@phdthesis{Hildebrandt2023, author = {Hildebrandt, Jana}, title = {Studies on nanoplastics for the preparation of reference materials}, doi = {10.25932/publishup-61710}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-617102}, school = {Universit{\"a}t Potsdam}, pages = {xvi, 88}, year = {2023}, abstract = {The present work focuses on the preparation and characterisation of various nanoplastic reference material candidates. Nanoplastics are plastic particles in a size range of 1 - 1000 nm. The term has emerged in recent years as a distinction from the larger microplastic (1 - 1000 μm). Since the properties of the two plastic particles differ significantly due to their size, it is important to have nanoplastic reference material. This was produced for the polymer types polypropylene (PP) and polyethylene (PE) as well as poly(lactic acid) (PLA). A top-down method was used to produce the nanoplastic for the polyolefins PP and PE (Section 3.1). The material was crushed in acetone using an Ultra-Turrax disperser and then transferred to water. This process produces reproducible results when repeated, making it suitable for the production of a reference material candidate. The resulting dispersions were investigated using dynamic and electrophoretic light scattering. The dispersion of PP particles gave a mean hydrodynamic diameter Dh = 180.5±5.8 nm with a PDI = 0.08±0.02 and a zeta potential ζ = -43.0 ± 2.0 mV. For the PE particles, a diameter Dh = 344.5 ± 34.6 nm, with a PDI = 0.39 ± 0.04 and a zeta potential of ζ = -40.0 ± 4.2 mV was measured. This means that both dispersions are nanoplastics, as the particles are < 1000 nm. Furthermore, the starting material of these polyolefin particles was mixed with a gold salt and thereby the nanoplastic production was repeated in order to obtain nanoplastic particles doped with gold, which should simplify the detection of the particles. In addition to the top-down approach, a bottom-up method was chosen for the PLA (Section 3.2). Here, the polymer was first dissolved in THF and stabilised with a surfactant. Then water was added and THF evaporated, leaving an aqueous PLA dispersion. This experiment was also investigated using dynamic light scattering and, when repeated, yielded reproducible results, i. e. an average hydrodynamic diameter of Dh = 89.2 ± 3.0 nm. Since the mass concentration of PLA in the dispersion is known due to the production method, a Python notebook was tested for these samples to calculate the number and mass concentration of nano(plastic) particles using the MALS results. Similar to the plastic produced in Section 3.1, gold was also incorporated into the particle, which was achieved by adding a dispersion of gold clusters with a diameter of D = 1.15 nm in an ionic liquid (IL) in the production process. Here, the preparation of the gold clusters in the ionic liquid 1-ethyl-3-methylimidazolium dicyanamide ([Emim][DCA]) represented the first use of an IL both as a reducing agent for gold and as a solvent for the gold clusters. Two volumes of gold cluster dispersion were added during the PLA particle synthesis. The addition of the gold clusters leads to much larger particles. The nanoPLA with 0.8\% Au has a diameter of Dh = 198.0 ± 10.8 nm and the nanoPLA with 4.9\% Au has a diameter of Dh = 259.1 ± 23.7 nm. First investigations by TEM imaging show that the nanoPLA particles form hollow spheres when gold clusters are added. However, the mechanism leading to these structures remains unclear.}, language = {en} } @phdthesis{Wang2018, author = {Wang, Li}, title = {Reprogrammable, magnetically controlled polymer actuators}, school = {Universit{\"a}t Potsdam}, pages = {xxviii, 107}, year = {2018}, abstract = {Polymeric materials, which can perform reversible shape changes after programming, in response to a thermal or electrical stimulation, can serve as (soft) actuating components in devices like artificial muscles, photonics, robotics or sensors. Such polymeric actuators can be realized with hydrogels, liquid crystalline elastomers, electro-active polymers or shape-memory polymers by controlling with stumuli such as heat, light, electrostatic or magnetic field. If the application conditions do not allow the direct heating or electric stimulation of these smart devices, noncontact triggering will be required. Remotely controlled actuation have been reported for liquid crystalline elastomer composites or shape-memory polymer network composites, when a persistent external stress is applied during inductive heating in an alternating magnetic field. However such composites cannot meet the demands of applications requiring remotely controlled free-standing motions of the actuating components. The current thesis investigates, whether a reprogrammable remotely controlled soft actuator can be realized by magneto-sensitive multiphase shape-memory copolymer network composites containing magnetite nanoparticles as magneto-sensitive multivalent netpoints. A central hypothesis was that a magnetically controlled two-way (reversible bidirectional) shape-memory effect in such nanocomposites can be achieved without application of external stress (freestanding), when the required orientation of the crystallizable actuation domains (ADs) can be ensured by an internal skeleton like structure formed by a second crystallizable phase determing the samples´s geometry, while magneto-sensitive iron oxide nanoparticles covalently integrated in the ADs allow remote temperature control. The polymer matrix of these composites should exhibit a phase-segregated morphology mainly composed of cyrstallizable ADs, whereby a second set of higher melting crystallites can take a skeleton like, geometry determining function (geometry determining domains, GDs) after programming of the composite and in this way the orientation of the ADs is established and maintained during actuation. The working principle for the reversible bidirectional movements in the multiphase shape-memory polymer network composite is related to a melting-induced contraction (MIC) during inductive heating and the crystallization induced elongation (CIE) of the oriented ADs during cooling. Finally, the amount of multivalent magnetosensitive netpoints in such a material should be as low as possible to ensure an adequate overall elasticity of the nanocomposite and at the same time a complete melting of both ADs and GDs via inductive heating, which is mandatory for enabling reprogrammability. At first, surface decorated iron oxide nanoparticles were synthesized and investigated. The coprecipitation method was applied to synthesize magnetic nanoparticles (mNPs) based on magnetite with size of 12±3 nm and in a next step a ring-opening polymerization (ROP) was utilized for covalent surface modification of such mNPs with oligo(ϵ-caprolactone) (OCL) or oligo(ω-pentadecalactone) (OPDL) via the "grafting from" approach. A successful coating of mNPs with OCL and OPDL was confirmed by differential scanning calorimetry (DSC) experiments showing melting peaks at 52±1 °C for mNP-OCL and 89±1 °C for mNP-OPDL. It was further explored whether two-layered surface decorated mNPs, can be prepared via a second surface-initiated ROP of mNP-OCL or mNP-OPDL with ω-pentadecalactone or ϵ-caprolactone. The observation of two distinct melting transitions in DSC experiments as well as the increase in molecular weight of the detached coatings determined by GPC and 1H-NMR indicated a successful synthesis of the twolayered nanoparticles mNP-OCL-OPDL and mNP-OPDL-OCL. In contrast TEM micrographs revealed a reduction of the thickness of the polymeric coating on the nanoparticles after the second ROP, indicating that the applied synthesis and purification required further optimization. For evaluating the impact of the dispersion of mNPs within a polymer matrix on the resulting inductive heating capability of composites, plain mNPs as well as OCL coated magnetite nanoparticles (mNP-OCLs) were physically incorporated into crosslinked poly(ε-caprolactone) (PCL) networks. Inductive heating experiments were performed with both networks cPCL/mNP and cPCL/mNP-OCL in an alternating magnetic field (AMF) with a magnetic field strength of H = 30 kA·m-1. Here a bulk temperature of Tbulk = 74±2 °C was achieved for cPCL/mNP-OCL, which was almost 20 °C higher than the melting transition of the PCL-based polymer matrix. In contrast, the composite with plain mNPs could only reach a Tbulk of 48±2 °C, which is not sufficient for a complete melting of all PCL crystallites as required for actuation. The inductive heating capability of a multiphase copolymer nanocomposite network (designed as soft actuators) containing surface decorated mNPs as covalent netpoints was investigated. Such composite was synthesized from star-shaped OCL and OPDL precursors, as well as mNP-OCLs via reaction with HDI. The weight ratio of OPDL and OCL in the starting reaction mixture was 15/85 (wt\%/wt\%) and the amount of iron oxide in the nanocomposite was 4 wt\%. DSC experiments revealed two well separated melting and crystallization peaks confirming the required phase-segregated morphology in the nanocomposite NC-mNP-OCL. TEM images could illustrate a phase-segregated morphology of the polymer matrix on the microlevel with droplet shaped regions attributed to the OPDL domains dispersed in an OCL matrix. The TEM images could further demonstrate that the nanoparticulate netpoints in NC-mNP-OCL were almost homogeneously dispersed within the OCL domains. The tests of the inductive heating capability of the nanocomposites at a magnetic field strength of Hhigh = 11.2 kA·m-1 revealed a achievable plateau surface temperature of Tsurf = 57±1 °C for NC-mNP-OCL recorded by an infrared video camera. An effective heat generation constant (̅P) can be derived from a multi-scale model for the heat generation, which is proportional to the rate of heat generation per unit volume of the sample. NC-mNP-OCL with homogeneously dispersed mNP-OCLs exhibited a ̅P value of 1.04±0.01 K·s- 1 at Hhigh, while at Hreset = 30.0 kA·m-1 a Tsurf of 88±1 °C (where all OPDL related crystallite are molten) and a ̅P value of 1.93±0.02 K·s-1 was obtained indicating a high magnetic heating capability of the composite. The free-standing magnetically-controlled reversible shape-memory effect (mrSME) was explored with originally straight nanocomposite samples programmed by bending to an angle of 180°. By switching the magnetic field on and off the composite sample was allowed to repetitively heat to 60 °C and cool to the ambient temperature. A pronounced mrSME, characterized by changes in bending angle of Δϐrev = 20±3° could be obtained for a composite sample programmed by bending when a magnetic field strength of Hhigh = 11.2 kA·m-1 was applied in a multi-cyclic magnetic bending experiment with 600 heating-cooling cycles it could be shown that the actuation performance did not change with increasing number of test cycles, demonstrating the accuracy and reproducibility of this soft actuator. The degree of actuation as well as the kinetics of the shape changes during heating could be tuned by variation of the magnetic filed strength between Hlow and Hhigh or the magnetic field exposure time. When Hreset = 30.0 kA·m-1 was applied the programmed geometry was erased and the composite sample returned to it´s originally straight shape. The reprogrammability of the nanocomposite actuators was demonstrated by one and the same test specimen first exhibiting reversible angle changes when programmed by bending, secondly reprogrammed to a concertina, which expands upon inductive heating and contracts during cooling and finally reprogrammed to a clip like shape, which closes during cooling and opens when Hhigh was applied. In a next step the applicability of the presented remote controllable shape-memory polymer actuators was demonstrated by repetitive opening and closing of a multiring device prepared from NC-mNP-OCL, which repetitively opens and closes when a alternating magnetic field (Hhigh = 11.2 kA·m-1) was switched on and off. For investigation of the micro- and nanostructural changes related to the actuation of the developed nanocomposite, AFM and WAXS experiments were conducted with programmed nanocomposite samples under cyclic heating and cooling between 25 °C and 60 °C. In AFM experiments the change in the distance (D) between representative droplet-like structures related to the OPDL geometry determining domains was used to calculate the reversible change in D. Here Drev = 3.5±1\% was found for NC-mNP-OCL which was in good agreement with the results of the magneto-mechanical actuation experiments. Finally, the analysis of azimuthal (radial) WAXS scattering profiles could support the oriented crystallization of the OCL actuation domains at 25 °C. In conclusion, the results of this work successfully demonstrated that shape-memory polymer nanocomposites, containing mNPs as magneto-sensitive multifunctional netpoints in a covalently crosslinked multiphase polymer matrix, exhibit magnetically (remotely) controlled actuations upon repetitive exposure to an alternating magnetic field. Furthermore, the (shape) memory of such a nanocomposite can be erased by exposing it to temperatures above the melting temperature of the geometry forming domains, which allows a reprogramming of the actuator. These findings would be relevant for designing novel reprogrammable remotely controllable soft polymeric actuators.}, language = {en} } @phdthesis{Baryzewska2023, author = {Baryzewska, Agata W.}, title = {Reconfigurable Janus emulsions as signal transducers for biosensing applications}, school = {Universit{\"a}t Potsdam}, pages = {133}, year = {2023}, language = {en} } @phdthesis{Ihlenburg2023, author = {Ihlenburg, Ramona}, title = {Sulfobetainhydrogele mit biomedizinischem Anwendungspotential und deren Netzwerkcharakterisierung im Gleichgewichtsquellzustand}, doi = {10.25932/publishup-60709}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-607093}, school = {Universit{\"a}t Potsdam}, pages = {xi, 228, xlviii}, year = {2023}, abstract = {In dieser Dissertation konnten erfolgreich mechanisch stabile Hydrogele {\"u}ber eine freie radikalische Polymerisation (FRP) in Wasser synthetisiert werden. Dabei diente vor allem das Sulfobetain SPE als Monomer. Dieses wurde mit dem {\"u}ber eine nukleophile Substitution erster bzw. zweiter Ordnung hergestellten Vernetzer TMBEMPA/Br umgesetzt. Die entstandenen Netzwerke wurden im Gleichgewichtsquellzustand im Wesentlichen mittels Niederfeld-Kernresonanzspektroskopie, R{\"o}ntgenkleinwinkelstreuung (SAXS), Rasterelektronenmikroskopie mit Tieftemperaturtechnik (Kryo-REM), dynamisch-mechanische Analyse (DMA), Rheologie, thermogravimetrische Analyse (TGA) und dynamische Differenzkalorimetrie (DSC) analysiert. Das hierarchisch aufgebaute Netzwerk wurde anschließend f{\"u}r die matrixgesteuerten Mineralisation von Calciumphosphat und -carbonat genutzt. {\"U}ber das alternierende Eintauchverfahren (engl. „alternate soaking method") und der Variation von Mineralisationsparametern, wie pH-Wert, Konzentration c und Temperatur T konnten dann verschiedene Modifikationen des Calciumphosphats generiert werden. Das entstandene Hybridmaterial wurde qualitativ mittels R{\"o}ntgenpulverdiffraktometrie (XRD), abgeschw{\"a}chte Totalreflexion-fouriertransformierte Infrarot Spektroskopie (ATR-FTIR), Raman-Spektroskopie, Rasterelektronenmikroskopie (REM) mit energiedispersiver R{\"o}ntgenspektroskopie (EDXS) und optischer Mikroskopie (OM) als auch quantitative mittels Gravimetrie und TGA analysiert. F{\"u}r die potentielle Verwendung in der Medizintechnik, z.B. als Implantatmaterial, ist die grundlegende Einsch{\"a}tzung der Wechselwirkung zwischen Hydrogel bzw. Hybridmaterial und verschiedener Zelltypen unerl{\"a}sslich. Dazu wurden verschiedene Zelltypen, wie Einzeller, Bakterien und adulte Stammzellen verwendet. Die Wechselwirkung mit Peptidsequenzen von Phagen komplettiert das biologische Unterkapitel. Hydrogele sind mannigfaltig einsetzbar. Diese Arbeit fasst daher weitere Projektperspektiven, auch außerhalb des biomedizinischem Anwendungsspektrums, auf. So konnten erste Ans{\"a}tze zur serienm{\"a}ßige bzw. maßgeschneiderte Produktion {\"u}ber das „Inkjet" Verfahren erreicht werden. Um dies erm{\"o}glichen zu k{\"o}nnen wurden erfolgreich weitere Synthesestrategien, wie die Photopolymerisation und die redoxinitiierte Polymerisation, ausgenutzt. Auch die Eignung als Filtermaterial oder Superabsorber wurde analysiert.}, language = {de} } @phdthesis{Lehmann2020, author = {Lehmann, Frederike Felizia}, title = {Solubility limits and phase stabilizing effects of mixed hybrid perovskites}, school = {Universit{\"a}t Potsdam}, year = {2020}, abstract = {In recent years the development of renewable energy sources attracted much attention due to the increasing environmental pollution induced by burning fossil fuels. The growing public interest in reducing greenhouse gases and the use of pollution-free energies (bio-mass-, geothermal-, solar-, water- or wind energy) paved the way for scientific research in renewable energies. [1] Solar energy provides unlimited access and offers high applicational flexibility, which is needed for energy consumption in a modern society. The scientific interest in photovoltaics (PV) nowadays focuses on discovering new materials and improving materials properties, aiming for the production of highly efficient solar cells. Lately, a new type of absorber material based on the perovskite type structure reached power conversion efficiencies of more than 24\%. [2] By varying the chemical composition the electronic properties as e.g. the band gap energy can be tuned to increase the absorption range of this absorber material. This makes them in particular attractive for use in tandem solar cells, where silicon and perovskite absorber layers are combined to absorb a large range of the vible light (28.0\% efficiency). [2] However, perovskite based solar cells not only suffer from fast degradation when exposed to humidity, but also from the use of toxic elements (e.g. lead), which can result in long-term environmental damage. Therefore, the aim of this study was to determine the fundamental structural and optoelectronical properties of highly interesting hybrid perovskite materials, the MAPbX3 solid solution (MA=CH3NH3; X=I,Br,Cl) and the triple cation (FA1-xMAx)1-yCsyPbI3 solid solution (FA=HC(NH2)2). The study was performed on powder samples by using X-ray diffraction, revealing the crystal structure and solubility behavior of all solid solutions. Moreover the temperature-dependent behavior was studied using in-situ high resolution synchrotron X-ray diffraction and combinatorial thermal analysis methods. The influence of compositional changes on the band gap energy variation were observed using spectroscopic methods as photoluminescence and diffuse reflectance spectroscopy. The obtained results have shown that for the MAPb(I1-xBrx)3 solid solution a large miscibility gap in the range of 0.29 ( ± 0.02) ≤ x ≤ 0.92 ( ± 0.02) is present. This miscibility gap limits the suitable compositional range for use in thin film solar cells of mixed halide compounds. From the temperature-dependent in-situ synchrotron X-ray diffraction studies the complete T-X-phase diagram was established. Studies on the MAPb(Cl1-xBrx)3 solid solution revealed that MAPb(Cl1-xBrx)3 forms a complete solid solution series. For the triple cation (FA1-xMAx)1-yCsyPbI3 solid solution the aim was to study the formation of the d-modification in FAPbI3, which is undesired for solar cell application. This can be overcome by stabilizing the favored high temperature cubic a-modification at ambient conditions. By partial substituting the formamidinium molecule by methylammonium and cesium the stabilization of the cubic modification was successful. The solubility limit of FA1-xCsxPbI3 solid solution was determined to be x=0.1, while a full miscibility was observed for the FA1-xMAxPbI3 solid solution. For the triple cation (FA1-xMAx)1-yCsyPbI3 solid solution a solubility limit of cesium was observed to be y=0.1. The optoelectronic properties were investigated, revealing a linear change of band gap energy with chemical composition. It is demonstrated that the stabilized triple cation compound with cubic perovskite-type crystal structure shows enhanced stability of approximately six months. Furthermore, a short insight into lead-free perovskite-type materials is given, using germanium as non-toxic alternative to lead. For germanium based perovskites a fast decomposition in air was observed, due to the preferred formation of GeI4 in oxygen atmosphere. In-situ low temperature synchrotron X-ray diffraction measurements revealed a yet unknown low temperature modification of MAGeI3. [1] WESSELAK, Viktor; SCHABBACH, Thomas; LINK, Thomas; FISCHER, Joachim: Handbuch Regenerative Energietechnik. Springer, 2017 [2] NREL: Best Research-Cell Efficiencies. https://www.nrel.gov/pv/assets/pdfs/best-research-cell-efficiencies-190416.pdf. - 25.04.2019}, language = {en} } @phdthesis{Breternitz2023, author = {Breternitz, Joachim}, title = {Structural systematic investigations of photovoltaic absorber materials}, school = {Universit{\"a}t Potsdam}, pages = {189}, year = {2023}, abstract = {The direct conversion of light from the sun into usable forms of energy marks one of the central cornerstones of the change of our living from the use of fossil, non-renewable energy resources towards a more sustainable economy. Besides the necessary societal changes necessary, it is the understanding of the solids employed that is of particular importance for the success of this target. In this work, the principles and approaches of systematic-crystallographic characterisation and systematisation of solids is used and employed to allow a directed tuning of the materials properties. The thorough understanding of the solid-state forms hereby the basis, on which more applied approaches are founded. Two material systems, which are considered as promising solar absorber materials, are at the core of this work: halide perovskites and II-IV-N2 nitride materials. While the first is renowned for its high efficiencies and rapid development in the last years, the latter is putting an emphasis on true sustainability in that toxic and scarce elements are avoided.}, language = {en} } @phdthesis{Chea2022, author = {Chea, Sany}, title = {Glycomaterials: From synthesis of glycoconjugates to potential biomedical applications}, doi = {10.25932/publishup-57424}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-574240}, school = {Universit{\"a}t Potsdam}, pages = {XVII, 217}, year = {2022}, abstract = {The importance of carbohydrate structures is enormous due to their ubiquitousness in our lives. The development of so-called glycomaterials is the result of this tremendous significance. These are not exclusively used for research into fundamental biological processes, but also, among other things, as inhibitors of pathogens or as drug delivery systems. This work describes the development of glycomaterials involving the synthesis of glycoderivatives, -monomers and -polymers. Glycosylamines were synthesized as precursors in a single synthesis step under microwave irradiation to significantly shorten the usual reaction time. Derivatization at the anomeric position was carried out according to the methods developed by Kochetkov and Likhorshetov, which do not require the introduction of protecting groups. Aminated saccharide structures formed the basis for the synthesis of glycomonomers in β-configuration by methacrylation. In order to obtain α-Man-based monomers for interactions with certain α-Man-binding lectins, a monomer synthesis by Staudinger ligation was developed in this work, which also does not require protective groups. Modification of the primary hydroxyl group of a saccharide was accomplished by enzyme-catalyzed synthesis. Ribose-containing cytidine was transesterified using the lipase Novozym 435 and microwave irradiation. The resulting monomer synthesis was optimized by varying the reaction partners. To create an amide bond instead of an ester bond, protected cytidine was modified by oxidation followed by amide coupling to form the monomer. This synthetic route was also used to isolate the monomer from its counterpart guanosine. After obtaining the nucleoside-based monomers, they were block copolymerized using the RAFT method. Pre-synthesized pHPMA served as macroCTA to yield cytidine- or guanosine-containing block copolymer. These isolated block copolymers were then investigated for their self-assembly behavior using UV-Vis, DLS and SEM to serve as a potential thermoresponsive drug delivery system.}, language = {en} } @phdthesis{Djalali2023, author = {Djalali, Saveh Arman}, title = {Multiresponsive complex emulsions: Concepts for the design of active and adaptive liquid colloidal systems}, doi = {10.25932/publishup-57520}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-575203}, school = {Universit{\"a}t Potsdam}, pages = {151}, year = {2023}, abstract = {Complex emulsions are dispersions of kinetically stabilized multiphasic emulsion droplets comprised of two or more immiscible liquids that provide a novel material platform for the generation of active and dynamic soft materials. In recent years, the intrinsic reconfigurable morphological behavior of complex emulsions, which can be attributed to the unique force equilibrium between the interfacial tensions acting at the various interfaces, has become of fundamental and applied interest. As such, particularly biphasic Janus droplets have been investigated as structural templates for the generation of anisotropic precision objects, dynamic optical elements or as transducers and signal amplifiers in chemo- and bio-sensing applications. In the present thesis, switchable internal morphological responses of complex droplets triggered by stimuli-induced alterations of the balance of interfacial tensions have been explored as a universal building block for the design of multiresponsive, active, and adaptive liquid colloidal systems. A series of underlying principles and mechanisms that influence the equilibrium of interfacial tensions have been uncovered, which allowed the targeted design of emulsion bodies that can alter their shape, bind and roll on surfaces, or change their geometrical shape in response to chemical stimuli. Consequently, combinations of the unique triggerable behavior of Janus droplets with designer surfactants, such as a stimuli-responsive photosurfactant (AzoTAB) resulted for instance in shape-changing soft colloids that exhibited a jellyfish inspired buoyant motion behavior, holding great promise for the design of biological inspired active material architectures and transformable soft robotics. In situ observations of spherical Janus emulsion droplets using a customized side-view microscopic imaging setup with accompanying pendant dropt measurements disclosed the sensitivity regime of the unique chemical-morphological coupling inside complex emulsions and enabled the recording of calibration curves for the extraction of critical parameters of surfactant effectiveness. The deduced new "responsive drop" method permitted a convenient and cost-efficient quantification and comparison of the critical micelle concentrations (CMCs) and effectiveness of various cationic, anionic, and nonionic surfactants. Moreover, the method allowed insightful characterization of stimuli-responsive surfactants and monitoring of the impact of inorganic salts on the CMC and surfactant effectiveness of ionic and nonionic surfactants. Droplet functionalization with synthetic crown ether surfactants yielded a synthetically minimal material platform capable of autonomous and reversible adaptation to its chemical environment through different supramolecular host-guest recognition events. Addition of metal or ammonium salts resulted in the uptake of the resulting hydrophobic complexes to the hydrocarbon hemisphere, whereas addition of hydrophilic ammonium compounds such as amino acids or polypeptides resulted in supramolecular assemblies at the hydrocarbon-water interface of the droplets. The multiresponsive material platform enabled interfacial complexation and thus triggered responses of the droplets to a variety of chemical triggers including metal ions, ammonium compounds, amino acids, antibodies, carbohydrates as well as amino-functionalized solid surfaces. In the final chapter, the first documented optical logic gates and combinatorial logic circuits based on complex emulsions are presented. More specifically, the unique reconfigurable and multiresponsive properties of complex emulsions were exploited to realize droplet-based logic gates of varying complexity using different stimuli-responsive surfactants in combination with diverse readout methods. In summary, different designs for multiresponsive, active, and adaptive liquid colloidal systems were presented and investigated, enabling the design of novel transformative chemo-intelligent soft material platforms.}, language = {en} } @phdthesis{Nagel2023, author = {Nagel, Alessandro}, title = {Energie induzierte Nanopartikel-Substrat Interaktionen}, doi = {10.25932/publishup-59639}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-596396}, school = {Universit{\"a}t Potsdam}, pages = {IV, 251}, year = {2023}, abstract = {Im Rahmen dieser Arbeit wurden Energie induzierte Nanopartikel-Substrat Interaktionen untersucht. Dazu wurden Goldnanopartikelanordnungen (AuNPA) auf verschiedenen Silizium-basierten Substraten hergestellt und der Einfluss eines Energieeintrages, genauer gesagt einer thermischen Behandlung oder des Metall-assistierten chemischen {\"A}tzens (MaCE) getestet. Die Nanopartikelanordnungen, welche f{\"u}r die thermische Behandlung eingesetzt wurden, wurden nass-chemisch in Toluol synthetisiert, mit Thiol-terminiertem Polystyrol funktionalisiert und mittels Schleuderbeschichtung auf verschiedenen Substraten (drei Gl{\"a}ser und ein Siliziumwafer) in quasi-hexagonalen Mustern angeordnet. Diese AuNP-Anordnungen wurden mit Temperaturen zwischen 475 °C - 792 °C {\"u}ber verschiedene Zeitr{\"a}ume thermisch behandelt. Generell sanken die Nanopartikel in die Substrate ein, und es wurde festgestellt, dass mit Erh{\"o}hung der Glas{\"u}bergangstemperatur der Substrate die Einsinktiefe der Nanopartikel abnahm. Die AuNPA auf Siliziumwafern wurden auf Temperaturen von 700 °C - 900 °C erhitzt. Die Goldnanopartikel sanken dabei bis zu 2,5 nm in das Si-Substrat ein. Ein Sintern der Nanopartikel fand ab einer Temperatur {\"u}ber 660 °C statt. Welcher Sintermechanismus der dominante ist konnte abschließend nicht eindeutig gekl{\"a}rt werden. F{\"u}r die Untersuchung des Einflusses des zweiten Energieeintrages mittels MaCE wurden AuNPA sowie Goldkern-Silberschale-Anordnungen auf Siliziumsubstraten genutzt. Die AuNPA wurden mit Hilfe von Poly-N-Isopropylacrylamid Mikrogelen und Natriumcitrat-stabilisierten Goldnanopartikeln (Na-AuNP) bzw. Tetrachloridogolds{\"a}ure (TCG) pr{\"a}pariert. Es ergaben sich Nanopartikelanordnungen mit hemisph{\"a}rischen Partikeln (aus Na-AuNP) und zum anderen Nanopartikelanordnungen mit sph{\"a}rischen Partikeln (aus TCG). Durch eine anschließende Silberwachstumsreaktion konnten dann die dazugeh{\"o}rigen Goldkern-Silberschale Nanopartikelanordnungen erhalten werden. Beim MaCE konnten signifikante Unterschiede im Verhalten dieser vier Nanopartikelanordnungen festgestellt werden, z.B. mussten bei den hemisph{\"a}rischen Partikelanordnungen h{\"o}here Wasserstoffperoxidkonzentrationen (0,70 M - 0,91 M) als bei den sph{\"a}rischen Partikelanordnungen (0,08 M - 0,32 M) f{\"u}r das {\"A}tzen eingesetzt werden, um ein Einsinken der Nanopartikel in das Substrat zu erreichen.}, language = {de} } @phdthesis{Kim2023, author = {Kim, Jiyong}, title = {Synthesis of InP quantum dots and their applications}, doi = {10.25932/publishup-58535}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-585351}, school = {Universit{\"a}t Potsdam}, pages = {XIX, 142}, year = {2023}, abstract = {Technologically important, environmentally friendly InP quantum dots (QDs) typically used as green and red emitters in display devices can achieve exceptional photoluminescence quantum yields (PL QYs) of near-unity (95-100\%) when the-state-of-the-art core/shell heterostructure of the ZnSe inner/ZnS outer shell is elaborately applied. Nevertheless, it has only led to a few industrial applications as QD liquid crystal display (QD-LCD) which is applied to blue backlight units, even though QDs has a lot of possibilities that able to realize industrially feasible applications, such as QD light-emitting diodes (QD‒LEDs) and luminescence solar concentrator (LSC), due to their functionalizable characteristics. Before introducing the main research, the theoretical basis and fundamentals of QDs are described in detail on the basis of the quantum mechanics and experimental synthetic results, where a concept of QD and colloidal QD, a type-I core/shell structure, a transition metal doped semiconductor QDs, the surface chemistry of QD, and their applications (LSC, QD‒LEDs, and EHD jet printing) are sequentially elucidated for better understanding. This doctoral thesis mainly focused on the connectivity between QD materials and QD devices, based on the synthesis of InP QDs that are composed of inorganic core (core/shell heterostructure) and organic shell (surface ligands on the QD surface). In particular, as for the former one (core/shell heterostructure), the ZnCuInS mid-shell as an intermediate layer is newly introduced between a Cu-doped InP core and a ZnS shell for LSC devices. As for the latter one (surface ligands), the ligand effect by 1-octanethiol and chloride ion are investigated for the device stability in QD‒LEDs and the printability of electro-hydrodynamic (EHD) jet printing system, in which this research explores the behavior of surface ligands, based on proton transfer mechanism on the QD surface. Chapter 3 demonstrates the synthesis of strain-engineered highly emissive Cu:InP/Zn-Cu-In-S (ZCIS)/ZnS core/shell/shell heterostructure QDs via a one-pot approach. When this unconventional combination of a ZCIS/ZnS double shelling scheme is introduced to a series of Cu:InP cores with different sizes, the resulting Cu:InP/ZCIS/ZnS QDs with a tunable near-IR PL range of 694-850 nm yield the highest-ever PL QYs of 71.5-82.4\%. These outcomes strongly point to the efficacy of the ZCIS interlayer, which makes the core/shell interfacial strain effectively alleviated, toward high emissivity. The presence of such an intermediate ZCIS layer is further examined by comparative size, structural, and compositional analyses. The end of this chapter briefly introduces the research related to the LSC devices, fabricated from Cu:InP/ZCIS/ZnS QDs, currently in progress. Chapter 4 mainly deals with ligand effect in 1-octanethiol passivation of InP/ZnSe/ZnS QDs in terms of incomplete surface passivation during synthesis. This chapter demonstrates the lack of anionic carboxylate ligands on the surface of InP/ZnSe/ZnS quantum dots (QDs), where zinc carboxylate ligands can be converted to carboxylic acid or carboxylate ligands via proton transfer by 1-octanethiol. The as-synthesized QDs initially have an under-coordinated vacancy surface, which is passivated by solvent ligands such as ethanol and acetone. Upon exposure of 1-octanethiol to the QD surface, 1-octanthiol effectively induces the surface binding of anionic carboxylate ligands (derived from zinc carboxylate ligands) by proton transfer, which consequently exchanges ethanol and acetone ligands that bound on the incomplete QD surface. The systematic chemical analyses, such as thermogravimetric analysis‒mass spectrometry and proton nuclear magnetic resonance spectroscopy, directly show the interplay of surface ligands, and it associates with QD light-emitting diodes (QD‒LEDs). Chapter 5 shows the relation between material stability of QDs and device stability of QD‒LEDs through the investigation of surface chemistry and shell thickness. In typical III-V colloidal InP quantum dots (QDs), an inorganic ZnS outermost shell is used to provide stability when overcoated onto the InP core. However, this work presents a faster photo-degradation of InP/ZnSe/ZnS QDs with a thicker ZnS shell than that with a thin ZnS shell when 1-octanethiol was applied as a sulfur source to form ZnS outmost shell. Herein, 1-octanethiol induces the form of weakly-bound carboxylate ligand via proton transfer on the QD surface, resulting in a faster degradation at UV light even though a thicker ZnS shell was formed onto InP/ZnSe QDs. Detailed insight into surface chemistry was obtained from proton nuclear magnetic resonance spectroscopy and thermogravimetric analysis-mass spectrometry. However, the lifetimes of the electroluminescence devices fabricated from InP/ZnSe/ZnS QDs with a thick or a thin ZnS shell show surprisingly the opposite result to the material stability of QDs, where the QD light-emitting diodes (QD‒LEDs) with a thick ZnS shelled QDs maintained its luminance more stable than that with a thin ZnS shelled QDs. This study elucidates the degradation mechanism of the QDs and the QD light-emitting diodes based on the results and discuss why the material stability of QDs is different from the lifetime of QD‒LEDs. Chapter 6 suggests a method how to improve a printability of EHD jet printing when QD materials are applied to QD ink formulation, where this work introduces the application of GaP mid-shelled InP QDs as a role of surface charge in EHD jet printing technique. In general, GaP intermediate shell has been introduced in III-V colloidal InP quantum dots (QDs) to enhance their thermal stability and quantum efficiency in the case of type-I core/shell/shell heterostructure InP/GaP/ZnSeS QDs. Herein, these highly luminescent InP/GaP/ZnSeS QDs were synthesized and applied to EHD jet printing, by which this study demonstrates that unreacted Ga and Cl ions on the QD surface induce the operating voltage of cone jet and cone jet formation to be reduced and stabilized, respectively. This result indicates GaP intermediate shell not only improves PL QY and thermal stability of InP QDs but also adjusts the critical flow rate required for cone-jet formation. In other words, surface charges of quantum dots can have a significant role in forming cone apex in the EHD capillary nozzle. For an industrially convenient validation of surface charges on the QD surface, Zeta potential analyses of QD solutions as a simple method were performed, as well as inductively coupled plasma optical emission spectrometry (ICP-OES) for a composition of elements. Beyond the generation of highly emissive InP QDs with narrow FWHM, these studies talk about the connection between QD material and QD devices not only to make it a vital jumping-off point for industrially feasible applications but also to reveal from chemical and physical standpoints the origin that obstructs the improvement of device performance experimentally and theoretically.}, language = {en} } @phdthesis{Lepre2023, author = {Lepre, Enrico}, title = {Nitrogen-doped carbonaceous materials for energy and catalysis}, doi = {10.25932/publishup-57739}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-577390}, school = {Universit{\"a}t Potsdam}, pages = {153}, year = {2023}, abstract = {Facing the environmental crisis, new technologies are needed to sustain our society. In this context, this thesis aims to describe the properties and applications of carbon-based sustainable materials. In particular, it reports the synthesis and characterization of a wide set of porous carbonaceous materials with high nitrogen content obtained from nucleobases. These materials are used as cathodes for Li-ion capacitors, and a major focus is put on the cathode preparation, highlighting the oxidation resistance of nucleobase-derived materials. Furthermore, their catalytic properties for acid/base and redox reactions are described, pointing to the role of nitrogen speciation on their surfaces. Finally, these materials are used as supports for highly dispersed nickel loading, activating the materials for carbon dioxide electroreduction.}, language = {en} } @phdthesis{Simsek2022, author = {Simsek, Ibrahim}, title = {Ink-based preparation of chalcogenide perovskites as thin films for PV applications}, doi = {10.25932/publishup-57271}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-572711}, school = {Universit{\"a}t Potsdam}, pages = {iv, 113}, year = {2022}, abstract = {The increasing demand for energy in the current technological era and the recent political decisions about giving up on nuclear energy diverted humanity to focus on alternative environmentally friendly energy sources like solar energy. Although silicon solar cells are the product of a matured technology, the search for highly efficient and easily applicable materials is still ongoing. These properties made the efficiency of halide perovskites comparable with silicon solar cells for single junctions within a decade of research. However, the downside of halide perovskites are poor stability and lead toxicity for the most stable ones. On the other hand, chalcogenide perovskites are one of the most promising absorber materials for the photovoltaic market, due to their elemental abundance and chemical stability against moisture and oxygen. In the search of the ultimate solar absorber material, combining the good optoelectronic properties of halide perovskites with the stability of chalcogenides could be the promising candidate. Thus, this work investigates new techniques for the synthesis and design of these novel chalcogenide perovskites, that contain transition metals as cations, e.g., BaZrS3, BaHfS3, EuZrS3, EuHfS3 and SrHfS3. There are two stages in the deposition techniques of this study: In the first stage, the binary compounds are deposited via a solution processing method. In the second stage, the deposited materials are annealed in a chalcogenide atmosphere to form the perovskite structure by using solid-state reactions. The research also focuses on the optimization of a generalized recipe for a molecular ink to deposit precursors of chalcogenide perovskites with different binaries. The implementation of the precursor sulfurization resulted in either binaries without perovskite formation or distorted perovskite structures, whereas some of these materials are reported in the literature as they are more favorable in the needle-like non-perovskite configuration. Lastly, there are two categories for the evaluation of the produced materials: The first category is about the determination of the physical properties of the deposited layer, e.g., crystal structure, secondary phase formation, impurities, etc. For the second category, optoelectronic properties are measured and compared to an ideal absorber layer, e.g., band gap, conductivity, surface photovoltage, etc.}, language = {en} } @phdthesis{Heyne2022, author = {Heyne, Benjamin}, title = {Design and Synthesis of Highly Efficient InPZnS/ZnSe/ZnS Multishell Quantum Dots and Phase Transfer via Ligand Exchange}, school = {Universit{\"a}t Potsdam}, pages = {102,LII}, year = {2022}, language = {en} } @phdthesis{Xie2023, author = {Xie, Dongjiu}, title = {Nanostructured Iron-based compounds as sulfur host material for lithium-sulfur batteries}, doi = {10.25932/publishup-61036}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-610369}, school = {Universit{\"a}t Potsdam}, pages = {viii, 142}, year = {2023}, abstract = {The present thesis focuses on the synthesis of nanostructured iron-based compounds by using β-FeOOH nanospindles and poly(ionic liquid)s (PILs) vesicles as hard and soft templates, respectively, to suppress the shuttle effect of lithium polysulfides (LiPSs) in Li-S batteries. Three types of composites with different nanostructures (mesoporous nanospindle, yolk-shell nanospindle, and nanocapsule) have been synthesized and applied as sulfur host material for Li-S batteries. Their interactions with LiPSs and effects on the electrochemical performance of Li-S batteries have been systematically studied. In the first part of the thesis, carbon-coated mesoporous Fe3O4 (C@M-Fe3O4) nanospindles have been synthesized to suppress the shuttle effect of LiPSs. First, β-FeOOH nanospindles have been synthesized via the hydrolysis of iron (III) chloride in aqueous solution and after silica coating and subsequent calcination, mesoporous Fe2O3 (M-Fe2O3) have been obtained inside the confined silica layer through pyrolysis of β-FeOOH. After the removal of the silica layer, electron tomography (ET) has been applied to rebuild the 3D structure of the M-Fe2O3 nanospindles. After coating a thin layer of polydopamine (PDA) as carbon source, the PDA-coated M-Fe2O3 particles have been calcinated to synthesize C@M-Fe3O4 nanospindles. With the chemisorption of Fe3O4 and confinement of mesoporous structure to anchor LiPSs, the composite C@M-Fe3O4/S electrode delivers a remaining capacity of 507.7 mAh g-1 at 1 C after 600 cycles. In the second part of the thesis, a series of iron-based compounds (Fe3O4, FeS2, and FeS) with the same yolk-shell nanospindle morphology have been synthesized, which allows for the direct comparison of the effects of compositions on the electrochemical performance of Li-S batteries. The Fe3O4-carbon yolk-shell nanospindles have been synthesized by using the β-FeOOH nanospindles as hard template. Afterwards, Fe3O4-carbon yolk-shell nanospindles have been used as precursors to obtain iron sulfides (FeS and FeS2)-carbon yolk-shell nanospindles through sulfidation at different temperatures. Using the three types of yolk-shell nanospindles as sulfur host, the effects of compositions on interactions with LiPSs and electrochemical performance in Li-S batteries have been systematically investigated and compared. Benefiting from the chemisorption and catalytic effect of FeS2 particles and the physical confinement of the carbon shell, the FeS2-C/S electrode exhibits the best electrochemical performance with an initial specific discharge capacity of 877.6 mAh g-1 at 0.5 C and a retention ratio of 86.7\% after 350 cycles. In the third part, PILs vesicles have been used as soft template to synthesize carbon nanocapsules embedded with iron nitride particles to immobilize and catalyze LiPSs in Li-S batteries. First, 3-n-decyl-1-vinylimidazolium bromide has been used as monomer to synthesize PILs nanovesicles by free radical polymerization. Assisted by PDA coating route and ion exchange, PIL nanovesicles have been successfully applied as soft template in morphology-maintaining carbonization to prepare carbon nanocapsules embedded with iron nitride nanoparticles (FexN@C). The well-dispersed iron nitride nanoparticles effectively catalyze the conversion of LiPSs to Li2S, owing to their high electrical conductivity and strong chemical binding to LiPSs. The constructed FexN@C/S cathode demonstrates a high initial discharge capacity of 1085.0 mAh g-1 at 0.5 C with a remaining value of 930.0 mAh g-1 after 200 cycles. The results in the present thesis demonstrate the facile synthetic routes of nanostructured iron-based compounds with controllable morphologies and compositions using soft and hard colloidal templates, which can be applied as sulfur host to suppress the shuttle behavior of LiPSs. The synthesis approaches developed in this thesis are also applicable to fabricating other transition metal-based compounds with porous nanostructures for other applications.}, language = {en} } @phdthesis{NaderiMehr2019, author = {Naderi Mehr, Fatemeh}, title = {Preparation and self-assembly behavior of anisotropic polymer patchy particles}, pages = {74, XX}, year = {2019}, language = {en} } @phdthesis{Cataldo2020, author = {Cataldo, Vincenzo Alessandro}, title = {Design and synthesis of alkylating ionic liquids and their application in synthesis, materials and proteomics}, school = {Universit{\"a}t Potsdam}, pages = {153}, year = {2020}, language = {en} } @phdthesis{Piankova2022, author = {Piankova, Diana}, title = {Electron pair distribution function (ePDF) analysis and advanced transmission electron microscopy (TEM) techniques}, school = {Universit{\"a}t Potsdam}, pages = {XIX, 146}, year = {2022}, language = {en} } @phdthesis{Lian2023, author = {Lian, Tingting}, title = {Efficient activation of peroxymonosulfate by carbon-based catalysts for water purification}, school = {Universit{\"a}t Potsdam}, pages = {167}, year = {2023}, abstract = {The increasing global population has led to a growing demand for cost-effective and eco-friendly methods of water purification. This demand has reached a peak due to the increasing presence of impurities and pollutants in water and a growing awareness of waterborne diseases. Advanced oxidation processes (AOPs) are effective methods to address these challenges, due to the generation of highly reactive radicals, such as sulfate radical (SO4•-), hydroxyl radical (•OH), and/or superoxide radical (•O2-) in oxidation reactions. Relative to conventional hydrogen peroxide (H2O2)-based AOPs for wastewater treatment, the persulfate-related AOPs are receiving increasing attention over the past decades, due to their stronger oxidizing capability and a wider pH working window. Further deployment of the seemingly plausible technology as an alternative for the well-established one in industry, however, necessitates a careful evaluation of compounding factors, such as water matrix effects, toxicological consequences, costs, and engineering challenges, etc. To this end, rational design of efficient and environmentally friendly catalysts constitutes an indispensable pathway to advance persulfate activation efficacy and to elucidate the mechanisms in AOPs, the combined endeavors are expected to provide insightful understanding and guidelines for future studies in wastewater treatment. A dozens of transition metal-based catalysts have been developed for persulfate-related AOPs, while the undesirable metal leaching and poor stability in acidic conditions have been identified as major obstacles. Comparatively, the carbonaceous materials are emerging as alternative candidates, which are characterized by metal-free nature, wide availability, and exceptional resistance to acid and alkali, as well as tunable physicochemical and electronic properties, the combined merits make them an attractive option to overcome the aforementioned limitations in metal-based catalytic systems. This dissertation aims at developing novel carbonaceous materials to boost the activity in peroxymonosulfate (PMS) activation processes. Functionalized carbon materials with metal particles or heteroatoms were constructed and further evaluated in terms of their ability to activate PMS for AOPs. The main contents of this thesis are summarized as follows: (1) Iron oxide-loaded biochar: improving stability and alleviating metal leakage Metal leaching constitutes one of the main drawbacks in using transition metals as PMS activators, which is accompanied by the generation of metal-containing sludge, potentially leading to secondary pollution. Meanwhile, the metal nanoparticles are prone to aggregate, causing rapid decay of catalytic performance. The use of carbons as supports for transition metals could mitigate these deficiencies, because the interaction between metals and carbons could in turn disperse and stabilize metal nanoparticles, thus suppressing the metal leaching. In this work, the environmentally benign lignin with its abundant phenolic groups, which is well known to serve as carbon source with high yields and flexibility, was utilized to load Fe ions. The facile low-temperature pre-treatment pyrolytic strategy was employed to construct a green catalyst with iron oxides embedded in Kraft-lignin-derived biochar (termed as γ-Fe2O3@KC). The γ-Fe2O3@KC was capable of activating PMS to generate stable non-radical species (1O2 and Fe (V)=O) and to enhance electron transfer efficiency. A surface-bound reactive complex (catalyst-PMS*) was identified by electrochemical characterizations and discussed with primary surface-bound radical pairs to explain the contradictions between quenching and EPR detection results. The system also showed encouraging reusability for at least 5 times and high stability at pH 3-9. The low concentration of iron in γ-Fe2O3@KC/PMS system implied that the carbon scaffold of biochar substantially alleviated metal leakage. (2) MOF-derived nanocarbon: new carbon crystals Traditional carbon materials are of rather moderate performance in activation PMS, due to the poor electron transfer capacity within the amorphous structure and limited active sites for PMS adsorption. Herein, we established crystalline nanocarbon materials via a simple NaCl-templated strategy using the monoclinic zeolitic imidazolate framework-8 (ZIF-8) sealed with NaCl crystals as the precursors. Specifically, NaCl captured dual advantages in serving as structure-directing agent during hydrolysis and protective salt reactor to facilitate phase transformation during carbonization. The structure-directing agent NaCl provided a protective and confined space for the evolution of MOF upon carbonization, which led to high doping amounts of nitrogen (N) and oxygen elements (O) in carbon framework (N: 14.16 wt\%, O: 9.6 wt\%) after calcination at a high temperature of 950 oC. We found that N-O co-doping can activate the chemically inert carbon network and the nearby sp2-hybridized carbon atoms served as active sites for adsorption and activation. Besides, the highly crystallized structure with well-established carbon channels around activated carbon atoms could significantly accelerate electron transfer process after initial adsorption of PMS. As such, this crystalline nanocarbon exhibited excellent catalytic kinetics for various pollutants. (3) MOF-derived 2D carbon layers: enhanced mass/electron transfer The two-dimensional (2D) configuration of carbon-based nanosheets with inherent nanochannels and abundant active sites residing on the layer edges or in between the layers, allowed the accessible interaction and close contact between the substrates and reactants, as well as the dramatically improved electron- and mass-transfer kinetics. In this regard, we developed dual-templating strategy to afford 2D assembly of the crystalline carbons, which found efficiency in reinforcing the interactions between the catalyst surface and foreign pollutants. Specifically, we found that the ice crystals and NaCl promoted the evolution of MOF in a 2D fashion during the freezing casting stage, while the later further allowed the formation of a graphitic surface at high calcination temperature, by virtue of the templating effect of molten salt. Due to the highly retained co-doping amounts, N and O heteroatoms created abundant active sites for PMS activation, the 2D configuration of carbon-based nanosheets enable efficient interaction of PMS and pollutants on the surface, which further boosted the kinetics of degradation.}, language = {en} } @phdthesis{Abouserie2018, author = {Abouserie, Ahed}, title = {Ionic liquid precursors for multicomponent inorganic nanomaterials}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-418950}, school = {Universit{\"a}t Potsdam}, pages = {xx, 193}, year = {2018}, abstract = {Health effects, attributed to the environmental pollution resulted from using solvents such as benzene, are relatively unexplored among petroleum workers, personal use, and laboratory researchers. Solvents can cause various health problems, such as neurotoxicity, immunotoxicity, and carcinogenicity. As such it can be absorbed via epidermal or respiratory into the human body resulting in interacting with molecules that are responsible for biochemical and physiological processes of the brain. Owing to the ever-growing demand for finding a solution, an Ionic liquid can use as an alternative solvent. Ionic liquids are salts in a liquid state at low temperature (below 100 C), or even at room temperature. Ionic liquids impart a unique architectural platform, which has been interesting because of their unusual properties that can be tuned by simple ways such as mixing two ionic liquids. Ionic liquids not only used as reaction solvents but they became a key developing for novel applications based on their thermal stability, electric conductivity with very low vapor pressure in contrast to the conventional solvents. In this study, ionic liquids were used as a solvent and reactant at the same time for the novel nanomaterials synthesis for different applications including solar cells, gas sensors, and water splitting. The field of ionic liquids continues to grow, and become one of the most important branches of science. It appears to be at a point where research and industry can work together in a new way of thinking for green chemistry and sustainable production.}, language = {en} } @phdthesis{Grunert2018, author = {Grunert, Bianca}, title = {Entwicklung von Markierungsreagenzien f{\"u}r die bildgebende Diagnostik}, doi = {10.25932/publishup-42283}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-422830}, school = {Universit{\"a}t Potsdam}, pages = {155}, year = {2018}, abstract = {Die intrazellul{\"a}re Markierung mit geeigneten Reagenzien erm{\"o}glicht ihre bildgebende Darstellung in lebenden Organismen. Dieses Verfahren (auch „Zell-Tracking" genannt) wird in der Grundlagenforschung zur Entwicklung zellul{\"a}rer Therapien, f{\"u}r die Erforschung pathologischer Prozesse, wie der Metastasierung, sowie f{\"u}r Therapiekontrollen eingesetzt. Besondere Bedeutung haben in den letzten Jahren zellul{\"a}re Therapien mit Stammzellen erlangt, da sie großes Potential bei der Regeneration von Geweben bei Krankheiten wie Morbus Parkinson oder Typ-1-Diabetes versprechen. F{\"u}r die Entwicklung einer zellul{\"a}ren Therapie sind Informationen {\"u}ber den Verbleib der applizierten Zellen in vivo (Homing-Potential), {\"u}ber ihre Zellphysiologie sowie {\"u}ber die Entstehung m{\"o}glicher Entz{\"u}ndungen notwendig. Das Ziel der vorliegenden Arbeit war daher die Synthese von Markierungsreagenzien, die nicht nur eine effiziente Zellmarkierung erm{\"o}glichen, sondern einen synergistischen Effekt hinsichtlich des modalit{\"a}ts{\"u}bergreifenden Einsatzes in den bildgebenden Verfahren MRT und Laser-Ablation(LA)-ICP-MS erlauben. Die MRT-Bildgebung erm{\"o}glicht die nicht invasive Nachverfolgung markierter Zellen in vivo und die LA-ICP-MS die anschließende ex vivo Analytik zur Darstellung der Elementverteilung (Bioimaging) in einer Biopsieprobe oder in einem Gewebeschnitt. F{\"u}r diese Zwecke wurden zwei verschiedene Markierungsreagenzien mit dem kontrastgebenden Element Gadolinium synthetisiert. Gadolinium eignet sich aufgrund seines hohen magnetischen Moments hervorragend f{\"u}r die MRT-Bildgebung und da es in Biomolek{\"u}len nicht nat{\"u}rlich vorkommt, konnten die Reagenzien gleichermaßen f{\"u}r die Zellmarkierung und das Bioimaging mit der LA-ICP-MS untersucht werden. F{\"u}r die Synthese eines makromolekularen Reagenzes wurde das kommerziell verf{\"u}gbare Dendrimer G5-PAMAM {\"u}ber bifunktionelle Linker mit dem Chelator DOTA funktionalisiert, um anschließend Gadolinium zu komplexieren. Ein zweites, nanopartikul{\"a}res Reagenz wurde {\"u}ber eine Solvothermal-Synthese erhalten, bei der Ln:GdVO4-Nanokristalle mit einer funktionellen Polyacryls{\"a}ure(PAA)-H{\"u}lle dargestellt wurden. Die Dotierung der Ln:GdVO4-PAA Nanokristalle mit verschiedenen Lanthanoiden (Ln=Eu, Tb) zeigte ihre prinzipielle Multiplexf{\"a}higkeit in der LA-ICP-MS. Beide Markierungsreagenzien zeichneten sich durch gute Biovertr{\"a}glichkeiten und r1-Relaxivit{\"a}ten aus, was zudem ihr Potential f{\"u}r Anwendungen als pr{\"a}klinische „blood-pool" MRT-Kontrastmittel belegte. Die Untersuchung der Zellmarkierung erfolgte anhand einer Tumorzelllinie und einer Stammzelllinie, wobei beide Zellarten erfolgreich intrazellul{\"a}r mit beiden Reagenzien markiert wurden. Nach der Zellmarkierung veranschaulichte die in vitro MRT-Bildgebung von Zell-Phantomen eine deutlichere Kontrastverst{\"a}rkung der Zellen nach der Markierung mit den Nanokristallen im Vergleich zum kommerziellen Kontrastmittel Magnevist®. Die hohe Effizienz der Zellmarkierung mit den Nanokristallen und die damit verbundenen hohen Signalintensit{\"a}ten in einer einzelnen Zelle erlaubten beim Bioimaging mit der LA-ICP-MS, Messungen bis zu einer Aufl{\"o}sung von 4 µm Laser Spot Size. Nach der Zellmarkierung mit den DOTA(Gd3+)-funktionalisierten G5-PAMAM Dendrimeren waren hingegen Aufnahmen mit der LA-ICP-MS nur bis zu einer Aufl{\"o}sung von 12 µm Laser Spot Size m{\"o}glich. Insgesamt waren die Ln:GdVO4-PAA Nanokristalle mit gr{\"o}ßerer Ausbeute und kosteng{\"u}nstiger herstellbar als die DOTA(Gd3+)-funktionalisierten G5-PAMAM Dendrimere und zeigten zudem eine effizientere Zellmarkierung. Die Ln:GdVO4-PAA Nanokristalle erscheinen somit f{\"u}r das Zell-Tracking als besonders vielversprechend. Darauf aufbauend wurden die Nanokristalle zur Etablierung der Antik{\"o}rper-Konjugation ausgew{\"a}hlt, was sie f{\"u}r die molekulare in vivo Bildgebung sowie f{\"u}r die Immuno-Bildgebung von Gewebeschnitten oder Biopsie-Proben mit der LA-ICP-MS anwendbar macht.}, language = {de} } @phdthesis{Iqbal2023, author = {Iqbal, Zafar}, title = {Interface design and characterization for stable inorganic perovskite solar cells}, doi = {10.25932/publishup-61831}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-618315}, school = {Universit{\"a}t Potsdam}, pages = {ix, 133}, year = {2023}, abstract = {We live in an era driven by fossil fuels. The prevailing climate change suggests that we have to significantly reduce greenhouse gas emissions. The only way forward is to use renewable energy sources. Among those, solar energy is a clean, affordable, and sustainable source of energy. It has the potential to satisfy the world's energy demand in the future. However, there is a need to develop new materials that can make solar energy usable. Photovoltaics (PV) are devices that convert photon energy into electrical energy. The most commonly used solar cells are based on crystalline silicon. However, the fabrication process for silicon solar cells is technologically difficult and costly. Solar cells based on lead halide perovskites (PSCs) have emerged as a new candidate for PV applications since 2009. To date, PSCs have achieved 26\% power-conversion-efficiency (PCE) for its single junction, and 33.7\% PCE for tandem junction devices. However, there is still room for improvement in overall performance. The main challenge for the commercialization of this technology is the stability of the solar cells under operational conditions. Inorganic perovskite CsPbI3 has attracted researchers' interest due to its stability at elevated temperatures, however, inorganic perovskites also have associated challenges, e.g. phase stability, larger voltage loss compared to their organic-inorganic hybrid counterparts, and interface energy misalignment. The most efficient inorganic perovskite solar cell is stable for up to a few hundred hours while the most stable device in the field of inorganic PSCs reported so far is at 17\% PCE. This suggests the need for improvement of the interfaces for enhanced open circuit voltage (VOC), and optimization of the energy alignment at the interfaces. This dissertation presents the study on interfaces between the perovskite layer and hole transport layer (HTL) for stable CsPbI3 solar cells. The first part of the thesis presents an investigation of the CsPbI3 film annealing environment and its subsequent effects on the perovskite/HTL interface dynamics. Thin films annealed in dry air were compared with thin films annealed in ambient air. Synchrotron-based hard X-ray spectroscopy (HAXPES) measurements reveal that annealing in ambient air does not have an adverse effect; instead, those samples undergo surface band bending. This surface band modification induces changes in interface charge dynamics and, consequently, an improvement in charge extraction at the interfaces. Further, transient surface photovoltage (tr-SPV) simulations show that air-annealed samples exhibit fewer trap states compared to samples annealed in dry air. Finally, by annealing the CsPbI3 films in ambient air, a PCE of 19.8\% and Voc of 1.23 V were achieved for an n-i-p structured device. Interface engineering has emerged as a strategy to extract the charge and optimize the energy alignment in perovskite solar cells (PSCs). An interface with fewer trap states and energy band levels closer to the selective contact helps to attain improved efficiencies in PSCs. The second part of the thesis presents a design for the CsPbI3/HTM interface. In this work, an interface between CsPbI3 perovskite and its hole selective contact N2,N2,N2′,N2′,N7,N7,N7′,N7′-octakis(4-methoxyphenyl)-9,9′-spirobi[9H-fluorene]-2,2′,7,7′-tetramine(Spiro-OMeTAD), realized by trioctylphosphine oxide (TOPO), a dipole molecule is introduced. On top of a perovskite film well-passivated by n-octyl ammonium Iodide (OAI), it created an upward surface band-bending at the interface byTOPO that optimizes energy level alignment and enhances the extraction of holes from the perovskite layer to the hole transport material. Consequently, a Voc of 1.2 V and high-power conversion efficiency (PCE) of over 19\% were achieved for inorganic CsPbI3 perovskite solar cells. In addition, the work also sheds light on the interfacial charge-selectivity and the long-term stability of CsPbI3 perovskite solar cells. The third part of the thesis extends the previous studies to polymeric poly(3-hexylthiophene-2,5-diyl) (P3HT) as HTL. The CsPbI3/P3HT interface is critical due to high non-radiative recombination. This work presents a CsPbI3/P3HT interface modified with a long-chain alkyl halide molecule, n-hexyl trimethyl ammonium bromide (HTAB). This molecule largely passivates the CsPbI3 perovskite surface and improves the charge extraction across the interface. Consequently, a Voc of over 1.00 V and 14.2\% PCE were achieved for CsPbI3 with P3HT as HTM. Overall the results presented in this dissertation introduce and discuss methods to design and study the interfaces in CsPbI3-based solar cells. This study can pave the way for novel interface designs between CsPbI3 and HTM for charge extraction, efficiency and stability.}, language = {en} } @phdthesis{Bastian2022, author = {Bastian, Philipp U.}, title = {Core-shell upconversion nanoparticles - investigation of dopant intermixing and surface modification}, doi = {10.25932/publishup-55160}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-551607}, school = {Universit{\"a}t Potsdam}, pages = {XII, 108, xxiii}, year = {2022}, abstract = {Frequency upconversion nanoparticles (UCNPs) are inorganic nanocrystals capable to up-convert incident photons of the near-infrared electromagnetic spectrum (NIR) into higher energy photons. These photons are re-emitted in the range of the visible (Vis) and even ultraviolet (UV) light. The frequency upconversion process (UC) is realized with nanocrystals doped with trivalent lanthanoid ions (Ln(III)). The Ln(III) ions provide the electronic (excited) states forming a ladder-like electronic structure for the Ln(III) electrons in the nanocrystals. The absorption of at least two low energy photons by the nanoparticle and the subsequent energy transfer to one Ln(III) ion leads to the promotion of one Ln(III) electron into higher excited electronic states. One high energy photon will be emitted during the radiative relaxation of the electron in the excited state back into the electronic ground state of the Ln(III) ion. The excited state electron is the result of the previous absorption of at least two low energy photons. The UC process is very interesting in the biological/medical context. Biological samples (like organic tissue, blood, urine, and stool) absorb high-energy photons (UV and blue light) more strongly than low-energy photons (red and NIR light). Thanks to a naturally occurring optical window, NIR light can penetrate deeper than UV light into biological samples. Hence, UCNPs in bio-samples can be excited by NIR light. This possibility opens a pathway for in vitro as well as in vivo applications, like optical imaging by cell labeling or staining of specific organic tissue. Furthermore, early detection and diagnosis of diseases by predictive and diagnostic biomarkers can be realized with bio-recognition elements being labeled to the UCNPs. Additionally, "theranostic" becomes possible, in which the identification and the treatment of a disease are tackled simultaneously. For this to succeed, certain parameters for the UCNPs must be met: high upconversion efficiency, high photoluminescence quantum yield, dispersibility, and dispersion stability in aqueous media, as well as availability of functional groups to introduce fast and easy bio-recognition elements. The UCNPs used in this work were prepared with a solvothermal decomposition synthesis yielding in particles with NaYF4 or NaGdF4 as host lattice. They have been doped with the Ln(III) ions Yb3+ and Er3+, which is only one possible upconversion pair. Their upconversion efficiency and photoluminescence quantum yield were improved by adding a passivating shell to reduce surface quenching. However, the brightness of core-shell UCNPs stays behind the expectations compared to their bulk material (being at least μm-sized particles). The core-shell structures are not clearly separated from each other, which is a topic in literature. Instead, there is a transition layer between the core and the shell structure, which relates to the migration of the dopants within the host lattice during the synthesis. The ion migration has been examined by time-resolved laser spectroscopy and the interlanthanoid resonance energy transfer (LRET) in the two different host lattices from above. The results are presented in two publications, which dealt with core-shell-shell structured nanoparticles. The core is doped with the LRET-acceptor (either Nd3+ or Pr3+). The intermediate shell serves as an insulation shell of pure host lattice material, whose shell thickness has been varied within one set of samples having the same composition, so that the spatial separation of LRET-acceptor and -donor changes. The outer shell with the same host lattice is doped with the LRET-donor (Eu3+). The effect of the increasing insulation shell thickness is significant, although the LRET cannot be suppressed completely. Next to the Ln(III) migration within a host lattice, various phase transfer reactions were investigated in order to subsequently perform surface modifications for bioapplications. One result out of this research has been published using a promising ligand, that equips the UCNP with bio-modifiable groups and has good potential for bio-medical applications. This particular ligand mimics natural occurring mechanisms of mussel protein adhesion and of blood coagulation, which is why the UCNPs are encapsulated very effectively. At the same time, bio-functional groups are introduced. In a proof-of-concept, the encapsulated UCNP has been coupled successfully with a dye (which is representative for a biomarker) and the system's photoluminescence properties have been investigated.}, language = {en} } @phdthesis{Flatken2022, author = {Flatken, Marion A.}, title = {The early stages of halide perovskites thin film formation}, doi = {10.25932/publishup-55259}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-552599}, school = {Universit{\"a}t Potsdam}, pages = {VI, 144}, year = {2022}, abstract = {As climate change worsens, there is a growing urgency to promote renewable energies and improve their accessibility to society. Here, solar energy harvesting is of particular importance. Currently, metal halide perovskite (MHP) solar cells are indispensable in future solar energy generation research. MHPs are crystalline semiconductors increasingly relevant as low-cost, high-performance materials for optoelectronics. Their processing from solution at low temperature enables easy fabrication of thin film elements, encompassing solar cells and light-emitting diodes or photodetectors. Understanding the coordination chemistry of MHPs in their precursor solution would allow control over the thin film crystallization, the material properties and the final device performance. In this work, we elaborate on the key parameters to manipulate the precursor solution with the long-term objective of enabling systematic process control. We focus on the nanostructural characterization of the initial arrangements of MHPs in the precursor solutions. Small-angle scattering is particularly well suited for measuring nanoparticles in solution. This technique proved to be valuable for the direct analyzes of perovskite precursor solutions in standard processing concentrations without causing radiation damage. We gain insights into the chemical nature of widely used precursor structures such as methylammonium lead iodide (MAPbI3), presenting first insights into the complex arrangements and interaction within this precursor state. Furthermore, we transfer the preceding results to other more complex perovskite precursors. The influence of compositional engineering is investigated using the addition of alkali cations as an example. As a result, we propose a detailed working mechanism on how the alkali cations suppress the formation of intermediate phases and improve the quality of the crystalline thin film. In addition, we investigate the crystallization process of a tin-based perovskite composition (FASnI3) under the influence of fluoride chemistry. We prove that the frequently used additive, tin fluoride (SnF2), selectively binds undesired oxidized tin (Sn(IV)) in the precursor solution. This prevents its incorporation into the actual crystal structure and thus reduces the defect density of the material. Furthermore, SnF2 leads to a more homogeneous crystal growth process, which results in improved crystal quality of the thin film material. In total, this study provides a detailed characterization of the complex system of perovskite precursor chemistry. We thereby cover relevant parameters for future MHP solar cell process control, such as (I) the environmental impact based on concentration and temperature (II) the addition of counter ions to reduce the diffuse layer surrounding the precursor nanostructures and (III) the targeted use of additives to eliminate unwanted components selectively and to ensure a more homogeneous crystal growth.}, language = {en} } @phdthesis{Kossmann2021, author = {Kossmann, Janina}, title = {Controlled condensation to functional materials - synergetic effect of nitrogen content and pore structure}, doi = {10.25932/publishup-53693}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-536935}, school = {Universit{\"a}t Potsdam}, pages = {vi, 148}, year = {2021}, abstract = {The development and optimization of carbonaceous materials is of great interest for several applications including gas sorption, electrochemical storage and conversion, or heterogeneous catalysis. In this thesis, the exploration and optimization of nitrogen containing carbonaceous materials by direct condensation of smart chosen, molecular precursors will be presented. As suggested with the concept of noble carbons, the choice of a stable, nitrogen-containing precursor will lead to an even more stable, nitrogen doped carbonaceous material with a controlled structure and electronic properties. Molecules fulfilling this requirement are for example nucleobases. The direct condensation of nucleobases leads to highly nitrogen containing carbonaceous materials without any further post or pretreatment. By using salt melt templating, pore structure adjustment is possible without the use of hazardous or toxic reagents and the template can be reused. Using these simple tools, the synergetic effect of the pore structure and nitrogen content of the materials can be explored. Within this thesis, the influence of the condensation parameters will be correlated to the structure and performance of the materials. First, the influence of the condensation temperature to the porosity and nitrogen content of guanine will be discussed and the exploration of highly CO2 selective structural pores in C1N1 materials will be shown. Further tuning the pore structure of the materials by salt melt templating will be then explored, the potential of the prepared materials as heterogeneous catalysts and their basic catalytic strength will be correlated to their nitrogen content and pore morphology. A similar approach is used to explore the water sorption behavior of uric acid derived carbonaceous materials as potential sorbents for heat transformation applications. Changes in maximum water uptake and hydrophilicity of the prepared materials will be correlated to the nitrogen content and pore architecture. Due to the high thermal stability, porosity, and nitrogen content of ionic liquid derived nitrogen doped carbonaceous materials, a simple impregnation and calcination route can be conducted to obtain copper nano cluster decorated nitrogen-doped carbonaceous materials. The activity as catalyst for the oxygen reduction reaction of the obtained materials will be shown and structure performance relations are discussed. In conclusion, the versatility of nitrogen doped carbonaceous materials with a nitrogen to carbon ratio of up to one will be shown. The possibility to tune the pore structure as well as the nitrogen content by using a simple procedure including salt melt templating as well as the use of molecular precursors and their effect on the performance will be discussed.}, language = {en} } @phdthesis{Kaergell2020, author = {K{\"a}rgell, Martin}, title = {Layer formation from perovskite nanoparticles with tunable optical and electronic properties}, doi = {10.25932/publishup-47566}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-475667}, school = {Universit{\"a}t Potsdam}, pages = {ix, 233}, year = {2020}, abstract = {Hybrid organic-inorganic perovskites have attracted attention in recent years, caused by the incomparable increase in efficiency in energy convergence, which implies the application as an absorber material for solar cells. A disadvantage of these materials is, among others, the instability to moisture and UV-radiation. One possible solution for these problems is the reduction of the size towards the nano world. With that nanosized perovskites are showing superior stability in comparison to e.g. perovskite layers. Additionally to this the nanosize even enables stable perovskite structures, which could not be achieved otherwise at room temperature. This thesis is separated into two major parts. The separation is done by the composition and the band gap of the material and at the same time the shape and size of the nanoparticles. Here the division is made by the methylammonium lead tribromide nanoplatelets and the caesium lead triiodide nanocubes. The first part is focusing on the hybrid organic-inorganic perovskite (methylammonium lead tribromide) nanoplatelets with a band gap of 2.35 eV and their thermal behaviour. Due to the challenging character of this material, several analysis methods are used to investigate the sub nano and nanostructures under the influence of temperature. As a result, a shift of phase-transition temperatures towards higher temperatures is observed. This unusual behaviour can be explained by the ligand, which is incorporated in the perovskite outer structure and adds phase-stability into the system. The second part of this thesis is focusing on the inorganic caesium lead triiodide nanocubes with a band gap of 1.83 eV. These nanocrystals are first investigated and compared by TEM, XRD and other optical methods. Within these methods, a cuboid and orthorhombic structure are revealed instead of the in literature described cubic shape and structure. Furthermore, these cuboids are investigated towards their self-assembly on a substrate. Here a high degree in self-assembly is shown. As a next step, the ligands of the nanocuboids are exchanged against other ligands to increase the charge carrier mobility. This is further investigated by the above-mentioned methods. The last section is dealing with the enhancement of the CsPbI3 structure, by incorporating potassium in the crystal structure. The results are suggesting here an increase in stability.}, language = {en} } @phdthesis{Menski2019, author = {Menski, Antonia Isabell}, title = {Europium als strukturelle Sonde zur Analyse neuartiger Materialien}, doi = {10.25932/publishup-42714}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-427141}, school = {Universit{\"a}t Potsdam}, pages = {181}, year = {2019}, abstract = {Im Rahmen dieser Arbeit wird anhand von neuartigen Materialien das Potential der Europium-Lumineszenz f{\"u}r die strukturelle Analyse dargestellt. Bei diesen Materialien handelt es sich zum einen um Nanopartikel mit Matrizes aus mehreren Metall-Mischoxiden und Dotierungen durch die Sonde Europium und zum anderen um Metallorganische Netzwerke (MOFs), die mit Neodym , Samarium- und Europium-Ionen beladen sind. Die Synthese der aus der Kombination von Metalloxiden enthaltenen Nanopartikel ist unter milden Bedingungen mithilfe von speziell daf{\"u}r hergestellten Reagenzien erfolgt und hat zu sehr kleinen, amorphen Nanopartikeln gef{\"u}hrt. Durch eine nachfolgende Temperaturbehandlung hat sich die Kristallinit{\"a}t erh{\"o}ht. Damit verbunden haben sich auch die Kristallstruktur sowie die Position des Dotanden Europium ver{\"a}ndert. W{\"a}hrend die etablierte Methode der R{\"o}ntgendiffraktometrie einen Blick auf das Kristallgitter als Gesamtes erm{\"o}glicht, so trifft die Lumineszenz des Europiums durch die Sichtbarkeit einzelner Stark-Aufspaltungen Aussagen {\"u}ber dessen lokale Symmetrien. Die Symmetrie wird durch Sauerstofffehlstellen ver{\"a}ndert, welche die Sauerstoffleitf{\"a}higkeit der Nanopartikel beeinflussen. Diese ist f{\"u}r die Anwendung als Katalysatoren in industriellen Prozessen und ebenso als Sensoren und Therapeutika in biologischen Systemen von Bedeutung. Zur ersten katalytischen Charakterisierung werden die Proben mittels Temperatur-programmierter Reduktion untersucht. Des Weiteren werden die Mischoxid-Nanopartikel auch hinsichtlich ihrer Verwendbarkeit als Matrix in Aufkonversionsprozessen untersucht. Die Metallorganischen Netzwerke eignen sich aufgrund ihrer mikropor{\"o}sen Struktur f{\"u}r Anwendungen in der Speicherung gleichermaßen von Nutzgasen wie auch von Schadstoffen. Ebenfalls ist eine biologische Anwendung denkbar, die insbesondere den Bereich der drug delivery-Reagenzien betrifft. Erfolgt in die mikropor{\"o}sen Strukturen der Metallorganischen Netzwerke die Einlagerung von Lanthanoid-Ionen, so k{\"o}nnen diese bei der entsprechenden Kombination als Weißlicht-Emittierer fungieren. Dabei ist neben den Verh{\"a}ltnissen zwischen den Lanthanoid-Ionen auch die genaue Position innerhalb des Netzwerks sowie die Distanz zu anderen Ionen von Interesse. Zur Untersuchung dieser Fragestellungen wird die Umgebungssensitivit{\"a}t der Europium-Lumineszenz ausgenutzt. Die auf diese Weise festgestellte Formiat-Bildung h{\"a}ngt von zahlreichen Parametern ab. Insgesamt stellt sich die im Rahmen dieser Arbeit verwendete Methodik des Einsatzes von Europium als strukturelle Sonde in h{\"o}chstem Maße vielseitig dar und zeigt seine gr{\"o}ßte St{\"a}rke in der Kombination mit weiteren Methoden der Strukturanalytik. Die auf diese Weise genauestens charakterisierten neuartigen Materialien k{\"o}nnen nun gezielt und anwendungsfokussiert weiterentwickelt werden.}, language = {de} } @phdthesis{Ilic2020, author = {Ilic, Ivan}, title = {Design of sustainable cathodes for Li-ion batteries}, doi = {10.25932/publishup-48368}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-483689}, school = {Universit{\"a}t Potsdam}, pages = {iv, 154}, year = {2020}, abstract = {In recent years people have realised non-renewability of our modern society which relays on spending huge amounts of energy mostly produced from fosil fuels, such as oil and coal, and the shift towards more sustainable energy sources has started. However, sustainable sources of energy, such as wind-, solar- and hydro-energy, produce primarily electrical energy and can not just be poured in canister like many fosil fuels, creating necessity for rechragable batteries. However, modern Li-ion batteries are made from toxic heavy metals and sustainable alternatives are needed. Here we show that naturally abundant catecholic and guaiacyl groups can be utilised to replace heavy metals in Li-ion batteries. Foremost vanillin, a naturally occurring food additive that can be sustainably synthesised from industrial biowaste, lignin, was utilised to synthesise materials that showed extraordinary performance as cathodes in Li-ion batteries. Furthermore, behaviour of catecholic and guiacyl groups in Li-ion system was compared, confirming usability of guiacayl containing biopolymers as cathodes in Li-ion batteries. Lastly, naturally occurring polyphenol, tannic acid, was incorporated in fully bioderived hybrid material that shows performance comparable to commercial Li-ion batteries and good stability. This thesis presents an important advancement in understanding of biowaste derived cathode materials for Li-ion batteries. Further research should be conducted to better understand behaviour of guaiacyl groups during Li-ion battery cycling. Lastly, challenges of incorporation of lignin, an industrial biowaste, have to be addressed and lignin should be incorporated as a cathode material in Li-ion batteries.}, language = {en} } @phdthesis{MartinezGuajardo2024, author = {Mart{\´i}nez Guajardo, Alejandro}, title = {New zwitterionic polymers for antifouling applications}, doi = {10.25932/publishup-62682}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:517-opus4-626820}, school = {Universit{\"a}t Potsdam}, pages = {XIX, 145}, year = {2024}, abstract = {The remarkable antifouling properties of zwitterionic polymers in controlled environments are often counteracted by their delicate mechanical stability. In order to improve the mechanical stabilities of zwitterionic hydrogels, the effect of increased crosslinker densities was thus explored. In a first approach, terpolymers of zwitterionic monomer 3-[N -2(methacryloyloxy)ethyl-N,N-dimethyl]ammonio propane-1-sulfonate (SPE), hydrophobic monomer butyl methacrylate (BMA), and photo-crosslinker 2-(4-benzoylphenoxy)ethyl methacrylate (BPEMA) were synthesized. Thin hydrogel coatings of the copolymers were then produced and photo-crosslinked. Studies of the swollen hydrogel films showed that not only the mechanical stability but also, unexpectedly, the antifouling properties were improved by the presence of hydrophobic BMA units in the terpolymers. Based on the positive results shown by the amphiphilic terpolymers and in order to further test the impact that hydrophobicity has on both the antifouling properties of zwitterionic hydrogels and on their mechanical stability, a new amphiphilic zwitterionic methacrylic monomer, 3-((2-(methacryloyloxy)hexyl)dimethylammonio)propane-1-sulfonate (M1), was synthesized in good yields in a multistep synthesis. Homopolymers of M1 were obtained by free-radical polymerization. Similarly, terpolymers of M1, zwitterionic monomer SPE, and photo-crosslinker BPEMA were synthesized by free-radical copolymerization and thoroughly characterized, including its solubilities in selected solvents. Also, a new family of vinyl amide zwitterionic monomomers, namely 3-(dimethyl(2-(N -vinylacetamido)ethyl)ammonio)propane-1-sulfonate (M2), 4-(dimethyl(2-(N-vinylacetamido)ethyl)ammonio)butane-1-sulfonate (M3), and 3-(dimethyl(2-(N-vinylacetamido)ethyl)ammonio)propyl sulfate (M4), together with the new photo-crosslinker 4-benzoyl-N-vinylbenzamide (M5) that is well-suited for copolymerization with vinylamides, are introduced within the scope of the present work. The monomers are synthesized with good yields developing a multistep synthesis. Homopolymers of the new vinyl amide zwitterionic monomers are obtained by free-radical polymerization and thoroughly characterized. From the solubility tests, it is remarkable that the homopolymers produced are fully soluble in water, evidence of their high hydrophilicity. Copolymerization of the vinyl amide zwitterionic monomers, M2, M3, and M4 with the vinyl amide photo-crosslinker M5 proved to require very specific polymerization conditions. Nevertheless, copolymers were successfully obtained by free-radical copolymerization under appropriate conditions. Moreover, in an attempt to mitigate the intrinsic hydrophobicity introduced in the copolymers by the photo-crosslinkers, and based on the proven affinity of quaternized diallylamines to copolymerize with vinyl amides, a new quaternized diallylamine sulfobetaine photo-crosslinker 3-(diallyl(2-(4-benzoylphenoxy)ethyl)ammonio)propane-1-sulfonate (M6) is synthesized. However, despite a priori promising copolymerization suitability, copolymerization with the vinyl amide zwitterionic monomers could not be achieved.}, language = {en} } @phdthesis{Heinke2018, author = {Heinke, David}, title = {Biokompatible superparamagnetische Nanopartikel}, publisher = {Infinite Science Publishing}, address = {L{\"u}beck}, isbn = {978-3-945954-45-4}, pages = {142}, year = {2018}, abstract = {Magnetische Eisenoxidnanopartikel werden bereits seit geraumer Zeit erfolgreich als MRT-Kontrastmittel in der klinischen Bildgebung eingesetzt. Durch Optimierung der magnetischen Eigenschaften der Nanopartikel kann die Aussagekraft von MR-Aufnahmen verbessert und somit der diagnostische Wert einer MR-Anwendung weiter erh{\"o}ht werden. Neben der Verbesserung bestehender Verfahren wird die bildgebende Diagnostik ebenso durch die Entwicklung neuer Verfahren, wie dem Magnetic Particle Imaging, vorangetrieben. Da hierbei das Messsignal von den magnetischen Nanopartikeln selbst erzeugt wird, birgt das MPI einen enormen Vorteil hinsichtlich der Sensitivit{\"a}t bei gleichzeitig hoher zeitlicher und r{\"a}umlicher Aufl{\"o}sung. Da es aktuell jedoch keinen kommerziell vertriebenen in vivo-tauglichen MPI-Tracer gibt, besteht ein dringender Bedarf an geeigneten innovativen Tracermaterialien. Daraus resultierte die Motivation dieser Arbeit biokompatible und superparamagnetische Eisenoxidnanopartikel f{\"u}r den Einsatz als in vivo-Diagnostikum insbesondere im Magnetic Particle Imaging zu entwickeln. Auch wenn der Fokus auf der Tracerentwicklung f{\"u}r das MPI lag, wurde ebenso die MR-Performance bewertet, da geeignete Partikel somit alternativ oder zus{\"a}tzlich als MR-Kontrastmittel mit verbesserten Kontrasteigenschaften eingesetzt werden k{\"o}nnten. Die Synthese der Eisenoxidnanopartikel erfolgte {\"u}ber die partielle Oxidation von gef{\"a}lltem Eisen(II)-hydroxid und Green Rust sowie eine diffusionskontrollierte Kopr{\"a}zipitation in einem Hydrogel. Mit der partiellen Oxidation von Eisen(II)-hydroxid und Green Rust konnten erfolgreich biokompatible und {\"u}ber lange Zeit stabile Eisenoxidnanopartikel synthetisiert werden. Zudem wurden geeignete Methoden zur Formulierung und Sterilisierung etabliert, wodurch zahlreiche Voraussetzungen f{\"u}r eine Anwendung als in vivo-Diagnostikum geschaffen wurden. Weiterhin ist auf Grundlage der MPS-Performance eine hervorragende Eignung dieser Partikel als MPI-Tracer zu erwarten, wodurch die Weiterentwicklung der MPI-Technologie maßgeblich vorangetrieben werden k{\"o}nnte. Die Bestimmung der NMR-Relaxivit{\"a}ten sowie ein initialer in vivo-Versuch zeigten zudem das große Potential der formulierten Nanopartikelsuspensionen als MRT-Kontrastmittel. Die Modifizierung der Partikeloberfl{\"a}che erm{\"o}glicht ferner die Herstellung zielgerichteter Nanopartikel sowie die Markierung von Zellen, wodurch das m{\"o}gliche Anwendungsspektrum maßgeblich erweitert wurde. Im zweiten Teil wurden Partikel durch eine diffusionskontrollierte Kopr{\"a}zipitation im Hydrogel, wobei es sich um eine bioinspirierte Modifikation der klassischen Kopr{\"a}zipitation handelt, synthetisiert, wodurch Partikel mit einer durchschnittlichen Kristallitgr{\"o}ße von 24 nm generiert werden konnten. Die Bestimmung der MPS- und MR-Performance elektrostatisch stabilisierter Partikel ergab vielversprechende Resultate. In Vorbereitung auf die Entwicklung eines in vivo-Diagnostikums wurden die Partikel anschließend erfolgreich sterisch stabilisiert, wodurch der kolloidale Zustand in MilliQ-Wasser {\"u}ber lange Zeit aufrechterhalten werden konnte. Durch Zentrifugation konnten die Partikel zudem erfolgreich in verschiedene Gr{\"o}ßenfraktionen aufgetrennt werden. Dies erm{\"o}glichte die Bestimmung der idealen Aggregatgr{\"o}ße dieses Partikelsystems in Bezug auf die MPS-Performance.}, language = {de} }