@article{BhattacharyyaBalischewskiSperlichetal.2023,
  author    = {Bhattacharyya, Biswajit and Balischewski, Christian and Sperlich, Eric and G{\"u}nter, Christina and Mies, Stefan and Kelling, Alexandra and Taubert, Andreas},
  title     = {N-Butyl Pyridinium Diiodido Argentate(I)},
  series = {Advanced materials interfaces},
  volume    = {10},
  journal   = {Advanced materials interfaces},
  number    = {12},
  publisher = {Wiley},
  address   = {Hoboken},
  issn      = {2196-7350},
  doi       = {10.1002/admi.202202363},
  pages     = {7},
  year      = {2023},
  abstract  = {A new solid-state material, N-butyl pyridinium diiodido argentate(I), is synthesized using a simple and effective one-pot approach. In the solid state, the compound exhibits 1D ([AgI2](-))(n) chains that are stabilized by the N-butyl pyridinium cation. The 1D structure is further manifested by the formation of long, needle-like crystals, as revealed from electron microscopy. As the general composition is derived from metal halide-based ionic liquids, the compound has a low melting point of 100-101 degrees C, as confirmed by differential scanning calorimetry. Most importantly, the compound has a conductivity of 10(-6) S cm(-1) at room temperature. At higher temperatures the conductivity increases and reaches to 10(-4 )S cm(-1) at 70 degrees C. In contrast to AgI, however, the current material has a highly anisotropic 1D arrangement of the ionic domains. This provides direct and tuneable access to fast and anisotropic ionic conduction. The material is thus a significant step forward beyond current ion conductors and a highly promising prototype for the rational design of highly conductive ionic solid-state conductors for battery or solar cell applications.},
  language  = {en}
}
@article{AdesinaBlockGuenteretal.2023,
  author    = {Adesina, Morenike O. and Block, Inga and G{\"u}nter, Christina and Unuabonah, Emmanuel Iyayi and Taubert, Andreas},
  title     = {Efficient Removal of Tetracycline and Bisphenol A from Water with a New Hybrid Clay/TiO2 Composite},
  series = {ACS Omega},
  volume    = {8},
  journal   = {ACS Omega},
  number    = {24},
  publisher = {American Chemical Society},
  address   = {Washington},
  issn      = {2470-1343},
  doi       = {10.1021/acsomega.3c00184},
  pages     = {21594 -- 21604},
  year      = {2023},
  abstract  = {New TiO2 hybrid composites were prepared fromkaolinclay, predried and carbonized biomass, and titanium tetraisopropoxideand explored for tetracycline (TET) and bisphenol A (BPA) removalfrom water. Overall, the removal rate is 84\% for TET and 51\% for BPA.The maximum adsorption capacities (q (m))are 30 and 23 mg/g for TET and BPA, respectively. These capacitiesare far greater than those obtained for unmodified TiO2. Increasing the ionic strength of the solution does not change theadsorption capacity of the adsorbent. pH changes only slightly changeBPA adsorption, while a pH > 7 significantly reduces the adsorptionof TET on the material. The Brouers-Sotolongo fractal modelbest describes the kinetic data for both TET and BPA adsorption, predictingthat the adsorption process occurs via a complex mechanism involvingvarious forces of attraction. Temkin and Freundlich isotherms, whichbest fit the equilibrium adsorption data for TET and BPA, respectively,suggest that adsorption sites are heterogeneous in nature. Overall,the composite materials are much more effective for TET removal fromaqueous solution than for BPA. This phenomenon is assigned to a differencein the TET/adsorbent interactions vs the BPA/adsorbent interactions:the decisive factor appears to be favorable electrostatic interactionsfor TET yielding a more effective TET removal.},
  language  = {en}
}