TY - THES A1 - Iqbal, Zafar T1 - Interface design and characterization for stable inorganic perovskite solar cells T1 - Grenzflächendesign und- charakterisierung für stabile anorganische Perowskit-Solarzellen BT - inorganic perovskite solar cells N2 - We live in an era driven by fossil fuels. The prevailing climate change suggests that we have to significantly reduce greenhouse gas emissions. The only way forward is to use renewable energy sources. Among those, solar energy is a clean, affordable, and sustainable source of energy. It has the potential to satisfy the world’s energy demand in the future. However, there is a need to develop new materials that can make solar energy usable. Photovoltaics (PV) are devices that convert photon energy into electrical energy. The most commonly used solar cells are based on crystalline silicon. However, the fabrication process for silicon solar cells is technologically difficult and costly. Solar cells based on lead halide perovskites (PSCs) have emerged as a new candidate for PV applications since 2009. To date, PSCs have achieved 26% power-conversion-efficiency (PCE) for its single junction, and 33.7% PCE for tandem junction devices. However, there is still room for improvement in overall performance. The main challenge for the commercialization of this technology is the stability of the solar cells under operational conditions. Inorganic perovskite CsPbI3 has attracted researchers’ interest due to its stability at elevated temperatures, however, inorganic perovskites also have associated challenges, e.g. phase stability, larger voltage loss compared to their organic-inorganic hybrid counterparts, and interface energy misalignment. The most efficient inorganic perovskite solar cell is stable for up to a few hundred hours while the most stable device in the field of inorganic PSCs reported so far is at 17% PCE. This suggests the need for improvement of the interfaces for enhanced open circuit voltage (VOC), and optimization of the energy alignment at the interfaces. This dissertation presents the study on interfaces between the perovskite layer and hole transport layer (HTL) for stable CsPbI3 solar cells. The first part of the thesis presents an investigation of the CsPbI3 film annealing environment and its subsequent effects on the perovskite/HTL interface dynamics. Thin films annealed in dry air were compared with thin films annealed in ambient air. Synchrotron-based hard X-ray spectroscopy (HAXPES) measurements reveal that annealing in ambient air does not have an adverse effect; instead, those samples undergo surface band bending. This surface band modification induces changes in interface charge dynamics and, consequently, an improvement in charge extraction at the interfaces. Further, transient surface photovoltage (tr-SPV) simulations show that air-annealed samples exhibit fewer trap states compared to samples annealed in dry air. Finally, by annealing the CsPbI3 films in ambient air, a PCE of 19.8% and Voc of 1.23 V were achieved for an n-i-p structured device. Interface engineering has emerged as a strategy to extract the charge and optimize the energy alignment in perovskite solar cells (PSCs). An interface with fewer trap states and energy band levels closer to the selective contact helps to attain improved efficiencies in PSCs. The second part of the thesis presents a design for the CsPbI3/HTM interface. In this work, an interface between CsPbI3 perovskite and its hole selective contact N2,N2,N2′,N2′,N7,N7,N7′,N7′-octakis(4-methoxyphenyl)-9,9′-spirobi[9H-fluorene]-2,2′,7,7′-tetramine(Spiro-OMeTAD), realized by trioctylphosphine oxide (TOPO), a dipole molecule is introduced. On top of a perovskite film well-passivated by n-octyl ammonium Iodide (OAI), it created an upward surface band-bending at the interface byTOPO that optimizes energy level alignment and enhances the extraction of holes from the perovskite layer to the hole transport material. Consequently, a Voc of 1.2 V and high-power conversion efficiency (PCE) of over 19% were achieved for inorganic CsPbI3 perovskite solar cells. In addition, the work also sheds light on the interfacial charge-selectivity and the long-term stability of CsPbI3 perovskite solar cells. The third part of the thesis extends the previous studies to polymeric poly(3-hexylthiophene-2,5-diyl) (P3HT) as HTL. The CsPbI3/P3HT interface is critical due to high non-radiative recombination. This work presents a CsPbI3/P3HT interface modified with a long-chain alkyl halide molecule, n-hexyl trimethyl ammonium bromide (HTAB). This molecule largely passivates the CsPbI3 perovskite surface and improves the charge extraction across the interface. Consequently, a Voc of over 1.00 V and 14.2% PCE were achieved for CsPbI3 with P3HT as HTM. Overall the results presented in this dissertation introduce and discuss methods to design and study the interfaces in CsPbI3-based solar cells. This study can pave the way for novel interface designs between CsPbI3 and HTM for charge extraction, efficiency and stability. N2 - Wir leben in einem Zeitalter, das von fossilen Brennstoffen geprägt ist. Der fortschreitende Klimawandel erfordert eine merkliche Reduktion der Treibhausgasemissionen. Der einzige Weg hin zu einer nachhaltigen Energiewirtschaft ist die Implementierung erneuerbarer Energiequellen. Solarenergie hat das Potential, den Energiebedarf der Welt langfristig auf saubere und kostengünstige Weise zu decken. Es müssen jedoch neue Materialien zur Marktreife entwickelt werden, die die Solarenergie nutzbar machen können. In der Photovoltaik (PV) wird Lichtenergie in elektrische Energie umwandelt, wobei die gängisten Solarzellen aus kristallinem Silizium bestehen. Die Herstellung von Silizium-Solarzellen ist jedoch technisch aufwending und kostspielig. Deshalb haben sich Solarzellen auf Basis von Bleihalogenid-Perowskiten (engl. perovskite solar cells, PSCs) seit 2009 als mögliche Alternative zur Siliziumtechnologie entwickelt. Bisweilen konnten Wirkungsgrade (engl. power conversion efficiency, PCE) von 26% in einem einzelnen Halbleiterübergang und von 33.7% in einem Tandemübergang erzielt werden. Diese Werte sind jedoch steigerbar und werden regelmäßig übertroffen. Die größte Herausfoderung für die Entwicklung dieser Technologie ist die Stabilität der Solarzellen unter Betriebsbedingungen. Der anorganische Perowskit CsPbI3 ist aufgrund seiner Stabilität bei hohen Temperaturen deshalb besonders interessant für die Forschung, obwohl das Material seine eigenen Herausforderungen birgt, wie zum Beispiel seine Phaseninstabilität, größere Leerlaufspannungsverluste im Vergleich zu seinen organisch-anorganisch-hybriden Analoga und Fehlaurichtung der Energiebänder an der Grenzfläche. Die Stabilität der effizientesten Solarzelle auf CsPbI3-Basis liegt bei einigen hundert Stunden, während die stabilste Solarzelle einen Wirkungsgrad von nunmehr 17% erzielt. Dies deutet auf die Notwendigkeit hin, die Grenzflächen zu den angrenzenden ladungsselektiven Kontakten zu verbessern – mit dem Ziel, die Leerlaufspannung (engl. open-circuit voltage, VOC) zu erhöhen und die Ausrichtung der Energiebänder an den Grenzflächen zu optimieren. Diese Dissertation befasst sich mit der Untersuchung der Grenzflächen zwischen der Perowskitschicht und der Lochtransportschicht (engl. hole transport layer, HTL) für stabile CsPbI3-Solarzellen. Im ersten Teil der Arbeit werden die Temperbedingungen für CsPbI3-Dünnfilme und ihre Auswirkungen auf die Ladungsträgerdynamik an der Perowskit/HTL-Grenzfläche untersucht. Dünnfilme, die in trockener Atmosphäre getempert wurden, wurden mit Dünnfilmen verglichen, die in Standardatmosphäre getempert wurden. Synchrotrongestützte Messungen der Photoelektronenspektroskopie mit harter Röntgenstrahlung (engl. hard X-ray photoelectron spectrpscopy, HAXPES) zeigen, dass das Tempern in Umgebungsluft keine nachteiligen Auswirkungen hat; stattdessen erfahren jene Proben eine Verbiegung der Energiebänder an der Oberfläche. Diese Modifikation der Oberflächenbänder führt zu Veränderungen in der Grenzflächenladungsdynamik und in der Folge zu einer Verbesserung der Ladungsträgerextraktion über die Grenzfläche. Darüber hinaus zeigen Simulationen der transienten Oberflächenphotospannung (engl. transient surface photovoltage, trSPV), dass luftgetemperte Proben im Vergleich zu trockengetemperten Proben weniger Fallenzustände aufweisen. Letztlich wurde durch das Tempern der CsPbI3-Filme in Umgebungsluft eine PCE von 19,8% und ein VOC von 1,23 V für eine Solarzelle in n-i-p-Architektur erreicht. Die Manipulation der Grenzflächen ist eine Strategie, um die Extraktion von Ladungsträgern und die Ausrichtung der Energiebänder in PSCs zu kontrollieren. Eine Grenzfläche mit geringerer Dichte an Fallenzuständen sowie der Fähigkeit, das Energiebandniveau näher an das des selektiven Kontakts zu verschieben, trägt zur Verbesserung des Wirkungsgrads von PSCs bei. Im zweiten Teil der Arbeit wird ein Design für die CsPbI3/HTM-Grenzfläche vorgeschlagen. Dabei wird das Dipolmolekül Trioctylphosphinoxid (TOPO) an der Grenzfläche zwischen CsPbI3-Perowskit und dem lochselektiven Kontakt N2, N2, N2′, N2′, N7, N7, N7′, N7′-octakis(4-Methoxyphenyl) -9,9′-Spirobi[9H-Fluoren] -2,2′,7,7′-Tetramin (spiro-OMeTAD) eingeführt. Auf einem mit n-Octylammoniumiodid (OAI) passivierten Perowskitfilm erzeugt TOPO eine nach oben gerichtete Oberflächenbandverkrümmung, die die Ausrichtung der Energieniveaus optimiert und die Extraktion von Löchern aus CsPbI3 in den HTL verbessert. Infolgedessen wurden in den hergestellten Solarzellen ein VOC von 1,2 V und eine PCE von über 19% erzielt. Darüber hinaus nimmt die Arbeit auch die Ladungsträgerselektivität an der Grenzfläche und die Langzeitstabilität von CsPbI3-Perowskit-Solarzellen in den Fokus. Der dritte Teil der Arbeit erweitert die bisherigen Untersuchungen auf das Polymer Poly-(3-hexylthiophen-2,5-diyl) (P3HT) als HTL. Die CsPbI3/P3HT-Grenzfläche ist aufgrund der hohen nicht-radiativen Rekombination kritisch. In dieser Arbeit wird eine CsPbI3/P3HT-Grenzfläche vorgestellt, die mit einem langkettigen Alkylhalogenidmolekül, n-Hexyltrimethylammoniumbromid (HTAB), modifiziert wurde. Dieses Molekül passiviert die CsPbI3-Perowskit-Oberfläche weitgehend und verbessert die Ladungsträgerextraktion an der Grenzfläche. Für CsPbI3 mit P3HT als HTM konnte ein VOC von über 1,00 V und 14,2% PCE erreicht werden. Insgesamt werden in dieser Dissertation Methoden zur Entwicklung und Untersuchung von Grenzflächen für Solarzellen auf CsPbI3-Basis vorgestellt und diskutiert. Diese Studie kann Wege für neuartiges Grenzflächendesign zwischen CsPbI3 und HTM im Hinblick auf Ladungsträgerextraktion, Effizienz und Stabilität eröffnen. KW - CsPbI3 KW - interfaces KW - perovskite solar cells KW - CsPbI3 KW - Grenzflächen KW - Perowskit-Solarzellen Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-618315 ER - TY - JOUR A1 - Fandrich, Artur A1 - Buller, Jens A1 - Schäfer, Daniel A1 - Wischerhoff, Erik A1 - Laschewsky, André A1 - Lisdat, Fred T1 - Electrochemical characterization of a responsive macromolecular interface on gold JF - Physica status solidi : A, Applications and materials science N2 - This study reports on the investigation of a thermoresponsive polymer as a thin film on electrodes and the influence of coupling a peptide and an antibody to the film. The utilized polymer from the class of poly(oligoethylene glycol)-methacrylate polymers (poly(OEGMA)) with carboxy functions containing side chains was synthesized and properly characterized in aqueous solutions. The dependence of the cloud point on the pH of the surrounding media is discussed. The responsive polymer was immobilized on gold electrodes as shown by electrochemical, quartz crystal microbalance (QCM), and atomic force microscopy (AFM) techniques. The temperature dependent behavior of the polymer covalently grafted to gold substrates is investigated using cyclic voltammetry (CV) in ferro-/ferricyanide solution. Significant changes in the slope of the temperature-dependence of the voltammetric peak current and the peak separation values clearly indicate the thermally induced conformational change on the surface. Finally, a biorecognition reaction between a short FLAG peptide (N-Asp-Tyr-Lys-Asp-Asp-Asp-Asp-Lys-C) covalently immobilized on the polymer interface and the corresponding IgG antibody was performed. The study shows that the responsiveness of the electrode is retained after peptide coupling and antibody binding, although the response is diminished. KW - biorecognition reactions KW - cyclic voltammetry KW - electrodes KW - gold KW - interfaces KW - responsive polymers Y1 - 2015 U6 - https://doi.org/10.1002/pssa.201431698 SN - 1862-6300 SN - 1862-6319 VL - 212 IS - 6 SP - 1359 EP - 1367 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Friberg, Stig E. A1 - Kovach, Ildiko A1 - Koetz, Joachim T1 - Equilibrium topology and partial inversion of Janus Drops - a numerical analysis JF - ChemPhysChem : a European journal of chemical physics and physical chemistry N2 - The equilibrium topology of an aqueous Janus emulsion of two oils, O1 and O2, with water, W, [(O1+O2)/W], is numerically evaluated with the following realistic interfacial tensions (): (O2/W)=5 mNm(-1), (O1/O2)=1 mNm(-1), and (O1/W) varies within the range 4-5 mNm(-1), which is the limiting range for stable Janus drop topology. The relative significance of the two independently pivotal factors for the topology is evaluated, that is, the local equilibrium at the line of contact between the three liquids and the volume fraction of the two dispersed liquids within the drop. The results reveal a dominant effect of the local equilibrium on the fraction of the O2 drop surface that is covered by O1. In contrast, for a constant volume of O2, the impact of the interfacial tension balance on the limit of the coverage is modest for an infinite volume of O1. Interestingly, when the O1 volume exceeds this value, an emulsion inversion occurs, and the O1 portion of the (O1+O2)/W topology becomes a continuous phase, generating a (W+O2)/O1 Janus configuration. KW - emulsion inversion KW - interfaces KW - janus emulsions KW - liquids KW - semiempirical calculations Y1 - 2013 U6 - https://doi.org/10.1002/cphc.201300635 SN - 1439-4235 SN - 1439-7641 VL - 14 IS - 16 SP - 3772 EP - 3776 PB - Wiley-VCH CY - Weinheim ER -