TY - THES A1 - Imran ul-haq, Muhammad T1 - Synthesis of fluorinated polymers in supercritical carbon dioxide (scCO₂) T1 - Synthese von Fluorpolymeren in überkritischem Kohlendioxid (scCO₂) N2 - For the first time stabilizer-free vinylidene fluoride (VDF) polymerizations were carried out in homogeneous phase with supercritical CO₂. Polymerizations were carried out at 140°C, 1500 bar and were initiated with di-tert-butyl peroxide (DTBP). In-line FT-NIR (Fourier Transform- Near Infrared) spectroscopy showed that complete monomer conversion may be obtained. Molecular weights were determined via size-exclusion chromatography (SEC) and polymer end group analysis by 1H-NMR spectroscopy. The number average molecular weights were below 104 g∙mol−1 and polydispersities ranged from 3.1 to 5.7 depending on DTBP and VDF concentration. To allow for isothermal reactions high CO₂ contents ranging from 61 to 83 wt.% were used. The high-temperature, high-pressure conditions were required for homogeneous phase polymerization. These conditions did not alter the amount of defects in VDF chaining. Scanning electron microscopy (SEM) indicated that regular stack-type particles were obtained upon expansion of the homogeneous polymerization mixture. To reduce the required amount of initiator, further VDF polymerizations using chain transfer agents (CTAs) to control molecular weights were carried out in homogeneous phase with supercritical carbon dioxide (scCO₂) at 120 °C and 1500 bar. Using perfluorinated hexyl iodide as CTA, polymers of low polydispersity ranging from 1.5 to 1.2 at the highest iodide concentration of 0.25 mol·L-1 were obtained. Electrospray ionization- mass spectroscopy (ESI-MS) indicates the absence of initiator derived end groups, supporting livingness of the system. The “livingness” is based on the labile C-I bond. However, due to the weakness of the C-I bond perfluorinated hexyl iodide also contributes to initiation. To allow for kinetic analyses of VDF polymerizations the CTA should not contribute to initiation. Therefore, additional CTAs were applied: BrCCl3, C6F13Br and C6F13H. It was found that C6F13H does not contribute to initiation. At 120°C and 1500 bar kp/kt0.5~ 0.64 (L·mol−1·s−1)0.5 was derived. The chain transfer constant (CT) at 120°C has been determined to be 8·10−1, 9·10−2 and 2·10−4 for C6F13I, C6F13Br and C6F13H, respectively. These CT values are associated with the bond energy of the C-X bond. Moreover, the labile C-I bond allows for functionalization of the polymer to triazole end groups applying click reactions. After substitution of the iodide end group by an azide group 1,3 dipolar cycloadditions with alkynes yield polymers with 1,2,3 triazole end groups. Using symmetrical alkynes the reactions may be carried out in the absence of any catalyst. This end-functionalized poly (vinylidene fluoride) (PVDF) has higher thermal stability as compared to the normal PVDF. PVDF samples from homogeneous phase polymerizations in supercritical CO₂ and subsequent expansion to ambient conditions were analyzed with respect to polymer end groups, crystallinity, type of polymorphs and morphology. Upon expansion the polymer was obtained as white powder. Scanning electron microscopy (SEM) showed that DTBP derived polymer end groups led to stack-type particles whereas sponge- or rose-type particles were obtained in case of CTA fragments as end groups. Fourier-Transform Infrared spectroscopy and wide angle X-ray diffraction indicated that the type of polymorph, α or β crystal phase was significantly affected by the type of end group. The content of β-phase material, which is responsible for piezoelectricity of PVDF, is the highest for polymer with DTBP-derived end groups. In addition, the crystallinity of the material, as determined via differential scanning calorimetry is affected by the end groups and polymer molecular weights. For example, crystallinity ranges from around 26 % for DTBP-derived end groups to a maximum of 62 % for end groups originating from perfluorinated hexyl iodide for polymers with Mn ~2200 g·mol–1. Expansion of the homogeneous polymerization mixture results in particle formation by a non-optimized RESS (Rapid Expansion from Supercritical Solution) process. Thus, it was tested how polymer end groups affect the particles size distribution obtained from RESS process under controlled conditions (T = 50°C and P = 200 bar). In all RESS experiments, small primary PVDF with diameters less than 100 nm without the use of liquid solvents, surfactants, or other additives were produced. A strong correlation between particle size and particle size distribution with polymer end groups and molecular weight of the original material was observed. The smallest particles were found for RESS of PVDF with Mn~ 4000 g·mol–1 and PFHI (C6F13I) - derived end groups. N2 - Erstmalig gelang es, stabilisatorfreie Vinylidenfluorid (VDF)-Polymerisationen in homogener Phase mit überkritischem CO₂ (scCO₂) bis zu vollständigem Monomerumsatz durchzuführen. Die Homogenität während der Polymerisation wurde durch in-line Fourier-Transform Nahinfrarot Spektroskopie beobachtet. Für Polymerisationen bei 140 °C und 1500 bar wurde Di-tert-butylperoxid (DTBP) als Initiator verwendet. Es wurden Polymere mit einem Zahlenmittel der Molmasse kleiner 104 g·mol–1 und Polydispersitäten zwischen 3.1 und 5.7. erhalten. Um isotherme Reaktionen zu ermöglichen, wurden CO₂-Gehalte zwischen 61 und 83 wt.% verwendet. Die für die homogene Reaktionsführung erforderlichen hohen Drücke und Temperaturen haben keinen Einfluss auf die Mikrostruktur des Polymers. Zur Verringerung der Initiatorkonzentration wurden weitere Polymerisationen unter Verwendung von Kettentransferreagenzien (CTA) bei 120 °C und 1500 bar in homogener Phase mit scCO₂ durchgeführt. Perfluoriertes Hexyliodid als CTA ermöglicht kontrollierte radikalische Polymerisationen, wobei Polymere mit geringer Polydispersität zwischen 1.5 und 1.2 erhalten wurden. Endgruppenanalyse mit Elektronenspray-Ionisations-Massen¬spektro¬metrie (ESI-MS) zeigte, dass keine Initiatorendgruppen im Polymer enthalten sind. Diese Beobachtung unterstützt den lebenden Charakter der Polymerisationen und basiert auf einer labilen C-I-Bindung im Polymer. Aufgrund der schwachen C-I-Bindung trägt das perfluorierte Hexyliodid (C6F13I) auch zur Initiierung bei. Polymerisationen in Gegenwart von BrCCl3, C6F13Br und C6F13H zeigten, dass nur C6F13H keinen Beitrag zur Initiierung leistet. Bei 120 °C und 1500 bar wurde ein kp/kt0.5 von ~ 0.64 (L·mol−1·s−1)0.5 bestimmt, wobei kp der Wachstums- und kt der Terminierungsgeschwindigkeitskoeffizient sind. Die Kettentransfer¬konstanten (CT) bei 120°C betragen 8·10−1, 9·10−2 und 2·10−4 für C6F13I, C6F13Br und C6F13H. Die Änderung der CT-Werte lässt sich mit der zunehmenden Bindungsenergie in der Reihe C-I, C-Br und C-H erklären. Die labile C-I-Bindung ermöglicht eine Funktionalisierung des Polymers durch Click-Reaktionen. Nach Substitution der Iodid-Endgruppe durch eine Azidgruppe erfolgte eine katalysatorfreie 1,3-dipolare Cyclaoaddition mit Alkinen zu Polymeren mit 1,2,3-Triazol-Endgruppen. Dieses endfunktionalisierte PVDF besitzt im Vergleich zu konventionellem PVDF eine höhere thermische Stabilität. Nach der Expansion der Polymerisationsmischung mit scCO₂ auf Umgebungsbedingungen lag das Polymer als weißes Pulver vor, das im Hinblick auf z.B. Polymerendgruppen, Kristallinität, Gestalt und Größe der Partikel untersucht wurde. Rasterelektronenmikroskopie zeigte, dass Polymere mit DTBP-Endgruppen zu stapelförmigen Partikeln führen, während bei CTA-Fragmenten als Endgruppen schwamm- oder rosenartige Partikel erhalten wurden. Ergebnisse der FT-IR Spektroskopie und Weitwinkelröntgenbeugung zeigten, dass der höchste Gehalt an β-phasigem Material, der für die Piezoelektrizität des PVDF verantwortlich ist, für PVDF mit Initiatorendgruppen erhalten wurde. DSC (Differential Scanning Calorimetry) Messungen ergaben zudem, dass der Kristallinitätsgrad durch Endgruppen und Polymermasse beeinflusst wird. Die Expansion der homogenen Polymermischung kann als nicht-optimierter RESS-Prozess (Rapid Expanison from Supercritical Solution,) angesehen werden. Aus RESS Experimenten unter kontrollierten Bedingungen wurden jeweils nanoskalige primäre PVDF-Partikel ohne Verwendung von Lösungsmitteln, Tensiden oder anderen Additiven erhalten. Es besteht ein enger Zusammenhang zwischen einerseits der Partikelgröße und der Partikelgrößenverteilung und andererseits der Polymerkonzentration in scCO₂ vor der Expansion, bestimmt durch Polymerendgruppen und Molmassen der eingesetzten Materialien. KW - Synthese KW - Fluorpolymere KW - überkritisches Kohlendioxid (scCO₂) KW - Synthesis KW - fluorinated polymers KW - supercritical carbon dioxide (scCO₂) Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-19868 ER - TY - THES A1 - Bivigou Koumba, Achille Mayelle T1 - Design, Synthesis and Characterisation of Amphiphilic Symmetrical triblock copolymers by the RAFT process : their self-organisation in dilute and concentrated aqueous solutions T1 - Design, Synthese und Charakterisierung von amphiphilen symmetrischen Triblock-Copolymeren anhand des RAFT Prozesses : ihre Selbstorganisation in wässrigen verdünnten und höher konzentrierten Lösungen N2 - This work presents the synthesis and the self-assembly of symmetrical amphiphilic ABA and BAB triblock copolymers in dilute, semi-concentrated and highly concentrated aqueous solution. A series of new bifunctional bistrithiocarbonates as RAFT agents was used to synthesise these triblock copolymers, which are characterised by a long hydrophilic middle block and relatively small, but strongly hydrophobic end blocks. As hydrophilic A blocks, poly(N-isopropylacrylamide) (PNIPAM) and poly(methoxy diethylene glycol acrylate) (PMDEGA) were employed, while as hydrophobic B blocks, poly(4-tert-butyl styrene), polystyrene, poly(3,5-dibromo benzyl acrylate), poly(2-ethylhexyl acrylate), and poly(octadecyl acrylate) were explored as building blocks with different hydrophobicities and glass transition temperatures. The five bifunctional trithiocarbonates synthesised belong to two classes: the first are RAFT agents, which position the active group of the growing polymer chain at the outer ends of the polymer (Z-C(=S)-S-R-S-C(=S)-Z, type I). The second class places the active groups in the middle of the growing polymer chain (R-S-C(=S)-Z-C(=S)-S-R, type II). These RAFT agents enable the straightforward synthesis of amphiphilic triblock copolymers in only two steps, allowing to vary the nature of the hydrophobic blocks as well as the length of the hydrophobic and hydrophilic blocks broadly with good molar mass control and narrow polydispersities. Specific side reactions were observed among some RAFT agents including the elimination of ethylenetrithiocarbonate in the early stage of the polymerisation of styrene mediated by certain agents of the type II, while the use of the RAFT agents of type I resulted in retardation of the chain extension of PNIPAM with styrene. These results underline the need of a careful choice of RAFT agents for a given task. The various copolymers self-assemble in dilute and semi-concentrated aqueous solution into small flower-like micelles. No indication for the formation of micellar clusters was found, while only at high concentration, physical hydrogels are formed. The reversible thermoresponsive behaviour of the ABA and BAB type copolymer solutions in water with A made of PNIPAM was examined by turbidimetry and dynamic light scattering (DLS). The cloud point of the copolymers was nearly identical to the cloud point of the homopolymer and varied between 28-32 °C with concentrations from 0.01 to 50 wt%. This is attributed to the formation of micelles where the hydrophobic blocks are shielded from a direct contact with water, so that the hydrophobic interactions of the copolymers are nearly the same as for pure PNIPAM. Dynamic light scattering measurements showed the presence of small micelles at ambient temperature. The aggregate size dramatically increased above the cloud point, indicating a change of aggregate morphology into clusters due to the thermosensitivity of the PNIPAM block. The rheological behaviour of the amphiphilic BAB triblock copolymers demonstrated the formation of hydrogels at high concentrations, typically above 30-35 wt%. The minimum concentration to induce hydrogels decreased with the increasing glass transition temperatures and increasing length of the end blocks. The weak tendency to form hydrogels was attributed to a small share of bridged micelles only, due to the strong segregation regime occurring. In order to learn about the role of the nature of the thermoresponsive block for the aggregation, a new BAB triblock copolymer consisting of short polystyrene end blocks and PMDEGA as stimuli-responsive middle block was prepared and investigated. Contrary to PNIPAM, dilute aqueous solutions of PMDEGA and of its block copolymers showed reversible phase transition temperatures characterised by a strong dependence on the polymer composition. Moreover, the PMDEGA block copolymer allowed the formation of physical hydrogels at lower concentration, i.e. from 20 wt%. This result suggests that PMDEGA has a higher degree of water-swellability than PNIPAM. N2 - Die Arbeit behandelt die Synthese und das Selbstorganisationsverhalten von neuen funktionellen symmetrischen "stimuli-responsiven" Triblockcopolymeren ABA und BAB in wässrigen verdünnten und höher konzentrierten Lösungen. Neue symmetrische, bifunktionelle Bistrithiocarbonate wurden als RAFT-Agentien benutzt, um Triblockcopolymere mit langen hydrophilen (A) Innen- und kurzen hydrophoben (B) Außenblöcken zu synthetisieren. Als hydrophile A Blöcke wurden Poly(N-isopropylacrylamid) PNIPAM und Poly(methoxy diethylene glykol acrylat) PMDEGA benutzt, während als hydrophobe Blöcke B Poly(4-tert-butyl styrol), Polystyrol, Poly(3,5-dibromo benzyl acrylat), Poly(2-ethylhexyl acrylat), und Poly(octadecyl acrylat) als Bausteine mit unterschiedlicher Glasübergangstemperatur untersucht wurden. Die Selbstorganisation von ABA und BAB Copolymeren in Wasser mit A Blöcken aus PNIPAM wurde anhand von Trübungsphotometrie, dynamischer Lichtstreuung (DLS) und Rheologie untersucht. Die amphiphilen Blockcopolymere sind direkt wasserlöslich. Bei Konzentrationen von 0.01 bis 50 wt% zeigen Trübungsmessungen bei den Blockcopolymeren wie bei den Homopolymeren eine Übergangstemperatur bei 28-32 °C. Zurückzuführen ist dies auf die Bildung von Mizellen, bei der die hydrophoben Blöcke von einem direkten Kontakt mit Wasser abgeschirmt werden. DLS zeigt kleine Mizellen bei niedrigen Temperaturen und Aggregate mit großem hydrodynamischem Durchmesser bei Temperaturen oberhalb der Übergangstemperatur. Die rheologische Untersuchung von BAB Polymeren zeigt die Bildung von Hydrogelen bei höheren Konzentrationen (über 30-35 wt%). Die minimal benötigte Konzentration, bei der die von Hydrogelen auftreten, nimmt mit wachsender Glasübergangstemperatur ab, und nimmt mit der Länge der hydrophoben Blöcke B zu. Im Unterschied zu PNIPAM zeigen wässrige Lösungen von PMDEGA und seinen Blockcopolymeren reversible Übergangstemperaturen abhängig von der chemischen Struktur. Außerdem bilden PMDEGA Blockcopolymere Hydrogele bei niedriger Konzentration (ab 20 wt%). Dieses Ergebnis deutet darauf hin, dass PMDEGA stärker Wasser bindet als PNIPAM. KW - Design KW - Synthese KW - Charakterisierung KW - Triblock-Copolymere KW - RAFT KW - Design KW - Synthesis KW - Characterisation KW - Triblock Copolymers KW - RAFT Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-39549 ER - TY - THES A1 - Ishebabi, Harold T1 - Architecture synthesis for adaptive multiprocessor systems on chip T1 - Architektursynthese adaptiver On-Chip Multiprozessor-Systeme N2 - This thesis presents methods for automated synthesis of flexible chip multiprocessor systems from parallel programs targeted at FPGAs to exploit both task-level parallelism and architecture customization. Automated synthesis is necessitated by the complexity of the design space. A detailed description of the design space is provided in order to determine which parameters should be modeled to facilitate automated synthesis by optimizing a cost function, the emphasis being placed on inclusive modeling of parameters from application, architectural and physical subspaces, as well as their joint coverage in order to avoid pre-constraining the design space. Given a parallel program and a set of an IP library, the automated synthesis problem is to simultaneously (i) select processors (ii) map and schedule tasks to them, and (iii) select one or several networks for inter-task communications such that design constraints and optimization objectives are met. The research objective in this thesis is to find a suitable model for automated synthesis, and to evaluate methods of using the model for architectural optimizations. Our contributions are a holistic approach for the design of such systems, corresponding models to facilitate automated synthesis, evaluation of optimization methods using state of the art integer linear and answer set programming, as well as the development of synthesis heuristics to solve runtime challenges. N2 - Aktuelle Technologien erlauben es komplexe Multiprozessorsysteme auf einem Chip mit Milliarden von Transistoren zu realisieren. Der Entwurf solcher Systeme ist jedoch zeitaufwendig und schwierig. Diese Arbeit befasst sich mit der Frage, wie On-Chip Multiprozessorsysteme ausgehend von parallelen Programmen automatisch synthetisiert werden können. Die Implementierung der Multiprozessorsysteme auf rekonfigurierbaren Chips erlaubt es die gesamte Architektur an die Struktur eines vorliegenden parallelen Programms anzupassen. Auf diese Weise ist es möglich die aktuellen technologischen Unzulänglichkeiten zu umgehen, insbesondere die nicht weitersteigende Taktfrequenzen sowie den langsamen Zugriff auf Datenspeicher. Eine Automatisierung des Entwurfs von Multiprozessorsystemen ist notwendig, da der Entwurfsraum von Multiprozessorsystemen zu groß ist, um vom Menschen überschaut zu werden. In einem ersten Ansatz wurde das Syntheseproblem mittels linearer Gleichungen modelliert, die dann durch lineare Programmierungswerkzeuge gelöst werden können. Ausgehend von diesem Ansatz wurde untersucht, wie die typischerweise langen Rechenzeiten solcher Optimierungsmethoden durch neuere Methode aus dem Gebiet der Erfüllbarkeitsprobleme der Aussagenlogik minimiert werden können. Dabei wurde die Werkzeugskette Potassco verwendet, in der lineare Programme direkt in Logikprogramme übersetzt werden können. Es wurde gezeigt, dass dieser zweite Ansatz die Optimierungszeit um bis zu drei Größenordnungen beschleunigt. Allerdings lassen sich große Syntheseprobleme auf diese weise wegen Speicherbegrenzungen nicht lösen. Ein weiterer Ansatz zur schnellen automatischen Synthese bietet die Verwendung von Heuristiken. Es wurden im Rahmen diese Arbeit drei Heuristiken entwickelt, die die Struktur des vorliegenden Syntheseproblems ausnutzen, um die Optimierungszeit zu minimieren. Diese Heuristiken wurden unter Berücksichtigung theoretischer Ergebnisse entwickelt, deren Ursprung in der mathematische Struktur des Syntheseproblems liegt. Dadurch lassen sich optimale Architekturen in kurzer Zeit ermitteln. Die durch diese Dissertation offen gewordene Forschungsarbeiten sind u. a. die Berücksichtigung der zeitlichen Reihenfolge des Datenaustauschs zwischen parallelen Tasks, die Optimierung des logik-basierten Ansatzes, die Integration von Prozessor- und Netzwerksimulatoren zur funktionalen Verifikation synthetisierter Architekturen, sowie die Entwicklung geeigneter Architekturkomponenten. KW - Multiprozessor KW - rekonfigurierbar KW - Synthese KW - Parallelrechner KW - Exploration KW - Multiprocessor KW - Reconfigurable KW - High-Level Synthesis KW - Parallel Programming KW - Exploration Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-41316 ER - TY - THES A1 - Herfurth, Christoph T1 - Einstufen-Synthese und Charakterisierung amphiphiler Sternpolymere als multifunktionale assoziative Verdicker T1 - One-step synthesis and characterisation of amphiphilic star polymers as multifunctional associative thickeners N2 - Typische assoziative Verdicker für wässrige Systeme basieren auf linearen, doppelt hydrophob endmodifizierten Poly(ethylenglykolen) (PEGs). Diese Polymere aggregieren aufgrund ihrer Struktur in wässriger Lösung und bilden ein Netzwerk aus verbrückten Polymer-Mizellen. Dabei kann ein Polymer-Molekül maximal zwei Mizellen miteinander verbinden. Bisher ist unklar, wie die Anzahl der Endgruppen eines verzweigten, mehrfach hydrophob endmodifizierten hydrophilen Polymers die Struktur und Dynamik solcher Netzwerke beeinflusst. Die Synthese verzweigter Polymere auf PEG-Basis erfolgt mittels lebender ionischer Polymerisation und ist experimentell aufwändig. Das Einführen hydrophober Endgruppen erfordert zusätzliche Synthese-Schritte. In dieser Arbeit wurden hydrophile Sternpolymere mit hydrophoben Endgruppen in einem Schritt hergestellt. Dazu wurde die Technik der radikalischen Polymerisation unter Kettenübertragung durch reversible Addition und anschließende Fragmentierung (reversible addition-fragmentation chain transfer, RAFT) genutzt. Die Synthese der Sternpolymere erfolgte von einem multifunktionalen Kern, der die R-Gruppe der RAFT-Kettenüberträger (chain transfer agents, CTAs) bildete. Die dazu benötigten CTAs wurden so konzipiert, dass mit ihrer Hilfe sowohl die Anzahl der Arme des Sternpolymers (von 2 bis 4), als auch die Länge der hydrophoben Endgruppe (C4, C12, C18) variiert werden konnte. Der große Vorteil der RAFT-Polymerisation ist, dass sie viele polare Monomere für die Synthese der hydrophilen Arme des Sternpolymers toleriert. In dieser Arbeit wurden als Modell-Monomere Oligo(ethylenglykol)methylether-acrylat (OEGA) und N,N-Dimethylacrylamid (DMA) eingesetzt. Beide Monomere bilden nicht-ionische hydrophile Polymere. Poly(OEGA) ist ein Kammpolymer, das auf PEG basiert. Poly(DMA) besitzt dagegen eine deutlich kompaktere Struktur. Die erhaltenen amphiphilen Sternpolymere wurden umfassend molekular charakterisiert. Die Molmassen wurden mit verschiedenen GPC-Systemen bestimmt und der Grad der Endgruppenfunktionalisierung wurde mittels UV/Vis- und 1H-NMR-Spektroskopie überprüft. Die Polymerisation von OEGA zeigt mit den CTAs einige Charakteristika der Polymerisation mit reversibler Deaktivierung (RDRP, auch „kontrollierte radikalische Polymerisation“), wird aber durch Kettenübertragung zum Monomer bzw. Polymer gestört. Diese Nebenreaktion ist auf die Struktur des Monomers als Oligoether zurückzuführen. Bei allen untersuchten Polymerisationen von DMA mit den multifunktionalen CTAs steigt die Molmasse linear mit dem Umsatz. Die erhaltenen Polymere zeigen durchweg monomodale und enge Molmassenverteilungen (PDI ≤ 1,2). Die Molmassen lassen sich in einem weiten Bereich von 25 kg/mol bis 150 kg/mol einstellen und die Endgruppen der Polymere bleiben zu 90 % erhalten. Während die Polymerisation von DMA sowohl mit den di- als auch den trifunktionalen CTAs innerhalb von 3 h zu quantitativen Umsätzen verläuft, wird der quantitative Umsatz des Monomers bei der Polymerisation mit tetrafunktionalen CTAs erst nach 4 h erreicht. Diese Verzögerung ist auf eine Retardierung in der Anfangsphase der Polymerisation zurückzuführen, die sich aus der besonderen Struktur der tetrafunktionalen CTAs erklärt. Auf dem System zur Polymerisation von DMA aufbauend ließen sich Gradienten-Block-Copolymere in Eintopfreaktionen herstellen. Dazu wurde nach Erreichen des quantitativen Umsatzes von DMA ein zweites Monomer zur Reaktionsmischung gegeben. Mit Ethylacrylat (EtA) wurden so lineare amphiphile symmetrische Triblock-Copolymere erhalten. Dabei wurde die Länge des hydrophoben Blocks durch unterschiedliche Mengen an EtA variiert. Mit N,N-Diethylacrylamid (DEA) wurden lineare symmetrische Triblock-Copolymere sowie 3-Arm Stern-Diblock-Copolymere hergestellt, die über einen thermisch schaltbaren zweiten Block verfügen. Bei diesen Polymeren lässt sich die Länge des hydrophoben Teils in situ durch Veränderung der Temperatur variieren. Das Verhalten der amphiphilen Sternpolymere in wässriger Lösung und in Mikroemulsion wurde im Rahmen einer Kooperation an der TU Berlin mit Hilfe von Kleinwinkel-Neutronenstreuung (SANS), dynamischer Lichtstreuung (DLS) und Rheologie untersucht. Die Polymere wirken durch Assoziation der hydrophoben Endgruppen als effektive Verdicker sowohl allein in wässriger Lösung als auch in Mikroemulsion. Die Struktur des gebildeten Netzwerks hängt dabei von der Konzentration des Polymers in der Lösung und der Länge der Endgruppe (Hydrophobie) ab. Die dynamischen Eigenschaften der Lösungen werden außerdem durch die Anzahl der Arme der Polymere bestimmt. N2 - Typically, associative thickeners for aqueous system consist of linear, hydrophobically α,ω-end-capped poly(ethylene glycols) (PEGs). Owing to their structure, these polymers aggregate in aqueous solution, forming a network of bridged micelles. Thus, one polymer molecule can link not more than two micelles. Until now it is unclear whether the structure and dynamics of such networks are influenced by the number of end groups of a branched multiply hydrophobically end-capped hydrophilic polymers. Branched PEG-based polymers are synthesized using the laborious and limited techniques of living ionic polymerization. Introducing hydrophobic end groups demands a multiple-step process. This work presents the one-step synthesis of hydrophilic star polymers with hydrophobic end groups, using reversible addition fragmentation chain transfer (RAFT) polymerization. This radical polymerization method is easy to use and tolerates a large number of polar monomers for the synthesis of the hydrophilic arms of the star polymers. The arms of the polymer were grown from a multifunctional core that formed the R-group of the chain transfer agents (CTAs). The CTAs where tailored to be able to vary the number of arms of the star polymers from 2 to 4 and to vary the length (and therefore the hydrophobicity) of the end groups (C4, C12, C18). Two different polar monomers where used as model monomers: Oligo(ethylene glycol)methyl ether acrylate (OEGA) and N,N-Dimethylacrylamide (DMA). Both monomers yield non-ionic hydrophilic polymers. While poly(OEGA) is a comb polymer based on PEG, poly(DMA) exhibits a more compact structure. The amphiphilic star polymers were characterized extensively. The molar masses were determined using GPC in various solvents and the degree of end functionalisation was monitored using 1H NMR and UV/Vis spectroscopy. The polymerization of OEGA shows some of the expected characteristics of reversible deactivation radical polymerization (RDRP). However, chain transfer to monomer and polymer is a prominent side reaction, limiting the use of this monomer for the fabrication of well-defined material. This reaction can be attributed to the structure of the monomer being an oligoether. For all examined polymerizations of DMA with the multifunctional CTAs the molar mass increased linearly with conversion. The molar mass distributions were monomodal and narrow (PDI ≤ 1.2). Expected values were reached for molar masses from 25 to 150 kg/mol and the end group functionality was about 90 % in all cases. While the polymerization of DMA using di- and trifunctional CTAs proceeded to quantitative conversion within 3 h, an initial retardation period of about 60 min was observed for the polymerization using tetrafunctional CTAs. This retardation was attributed to the peculiar molecular structure of these CTAs. Owing to the well-controlled features of the polymerization of DMA using the multifunctional CTAs, this system was used to obtain tapered block copolymers in a one-pot process. These structures were achieved by adding a second monomer to the reaction mixture after the quantitative conversion of DMA. Using ethyl acrylate (EtA), linear amphiphilic symmetrical triblock copolymers were synthesized. The length of the hydrophobic block was tailored by the addition of varying amounts of EtA. With N,N-Diethylacrylamide as a second monomer, linear symmetric triblock copolymers as well as 3-arm star diblock copolymers were obtained that contain a thermosensitve block. Altering the temperature of aqueous solutions of these polymers varies the length of the hydrophobic block in situ. At the TU Berlin, the behavior of the polymers was studied in aqueous solution as well as in microemulsion. The solutions were characterized by small angle neutron scattering (SANS), dynamic light scattering (DLS) and rheology. The end groups of the polymers aggregate, making the polymers efficient thickeners both in aqueous solution and in microemulsion. The structure of the formed network depends on the concentration of the polymer in solution and on the length of the end group. The dynamic properties of the solutions are governed additionally by the number of arms. KW - RAFT-Polymerisation KW - Sternpolymere KW - Synthese KW - Amphiphile Polymere KW - Assoziative Verdicker KW - RAFT polymerisation KW - star polymers KW - synthesis KW - amphiphilic polymers KW - associative thickeners Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-62446 ER - TY - THES A1 - Steeples, Elliot T1 - Amino acid-derived imidazolium salts: platform molecules for N-Heterocyclic carbene metal complexes and organosilica materials T1 - Imidazolium-Salze aus Aminosäure: Bausteine für N-Heterozyklische-Carben Metallkomplexe und Organosilicamaterialien N2 - In the interest of producing functional catalysts from sustainable building-blocks, 1, 3-dicarboxylate imidazolium salts derived from amino acids were successfully modified to be suitable as N-Heterocyclic carbene (NHC) ligands within metal complexes. Complexes of Ag(I), Pd(II), and Ir(I) were successfully produced using known procedures using ligands derived from glycine, alanine, β-alanine and phenylalanine. The complexes were characterized in solid state using X-Ray crystallography, which allowed for the steric and electronic comparison of these ligands to well-known NHC ligands within analogous metal complexes. The palladium complexes were tested as catalysts for aqueous-phase Suzuki-Miyaura cross-coupling. Water-solubility could be induced via ester hydrolysis of the N-bound groups in the presence of base. The mono-NHC–Pd complexes were seen to be highly active in the coupling of aryl bromides with phenylboronic acid; the active catalyst of which was determined to be mostly Pd(0) nanoparticles. Kinetic studies determined that reaction proceeds quickly in the coupling of bromoacetophenone, for both pre-hydrolyzed and in-situ hydrolysis catalyst dissolution. The catalyst could also be recycled for an extra run by simply re-using the aqueous layer. The imidazolium salts were also used to produce organosilica hybrid materials. This was attempted via two methods: by post-grafting onto a commercial organosilica, and co-condensation of the corresponding organosilane. The co-condensation technique harbours potential for the production of solid-support catalysts. N2 - Um Katalysatoren aus nachhaltigen Chemikalien herzustellen, wurden 1,3-Dicarbonsäure-Imidazolium-Salze, welche aus Aminosäuren synthetisiert wurden als N-heterozyklische-Carben-Liganden (NHC) in Metallkomplexen modifiziert. Liganden aus Glycin, Alanin, β-Alanin und Phenylalanin wurden wiederum genutzt, um Metallkomplexe aus Silber(I), Palladium(II) und Iridium(I) darzustellen. Alle Komplexverbindungen wurden mit Röntgenkristallographie charakterisiert. Die Palladiumkomplexe wurden als Katalysatoren in der Suzuki-Miyaura Reaktion eingesetzt. Durch zusätzliche Hydrolyse der Ester-Gruppen konnte eine gute Wasserlöslichkeit erreicht werden. Die hohe Aktivität der Mono-NHC–Palladium-Komplexe konnte bei der Kupplung von Arylbromiden mit Phenylboronsäuren aufgezeigt werden. Die aktive Spezies wurde hauptsächlich Pd(0) Nanopartikeln zugeschrieben. Nach erfolgreichem Recycling konnte der Katalysator noch einmal wiederverwendet werden. Die Imidazolium-Salze wurden ebenfalls herangezogen, um Organosilicamaterialien zu synthetisieren. Die Herstellung wurde durch zwei Methoden erreicht. Zum einen durch nachträgliches Aufbringen auf kommerzielle Siliziummaterialien, sowie durch Co-Kondensation auf das entsprechende Organosilan. Diese Co-Kondensation birgt Potential zur Herstellung von festen Trägerkatalysatoren. KW - synthesis KW - Synthese KW - sustainable chemistry KW - nachhaltige Chemie KW - organometallics KW - Metallorganischen KW - water KW - Wasser Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-101861 ER - TY - THES A1 - Lood, Kajsa T1 - Stereoselective Construction of C-C Double Bonds via Olefin Metathesis: From Tethered Reactions to Water-Soluble Catalysts for Stereoretentive Metathesis T1 - Stereoselektiver Aufbau von C-C-Doppelbindungen durch Olefinmetathese: Von gebundenen Reaktionen zu wasserlöslichen Katalysatoren für die stereoretentive Metathese N2 - Natural products have proved to be a major resource in the discovery and development of many pharmaceuticals that are in use today. There is a wide variety of biologically active natural products that contain conjugated polyenes or benzofuran structures. Therefore, new synthetic methods for the construction of such building blocks are of great interest to synthetic chemists. The recently developed one-pot tethered ring-closing metathesis approach allows for the formation of Z,E-dienoates in high stereoselectivity. The extension of this method with a Julia-Kocienski olefination protocol would allow for the formation of conjugated trienes in a stereoselective manner. This strategy was applied in the total synthesis of conjugated triene containing (+)-bretonin B. Additionally, investigations of cross metathesis using methyl substituted olefins were pursued. This methodology was applied, as a one-pot cross metathesis/ring-closing metathesis sequence, in the total synthesis of benzofuran containing 7-methoxywutaifuranal. Finally, the design and synthesis of a catalyst for stereoretentive metathesis in aqueous media was investigated. N2 - Naturstoffe haben sich als wichtige Ressource für die Entdeckung und Entwicklung zahlreicher Arzneimittel erwiesen, die heute verwendet werden. Es gibt eine Vielzahl biologisch aktiver Naturstoffe, die konjugierte Polyene oder Benzofuranstrukturen enthalten. Daher sind neue Synthesemethoden für die Herstellung solcher Bausteine für synthetische Chemiker von großem Interesse. Der kürzlich entwickelte Ein-Topf-Ansatz der tethered ring-closing metathesis ermöglicht die Bildung von Z,E-Dienoaten in hoher Stereoselektivität. Die Erweiterung dieser Methode mit einem Julia-Kocienski-Olefinierungsprotokoll würde die Bildung von konjugierten Trienen in stereoselektiver Weise ermöglichen. Diese Strategie wurde bei der Totalsynthese von konjugierten Trienen, die (+)-Bretonin B enthalten, angewandt. Außerdem wurden Untersuchungen zur Kreuzmetathese mit methylsubstituierten Olefinen durchgeführt. Diese Methodik wurde als Ein-Topf-Kreuzmetathese/Ringschluss-Metathese-Sequenz in der Totalsynthese von benzofuranhaltigem 7-Methoxywutaifuranal angewendet. Schließlich wurde die Entwicklung und Synthese eines Katalysators für die stereoretentive Metathese in wässrigen Medien untersucht. KW - Olefin metathesis KW - synthesis KW - organic chemistry KW - catalysts KW - Olefin Metathese KW - Synthese KW - organische Chemie KW - Katalysatoren Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-539142 ER - TY - THES A1 - Kwesiga, George T1 - Synthesis of isoflavonoids from African medicinal plants with activity against tropical infectious diseases T1 - Synthese von Isoflavonoiden aus afrikanischen Heilpflanzen mit Wirkung gegen tropische Infektionskrankheiten N2 - Two approaches for the synthesis of prenylated isoflavones were explored: the 2,3-oxidative rearrangement/cross metathesis approach, using hypervalent iodine reagents as oxidants and the Suzuki-Miyaura cross-coupling/cross metathesis approach. Three natural prenylated isoflavones: 5-deoxy-3′-prenylbiochanin A (59), erysubin F (61) and 7-methoxyebenosin (64), and non-natural analogues: 7,4′-dimethoxy-8,3′-diprenylisoflavone (126j) and 4′-hydroxy-7-methoxy-8,3′-diprenylisoflavone (128) were synthesized for the first time via the 2,3-oxidative rearrangement/cross metathesis approach, using mono- or diallylated flavanones as key intermediates. The reaction of flavanones with hypervalent iodine reagents afforded isoflavones via a 2,3-oxidative rearrangement and the corresponding flavone isomers via a 2,3-dehydrogenation. This afforded the synthesis of 7,4′-dimethoxy-8-prenylflavone (127g), 7,4′-dimethoxy-8,3′-diprenylflavone (127j), 7,4′-dihydroxy-8,3′-diprenylflavone (129) and 4′-hydroxy-7-methoxy-8,3′-diprenylflavone (130), the non-natural regioisomers of 7-methoxyebenosin, 126j, erysubin F and 128 respectively. Three natural prenylated isoflavones: 3′-prenylbiochanin A (58), neobavaisoflavone (66) and 7-methoxyneobavaisoflavone (137) were synthesized for the first time using the Suzuki-Miyaura cross-coupling/cross metathesis approach. The structures of 3′-prenylbiochanin A (58) and 5-deoxy-3′-prenylbiochanin A (59) were confirmed by single crystal X-ray diffraction analysis. The 2,3-oxidative rearrangement approach appears to be limited to the substitution pattern on both rings A and B of the flavanone while the Suzuki-Miyaura cross-coupling approach appears to be the most suitable for the synthesis of simple isoflavones or prenylated isoflavones whose prenyl substituents or allyl groups, the substituents that are essential precursors for the prenyl side chains, can be regioselectively introduced after the construction of the isoflavone core. The chalcone-flavanone hybrids 146, 147 and 148, hybrids of the naturally occurring bioactive flavanones liquiritigenin-7-methyl ether, liquiritigenin and liquiritigenin-4′-methyl ether respectively were also synthesized for the first time, using Matsuda-Heck arylation and allylic/benzylic oxidation as key steps. The intermolecular interactions of 5-deoxy-3′-prenylbiochanin A (59) and its two closely related precursors 106a and 106b was investigated by single crystal and Hirshfeld surface analyses to comprehend their different physicochemical properties. The results indicate that the presence of strong intermolecular O-H···O hydrogen bonds and an increase in the number of π-stacking interactions increases the melting point and lowers the solubility of isoflavone derivatives. However, the strong intermolecular O-H···O hydrogen bonds have a greater effect than the π-stacking interactions. 5-Deoxy-3′-prenylbiochanin A (59), erysubin F (61) and 7,4′-dihydroxy-8,3′-diprenylflavone (129), were tested against three bacterial strains and one fungal pathogen. All the three compounds were inactive against Salmonella enterica subsp. enterica (NCTC 13349), Escherichia coli (ATCC 25922), and Candida albicans (ATCC 90028), with MIC values greater than 80.0 μM. The diprenylated isoflavone erysubin F (61) and its flavone isomer 129 showed in vitro activity against methicillin-resistant Staphylococcus aureus (MRSA, ATCC 43300) at MIC values of 15.4 and 20.5 μM, respectively. 5-Deoxy-3′-prenylbiochanin A (59) was inactive against this MRSA strain. Erysubin F (61) and its flavone isomer 129 could serve as lead compounds for the development of new alternative drugs for the treatment of MRSA infections. N2 - Ziel dieser Studie war es, aus afrikanischen Heilpflanzen isolierte Naturstoffe künstlich herzustellen, die zur Behandlung tropischer Infektionskrankheiten wie Malaria und bakterieller Infektionen eingesetzt werden, um Schlüsselsubstanzen für die Entwicklung neuer Medikamente zu identifizieren. Sechs Naturstoffe aus afrikanischen Heilpflanzen wie dem Korallenbaum (Erythrina-species) wurden erstmals künstlich hergestellt. Bei der Herstellung dieser Naturstoffe wurden auch sechs weitere verwandte nicht-natürliche Analoga hergestellt. Zwei Naturstoffe (5-Deoxy-3′-prenylbiochanin A und Erysubin F) aus dem Korallenbaum (Erythrina sacleuxii) und eine verwandte nicht-natürliche Substanz wurden auf ihre antimikrobielle Aktivität gegen drei Bakterienstämme und einen Pilzstamm getestet. Alle drei Substanzen waren nicht wirksam gegen Escherichia coli, ein Bakterium, das Harnwegsinfektionen und Durchfall verursacht; Salmonella entrica, das Typhus verursacht, und Candida albicans, das Candidiasis verursacht. Erysubin F und sein nicht-natürliches Analogon waren sehr aktiv gegen Methicillin-resistente Staphylococcus aureus (MRSA), ein Bakterium, das hauptsächlich in sehr geringen Konzentrationen Hautinfektionen verursacht. 5-Deoxy-3'-prenylbiochanin A war gegen diesen MRSA-Stamm nicht aktiv. Erysubin F und sein nicht-natürliches Analogon könnten als Schlüsselsubstanzen für die Entwicklung eines neuen Medikaments gegen Infektionen durch MRSA dienen. KW - synthesis KW - isoflavonoids KW - African medicinal plants KW - tropical infectious diseases KW - Afrikanische Heilpflanzen KW - Isoflavonoide KW - Synthese KW - tropische Infektionskrankheiten Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-559069 ER - TY - THES A1 - Kemper, Tarek T1 - KLIMAGRAR – Neue Methoden der Begleitforschung am Beispiel des klimagerechten Handelns in der Landwirtschaft N2 - In Forschungsprogrammen werden zahlreiche Akteure mit unterschiedlichen Hintergründen und fachlichen Expertisen in Einzel- oder Verbundvorhaben vereint, die jedoch weitestgehend unabhängig voneinander durchgeführt werden. Vor dem Hintergrund, dass gesamtgesellschaftliche Herausforderungen wie die globale Erwärmung zunehmend disziplinübergreifende Lösungsansätze erfordern, sollten Vernetzungs- und Transferprozesse in Forschungsprogrammen stärker in den Fokus rücken. Mit der Implementierung einer Begleitforschung kann dieser Forderung Rechnung getragen werden. Begleitforschung unterscheidet sich in ihrer Herangehensweise und ihrer Zielvorstellung von den „üblichen“ Projekten und kann in unterschiedlichen theoretischen Reinformen auftreten. Verkürzt dargestellt agiert sie entweder (1) inhaltlich komplementär zu den jeweiligen Forschungsprojekten, (2) auf einer Metaebene mit Fokus auf die Prozesse im Forschungsprogramm oder (3) als integrierende, synthetisierende Instanz, für die die Vernetzung der Projekte im Forschungsprogramm sowie der Wissenstransfer von Bedeutung sind. Zwar sind diese Formen analytisch in theoretische Reinformen trennbar, in der Praxis ergibt sich in der Regel jedoch ein Mix aus allen dreien. In diesem Zusammenhang schließt die vorliegende Dissertation als ergänzende Studie an bisherige Ansätze zum methodischen Handwerkszeug der Begleitforschung an und fokussiert auf folgende Fragestellungen: Auf welcher Basis kann die Vernetzung der Akteure in einem Forschungsprogramm durchgeführt werden, um diese effektiv zusammenzubringen? Welche weiteren methodischen Elemente sollten daran ansetzen, um einen Mehrwert zu generieren, der die Summe der Einzelergebnisse des Forschungsprogrammes übersteigt? Von welcher Art kann dann ein solcher Mehrwert sein und welche Rolle spielt dabei die Begleitforschung? Das erste methodische Element bildet die Erhebung und Aufbereitung einer Ausgangsdatenbasis. Durch eine auf semantischer Analyse basierenden Verschlagwortung projektbezogener Texte lässt sich eine umfassende Datenbasis aus den Inhalten der Forschungsprojekte generieren. Die Schlagwörter werden dabei anhand eines kontrollierten Vokabulars in einem Schlagwortkatalog strukturiert. Parallel dazu werden sie wiederum den jeweiligen Projekten zugeordnet, wodurch diese thematische Merkmale erhalten. Um thematische Überschneidungen zwischen Forschungsprojekten sichtbar und interpretierbar zu machen, beinhaltet das zweite Element Ansätze zur Visualisierung. Dazu werden die Informationen in einen Netzwerkgraphen transferiert, der sowohl alle im Forschungsprogramm involvierten Projekte als auch die identifizierten Schlagwörter in Relation zueinander abbilden kann. So kann zum Beispiel sichtbar gemacht werden, welche Forschungsprojekte sich auf Basis ihrer Inhalte „näher“ sind als andere. Genau diese Information wird im dritten methodischen Element als Planungsgrundlage für unterschiedliche Veranstaltungsformate wie Arbeitstagungen oder Transferwerkstätten genutzt. Das vierte methodische Element umfasst die Synthesebildung. Diese gestaltet sich als Prozess über den gesamten Zeitraum der Zusammenarbeit zwischen Begleitforschung und den weiteren Forschungsprojekten hinweg, da in die Synthese unter anderem Zwischen-, Teil- und Endergebnisse der Projekte einfließen, genauso wie Inhalte aus den unterschiedlichen Veranstaltungen. Letztendlich ist dieses vierte Element auch das Mittel, um aus den integrierten und synthetisierten Informationen Handlungsempfehlungen für zukünftige Vorhaben abzuleiten. Die Erarbeitung der methodischen Elemente erfolgte im laufenden Prozess des Begleitforschungsprojektes KlimAgrar, welches der vorliegenden Dissertation als Fallbeispiel dient und dessen Hintergründe in der Thematik Klimaschutz und Klimaanpassung in der Landwirtschaft im Text ausführlich erläutert werden. N2 - Research programs combine numerous actors with diverse backgrounds and scientific expertise in single or joint projects that are to a considerable extent conducted independently and remain largely unrelated. At a time when societal challenges such as global warming require interdisciplinary collaboration and solution-oriented approaches, research programs should strengthen networking and transfer processes. Implementing a project doing accompanying research that has a different set of tasks compared to usual research projects can help address this demand. The work of such a project can be shaped in three theoretical forms: (1) to complement the research projects by filling in content-related gaps, (2) to investigate and assess the ongoing processes within the research program compiling insights for future research design, or (3) to enhance synergies within the community supporting the cooperation between research projects. De facto, hybrid forms of these approaches are used. In this context, the present doctoral thesis is set to enhance the existing methodology of accompanying research focusing on the following research questions: on what basis could the networking process be conducted most effectively? Which additional methodological elements should follow this networking process to reach an additional value that exceeds the sum of single project results? How could this additional value look and what role does the accompanying research project play? The first methodological element comprises the acquisition and processing of the initial data base. A ‘keywording’ process using semantic analysis of project-related texts provides an enormous amount of ‘index terms’ (keywords) that build the basis for networking approaches within this community. To organize these key data, a structured knowledge organization process has been implemented. This type of systematic or ‘controlled’ approach provides a structured subject catalogue. At the same time, these keywords were reassigned to the respective research projects as content-related attributes. Visualizing thematic overlaps between research projects is the essence of the second methodological element. Transferring this information into a network graph allows visualizing all research projects and identified keywords in relation to each other. Such a network graph demonstrates the closeness between research projects based on their topics and reveals thematic clusters that are suitable for joint workshops addressing stakeholders across different disciplines and fields. Based on this, element three comprises the organization and conduct of such workshops and other meeting formats focusing on, for example, transfer processes. The fourth methodological element is synthesis building. The synthesis process is conducted over the entire time of a research program and is used to integrate all kinds of partial, intermediate, or final results of the research projects as well as essential points derived from the different workshop formats. Eventually, this element is the means to frame recommendations with regard to future funding policy and research. This methodological approach has been elaborated during the ongoing processes of the accompanying research project KlimAgrar, which serves as case study in the present doctoral thesis. KlimAgrar’s thematic background in the field of climate action in agriculture is presented comprehensively in this thesis. T2 - KLIMAGRAR – A new methodological approach for accompanying research in the field of climate change mitigation and adaptation in agriculture KW - Begleitforschung KW - Verschlagwortung KW - Vernetzung KW - Landwirtschaft KW - Klimaschutz KW - Klimaanpassung KW - Synthese KW - accompanying research KW - agriculture KW - climate change adaptation KW - climate change mitigation KW - keywording KW - networking KW - synthesis Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-601924 ER - TY - THES A1 - Voroshnin, Vladimir T1 - Control over spin and electronic structure of MoS₂ monolayer via interactions with substrates T1 - Kontrolle der Spin- und elektronischen Strukturen von MoS₂-Monolagen durch Wechselwirkungen mit Substraten N2 - The molybdenum disulfide (MoS2) monolayer is a semiconductor with a direct bandgap while it is a robust and affordable material. It is a candidate for applications in optoelectronics and field-effect transistors. MoS2 features a strong spin-orbit coupling which makes its spin structure promising for acquiring the Kane-Mele topological concept with corresponding applications in spintronics and valleytronics. From the optical point of view, the MoS2 monolayer features two valleys in the regions of K and K' points. These valleys are differentiated by opposite spins and a related valley-selective circular dichroism. In this study we aim to manipulate the MoS2 monolayer spin structure in the vicinity of the K and K' points to explore the possibility of getting control over the optical and electronic properties. We focus on two different substrates to demonstrate two distinct routes: a gold substrate to introduce a Rashba effect and a graphene/cobalt substrate to introduce a magnetic proximity effect in MoS2. The Rashba effect is proportional to the out-of-plane projection of the electric field gradient. Such a strong change of the electric field occurs at the surfaces of a high atomic number materials and effectively influence conduction electrons as an in-plane magnetic field. A molybdenum and a sulfur are relatively light atoms, thus, similar to many other 2D materials, intrinsic Rashba effect in MoS2 monolayer is vanishing small. However, proximity of a high atomic number substrate may enhance Rashba effect in a 2D material as it was demonstrated for graphene previously. Another way to modify the spin structure is to apply an external magnetic field of high magnitude (several Tesla), and cause a Zeeman splitting, the conduction electrons. However, a similar effect can be reached via magnetic proximity which allows us to reduce external magnetic fields significantly or even to zero. The graphene on cobalt interface is ferromagnetic and stable for MoS2 monolayer synthesis. Cobalt is not the strongest magnet; therefore, stronger magnets may lead to more significant results. Nowadays most experimental studies on the dichalcogenides (MoS2 included) are performed on encapsulated heterostructures that are produced by mechanical exfoliation. While mechanical exfoliation (or scotch-tape method) allows to produce a huge variety of structures, the shape and the size of the samples as well as distance between layers in heterostructures are impossible to control reproducibly. In our study we used molecular beam epitaxy (MBE) methods to synthesise both MoS2/Au(111) and MoS2/graphene/Co systems. We chose to use MBE, as it is a scalable and reproducible approach, so later industry may adapt it and take over. We used graphene/cobalt instead of just a cobalt substrate because direct contact of MoS2\ monolayer and a metallic substrate may lead to photoluminescence (PL) quenching in the metallic substrate. Graphene and hexagonal boron nitride monolayer are considered building blocks of a new generation of electronics also commonly used as encapsulating materials for PL studies. Moreover graphene is proved to be a suitable substrate for the MBE growth of transitional metal dichalcogenides (TMDCs). In chapter 1, we start with an introduction to TMDCs. Then we focus on MoS2 monolayer state of the art research in the fields of application scenario; synthesis approaches; electronic, spin, and optical properties; and interactions with magnetic fields and magnetic materials. We briefly touch the basics of magnetism in solids and move on to discuss various magnetic exchange interactions and magnetic proximity effect. Then we describe MoS2 optical properties in more detail. We start from basic exciton physics and its manifestation in the MoS2 monolayer. We consider optical selection rules in the MoS2 monolayer and such properties as chirality, spin-valley locking, and coexistence of bright and dark excitons. Chapter 2 contains an overview of the employed surface science methods: angle-integrated, angle-resolved, and spin-resolved photoemission; low energy electron diffraction and scanning tunneling microscopy. In chapter 3, we describe MoS2 monolayer synthesis details for two substrates: gold monocrystal with (111) surface and graphene on cobalt thin film with Co(111) surface orientation. The synthesis descriptions are followed by a detailed characterisation of the obtained structures: fingerprints of MoS2 monolayer formation; MoS2 monolayer symmetry and its relation to the substrate below; characterisation of MoS2 monolayer coverage, domain distribution, sizes and shapes, and moire structures. In chapter~4, we start our discussion with MoS2/Au(111) electronic and spin structure. Combining density functional theory computations (DFT) and spin-resolved photoemission studies, we demonstrate that the MoS2 monolayer band structure features an in-plane Rashba spin splitting. This confirms the possibility of MoS2 monolayer spin structure manipulation via a substrate. Then we investigate the influence of a magnetic proximity in the MoS2/graphene/Co system on the MoS2 monolayer spin structure. We focus our investigation on MoS2 high symmetry points: G and K. First, using spin-resolved measurements, we confirm that electronic states are spin-split at the G point via a magnetic proximity effect. Second, combining spin-resolved measurements and DFT computations for MoS2 monolayer in the K point region, we demonstrate the appearance of a small in-plane spin polarisation in the valence band top and predict a full in-plane spin polarisation for the conduction band bottom. We move forward discussing how these findings are related to the MoS2 monolayer optical properties, in particular the possibility of dark exciton observation. Additionally, we speculate on the control of the MoS2 valley energy via magnetic proximity from cobalt. As graphene is spatially buffering the MoS2 monolayer from the Co thin film, we speculate on the role of graphene in the magnetic proximity transfer by replacing graphene with vacuum and other 2D materials in our computations. We finish our discussion by investigating the K-doped MoS2/graphene/Co system and the influence of this doping on the electronic and spin structure as well as on the magnetic proximity effect. In summary, using a scalable MBE approach we synthesised MoS2/Au(111) and MoS2/graphene/Co systems. We found a Rashba effect taking place in MoS2/Au(111) which proves that the MoS2 monolayer in-plane spin structure can be modified. In MoS2/graphene/Co the in-plane magnetic proximity effect indeed takes place which rises the possibility of fine tuning the MoS2 optical properties via manipulation of the the substrate magnetisation. N2 - Die Molybdändisulfid-Monolage MoS2 ist ein mechanisch und chemisch robuster Direktband-Halbleiter. Seine Valley-Eigenschaften versprechen spin- und valleybezogene spintronische, valleytronische und optoelektronische Anwendungen. Hier wurde die Möglichkeit untersucht, die elektronische und Spin-Struktur von MoS2 durch Wechselwirkung mit einem Substrat zu beeinflussen. Eine Kontrolle der elektronischen Struktur und der Spinstruktur ist unerlässlich, wenn man die optischen Eigenschaften kontrollieren will. Wir haben zwei Methoden angewandt, um die Spinentartung aufzuheben. Zum einen haben wir die MoS2-Monolage einem elektrischen Potentialgradienten ausgesetzt, zum anderen einem starken Magnetfeld in der Ebene, das durch einen magnetischen Proximity-Effekt erzeugt wurde. Zu diesem Zweck haben wir zwei Systeme hergestellt: eine MoS2-Monolage auf einem Gold-Einkristall und eine MoS2-Monolage auf Graphen auf einer dünnen Kobalt-Schicht. Wir modifizierten ein zuvor vorgeschlagenes Verfahren zur Synthese der MoS2-Monolage auf der Au(111)-Oberfläche und erzielten mit der MBE-Methode eine Bedeckung von ≈0,4 MoS2-Monolage. Die Bedeckung wies eine 10×10-Überstruktur auf und bestand aus gleichmäßig verteilten und ähnlich orientierten Domänen von ≈30 nm Größe. Die Kombination aus DFT-Simulationen und spinaufgelöster Photoemissionsspektroskopie bestätigte das Vorhandensein einer Rashba-ähnlichen Spinaufspaltung in der Ebene der MoS2-Valenzbandzustände in Bereichen mit k ⃗≠0, aus Symmetriegründen mit Ausnahme des K ̅-Punktes. Wir untersuchten die Möglichkeit, die Spinstruktur der MoS2-Monolage durch den magnetischen Proximity-Effekt zu manipulieren, einschließlich der Bereiche um Hochsymmetriepunkte. Die Regionen der K ̅ und (K') ̅ Punkte sind am interessantesten, da sich dort die direkte Bandlücke der MoS2-Monolage befindet. Eine energetische Verschiebung der Valenz- und Leitungsbandzustände relativ zueinander in diesen Bereichen sollte die Kontrolle über die Valley-Aufspaltung der MoS2-Monolage ermöglichen. Andererseits sollte eine Neigung der Spinrichtung dieser Zustände in Richtung der Spinrichtung in der Ebene die optischen Auswahlregeln drastisch ändern und ein dunkles Exziton aufhellen. Wir haben ein Kobalt-Dünnschichtsubstrat aufgrund seiner in der Ebene liegenden magnetischen Anisotropie als Testobjekt für den magnetischen Proximity-Effekt gewählt. Wir benutzten die CVD-Methode, um es zunächst mit Graphen zu beschichten, und dann die MBE-Methode, um eine ≈0,4 MoS2-Monolage auf dem Substrat herzustellen. Wir platzierten das Graphen zwischen der MoS2-Monolage und der Kobalt-Dünnschicht, um zu verhindern, dass die Exzitonen von MoS2 durch das metallische Substrat ausgelöscht werden. Für die Herstellung der MoS2-Monolage auf dem Graphen/Co-Substrat haben wir ein Verfahren modifiziert, das für die Herstellung von MoS2 auf einem Graphen/Ir-Substrat vorgeschlagen wurde. Die einschichtige MoS2-Bedeckung von ≈0,4 Atomlagen zeigt eine große Fläche kristalliner Domänen von mehr als 200 nm Größe. Vier MoS2-Einheitszellen entsprechen fünf Graphen-Einheitszellen. Dies lässt auf eine 5×5-Überstruktur schließen, was durch die LEED-Bilder bestätigt wird. Andererseits zeigt die STM-Abbildung mit atomarer Auflösung eine quasi-periodische Struktur mit mehreren Arten von Moiré-Mustern. Da das epitaktische Wachstum von MoS2 entlang der Graphen-Untergitter A und B gleich wahrscheinlich ist, weist die MoS2-Monolage eine gleiche Anzahl von um 180° gedrehten Domänen (Spiegeldomänen) auf. Wir bestätigten zunächst das Vorhandensein des magnetischen Proximity-Effekts, indem wir ≈20 meV Zeeman in-plane Spinaufspaltung von MoS2-Valenzbandzuständen im Bereich von Γ ̅ sowohl in DFT-Berechnungen als auch in spinaufgelösten Photoemissionsmessungen beobachteten. Im Bereich von K ̅ stimmen Berechnungen und Messungen in Bezug auf die Spinpolarisation der Valenzbandzustände von 15% überein. Im Gegensatz dazu deuten die DFT-Berechnungen für die Leitungsbandzustände auf eine 100%ige Spinpolarisierung der Zustände hin. Dieses Ergebnis impliziert die Aufhellung der dunklen Exzitonen der MoS2-Monolage. Im Falle der Magnetisierung von Kobalt senkrecht zur Ebene sagen DFT-Berechnungen eine Spinaufspaltung von ≈16 meV bei Γ ̅ und ≈8 meV bei K ̅ und (K') ̅ voraus. Um die Leitungsbandzustände von MoS2 zu untersuchen, haben wir MoS2/Graphen/Co mit Kaliumatomen dotiert. Das resultierende System zeichnet sich dadurch aus, dass Kaliumatome unter MoS2 interkaliert sind, was den Abstand zwischen der MoS2-Monolage und dem Kobaltfilm vergrößert. Spinaufgelöste Messungen zeigten keine in-plane Spinaufspaltung der MoS2-Valenzbandzustände im Bereich von Γ ̅ und der MoS2-Leitungsbandzustände im Bereich von K ̅. Da Graphen eine Pufferschicht zwischen der MoS2-Monolage und der Kobaltschicht bildet, um ein mögliches Exzitonen-Löschen zu verhindern, untersuchten wir die Rolle von Graphen für den magnetischen Proximity-Effekt. In unseren Berechnungen ersetzten wir Graphen durch eine Graphen-Doppelschicht, h-BN, Vakuum und eine Kupfer-Monolage und kamen zu dem Schluss, dass der Effekt stark vom Orbitalüberlapp abhängt. MoS2/h-BN/Co zeigen ähnliche Ergebnisse, während MoS2-Graphen-Doppelschicht/Co und MoS2/Vakuum/Co fast keinen magnetischen Proximity-Effekt aufweisen. Zusammenfassend haben wir mittels spektroskopischer Methoden und DFT-Berechnungen bewiesen, dass die Spinstruktur einer MoS2-Monolage durch Wechselwirkung mit einem Substrat manipuliert werden kann. Wir blicken daher mit Zuversicht auf zukünftige optische Untersuchungen zur optischen Kontrolle von MoS2 und Dichalcogeniden der Gruppe VI durch den magnetischen Proximity-Effekt. KW - MoS₂ KW - Au(111) KW - gold substrate KW - magnetic proximity effect KW - dark exciton KW - Molybdenum sulfide monolayer KW - graphene KW - spin structure KW - valence band structure KW - Cobalt thin film KW - ARPES KW - Angle- and spin-resolved photoemission spectroscopy KW - MBE KW - Molecular Beam Epitaxy KW - CVD KW - Chemical Vapour Deposition KW - synthesis KW - XPS KW - X-rays Photoemission Spectroscopy KW - LEED KW - Low Energy Electron Diffraction KW - MoS₂ KW - Molybdänsulfid Monolagen KW - Graphene KW - Au(111) KW - Goldsubstrat KW - magnetischer Näherungseffekt KW - dunkles Exziton KW - Spinstruktur KW - Leitungsbandstruktur KW - Kobalt-Dünnfilm KW - Photoelektronenspektroskopie KW - Molekularstrahlepitaxie KW - chemische Gasphasenabscheidung KW - Synthese KW - Beugung niederenergetischer Elektronen Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-590709 ER - TY - THES A1 - Martínez Guajardo, Alejandro T1 - New zwitterionic polymers for antifouling applications T1 - Neue zwitterionische Polymere für Antifouling-Anwendungen N2 - The remarkable antifouling properties of zwitterionic polymers in controlled environments are often counteracted by their delicate mechanical stability. In order to improve the mechanical stabilities of zwitterionic hydrogels, the effect of increased crosslinker densities was thus explored. In a first approach, terpolymers of zwitterionic monomer 3-[N -2(methacryloyloxy)ethyl-N,N-dimethyl]ammonio propane-1-sulfonate (SPE), hydrophobic monomer butyl methacrylate (BMA), and photo-crosslinker 2-(4-benzoylphenoxy)ethyl methacrylate (BPEMA) were synthesized. Thin hydrogel coatings of the copolymers were then produced and photo-crosslinked. Studies of the swollen hydrogel films showed that not only the mechanical stability but also, unexpectedly, the antifouling properties were improved by the presence of hydrophobic BMA units in the terpolymers. Based on the positive results shown by the amphiphilic terpolymers and in order to further test the impact that hydrophobicity has on both the antifouling properties of zwitterionic hydrogels and on their mechanical stability, a new amphiphilic zwitterionic methacrylic monomer, 3-((2-(methacryloyloxy)hexyl)dimethylammonio)propane-1-sulfonate (M1), was synthesized in good yields in a multistep synthesis. Homopolymers of M1 were obtained by free-radical polymerization. Similarly, terpolymers of M1, zwitterionic monomer SPE, and photo-crosslinker BPEMA were synthesized by free-radical copolymerization and thoroughly characterized, including its solubilities in selected solvents. Also, a new family of vinyl amide zwitterionic monomomers, namely 3-(dimethyl(2-(N -vinylacetamido)ethyl)ammonio)propane-1-sulfonate (M2), 4-(dimethyl(2-(N-vinylacetamido)ethyl)ammonio)butane-1-sulfonate (M3), and 3-(dimethyl(2-(N-vinylacetamido)ethyl)ammonio)propyl sulfate (M4), together with the new photo-crosslinker 4-benzoyl-N-vinylbenzamide (M5) that is well-suited for copolymerization with vinylamides, are introduced within the scope of the present work. The monomers are synthesized with good yields developing a multistep synthesis. Homopolymers of the new vinyl amide zwitterionic monomers are obtained by free-radical polymerization and thoroughly characterized. From the solubility tests, it is remarkable that the homopolymers produced are fully soluble in water, evidence of their high hydrophilicity. Copolymerization of the vinyl amide zwitterionic monomers, M2, M3, and M4 with the vinyl amide photo-crosslinker M5 proved to require very specific polymerization conditions. Nevertheless, copolymers were successfully obtained by free-radical copolymerization under appropriate conditions. Moreover, in an attempt to mitigate the intrinsic hydrophobicity introduced in the copolymers by the photo-crosslinkers, and based on the proven affinity of quaternized diallylamines to copolymerize with vinyl amides, a new quaternized diallylamine sulfobetaine photo-crosslinker 3-(diallyl(2-(4-benzoylphenoxy)ethyl)ammonio)propane-1-sulfonate (M6) is synthesized. However, despite a priori promising copolymerization suitability, copolymerization with the vinyl amide zwitterionic monomers could not be achieved. N2 - Die hervorragenden Antifouling-Eigenschaften zwitterionischer Polymere in kontrollierten Bedingungen werden häufig durch ihre geringe mechanische Stabilität beeinträchtigt. Um die mechanische Eigenschaften zwitterionischer Hydrogele zu verbessern, wurde daher der Effekt einer erhöhten Vernetzungsdichte untersucht. In einem ersten Ansatz wurden Terpolymere aus dem zwitterionischen Monomer 3-[N -2(Methacryloyloxy)ethyl-N,N-dimethyl]ammonio propan-1-sulfonat (SPE), dem hydrophoben Monomer Butylmethacrylat (BMA) und dem Photovernetzer 2-(4-Benzoylphenoxy)ethylmethacrylat (BPEMA) synthetisiert. Daraufhin wurden dünne Beschichtungen der Copolymere hergestellt und photovernetzt. Die Untersuchung der gequollenen Hydrogelfilme zeigte, dass nicht nur die mechanischen Eigenschaften, sondern überraschenderweise auch die Antifouling-Eigenschaften der Hydrogele durch den Einbau von hydrophoben BMA-Einheiten in die Terpolymere verbessert wurden. Aufgrund der positiven Ergebnisse der amphiphilen Terpolymere und um die Auswirkungen der Hydrophobie sowohl auf die Antifouling- als auch auf die mechanische Eigenschaften der zwitterionischen Hydrogele zu testen, wurde ein neues amphiphiles zwitterionisches Methacrylat, nämlich 3-((2-(Methacryloyloxy)hexyl)dimethylammonio)propan-1-sulfonat (M1), in guter Ausbeute synthetisiert. Homopolymere von M1 wurden durch radikalische Polymerisation erhalten. In ähnlicher Weise wurden Terpolymere aus M1, dem zwitterionischen Monomer SPE und dem Photovernetzer BPEMA durch radikalische Copolymerisation synthetisiert und gründlich charakterisiert, einschließlich ihrer Löslichkeiten in ausgewählten Lösungsmitteln. Außerdem wurde im Rahmen der vorliegenden Arbeit eine neue Familie von zwitterionischen Vinylamidmonomeren, nämlich 3-(Dimethyl(2-(N-vinylacetamido)ethyl)ammonio)propan-1-sulfonat (M2), 4-(Dimethyl(2-(N -vinylacetamido)ethyl)ammonio)butan-1-sulfonat (M3) und 3-(Dimethyl(2-(N -vinylacetamido)ethyl)ammonio)propylsulfat (M4), zusammen mit einem geeigneten Vinylamid-Photovernetzer, nämlich 4-Benzoyl-N -vinylbenzamide (M5) entwickelt. Die Monomere wurden in einer Mehrstufen-Synthese mit guten Ausbeuten synthetisiert. Homopolymere der neuen zwitterionischen Vinylamidmonomere wurden durch radikalische Polymerisation erhalten und eingehend charakterisiert. Die Löslichkeitstests zeigen, dass die hergestellten Homopolymere bemerkenswerterweise vollständig in reinem Wasser löslich sind, was ihre hohe Hydrophilie beweist. Die Copolymerisation der zwitterionischen Vinylamidmonomere M2, M3 und M4 mit dem Vinylamid-Photovernetzer M5 erwies sich als schwierig. Die Copolymere lassen sich dennoch unter sehr spezifische Bedingungen durch radikalische Copolymerisation herstellen. Des Weiteren, um die durch die Photovernetzer in die Copolymere eingebrachte inhärente Hydrophobie zu mindern und aufgrund ihrer nachgewiesenen Affinität zur Copolymerisation mit Vinylamiden, wurde ein neuer quaternisierter Diallylaminsulfobetain-Photovernetzer 3-(Diallyl(2-(4-benzoylphenoxy)ethyl)ammonio)propan-1-sulfonat (M6) synthetisiert. Trotz a priori vielversprechender Copolymerisationseignung konnte jedoch keine Copolymerisation mit den zwitterionischen Vinylamidmonomeren erreicht werden. KW - antifouling KW - Antifouling KW - copolymers KW - Copolymere KW - hydrogels KW - Hydrogele KW - zwitterions KW - Zwitterionen KW - synthesis KW - Synthese Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-626820 ER -