@article{SerranoMunozUlbrichtFritschetal.2021, author = {Serrano-Munoz, Itziar and Ulbricht, Alexander and Fritsch, Tobias and Mishurova, Tatiana and Kromm, Arne and Hofmann, Michael and Wimpory, Robert C. and Evans, Alexander and Bruno, Giovanni}, title = {Scanning manufacturing parameters determining the residual stress state in LPBF IN718 small parts}, series = {Advanced engineering materials}, volume = {23}, journal = {Advanced engineering materials}, number = {7}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1438-1656}, doi = {10.1002/adem.202100158}, pages = {13}, year = {2021}, abstract = {The influence of scan strategy on the residual stress (RS) state of an as-built IN718 alloy produced by means of laser powder bed fusion (LPBF) is investigated. Two scan vector rotations (90 degrees-alternation and 67 degrees-rotation), each produced following two different scan vector lengths (long and short), are used to manufacture four rectangular prisms. Neutron diffraction (ND) and laboratory X-ray diffraction (XRD) techniques are used to map the bulk and surface RS state, respectively. The distortion induced upon removal from the baseplate is measured via profilometry. XRD measurements show that the two long scan vector strategies lead to higher RS when compared with the equivalent short scan vector strategies. Also, the 67 degrees-rotation strategies generate lower RS than their 90 degrees-alternation counterparts. Due to the lack of reliable stress-free d0 references, the ND results are analyzed using von Mises stress. In general, ND results show significant RS spatial non-uniformity. A comparison between ND and distortion results indicates that the RS component parallel to the building direction (Z-axis) has a predominant role in the Z-displacement. The use of a stress balance scheme allows to discuss the d0 variability along the length of the specimens, as well as examine the absolute RS state.}, language = {en} } @article{SprengelUlbrichtEvansetal.2021, author = {Sprengel, Maximilian and Ulbricht, Alexander and Evans, Alexander and Kromm, Arne and Sommer, Konstantin and Werner, Tiago and Kelleher, Joanne and Bruno, Giovanni and Kannengießer, Thomas}, title = {Towards the optimization of post-laser powder bed fusion stress-relieve treatments of stainless steel 316L}, series = {Metallurgical and materials transactions. A, Physical metallurgy and materials science}, volume = {52}, journal = {Metallurgical and materials transactions. A, Physical metallurgy and materials science}, number = {12}, publisher = {Springer}, address = {Boston}, issn = {1073-5623}, doi = {10.1007/s11661-021-06472-6}, pages = {5342 -- 5356}, year = {2021}, abstract = {The use of post-processing heat treatments is often considered a necessary approach to relax high-magnitude residual stresses (RS) formed during the layerwise additive manufacturing laser powder bed fusion (LPBF). In this work, three heat treatment strategies using temperatures of 450 degrees C, 800 degrees C, and 900 degrees C are applied to austenitic stainless steel 316L samples manufactured by LPBF. These temperatures encompass the suggested lower and upper bounds of heat treatment temperatures of conventionally processed 316L. The relaxation of the RS is characterized by neutron diffraction (ND), and the associated changes of the microstructure are analyzed using electron backscattered diffraction (EBSD) and scanning electron microscopy (SEM). The lower bound heat treatment variant of 450 degrees C for 4 hours exhibited high tensile and compressive RS. When applying subsequent heat treatments, we show that stress gradients are still observed after applying 800 degrees C for 1 hour but almost completely vanish when applying 900 degrees C for 1 hour. The observed near complete relaxation of the RS appears to be closely related to the evolution of the characteristic subgrain solidification cellular microstructure.}, language = {en} } @article{SchroederEvansMishurovaetal.2021, author = {Schr{\"o}der, Jakob and Evans, Alexander and Mishurova, Tatiana and Ulbricht, Alexander and Sprengel, Maximilian and Serrano-Munoz, Itziar and Fritsch, Tobias and Kromm, Arne and Kannengießer, Thomas and Bruno, Giovanni}, title = {Diffraction-based residual stress characterization in laser additive manufacturing of metals}, series = {Metals : open access journal}, volume = {11}, journal = {Metals : open access journal}, number = {11}, publisher = {MDPI}, address = {Basel}, issn = {2075-4701}, doi = {10.3390/met11111830}, pages = {34}, year = {2021}, abstract = {Laser-based additive manufacturing methods allow the production of complex metal structures within a single manufacturing step. However, the localized heat input and the layer-wise manufacturing manner give rise to large thermal gradients. Therefore, large internal stress (IS) during the process (and consequently residual stress (RS) at the end of production) is generated within the parts. This IS or RS can either lead to distortion or cracking during fabrication or in-service part failure, respectively. With this in view, the knowledge on the magnitude and spatial distribution of RS is important to develop strategies for its mitigation. Specifically, diffraction-based methods allow the spatial resolved determination of RS in a non-destructive fashion. In this review, common diffraction-based methods to determine RS in laser-based additive manufactured parts are presented. In fact, the unique microstructures and textures associated to laser-based additive manufacturing processes pose metrological challenges. Based on the literature review, it is recommended to (a) use mechanically relaxed samples measured in several orientations as appropriate strain-free lattice spacing, instead of powder, (b) consider that an appropriate grain-interaction model to calculate diffraction-elastic constants is both material- and texture-dependent and may differ from the conventionally manufactured variant. Further metrological challenges are critically reviewed and future demands in this research field are discussed.}, language = {en} } @article{SerranoMunozFritschMishurovaetal.2020, author = {Serrano-Munoz, Itziar and Fritsch, Tobias and Mishurova, Tatiana and Trofimov, Anton and Apel, Daniel and Ulbricht, Alexander and Kromm, Arne and Hesse, Rene and Evans, Alexander and Bruno, Giovanni}, title = {On the interplay of microstructure and residual stress in LPBF IN718}, series = {Journal of materials science}, volume = {56}, journal = {Journal of materials science}, number = {9}, publisher = {Springer}, address = {New York}, issn = {0022-2461}, doi = {10.1007/s10853-020-05553-y}, pages = {5845 -- 5867}, year = {2020}, abstract = {The relationship between residual stresses and microstructure associated with a laser powder bed fusion (LPBF) IN718 alloy has been investigated on specimens produced with three different scanning strategies (unidirectional Y-scan, 90 degrees XY-scan, and 67 degrees Rot-scan). Synchrotron X-ray energy-dispersive diffraction (EDXRD) combined with optical profilometry was used to study residual stress (RS) distribution and distortion upon removal of the specimens from the baseplate. The microstructural characterization of both the bulk and the near-surface regions was conducted using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). On the top surfaces of the specimens, the highest RS values are observed in the Y-scan specimen and the lowest in the Rot-scan specimen, while the tendency is inversed on the side lateral surfaces. A considerable amount of RS remains in the specimens after their removal from the baseplate, especially in the Y- and Z-direction (short specimen dimension and building direction (BD), respectively). The distortion measured on the top surface following baseplate thinning and subsequent removal is mainly attributed to the amount of RS released in the build direction. Importantly, it is observed that the additive manufacturing microstructures challenge the use of classic theoretical models for the calculation of diffraction elastic constants (DEC) required for diffraction-based RS analysis. It is found that when the Reuss model is used for the calculation of RS for different crystal planes, as opposed to the conventionally used Kroner model, the results exhibit lower scatter. This is discussed in context of experimental measurements of DEC available in the literature for conventional and additively manufactured Ni-base alloys.}, language = {en} } @article{MishurovaSydowThiedeetal.2020, author = {Mishurova, Tatiana and Sydow, Benjamin and Thiede, Tobias and Sizova, Irina and Ulbricht, Alexander and Bambach, Markus and Bruno, Giovanni}, title = {Residual stress and microstructure of a Ti-6Al-4V Wire Arc Additive Manufacturing hybrid demonstrator}, series = {Metals}, volume = {10}, journal = {Metals}, number = {6}, publisher = {MDPI}, address = {Basel}, issn = {2075-4701}, doi = {10.3390/met10060701}, pages = {15}, year = {2020}, abstract = {Wire Arc Additive Manufacturing (WAAM) features high deposition rates and, thus, allows production of large components that are relevant for aerospace applications. However, a lot of aerospace parts are currently produced by forging or machining alone to ensure fast production and to obtain good mechanical properties; the use of these conventional process routes causes high tooling and material costs. A hybrid approach (a combination of forging and WAAM) allows making production more efficient. In this fashion, further structural or functional features can be built in any direction without using additional tools for every part. By using a combination of forging basic geometries with one tool set and adding the functional features by means of WAAM, the tool costs and material waste can be reduced compared to either completely forged or machined parts. One of the factors influencing the structural integrity of additively manufactured parts are (high) residual stresses, generated during the build process. In this study, the triaxial residual stress profiles in a hybrid WAAM part are reported, as determined by neutron diffraction. The analysis is complemented by microstructural investigations, showing a gradient of microstructure (shape and size of grains) along the part height. The highest residual stresses were found in the transition zone (between WAAM and forged part). The total stress range showed to be lower than expected for WAAM components. This could be explained by the thermal history of the component.}, language = {en} } @article{OsterFritschUlbrichtetal.2022, author = {Oster, Simon and Fritsch, Tobias and Ulbricht, Alexander and Mohr, Gunther and Bruno, Giovanni and Maierhofer, Christiane and Altenburg, Simon}, title = {On the registration of thermographic in situ monitoring data and computed tomography reference data in the scope of defect prediction in laser powder bed fusion}, series = {Metals : open access journal}, volume = {12}, journal = {Metals : open access journal}, number = {6}, publisher = {MDPI}, address = {Basel}, issn = {2075-4701}, doi = {10.3390/met12060947}, pages = {21}, year = {2022}, abstract = {The detection of internal irregularities is crucial for quality assessment in metal-based additive manufacturing (AM) technologies such as laser powder bed fusion (L-PBF). The utilization of in-process thermography as an in situ monitoring tool in combination with post-process X-ray micro computed tomography (XCT) as a reference technique has shown great potential for this aim. Due to the small irregularity dimensions, a precise registration of the datasets is necessary as a requirement for correlation. In this study, the registration of thermography and XCT reference datasets of a cylindric specimen containing keyhole pores is carried out for the development of a porosity prediction model. The considered datasets show variations in shape, data type and dimensionality, especially due to shrinkage and material elevation effects present in the manufactured part. Since the resulting deformations are challenging for registration, a novel preprocessing methodology is introduced that involves an adaptive volume adjustment algorithm which is based on the porosity distribution in the specimen. Thus, the implementation of a simple three-dimensional image-to-image registration is enabled. The results demonstrate the influence of the part deformation on the resulting porosity location and the importance of registration in terms of irregularity prediction.}, language = {en} } @article{UlbrichtMohrAltenburgetal.2021, author = {Ulbricht, Alexander and Mohr, Gunther and Altenburg, Simon J. and Oster, Simon and Maierhofer, Christiane and Bruno, Giovanni}, title = {Can potential defects in LPBF be healed from the laser exposure of subsequent layers?}, series = {Metals : open access journal}, volume = {11}, journal = {Metals : open access journal}, number = {7}, publisher = {MDPI}, address = {Basel}, issn = {2075-4701}, doi = {10.3390/met11071012}, pages = {14}, year = {2021}, abstract = {Additive manufacturing (AM) of metals and in particular laser powder bed fusion (LPBF) enables a degree of freedom in design unparalleled by conventional subtractive methods. To ensure that the designed precision is matched by the produced LPBF parts, a full understanding of the interaction between the laser and the feedstock powder is needed. It has been shown that the laser also melts subjacent layers of material underneath. This effect plays a key role when designing small cavities or overhanging structures, because, in these cases, the material underneath is feed-stock powder. In this study, we quantify the extension of the melt pool during laser illumination of powder layers and the defect spatial distribution in a cylindrical specimen. During the LPBF process, several layers were intentionally not exposed to the laser beam at various locations, while the build process was monitored by thermography and optical tomography. The cylinder was finally scanned by X-ray computed tomography (XCT). To correlate the positions of the unmolten layers in the part, a staircase was manufactured around the cylinder for easier registration. The results show that healing among layers occurs if a scan strategy is applied, where the orientation of the hatches is changed for each subsequent layer. They also show that small pores and surface roughness of solidified material below a thick layer of unmolten material (>200 mu m) serve as seeding points for larger voids. The orientation of the first two layers fully exposed after a thick layer of unmolten powder shapes the orientation of these voids, created by a lack of fusion.}, language = {en} }