalb des Rings entstehen, werden diskutiert.
T2  - Kraftmessungsmethoden zur Bestimmung der Oberflächenspannung von Flüssigkeiten: Ein Vergleich
KW  - surface tension
KW  - force methods
Y1  - 2006
U6  - https://doi.org/10.3139/113.100314
SN  - 0932-3414
VL  - 43
IS  - 5
SP  - 256
EP  - 261
PB  - Hanser
CY  - München
ER  - 
TY  - BOOK
A1  - Buder, Margret
A1  - Dreßler, Jutta
A1  - Kaden, Klaus
A1  - Kulke, Elmar
A1  - Lüdke, Norbert
A1  - Richter, Dieter
A1  - Vogt, Jürgen
T1  - Geografie : Hauptband Klasse 9/10 ; Ausgabe Brandenburg
Y1  - 2004
SN  - 3-06-040953-6
PB  - Cornelsen-Verl.
CY  - Berlin
ER  - 
TY  - BOOK
A1  - Buder, Margret
A1  - Dreßler, Jutta
A1  - Gewand, Ulrich
A1  - Kaden, Klaus
A1  - Lüdtke, Norbert
A1  - Richter, Dieter
A1  - Vogt, Jürgen
A1  - Weinert, Gudrun
ED  - Kulke, Elmar
ED  - Richter, Dieter
T1  - Geografie : Hauptband Klasse 7 ; Ausgabe Sachsen
Y1  - 2004
SN  - 3-06-040792-4
PB  - Cornelsen
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Worseck, Gabor
A1  - Prochaska, J. Xavier
A1  - McQuinn, Matthew
A1  - Dall'Aglio, Aldo
A1  - Fechner, Cora
A1  - Hennawi, Joseph F.
A1  - Reimers, Dieter
A1  - Richter, Philipp
A1  - Wisotzki, Lutz
T1  - The end of Helium Reionization at z similar or equal to 2.7 Inferred  from cosmic variance in HST/COS He II Ly alpha Absorption spectra
JF  - The astrophysical journal : an international review of spectroscopy and astronomical physics ; Part 2, Letters
N2  - We report on the detection of strongly varying intergalactic He II absorption in HST/COS spectra of two z(em) similar or equal to 3 quasars. From our homogeneous analysis of the He II absorption in these and three archival sightlines, we find a marked increase in the mean He II effective optical depth from <tau(eff, He II)> similar or equal to 1 at z similar or equal to 2.3 to <tau(eff, He II)> greater than or similar to 5 at z similar or equal to 3.2, but with a large scatter of 2 less than or similar to tau(eff, He II) less than or similar to 5 at 2.7 < z < 3 on scales of similar to 10 proper Mpc. This scatter is primarily due to fluctuations in the He II fraction and the He II-ionizing background, rather than density variations that are probed by the coeval Hi forest. Semianalytic models of He II absorption require a strong decrease in the He II-ionizing background to explain the strong increase of the absorption at z greater than or similar to 2.7, probably indicating He II reionization was incomplete at z(reion) greater than or similar to 2.7. Likewise, recent three-dimensional numerical simulations of He II reionization qualitatively agree with the observed trend only if He II reionization completes at z(reion) similar or equal to 2.7 or even below, as suggested by a large tau(eff, He II) greater than or similar to 3 in two of our five sightlines at z < 2.8. By doubling the sample size at 2.7 less than or similar to z less than or similar to 3, our newly discovered He II sightlines for the first time probe the diversity of the second epoch of reionization when helium became fully ionized.
KW  - dark ages, reionization, first stars
KW  - diffuse radiation
KW  - intergalactic medium
KW  - quasars: absorption lines
KW  - quasars: individual (SDSS J092447.36+485242.8, SDSS J110155.74+105302.3)
Y1  - 2011
U6  - https://doi.org/10.1088/2041-8205/733/2/L24
SN  - 2041-8205
VL  - 733
IS  - 2
PB  - IOP Publ. Ltd.
CY  - Bristol
ER  - 
TY  - JOUR
A1  - Forssmann, Wolf-Georg
A1  - Tillmann, Hanns-Christian
A1  - Hock, Dieter
A1  - Forssmann, Kristin
A1  - Bernasconi, Corrado
A1  - Forssmann, Ulf
A1  - Richter, Rudolf
A1  - Hocher, Berthold
A1  - Pfuetzner, Andreas
T1  - Pharmacokinetic and Pharmacodynamic Characteristics of Subcutaneously Applied PTH-1-37
JF  - German politics
N2  - Background/Aims: Parathyroid hormone (PTH) derivatives exert pronounced renal and osteoanabolic properties when given intermittently. The current study was performed to assess the pharmacokinetic and pharmacodynamic properties as well as safety of subcutaneously applied PTH-1-37 after repeated dosing in healthy subjects. Methods: This randomized, double-blind, dose-escalating, placebo and active comparator controlled study was conducted in 33 healthy postmenopausal women. Subjects were allocated to one of five treatment options: 10, 20, or 40 mu g PTH-1-37, 20 mu g PTH-1-34 or placebo, administered as once daily subcutaneous doses for three days. Plasma drug concentrations and serum levels of endogenous PTH-1-84, and calcium as markers of biological activity were monitored during the treatment. Results: PTH was absorbed rapidly from the subcutaneous tissue with a median t(max) of 30 minutes for 20 and 40 mu g of PTH-1-37. t(max) was 45 minutes for 20 mu g PTH-1-34. Elimination half-lives were estimated as 76 +/- 34 min and 70 +/- 13 min for 20 mu g and 40 mu g PTH-1-37 (mean +/- SD), and 78 +/- 34 for 20 mu g PTH-1-34. Both PTH fragments (PTH-1-37 and PTH-1-34) increased serum calcium. For PTH-1-37 the effect on serum calcium was dose-dependent. Suppression of endogenous PTH-1-84 was seen after the application of both PTH-1-37 and PTH-1-34. During the study period, the subjects experienced no unexpected or serious adverse events. Conclusions: PTH-1-37 is rapidly absorbed after s.c. injection, has a short plasma elimination half-life, and does not accumulate during multiple dosing. Biological activity was demonstrated by rising serum calcium and decreasing endogenous PTH-1-84 in blood plasma. The study drugs were well tolerated and safe. Our investigation presents data that PTH-1-37 is an excellent drug candidate for intervening with syndromes of dysregulation of calcium metabolism. (C) 2016 The Author(s) Published by S. Karger AG, Basel
KW  - Pharmacokinetics
Y1  - 2016
U6  - https://doi.org/10.1159/000443453
SN  - 1420-4096
SN  - 1423-0143
VL  - 41
SP  - 507
EP  - 518
PB  - Karger
CY  - Basel
ER  - 
TY  - BOOK
A1  - Buder, Margret
A1  - Richter, Dieter
A1  - Weinert, G.
T1  - Geografie : Arbeitsheft Klasse 5 ; Ausgabe Mecklenburg-Vorpommern
Y1  - 2001
SN  - 3-06-040574-3
PB  - Volk-und-Wissen-Verl.
CY  - Berlin
ER  - 
TY  - BOOK
A1  - Buder, Margret
A1  - Richter, Dieter
A1  - Weinert, G.
T1  - Geografie : Arbeitsheft Klasse 5 ; Ausgabe Sachsen
Y1  - 2001
SN  - 3-06-040573-5
PB  - Volk-und-Wissen-Verl.
CY  - Berlin
ER  - 
TY  - BOOK
A1  - Buder, Margret
A1  - Richter, Dieter
A1  - Weinert, G.
T1  - Geografie : Arbeitsheft Klasse 5 ; Ausgabe Thüringen
Y1  - 2001
SN  - 3-06-040575-2
PB  - Volk und Wissen
CY  - Berlin
ER  - 
TY  - GEN
A1  - Schulze, Patricia S. C.
A1  - Bett, Alexander J.
A1  - Bivour, Martin
A1  - Caprioglio, Pietro
A1  - Gerspacher, Fabian M.
A1  - Kabaklı, Özde Ş.
A1  - Richter, Armin
A1  - Stolterfoht, Martin
A1  - Zhang, Qinxin
A1  - Neher, Dieter
A1  - Hermle, Martin
A1  - Hillebrecht, Harald
A1  - Glunz, Stefan W.
A1  - Goldschmidt, Jan Christoph
T1  - 25.1% high-efficiency monolithic perovskite silicon tandem solar cell with a high bandgap perovskite absorber
T2  - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe
N2  - Monolithic perovskite silicon tandem solar cells can overcome the theoretical efficiency limit of silicon solar cells. This requires an optimum bandgap, high quantum efficiency, and high stability of the perovskite. Herein, a silicon heterojunction bottom cell is combined with a perovskite top cell, with an optimum bandgap of 1.68 eV in planar p-i-n tandem configuration. A methylammonium-free FA(0.75)Cs(0.25)Pb(I0.8Br0.2)(3) perovskite with high Cs content is investigated for improved stability. A 10% molarity increase to 1.1 m of the perovskite precursor solution results in approximate to 75 nm thicker absorber layers and 0.7 mA cm(-2) higher short-circuit current density. With the optimized absorber, tandem devices reach a high fill factor of 80% and up to 25.1% certified efficiency. The unencapsulated tandem device shows an efficiency improvement of 2.3% (absolute) over 5 months, showing the robustness of the absorber against degradation. Moreover, a photoluminescence quantum yield analysis reveals that with adapted charge transport materials and surface passivation, along with improved antireflection measures, the high bandgap perovskite absorber has the potential for 30% tandem efficiency in the near future.
T3  - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1197 
KW  - heterojunction silicon solar cells
KW  - interfaces
KW  - perovskite solar cells
KW  - tandem solar cells
KW  - thin films
Y1  - 2020
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-525668
SN  - 1866-8372
IS  - 7
ER  - 
TY  - JOUR
A1  - Sini, Gjergji
A1  - Schubert, Marcel
A1  - Risko, Chad
A1  - Roland, Steffen
A1  - Lee, Olivia P.
A1  - Chen, Zhihua
A1  - Richter, Thomas V.
A1  - Dolfen, Daniel
A1  - Coropceanu, Veaceslav
A1  - Ludwigs, Sabine
A1  - Scherf, Ullrich
A1  - Facchetti, Antonio
A1  - Frechet, Jean M. J.
A1  - Neher, Dieter
T1  - On the Molecular Origin of Charge Separation at the Donor-Acceptor Interface
JF  - Advanced energy materials
N2  - Fullerene-based acceptors have dominated organic solar cells for almost two decades. It is only within the last few years that alternative acceptors rival their dominance, introducing much more flexibility in the optoelectronic properties of these material blends. However, a fundamental physical understanding of the processes that drive charge separation at organic heterojunctions is still missing, but urgently needed to direct further material improvements. Here a combined experimental and theoretical approach is used to understand the intimate mechanisms by which molecular structure contributes to exciton dissociation, charge separation, and charge recombination at the donor-acceptor (D-A) interface. Model systems comprised of polythiophene-based donor and rylene diimide-based acceptor polymers are used and a detailed density functional theory (DFT) investigation is performed. The results point to the roles that geometric deformations and direct-contact intermolecular polarization play in establishing a driving force ( energy gradient) for the optoelectronic processes taking place at the interface. A substantial impact for this driving force is found to stem from polymer deformations at the interface, a finding that can clearly lead to new design approaches in the development of the next generation of conjugated polymers and small molecules.
KW  - donor-acceptor interfaces
KW  - energy gradients
KW  - geometrical deformations
KW  - nonfullerene acceptors
KW  - organic photovoltaics
KW  - photocurrent generation
KW  - polymer solar cells
Y1  - 2018
U6  - https://doi.org/10.1002/aenm.201702232
SN  - 1614-6832
SN  - 1614-6840
VL  - 8
IS  - 12
PB  - Wiley-VCH
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Schulze, Patricia S. C.
A1  - Bett, Alexander J.
A1  - Bivour, Martin
A1  - Caprioglio, Pietro
A1  - Gerspacher, Fabian M.
A1  - Kabaklı, Özde Ş.
A1  - Richter, Armin
A1  - Stolterfoht, Martin
A1  - Zhang, Qinxin
A1  - Neher, Dieter
A1  - Hermle, Martin
A1  - Hillebrecht, Harald
A1  - Glunz, Stefan W.
A1  - Goldschmidt, Jan Christoph
T1  - 25.1% high-efficiency monolithic perovskite silicon tandem solar cell with a high bandgap perovskite absorber
JF  - Solar RRL
N2  - Monolithic perovskite silicon tandem solar cells can overcome the theoretical efficiency limit of silicon solar cells. This requires an optimum bandgap, high quantum efficiency, and high stability of the perovskite. Herein, a silicon heterojunction bottom cell is combined with a perovskite top cell, with an optimum bandgap of 1.68 eV in planar p-i-n tandem configuration. A methylammonium-free FA(0.75)Cs(0.25)Pb(I0.8Br0.2)(3) perovskite with high Cs content is investigated for improved stability. A 10% molarity increase to 1.1 m of the perovskite precursor solution results in approximate to 75 nm thicker absorber layers and 0.7 mA cm(-2) higher short-circuit current density. With the optimized absorber, tandem devices reach a high fill factor of 80% and up to 25.1% certified efficiency. The unencapsulated tandem device shows an efficiency improvement of 2.3% (absolute) over 5 months, showing the robustness of the absorber against degradation. Moreover, a photoluminescence quantum yield analysis reveals that with adapted charge transport materials and surface passivation, along with improved antireflection measures, the high bandgap perovskite absorber has the potential for 30% tandem efficiency in the near future.
KW  - heterojunction silicon solar cells
KW  - interfaces
KW  - perovskite solar cells
KW  - tandem solar cells
KW  - thin films
Y1  - 2020
VL  - 4
IS  - 7
PB  - John Wiley & Sons, Inc.
CY  - New Jersey
ER  -