TY - THES A1 - Lettau, Kristian T1 - Katalytische molekular geprägte Polymere : Herstellung und Anwendung in einem Thermistor T1 - Catalytically molecular imprinted polymers : synthesis and application in a thermistor N2 - Biomakromoleküle sind in der Natur für viele Abläufe in lebenden Organismen verantwortlich. Dies reicht vom Aufbau der extrazellulären Matrix und dem Cytoskelett über die Erkennung von Botenstoffen durch Rezeptoren bis hin zur Katalyse der verschiedensten Reaktionen in den Zellen selbst. Diese Aufgaben werden zum größten Teil von Proteinen übernommen, und besonders das spezifische Erkennen der Interaktionspartner ist für alle diese Moleküle äußerst wichtig, um eine fehlerfreie Funktion zu gewährleisten. Als Alternative zur evolutiven Erzeugung von optimalen Bindern und Katalysatoren auf der Basis von Aminosäuren und Nukleotiden wurden von Wulff, Shea und Mosbach synthetische molekular geprägte Polymere (molecularly imprinted polymers, MIPs) konzipiert. Das Prinzip dieser künstlichen Erkennungselemente beruht auf der Tatsache, dass sich funktionelle Monomere spezifisch um eine Schablone (Templat) anordnen. Werden diese Monomere dann vernetzend polymerisiert, entsteht ein Polymer mit molekularen Kavitäten, in denen die Funktionalitäten komplementär zum Templat fixiert sind. Dadurch ist die selektive Bindung des Templats in diese Kavitäten möglich. Aufgrund ihrer hohen chemischen und thermischen Stabilität und ihrer geringen Kosten haben “bio-inspirierte” molekular geprägte Polymere das Potential, biologische Erkennungselemente in der Affinitätschromatographie sowie in Biosensoren und Biochips zu ersetzen. Trotz einiger publizierter Sensorkonfigurationen steht der große Durchbruch noch aus. Ein Hindernis für Routineanwendungen ist die Signalgenerierung bei Bindung des Analyten an das Polymer. Eine Möglichkeit für die markerfreie Detektion ist die Benutzung von Kalorimetern, die Bindungs- oder Reaktionswärmen direkt messen können. In der Enzymtechnologie wird der Enzym-Thermistor für diesen Zweck eingesetzt, da enzymatische Reaktionen eine Enthalpie in einer Größenordnung von 5 – 100 kJ/mol besitzen. In dieser Arbeit wird die Herstellung von katalytisch geprägten Polymeren nach dem Verfahren des Oberflächenprägens erstmalig beschrieben. Die Methode zur Immobilisierung des Templats auf der Oberfläche von porösem Kieselgel sowie die Polymerzusammensetzung wurden optimiert. Weiter wird die Evaluation der katalytischen Eigenschaften über einen optischen Test, sowie das erste Mal die Kombination eines kalorimetrischen Transduktors – des Thermistors – mit der Analyterkennung durch ein katalytisch aktives MIP gezeigt. Bei diesen Messungen konnte zum ersten Mal gleichzeitig die Bindung/Desorption, sowie die katalytische Umwandlung des Substrats durch konzentrationsabhängige Wärmesignale nachgewiesen werden. N2 - Bio macromolecules are responsible in nature for many reactions in living organisms. This reaches from the structure of the extra cellular matrix and the cytoskeleton over the recognition of ligands by receptors up to the catalysis of the most diverse reactions in the cells themselves. These tasks are taken over to the largest part by proteins, and particularly specific recognizing of the interaction partners is extremely important for all these molecules, in order to ensure an error free function. As alternative to the evolutionary production of optimal binders and catalysts on the basis of amino acids and nucleotides, synthetic molecularly imprinted polymer (MIPs) were invented by Wulff, Shea and Moosbach. The principle of these artificial recognition elements is based on the fact that functional monomers specifically arrange themselves around a template. If these monomers are copolymerized with crosslinking monomers, a polymer with molecular cavities is created, in which the functionalities are fixed complementary to the template. Thus the selective binding of the template is possible into these cavities. Due to their high chemical and thermal stability and their small costs "bioinspired" molecularly imprinted polymers have the potential to replace biological recognition elements in affinity chromatography as well as in biosensors and biochips. Despite some published sensor configurations the large break-through is still pending. An obstacle for routine application of is the signal generation on connection of the analyte to the polymer. A possibility for marker-free detection is the use of calorimeters, which can measure heats of reaction or adsorption directly. In enzyme technology the enzyme thermistor is used for this purpose, as enzymatic reactions possess enthalpies in an order of 5 - 100 kJ/mol. In this work the production of catalytically imprinted polymers is described for the first time by the procedure of surface imprinting. The method for immobilization of the template on the surface of porous silicagel as well as the polymer composition were optimized. The evaluation of the catalytic characteristics is shown by an optical test, as well as the first time the combination of a calorimetric transducer - the thermistor - with the analyte recognition by a catalytically active MIP. With these measurements for the first time the binding/desorption, as well as the catalytic transformation of the substrate could be proven at the same time by concentration-dependent heat signals. KW - Katalyse KW - molekular geprägte Polymere KW - Kalorimetrie KW - Enzymmodelle KW - Biosensoren KW - catalysis KW - molecularly imprinted polymers KW - calorimetry KW - enzyme models KW - biosensors Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-14804 ER - TY - THES A1 - Karras, Manfred T1 - Synthesis of enantiomerically pure helical aromatics such as NHC ligands and their use in asymmetric catalysis T1 - Die Synthese von enantiomerenreinen helikalen Aromaten wie NHC Liganden und deren Anwendung in asymmetrischer Katalyse N2 - Diese Arbeit beschäftigt sich mit der enantiomerenreinen Synthese helikaler, aromatischer Verbindungen. Verschiedene Verbindungen dieses Typs wurden erfolgreich hergestellt und charakterisiert. Desweiteren wurden einige der neuen Verbindungen in Übergangsmetallkomplexe eingebaut und diese dann als Katalysatoren für Metathese und Kreuzkupplungen getestet. Einer der getesteten Katalysatoren zeigte vielversprechende Ergebnisse in der asymmetrischen Olefinmetathese. Die Struktur des neuen Katalysators wurde untersucht. Anhand der Struktur des neuen Katalysators wurden Rückschlüsse auf einen möglichen Mechanismus gezogen. N2 - Various ways of preparing enantiomerically pure 2-amino[6]helicene derivatives were explored. Ni(0) mediated cyclotrimerization of enantiopure triynes provided (M)- and (P)-7,8-bis(p-tolyl)hexahelicene-2-amine in >99% ee as well as its benzoderivative in >99% ee. The stereocontrol was found to be inefficient for a 2- aminobenzo[6]helicene congener with an embedded five-membered ring. Helically chiral imidazolium salts bearing one or two helicene moieties have been synthesized and applied in enantioselective [2+2+2] cyclotrimerization catalyzed by an in situ formed Ni(0)-NHC complex. The synthesis of the first helically chiral Pd- and Ru-NHC complexes and their application in enantioselective catalysis was demonstrated. The latter shows promising results in enantioselective olefin metathesis reactions. A mechanistic proposal for asymmetric ring closing metathesis is provided. KW - helicene KW - catalysis KW - NHC KW - asymmetric KW - Helicen KW - Katalyse KW - NHC KW - asymmetrisch Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-421497 ER - TY - THES A1 - Lama, Sandy M. G. T1 - Functionalization of Porous Carbon Materials with Heteroatoms and Application as Supports in Industrial Heterogeneous Catalysis T1 - Funktionalisierung von porösen Kohlenstoffmaterialien mit Heteroatomen und Anwendung als Träger in der industriellen heterogenen Katalyse N2 - Due to a challenging population growth and environmental changes, a need for new routes to provide required chemicals for human necessities arises. An effective solution discussed in this thesis is industrial heterogeneous catalysis. The development of an advanced industrial heterogeneous catalyst is investigated herein by considering porous carbon nano-material as supports and modifying their surface chemistry structure with heteroatoms. Such modifications showed a significant influence on the performance of the catalyst and provided a deeper insight regarding the interaction between the surface structure of the catalyst and the surrounding phase. This thesis contributes to the few present studies about heteroatoms effect on the catalyst performance and emphasizes on the importance of understanding surface structure functionalization in a catalyst in different phases (liquid and gaseous) and for different reactions (hydrogenolysis, oxidation, and hydrogenation/ polymerization). Herein, the heteroatoms utilized for the modifications are hydrogen (H), oxygen (O), and nitrogen (N). The heteroatoms effect on the metal particle size, on the polarity of the support/ the catalyst, on the catalytic performance (activity, selectivity, and stability), and on the interaction with the surrounding phase has been explored. First hierarchical porous carbon nanomaterials functionalized with heteroatoms (N) is synthesized and applied as supports for nickel nanoparticles for hydrogenolysis process of kraft lignin in liquid phase. This reaction has been performed in batch and flow reactors for three different catalysts, two of comparable hierarchical porosity, yet one is modified with N and the other is not, and a third is a prepared catalyst from a commercial carbon support. The reaction production and analyses show that the catalysts with hierarchical porosity perform catalytically much better than in presence of a commercial carbon support with lower surface area. Moreover, the modification with N-heteroatoms enhanced the catalytic performance because the heteroatom modified porous carbon material with nickel nanoparticles catalyst (Ni-NDC) performed highest among the other catalysts. In the flow reactor, Ni-NDC selectively degraded the ether bonds (β-O-4) in kraft lignin with an activity of 2.2 x10^-4 mg lignin mg Ni-1 s-1 for 50 h at 350°C and 3.5 mL min-1 flow, providing ~99 % conversion to shorter chained chemicals (mainly guaiacol derivatives). Then, the functionalization of carbon surface was further studied in selective oxidation of glucose to gluconic acid using < 1 wt. % of gold (Au) deposited on the previously-mentioned synthesized carbon (C) supports with different functionalities (Au-CGlucose, Au-CGlucose-H, Au-CGlucose-O, Au-CGlucoseamine). Except for Au-CGlucose-O, the other catalysts achieved full glucose conversion within 40-120 min and 100% selectivity towards gluconic acid with a maximum activity of 1.5 molGlucose molAu-1 s-1 in an aqueous phase at 45 °C and pH 9. Each heteroatom influenced the polarity of the carbon differently, affecting by that the deposition of Au on the support and thus the activity of the catalyst and its selectivity. The heteroatom effect was further investigated in a gas phase. The Fischer-Tropsch reaction was applied to convert synthetic gas (CO and H2) to short olefins and paraffins using surface-functionalized carbon nanotubes (CNTs) with heteroatoms as supports for ion (Fe) deposition in presence and absence of promoters (Na and S). The results showed the promoted Fe-CNT doped with nitrogen catalyst to be stable up to 180 h and selective to the formation of olefins (~ 47 %) and paraffins (~6 %) with a conversion of CO ~ 92 % at a maximum activity of 94 *10^-5 mol CO g Fe-1 s-1. The more information given regarding this topic can open wide range of applications not only in catalysis, but in other approaches as well. In conclusion, incorporation of heteroatoms can be the next approach for an advanced industrial heterogeneous catalyst, but also for other applications (e.g. electrocatalysis, gas adsorption, or supercapacitors). N2 - Herausforderungen wie Bevölkerungszuwachs und Umweltveränderungen erfordern neue Wege, chemische Substanzen zu erzeugen, um menschliche Anforderungen zu befriedigen. Eine mögliche effektive Lösung dafür, welche in dieser Arbeit diskutiert wird ist die industrielle heterogene Katalyse. Es werden unter dem Einsatz poröser Kohlenstoffträger neue industrielle Katalysatoren untersucht und entwickelt wobei die Oberflächenstruktur dieser Trägermaterialien mit Heteroatomen modifiziert wird. Diese Modifikationen zeigten einen signifikanten Einfluss auf die Eigenschaften der Katalysatoren und erlaubten Rückschlüsse hinsichtlich der Interaktion zwischen Katalysatoroberfläche und umgebender Phase. Die vorliegende Arbeit trägt zu einigen wenigen existierenden Studien bei die sich mit den Einflüssen solcher Heteroatome auf Katalysatoren beschäftigen. Es wird versucht, die Wichtigkeit dieser Oberflächeneigenschaften in Reaktionen (Hydrogenolyse, Oxidation, Hydrierung/ Polymerisation) in verschiedenen Phasen (flüssig oder gasförmig) zu verstehen. Die für die Modifikationen eingesetzten Heteroatome sind Wasserstoff (H), Sauerstoff (O) und Stickstoff (N). Ihr Effekt auf die Größe der Metallpartikel, die Polarität der Träger bzw. Katalysatoren, die eigentlichen katalytischen Eigenschaften und die Interaktion mit der umgebenden Phase wurde untersucht. Zuerst wurden hierarchisch poröse Kohlenstoffmaterialien hergestellt, die mit Stickstoff als Heteroatome funktionalisiert wurden. Diese wurden als Trägermaterialien für Nickel-Nanopartikel in der Hydrogenolyse von Kraft Lignin in flüssiger Phase eingesetzt. Diese Reaktion wurde mit drei unterschiedlichen Katalysatoren in Batch- und Flussreaktoren durchgeführt. Zwei der Katalysatoren hatten vergleichbare hierarchische Porosität. Einer davon war mit Heteroatomen funktionalisiert, einer dagegen nicht. Ein dritter Katalysator wurde mit einem kommerziell erhältlichen Kohlenstoffmaterial hergestellt. Die Reaktion zeigte, dass die Katalysatoren mit hierarchischer Porosität deutlich bessere Eigenschaften zeigen als das kommerzielle Trägermaterial mit geringerer Oberfläche. Darüber hinaus zeigte sich, dass die Modifizierung mit Stickstoffatomen die katalytischen Eigenschaften verbessert, da das modifizierte Kohlenstoffmaterial mit den Nickelpartikeln (Ni-NDC) die besten Ergebnisse aller untersuchten Katalysatoren zeigte. Im Durchflussreaktor wurden von Ni-NDC die Etherbindungen des Kraft Lignins (β-O-4) selektiv mit einer Aktivität von 2.2 x10^-4 mg lignin mg Ni-1 s-1 für 50 h bei 99% Umsatz zu kurzkettigeren Strukturen (hauptsächlich Guajakol-Derivat) gespalten. Außerdem wurde der Einfluss der Funktionalisierung der Kohlenstoffoberfläche in der selektiven Oxidation von Glucose zu Gluconsäure mit 1 Gew.% Gold (Au) auf den vorher angesprochenen Kohlenstoffträgermaterialien mit unterschiedlichen Oberflächenfunktionalitäten (Au-CGlucose, Au-CGlucose-H, Au-CGlucose-O, Au-CGlucoseamine) untersucht. Mit Ausnahme von Au-CGlucose-O erreichten alle Katalysatoren innerhalb von 40-120 min 100% Glucose Umsatz bei 100%iger Selektivität zu Gluconsäure und einer maximalen katalytischen Aktivität von 1.5 molGlucose molAu-1 s-1 in wässriger Phase bei 45°C und pH 9. Die unterschiedlichen Heteroatome wirkten sich unterschiedlich auf die Polarität der Kohlenstoffe und damit auch auf die Abscheidung der Goldpartikel auf die Trägermaterialien und die Katalysatoraktivität und -selektivität aus. Der Einfluss der Heteroatome wurde außerdem in einer Gasphasenreaktion untersucht. Die Fischer-Tropsch Reaktion kam zum Einsatz um Synthesegas (CO und H2) mit Hilfe von Katalysatoren bestehend aus Eisen (Fe) auf Heteroatomfunktionalisierten Kohlenstoffnanoröhrchen (engl. Carbon nanotubes, CNTs) in Gegenwart und Abwesenheit von Promotoren (Na und S) zu kurzkettigen Olefinen und Paraffinen umzuwandeln. Die Ergebnisse zeigten dass die Fe-CNT Katalysatoren mit Promotoren und stickstoffdotierten Trägern bis zu 180 h stabil waren und Olefine (~ 47 %) sowie Paraffine (~6 %) mit guten Selektivitäten bei einem CO Umsatz von 92% und einer maximalen Aktivität von 94 *10^-5 mol CO gFe-1 s-1 hergestellt werden konnten. Je mehr Informationen zu diesem Thema zur Verfügung gestellt werden, kann dies zu einer großen Bandbreite von Anwendungen nicht nur in der Katalyse, sondern auch in anderen Ansätzen beitragen. Zusammenfassend kann der Einbau von Heteroatomen der nächste Ansatz für einen fortgeschrittenen industriellen heterogenen Katalysator sein, aber auch für andere Anwendungen (z.B. Elektrokatalyse, Gasadsorption oder Superkondensatoren). KW - catalysis KW - carbon material KW - carbon supports KW - glucose oxidation KW - Kraft lignin hydrogenolysis KW - Fischer-Tropsch Synthesis KW - Syngas Hydrogenation KW - gold-carbon catalysts KW - nickel-carbon catalysts KW - iron-carbon nanotube catalysts KW - hierarchical porosity KW - heteroatom modification KW - catalyst functionalization KW - Katalyse KW - Kohlenstoffmaterial KW - Kohlenstoffträger KW - Glukoseoxidation KW - Kraftlignin KW - Hydrogenolyse KW - Fischer-Tropsch-Synthese KW - Syngashydrierung KW - Gold-Kohlenstoff-Katalysatoren KW - Nickel-Kohlenstoff-Katalysatoren KW - Eisen-Kohlenstoff-Nanoröhrchen-Katalysatoren KW - hierarchische Porosität KW - Heteroatom-Modifikation KW - Funktionalisierung von Katalysatoren Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-415797 ER - TY - THES A1 - Zhao, Yuhang T1 - Synthesis and surface functionalization on plasmonic nanoparticles for optical applications N2 - This thesis focuses on the synthesis of novel functional materials based on plasmonic nanoparticles. Three systems with targeted surface modification and functionalization have been designed and synthesized, involving modified perylenediimide doped silica-coated silver nanowires, polydopamine or TiO2 coated gold-palladium nanorods and thiolated poly(ethylene glycol) (PEG-SH)/dodecanethiol (DDT) modified silver nanospheres. Their possible applications as plasmonic resonators, chiral sensors as well as photo-catalysts have been studied. In addition, the interaction between silver nanospheres and 2,3,5,6-Tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) molecules has also been investigated in detail. In the first part of the thesis, surface modification on Ag nanowires (NWs) with optimized silica coating through a modified Stöber method has been firstly conducted, employing sodium hydroxide (NaOH) to replace ammonia solution (NH4OH). The coated silver nanowires with a smooth silica shell have been investigated by single-particle dark-field scattering spectroscopy, transmission electron microscopy and electron-energy loss spectroscopy to characterize the morphologies and structural components. The silica-coated silver nanowires can be further functionalized with fluorescent molecules in the silica shell via a facile one-step coating method. The as-synthesized nanowire is further coupled with a gold nanosphere by spin-coating for the application of the sub-diffractional chiral sensor for the first time. The exciton-plasmon-photon interconversion in the system eases the signal detection in the perfectly matched 1D nanostructure and contributes to the high contrast of the subwavelength chiral sensing for the polarized light. In the second part of the thesis, dumbbell-shaped Au-Pd nanorods coated with a layer of polydopamine (PDA) or titanium dioxide (TiO2) have been constructed. The PDA- and TiO2- coated Au-Pd nanorods show a strong photothermal conversion performance under NIR illumination. Moreover, the catalytic performance of the particles has been investigated using the reduction of 4-nitrophenol (4-NP) as the model reaction. Under light irradiation, the PDA-coated Au-Pd nanorods exhibit a superior catalytic activity by increasing the reaction rate constant of 3 times. The Arrhenius-like behavior of the reaction with similar activation energies in the presence and absence of light irradiation indicates the photoheating effect to be the dominant mechanism of the reaction acceleration. Thus, we attribute the enhanced performance of the catalysis to the strong photothermal effect that is driven by the optical excitation of the gold surface plasmon as well as the synergy with the PDA layer. In the third part, the kinetic study on the adsorption of 2,3,5,6-Tetrafluoro-7,7,8,8-tetracyanoquino-dimethane (F4TCNQ) on the surface of Ag nanoparticles (Ag NPs) in chloroform has been reported in detail. Based on the results obtained from the UV-vis-NIR absorption spectroscopy, cryogenic transmission electron microscopy (cryo-TEM), scanning nano-beam electron diffraction (NBED) and electron energy loss spectroscopy (EELS), a two-step interaction kinetics has been proposed for the Ag NPs and F4TCNQ molecules. It includes the first step of electron transfer from Ag NPs to F4TCNQ indicated by the ionization of F4TCNQ, and the second step of the formation of Ag-F4TCNQ complex. The whole process has been followed via UV-vis-NIR absorption spectroscopy, which reveals distinct kinetics at two stages: the instantaneous ionization and the long-term complex formation. The kinetics and the influence of the molar ratio of Ag NPs/F4TCNQ molecules on the interaction between Ag NPs and F4TCNQ molecules in the organic solution are reported herein for the first time. Furthermore, the control experiment with silica-coated Ag NPs indicates that the charge transfer at the surface between Ag NPs and F4TCNQ molecules has been prohibited by a silica layer of 18 nm. KW - plasmonic nanoparticles KW - silica KW - polydopamine KW - TiO2 KW - chiral sensing KW - catalysis KW - surface interaction Y1 - 2021 ER -