@article{GarnierLaschewsky2006, author = {Garnier, Sebastien and Laschewsky, Andre}, title = {Non-ionic amphiphilic block copolymers by RAFT-polymerization and their self-organization}, series = {Colloid and polymer science : official journal of the Kolloid-Gesellschaft}, volume = {284}, journal = {Colloid and polymer science : official journal of the Kolloid-Gesellschaft}, publisher = {Springer}, address = {Berlin}, issn = {0303-402X}, doi = {10.1007/s00396-006-1484-9}, pages = {1243 -- 1254}, year = {2006}, abstract = {Water-soluble, amphiphilic diblock copolymers were synthesized by reversible addition fragmentation chain transfer polymerization. They consist of poly(butyl acrylate) as hydrophobic block with a low glass transition temperature and three different nonionic water-soluble blocks, namely, the classical hydrophilic block poly(dimethylacrylamide), the strongly hydrophilic poly(acryloyloxyethyl methylsulfoxide), and the thermally sensitive poly(N-acryloylpyrrolidine). Aqueous micellar solutions of the block copolymers were prepared and characterized by static and dynamic light scattering analysis (DLS and SLS). No critical micelle concentration could be detected. The micellization was thermodynamically favored, although kinetically slow, exhibiting a marked dependence on the preparation conditions. The polymers formed micelles with a hydrodynamic diameter from 20 to 100 nm, which were stable upon dilution. The micellar size was correlated with the composition of the block copolymers and their overall molar mass. The micelles formed with the two most hydrophilic blocks were particularly stable upon temperature cycles, whereas the thermally sensitive poly(N-acryloylpyrrolidine) block showed a temperature-induced precipitation. According to combined SLS and DLS analysis, the micelles exhibited an elongated shape such as rods or worms. It should be noted that the block copolymers with the most hydrophilic poly(sulfoxide) block formed inverse micelles in certain organic solvents.}, language = {en} } @article{FuechselKlamrothDokicetal.2006, author = {F{\"u}chsel, Gernot and Klamroth, Tillmann and Dokic, Jadranka and Saalfrank, Peter}, title = {On the electronic structure of neutral and ionic azobenzenes and their possible role as surface mounted molecular switches}, series = {The journal of physical chemistry : B, Condensed matter, materials, surfaces, interfaces \& biophysical chemistry}, volume = {110}, journal = {The journal of physical chemistry : B, Condensed matter, materials, surfaces, interfaces \& biophysical chemistry}, number = {33}, publisher = {Soc.}, address = {Washington}, issn = {1520-6106}, doi = {10.1021/jp060969v}, pages = {16337 -- 16345}, year = {2006}, abstract = {We report quantum chemical calculations, mostly based on density functional theory, on azobenzene and substituted azobenzenes as neutral molecules or ions, in ground and excited states. Both the cis and trans configurations are computed as well as the activation energies to transform one isomer into the other and the possible reaction paths and reaction surfaces along the torsion and inversion modes. All calculations are done for the isolated species, but results are discussed in light of recent experiments aiming at the switching of surface mounted azobenzenes by scanning tunneling microscopes.}, language = {en} } @misc{LutzKristenSkrabaniaetal.2006, author = {Lutz, Jean-Francois and Kristen, Juliane and Skrabania, Katja and Laschewsky, Andre}, title = {POLY 14-Synthetic strategies for preparing multicompartment micelles}, series = {Abstracts of papers / American Chemical Society}, volume = {232}, journal = {Abstracts of papers / American Chemical Society}, publisher = {American Chemical Society}, address = {Washington}, isbn = {0-8412-7426-6}, issn = {0065-7727}, pages = {1}, year = {2006}, abstract = {The fabrication of compartmented micellar systems is an exciting new area of research in the field of polymer self-assembly. Multicompartment micelles composed of a water-soluble shell and a segregated hydrophobic core can be obtained via direct aqueous self-assembly of preformed polymeric amphiphiles possessing one hydrophilic segment and two incompatible hydrophobic segments (e.g. hydrocarbon and fluorocarbon blocks). Such macromolecular building-blocks were prepared in the present work principally via reversible addition-fragmentation transfer polymerization (RAFT). Polysoaps or triblock macrosurfactants can be synthesized in high yields by RAFT under relatively straightforward experimental conditions.}, language = {en} } @article{SchmidtNave2006, author = {Schmidt, Bernd and Nave, Stefan}, title = {Stereoselective syntheses of enantiomerically pure 2,5-disubstituted dihydropyrans based on olefin metathesis}, series = {The journal of organic chemistry}, volume = {71}, journal = {The journal of organic chemistry}, number = {19}, publisher = {American Chemical Society}, address = {Washington}, issn = {0022-3263}, doi = {10.1021/jo061190k}, pages = {7364 -- 7369}, year = {2006}, abstract = {A short synthesis of 2,5-disubstituted dihydropyrans starting from D-mannitol as a chiral building block is described. Our synthetic approach combines ruthenium-catalyzed ring closing olefin metathesis and palladium-catalyzed nucleophilic substitution.}, language = {en} } @article{KappBeissenhirtzGeyeretal.2006, author = {Kapp, A. and Beissenhirtz, Moritz Karl and Geyer, F. and Scheller, F. and Viezzoli, Maria Silvia and Lisdat, Fred}, title = {Electrochemical and sensorial behavior of SOD mutants immobilized on gold electrodes in aqueous/organic solvent mixtures}, series = {Electroanalysis : an international journal devoted to fundamental and practical aspects of electroanalysis}, volume = {18}, journal = {Electroanalysis : an international journal devoted to fundamental and practical aspects of electroanalysis}, publisher = {Wiley}, address = {Weinheim}, issn = {1040-0397}, doi = {10.1002/elan.200603620}, pages = {1909 -- 1915}, year = {2006}, abstract = {A cysteine mutant of a monomeric human Cu, Zn-SOD (Glycine 61, Serine 142) has been immobilized directly on gold electrodes using the thiol groups introduced. The electrochemical behavior of the surface confined protein was studied in mixtures of aqueous buffer and DMSO up to an organic solvent content of 60\%. The formal potential was found to be rather independent of the DMSO content. However, half peak width increased and the redoxactive amount clearly decreased with raising DMSO content. In addition, the kinetics of the heterogeneous electron transfer became slower; but still a quasireversible electrochemical conversion of the mutant SOD was feasible. Thus, the electrodes were applied for sensorial superoxide detection. At a potential of +220 mV vs. Ag/AgCl advantage was taken of the partial oxidation reaction of the enzyme. A defined superoxide signal was obtained in solutions up to 40\% DMSO. The sensitivity of the mutant electrodes decreased linearly with the organic solvent content in solution but was still higher compared to conventional cyt.c based sensors. At DMSO concentrations higher than 40\% no sensor response was detected.}, language = {en} } @article{Saalfrank2006, author = {Saalfrank, Peter}, title = {Quantum dynamical approach to ultrafast molecular desorption from surfaces}, series = {Chemical reviews}, volume = {106}, journal = {Chemical reviews}, number = {10}, publisher = {American Chemical Society}, address = {Washington}, issn = {0009-2665}, doi = {10.1021/cr0501691}, pages = {4116 -- 4159}, year = {2006}, language = {en} } @article{NoteKoetzKosmella2006, author = {Note, Carine and Koetz, Joachim and Kosmella, Sabine}, title = {Structural changes in poly(ethyleneimine) modified microemulsion}, series = {Journal of colloid and interface science}, volume = {302}, journal = {Journal of colloid and interface science}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0021-9797}, doi = {10.1016/j.jcis.2006.06.071}, pages = {662 -- 668}, year = {2006}, abstract = {The influence of branched poly(ethyleneimine) on the phase behavior of the system sodium dodecylsulfate/toluene-pentanol (1:1)/water has been studied. The isotropic microemulsions still exist when water is replaced with aqueous solutions of PEI (up to 30\% in weight), but their stability is significantly influenced. From a polymer concentration of 20 wt\%, the polymer enhances the solubilization of water in oil, changes the sign of the spontaneous curvature of the surfactant film, and induces an inversion of the microemulsion type from water-in-oil (L-2) to oil-in-water (L-1), by the formation of a bicontinuous channel. Further investigations show that the addition of polymer in the L-2 phase changes the droplet-droplet interactions as the conductivity drops and the percolation disappears. In the bicontinuous channel, higher viscosities can be detected, as well as a weak percolation followed by a steep increase of the conductivity, which can be related to evident structural changes in the system. DSC measurements allow then to follow the changes of the water properties in the system, from interfacial-water in the L-2 phase to free-water in the sponge-like phase. Finally, all the measurements performed permit to characterize the structural transitions in the system and to understand the role of the added polymer.}, language = {en} } @article{LangeWagnerZentel2006, author = {Lange, Birger and Wagner, J{\"u}rgen and Zentel, Rudolf}, title = {Fabrication of robust high-quality ORMOCER (R) inverse opals}, series = {Macromolecular rapid communications}, volume = {27}, journal = {Macromolecular rapid communications}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1022-1336}, doi = {10.1002/marc.200600429}, pages = {1746 -- 1751}, year = {2006}, abstract = {The nanostructuring of ORMOCER (R) to form inverse opals is described. For this purpose a polymer opal is used as a template and infiltrated with liquid ORMOCER (R). After photopolymerization of the resin the host opal is dissolved in tetrahydrofuran and an ORMOCER (R) inverse opal is obtained. It shows excellent periodicity (by SEM) and optical properties to reveal a high degree of face centered cubic order. This replication process leads to a nanostructured photonic crystal with the outstanding mechanical properties of ORMOCER (R) and high temperature stability up to 350 degrees C.}, language = {en} } @article{TeixeiraBlanzatKoetzetal.2006, author = {Teixeira, C. V. and Blanzat, Muriel and Koetz, Joachim and Rico-Lattes, I. and Brezesinski, Gerald}, title = {In-plane miscibility and mixed bilayer microstructure in mixtures of catanionic glycolipids and zwitterionic phospholipids}, series = {Biochimica et biophysica acta : Biomembranes}, volume = {1758}, journal = {Biochimica et biophysica acta : Biomembranes}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0005-2736}, doi = {10.1016/j.bbamem.2006.05.025}, pages = {1797 -- 1808}, year = {2006}, abstract = {SAXS/WAXS studies were performed in combination with freeze fracture electron microscopy using mixtures of a new Gemini catanionic surfactant (Gem 16-12, formed by two sugar groups bound by a hydrocarbon spacer with 12 carbons and two 16-carbon chains) and the zwitterionic phospholipid 1,2-dipalmitoyl-sn-glycero-3-phosphocholine(DPPC) to establish the phase diagram. Gem 16-12 in water forms bilayers with the same amount of hydration water as DPPC. A frozen interdigitated phase with a low hydration number is observed below room temperature. The kinetics of the formation of this crystalline phase is very slow. Above the chain melting temperature, multilayered vesicles are formed. Mixing with DPPC produces mixed bilayers above the corresponding chain melting temperature. At room temperature, partially lamellar aggregates with local nematic order are observed. Splitting of infinite lamellae into discs is linked to immiscibility in frozen state. The ordering process is always accompanied by dehydration of the system. As a consequence, an unusual order-disorder phase transition upon cooling is observed.}, language = {en} } @article{KozlevcarGolobicStrauch2006, author = {Kozlevcar, Bojan and Golobic, Amalija and Strauch, Peter}, title = {Dynamic pseudo Jahn-Teller distortion in a compressed octahedral CuO6 complex}, series = {Polyhedron : the international journal of inorganic and organometallic chemistry}, volume = {25}, journal = {Polyhedron : the international journal of inorganic and organometallic chemistry}, number = {15}, publisher = {Elsevier}, address = {Oxford}, issn = {0277-5387}, doi = {10.1016/j.poly.2006.04.009}, pages = {2824 -- 2828}, year = {2006}, abstract = {The crystal structure of cis-[Cu(C8H7O3)(2)(H2O)(2)] (115 K data) reveals bidentate vanillinate ions coordinated via methoxy and deprotonated hydroxy oxygen atoms and water molecules in a distorted octahedral CuO6 chromophore. A cis orientation of the ligands enables two non-identical O(methoxy)-Cu-O(water) coordination axes (2.354(l) + 2.163(1); 2.151(1) + 2.020(1) angstrom), and the third shortest O(hydroxy)-Cu-O(hydroxy) axis (1.919(1) + 1.914(1) angstrom). This 115 K coordination sphere differs importantly to the one obtained from the 293 K data of the same compound, where two long 0(methoxy)-Cu-O(water) axes are of the same length, and only minor changes at the short 0(hydroxy)-Cu-O(hydroxy) axis are noticed. An axial symmetry of the complex with an inverse g(1.2)(g(perpendicular to)) > g(3)(g(parallel to)) pattern is observed in the temperature range from 298 to 180 K. A further decrease of temperature reveals gradual changes from axial to rhombic symmetry (g(1) > g(2) > g(3)) that is reversible. A mean-square displacement amplitude (MDSA) analysis reveals a disorder in the Cu-O(methoxy) bonds, but not in the other metal-ligand Cu-O(hydroxy) and Cu-O(water) bonds at 293 and 115 K. The disorder is significantly weaker in the 115 K structure. The MSDA analysis and the structural-EPR agreement show vibrational disorder in two coordination axes, due to the cis conformation of the complex with two 0(methoxy)-Cu-O(water) axes.}, language = {en} } @article{FudickarVomdranLinker2006, author = {Fudickar, Werner and Vomdran, Katja and Linker, Torsten}, title = {Auxiliary controlled singlet-oxygen ene reactions of cyclohexenes}, series = {Tetrahedron}, volume = {62}, journal = {Tetrahedron}, number = {46}, publisher = {Elsevier}, address = {Oxford}, issn = {0040-4020}, doi = {10.1016/j.tet.2006.07.104}, pages = {10639 -- 10646}, year = {2006}, abstract = {The photooxygenation of homochiral cyclohexene ketals, which are easily available from 2-cyclohexenone and L-tartrates, affords hydroperoxides and after reduction the corresponding allylic alcohols in good yields and high regioselectivities. This can be rationalized by electronic repulsions in a perepoxide intermediate and provides evidence for unfavorable 1,3 diaxial interactions with a dioxolane oxygen atom. Only low stereoselectivities were observed, due to the flexibility of the cyclohexene ring. However, the diastereomers could be separated and after cleavage of the auxiliary, 4-hydroxy-2-cyclohexen-1-one was isolated in enantiomerically pure form, which can serve as a building block for natural product synthesis.}, language = {en} } @article{NoteKosmellaKoetz2006, author = {Note, Carine and Kosmella, Sabine and Koetz, Joachim}, title = {Poly(ethyleneimine) as reducing and stabilizing agent for the formation of gold nanoparticles in w/o microemulsions}, series = {Colloids and surfaces : an international journal devoted to the principles and applications of colloid and interface science ; A, Physicochemical and engineering aspects}, volume = {290}, journal = {Colloids and surfaces : an international journal devoted to the principles and applications of colloid and interface science ; A, Physicochemical and engineering aspects}, number = {1-3}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0927-7757}, doi = {10.1016/j.colsurfa.2006.05.018}, pages = {150 -- 156}, year = {2006}, abstract = {This paper is focused on the use of branched poly(ethyleneimine) (PEI) as reducing as well as stabilizing agent for the formation of gold nanoparticles in different media. The process of nanoparticle formation was investigated, in the absence of any other reducing agents, in microemulsion template phase in comparison to the nucleation process in aqueous polymer solution. On the one hand, it was shown that the polyelectrolyte can be used for the controlled single-step synthesis and stabilization of gold nanoparticles via a nucleation reaction and particles with an average diameter of 7.1 nm can be produced. On the other hand, it was demonstrated that the polymer can also act as reducing and stabilizing agent in much more complex systems, i.e. in water-in-oil (w/o) microemulsion droplets. The reverse microemulsion droplets of the quaternary system sodium dodecylsulfate (SDS)/toluene-pentanol (1:1)/water were successfully used for the synthesis of gold nanoparticles. The polymer, incorporated in the droplets, exhibits reducing properties, adsorbs on the surface of the nanoparticles and prevents their aggregation. Consequently, nanoparticles of 8.6 nm can be redispersed after solvent evaporation without a change of their size. Nevertheless, the polymer acts already as a "template" during the formation of the nanoparticles in water and in microemulsion, so that an additional template effect of the microemulsion is not observed. The particle formation for both methods is checked by means of UV-vis spectroscopy and the particle size and size distribution are investigated via dynamic light scattering and transmission electron microscopy (TEM). (c) 2006 Elsevier B.V. All rights reserved.}, language = {en} } @article{MartinazzoNestSaalfranketal.2006, author = {Martinazzo, Rocco and Nest, Mathias and Saalfrank, Peter and Tantardini, Gian Franco}, title = {A local coherent-state approximation to system-bath quantum dynamics}, series = {The journal of chemical physics : bridges a gap between journals of physics and journals of chemistr}, volume = {125}, journal = {The journal of chemical physics : bridges a gap between journals of physics and journals of chemistr}, number = {19}, publisher = {American Institute of Physics}, address = {Melville}, issn = {0021-9606}, doi = {10.1063/1.2362821}, pages = {16}, year = {2006}, abstract = {A novel quantum method to deal with typical system-bath dynamical problems is introduced. Subsystem discrete variable representation and bath coherent-state sets are used to write down a multiconfigurational expansion of the wave function of the whole system. With the help of the Dirac-Frenkel variational principle, simple equations of motion-a kind of Schrodinger-Langevin equation for the subsystem coupled to (pseudo) classical equations for the bath-are derived. True dissipative dynamics at all times is obtained by coupling the bath to a secondary, classical Ohmic bath, which is modeled by adding a friction coefficient in the derived pseudoclassical bath equations. The resulting equations are then solved for a number of model problems, ranging from tunneling to vibrational relaxation dynamics. Comparison of the results with those of exact, multiconfiguration time-dependent Hartree calculations in systems with up to 80 bath oscillators shows that the proposed method can be very accurate and might be of help in studying realistic problems with very large baths. To this end, its linear scaling behavior with respect to the number of bath degrees of freedom is shown in practice with model calculations using tens of thousands of bath oscillators.}, language = {en} } @article{SchmidtStaude2006, author = {Schmidt, Bernd and Staude, Lucia}, title = {Unexpected transfer hydrogenation of C-C-double bonds during Tandem-RCM-isomerization reactions}, series = {Journal of organometallic chemistry}, volume = {691}, journal = {Journal of organometallic chemistry}, number = {24-25}, publisher = {Elsevier}, address = {Lausanne}, issn = {0022-328X}, doi = {10.1016/j.jorganchem.2006.07.011}, pages = {5218 -- 5221}, year = {2006}, abstract = {Unexpected hydrogen transfer from 2-propanol to C-C-double bonds has been observed in the course of a Tandem RCM-isomerization reaction leading to sterically congested spirocycles.}, language = {en} } @article{FudickarLinker2006, author = {Fudickar, Werner and Linker, Torsten}, title = {Imaging by sensitized oxygenations of photochromic anthracene films}, series = {Chemistry - a European journal}, volume = {12}, journal = {Chemistry - a European journal}, publisher = {WILEY-VCH}, address = {Weinheim}, issn = {0947-6539}, doi = {10.1002/chem.200600387}, pages = {9276 -- 9283}, year = {2006}, abstract = {The aliphatic anthracene compound 1 and the oligomeric anthracene 2 were synthesized. Thin films of 1 and 2 mixed with the sensitizers tetraphenylporphyrin (TPP) and methylene blue (MB) were irradiated with visible light in air. Upon formation of singlet oxygen, the anthracene units were converted quantitatively to the corresponding endoperoxides. Heating of the irradiated samples afforded the parent anthracenes with high yields. Here, we demonstrate that the kinetics and reversibility of this reaction strongly depend on the microenvironment of the anthracene groups in the two compounds. The photooxidation of thin films of I is accompanied by interesting changes in the morphology of the film and allows the first application of 1 as a nondestructive negative-tone photo-resist for lithography and as an oxidizing ink. The morphology of 2 remained unchanged after photooxidation as a result of the stabilizing oligomer backbone. This stabilizing effect significantly improves the photochromic performance of 2. The reversibility of the photooxidation is very high (> 90\%) for oligomeric films of 2 after several cycles of irradiation and beating. Decomposition of the anthracene and a loss of the activity of the sensitizer diminish slightly the performance of the monomeric species.}, language = {en} } @article{AndrianovSaalfrank2006, author = {Andrianov, Ivan and Saalfrank, Peter}, title = {Free vibrational relaxation of H adsorbed on a Si(100) surface investigated with the multi-configurational time-dependent Hartree method}, series = {Chemical physics letters}, volume = {433}, journal = {Chemical physics letters}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0009-2614}, doi = {10.1016/j.cplett.2006.11.067}, pages = {91 -- 96}, year = {2006}, abstract = {The results of a quantum-mechanical study of vibrational relaxation of hydrogen adsorbed on a Si(100) surface with the multi-configurational time-dependent Hartree (MCTDH) method are presented. A two-dimensional subsystem is coupled non-linearly to a bath of harmonic oscillators (phonons of the Si bulk), and the relaxation of subsystem vibrations proceeds primarily via a two-phonon process. Characteristic times of the system evolution agree well with our previous perturbation theory study. The vibrational population decay is non-exponential, exhibiting pronounced recurrences due to finite bath size. The dependence of the lifetimes of the vibrational levels on the bath size and on the coupling details is investigated.}, language = {en} } @article{ZenSaphiannikovaNeheretal.2006, author = {Zen, Achmad and Saphiannikova, Marina and Neher, Dieter and Grenzer, J{\"o}rg and Grigorian, Souren A. and Pietsch, Ullrich and Asawapirom, Udom and Janietz, Silvia and Scherf, Ullrich and Lieberwirth, Ingo and Wegner, Gerhard}, title = {Effect of molecular weight on the structure and crystallinity of poly(3-hexylthiophene)}, doi = {10.1021/Ma0521349}, year = {2006}, abstract = {Recently, two different groups have reported independently that the mobility of field-effect transistors made from regioregular poly(3-hexylthiophene) (P3HT) increases strongly with molecular weight. Two different models were presented: one proposing carrier trapping at grain boundaries and the second putting emphasis on the conformation and packing of the polymer chains in the thin layers for different molecular weights. Here, we present the results of detailed investigations of powders and thin films of deuterated P3HT fractions with different molecular weight. For powder samples, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and X-ray diffraction (XRD) were used to investigate the structure and crystallization behavior of the polymers. The GPC investigations show that all weight fractions possess a rather broad molecular weight distribution. DSC measurements reveal a strong decrease of the crystallization temperature and, most important, a significant decrease of the degree of crystallinity with decreasing molecular weight. To study the structure of thin layers in lateral and vertical directions, both transmission electron microscopy (TEM) and X-ray grazing incidence diffraction (GID) were utilized. These methods show that thin layers of the low molecular weight fraction consist of well-defined crystalline domains embedded in a disordered matrix. We propose that the transport properties of layers prepared from fractions of poly(3-hexylthiophene) with different molecular weight are largely determined by the crystallinity of the samples and not by the perfection of the packing of the chains in the individual crystallites}, language = {en} } @article{StrehmelLaschewskyStoesseretal.2006, author = {Strehmel, Veronika and Laschewsky, Andr{\´e} and Stoesser, Reinhard and Zehl, Andrea and Herrmann, Werner}, title = {Mobility of spin probes in ionic liquids}, doi = {10.1002/poc.1072}, year = {2006}, abstract = {The spin probes TEMPO, TEMPOL, and CAT-1 were used to investigate microviscosity and micropolarity of imidazolium based ionic liquids bearing either tetrafluoroborate or hexafluorophosphate as anions and a variation of the substitution at the imidazolium ion. The average rotational correlation times (r) obtained by complete simulation of the X-band ESR spectra of TEMPO, TEMPOL, and CAT-1 increase with increasing viscosity of the ionic liquid although no Stokes Einstein behavior is observed. This is caused by microviscosity effects of the ionic liquids shown by application of the Gierer-Wirtz theory. Interestingly, the jump of the probe molecule into the free volume of the ionic liquids is a nonactivated process. The hyperfine coupling constants (A(iso) (N-14)) of TEMPO and TEMPOL dissolved in the ionic liquids do not depend on the structure of the ionic liquids. The A(iso) (N-14) values show a micropolarity of the ionic liquids that is comparable with methylenchloride in case of TEMPO and with dimethylsulfoxide in case of TEMPOL. Micropolarity monitored by CAT-1 strongly depends on structural variation of the ionic liquid. CAT-1 dissolved in imidazolium salts substituted with shorter alkyl chains at the nitrogen atom exhibits a micropolarity comparable with dimethylsulfoxide. A significant lower micropolarity is found for imidazolium. salts bearing a longer alkyl substituent at the nitrogen atom or a methyl substituent at C-2. Copyright (c) 2006 John Wiley \& Sons, Ltd}, language = {en} } @article{SchmidtNave2006, author = {Schmidt, Bernd and Nave, Stefan}, title = {Control of ring size selectivity by substrate directable RCM}, doi = {10.1039/B604359c}, year = {2006}, abstract = {Hydroxy groups may exert strong catalyst-directing effects in olefin metathesis reactions, which are exploited for a ring size-selective RCM reaction}, language = {en} } @article{Schmidt2006, author = {Schmidt, Bernd}, title = {Olefin metathesis and isomerization : from undesired side reactions to useful synthetic methodology}, doi = {10.1016/j.molcata.2006.03.026}, year = {2006}, abstract = {Conversion of ruthenium carbene complexes to ruthenium hydride complexes by organometallic transformations in situ opens up interesting synthetic perspectives. In this account the use of Grubbs' catalyst to synthesize pent-4- enals selectively from diallyl- and allyl homoallyl ethers and scope and limitations of a Tandem RCM-isomerization sequence for the synthesis of cyclic enol ethers are discussed. (c) 2006 Elsevier B.V. All rights reserved}, language = {en} } @article{RullensVuillaumeMoussaetal.2006, author = {Rullens, F and Vuillaume, Pascal Y. and Moussa, Alain and Habib-Jiwan, Jean-Louis and Laschewsky, Andr{\´e}}, title = {Ordered polyelectrolyte "Multilayers". 7. Hybrid films self-assembled from fluorescent and smectogenic poly(diallylammonium) salts and delaminated clay}, doi = {10.1021/Cm060209x}, year = {2006}, abstract = {Homopolymers were prepared from diallylammonium monomers bearing 4-methylcoumarin and 4-cyanobiphenyl as fluorescent and mesogenic side groups, as well as their copolymers with diallyldimethylammonium chloride (DADMAC). Organic-inorganic hybrid films were electrostatically self-assembled via the layer-by-layer technique on silicon wafers and quartz plates from the chromophore-bearing polymers and an exfoliated synthetic hectorite. Photophysical studies performed in solution as well as in the self-assembled films demonstrated only a weak tendency for aggregation of the chromophores in the macromolecules. Moreover, assemblies made from the polymers carrying the cyanobiphenyl mesogen were found to exhibit a pronounced internal order}, language = {en} } @article{RullensLaschewskyDevillers2006, author = {Rullens, F and Laschewsky, Andr{\´e} and Devillers, M}, title = {Bulk and thin films of bismuth vanadates prepared from hybrid materials made from an organic polymer and inorganic salts}, doi = {10.1021/Cm051516q}, year = {2006}, abstract = {A new precursor route for the preparation of bulk oxides and thin films of bismuth vanadates is proposed. The method involves the thermal treatment under air and mild conditions of hybrid organic-inorganic precursors, made from a zwitterionic salt-free polymer matrix and selected inorganic species. Monoclinic BiVO4 was obtained in the form of bulk oxide by calcination of the powdered homogeneous hybrid materials at 600 degrees C, from precursors containing Bi and V in stoichiometric amounts. In the same way, thermodiffractometry studies performed on a hybrid material exhibiting a Bi/ V molar ratio of 2 revealed that the ionic conductor gamma-Bi4V2O11 phase can be stabilized under very soft thermal conditions (300 degrees C). Additionally, thin films of yellow monoclinic BiVO4 were for the first time fabricated, by thermal treatment of the same hybrid polymeric precursors deposited on quartz substrates by spin coating, using a layer- by-layer technique. The presence of the target phase at the surface of the plates was confirmed by X-ray diffraction as well as UV-vis measurements}, language = {en} } @article{KozlevcarOdlazekGolobicetal.2006, author = {Kozlevcar, Bojan and Odlazek, Darja and Golobic, Amalija and Pevec, Andrej and Strauch, Peter and Segedin, Primoz}, title = {Complexes with lignin model compound vanillic acid : two different carboxylate ligands in the same dinuclear tetracarboxylate complex [Cu-2(C8H7O4)(2)(O2CCH3)(2)(CH3OH)(2)]}, issn = {0277-5387}, doi = {10.1016/j.poly.2005.08.031}, year = {2006}, abstract = {Two copper(II) coordination compounds with vanillic acid C8H8O4 (1), namely [Cu- 2(C8H7O4)(2)(O2CCH3)(2)(CH3OH)(2)] (2) and [Cu-2(C8H7O4)(4)(H2O2)(2)] (3), were synthesized and characterized. Single crystals of 1-3 were obtained and their crystal structures determined. The structure of 2 shows dinuclear cage structure of copper acetate hydrate type, however with two different carboxylates, acetates and vanillic acid anions,. respectively. Both bridging anions are in pairs in trans orientation. Methanol molecules are apically coordinated (Cu-O7 2.160(2) angstrom), fulfilling square-pyramidal coordination sphere around both copper ions. The compound 2 decomposes outside mother-liquid (yielding [Cu-2(C8H7O4)(2)(O2CCH3)(2)(H2O)(2)] (2a)) with the removal of methanol, but without significant change of the dicopper tetracarboxylate cage structure, as noticed by mu(eff) 1.48 BM for 2a. Similar was found also in the X-band EPR spectra with three signals H-z1, H-perpendicular to 2 and H-z2 in the region from 0 to 600 mT. The structure of free vanillic acid 1 is composed of dimeric units of two molecules, connected by two parallel hydrogen bonds between carboxylate group of each other (O1-H(...)O2 2.642(3) angstrom), while the structure of 3 is of [Cu-2(O2CCH3)(4)(H2O)(2)] type. Interestingly, an additional signal in the EPR spectra of 3 is found at 80 mT (H- perpendicular to 1) at 298 and at 116 K, next to three signals H-z1, H-perpendicular to 2 and H-z2.}, language = {en} } @article{KoetzJagielskiKosmellaetal.2006, author = {Koetz, Joachim and Jagielski, Nicole and Kosmella, Sabine and Friedrich, Alwin and Kleinpeter, Erich}, title = {CdS nanocubes formed in phosphatidylcholin-based template phases}, volume = {288}, issn = {0927-7757}, doi = {10.1016/j.colsurfa.2006.01.013}, pages = {43 -- 1-3}, year = {2006}, abstract = {The paper is focused on the characterization and use of phosphatidylcholine (PC)-based inverse microemulsions as a template phase for the CdS nanoparticle formation. The optically clear, isotropic phase in the oil corner was identified as a "classical{\"o} water-in-oil microemulsion by means of NMR-diffusion measurements. Because of the very small dimensions of the water droplets, the isotropic phase shows a Newtonian-like flow behavior, and adequate amounts of bulk water cannot be detected by DSC. It is demonstrated that this w/o microemulsion can be used successfully as a nanoreactor for the formation of CdS nanoparticles with diameters of 4-5 nm. During the following process of solvent evaporation the individual small CdS nanoparticles aggregate to significant larger cubic nanoparticles, with an edge length of 2-40 nm, arranged in well-defined mosaic-like superstructures. In presence of SDS the nanocubes were stable up to 800 °C. It has to be stated here that polyelectrolytes prevent the formation of such well-ordered superstructures.}, language = {en} } @article{KleinpeterHolzberger2006, author = {Kleinpeter, Erich and Holzberger, Anja}, title = {Structure, intramolecular flexibility, and complexation of aza crown ethers to anions H2PO4- and HSO4- in nonprotic solvents}, series = {Tetrahedron}, volume = {62}, journal = {Tetrahedron}, number = {43}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0040-4020}, doi = {10.1016/j.tet.2006.07.074}, pages = {10237 -- 10247}, year = {2006}, abstract = {Both the structure and intramolecular flexibility of a series of aza crown ethers were studied by experimental NMR and theoretical molecular modeling. The stoichiometries of complexation to the anions H2PO4- and resulting complex stabilities were determined by experimental NMR (1H, 31P) titration and, in addition, the structure and mobility changes of the aza crown ethers upon complexation were also examined.}, language = {en} } @article{EngelhardKumkeLoehmannsroeben2006, author = {Engelhard, Sonja and Kumke, Michael Uwe and L{\"o}hmannsr{\"o}ben, Hans-Gerd}, title = {Examples of the application of optical process and quality sensing (OPQS) to beer brewing and polyurethane foaming processes}, issn = {1618-2642}, doi = {10.1007/s00216-005-3364-4}, year = {2006}, abstract = {Optical methods play an important role in process analytical technologies (PAT). Four examples of optical process and quality sensing (OPQS) are presented, which are based on three important experimental techniques: near- infrared absorption, luminescence quenching, and a novel method, photon density wave (PDW) spectroscopy. These are used to evaluate four process and quality parameters related to beer brewing and polyurethane (PU) foaming processes: the ethanol content and the oxygen (O-2) content in beer, the biomass in a bioreactor, and the cellular structures of PU foam produced in a pilot production plant}, language = {en} } @article{DambacherKlieglHofmannetal.2006, author = {Dambacher, Michael and Kliegl, Reinhold and Hofmann, Markus and Jacobs, Arthur M.}, title = {Frequency and predictability effects on event-related potentials during reading}, issn = {0006-8993}, doi = {10.1016/j.brainres.2006.02.010}, year = {2006}, abstract = {Effects of frequency, predictability, and position of words on event-related potentials were assessed during word-by-word sentence reading in 48 subjects in an early and in a late time window corresponding to P200 and N400. Repeated measures multiple regression analyses revealed a P200 effect in the high-frequency range also the P200 was larger on words at the beginning and end of sentences than on words in the middle of sentences (i.e., a quadratic effect of word position). Predictability strongly affected the N400 component; the effect was stronger for low than for high- frequency words. The P200 frequency effect indicates that high-frequency words are lexically accessed very fast, independent of context information. Effects on the N400 suggest that predictability strongly moderates the late access especially of low-frequency words. Thus, contextual facilitation on the N400 appears to reflect both lexical and post- lexical stages of word recognition, questioning a strict classification into lexical and post-lexical processes.}, language = {en} } @article{BalciKochKleinpeter2006, author = {Balci, Kubilay and Koch, Andreas and Kleinpeter, Erich}, title = {A comparative vibrational spectroscopic investigation of free mn-12S(2)O(2) and fn-12S(2)O(2) dithiacrown ethers based on DFT calculations}, issn = {0022-2860}, doi = {10.1016/j.molstruc.2005.10.048}, year = {2006}, abstract = {A successful assignment for the fundamental bands observed in the experimental IR spectra of mn-12S(2)O(2) and fn-12S(2)O(2) dithiacrown ethers was achieved by the aid of the density functional theory (DFT) based quantum mechanical calculations carried out at the 133LYP/6-31G(d) and B3LYP/6-31 + G(d) level of theory. Two different scaling approaches, '(i) scaled quantum mechanics force field (SQM FF) methodology', and (ii) the 'scaling frequencies with dual empirical scale factors', were used in order to fit the calculated harmonic frequencies to the experimental ones. Potential energy distribution (PED) calculations were carried out to define the internal coordinate contributions to each normal mode and to define the corresponding normal modes of the molecules. The effects of the conformational differences onto the IR active normal modes of the two isomeric molecules and their corresponding experimental frequencies were discussed in the light of the calculated spectral data.}, language = {en} } @article{AndayiYenesewDereseetal.2006, author = {Andayi, Andrew W. and Yenesew, Abiy and Derese, Solomon and Midiwo, Jacob O. and Gitu, Peter M. and Jondiko, Ogoche J. I. and Akala, Hoseah M. and Liyala, Pamela and Wangui, Julia and Waters, Norman C. and Heydenreich, Matthias and Peter, Martin G.}, title = {Antiplasmodial flavonoids from Erythrina sacleuxii}, issn = {0032-0943}, doi = {10.1055/s-2005-873200}, year = {2006}, abstract = {The acetone extracts of the root bark and stem bark of Erythrina sacleuxii showed antiplasmodial activities against the chloroquine-sensitive (D6) and chloroquine-resistant (W2) strains of Plasmodium falciparum. Chromatographic separation of the acetone extract of the root bark afforded a new isoflavone, 7-hydroxy-4 -methoxy-3'- prenylisoflavone (trivial name 5-deoxy-3' - prenylbiochanin A) along with known isoflavonoids as the antiplasmodial principles. Flavonoids and isoflavonoids isolated from the stem bark of E. sucleuxii were also tested and showed antiplasmodial activities. The structures were determined on the basis of spectroscopic evidence}, language = {en} } @article{WattebledLaschewskyMoussaetal.2006, author = {Wattebled, Laurent and Laschewsky, Andr{\´e} and Moussa, Alain and Habib-Jiwan, Jean-Louis}, title = {Aggregation numbers of cationic oligomeric surfactants : A time-resolved fluorescence quenching study}, doi = {10.1021/La052414h}, year = {2006}, abstract = {The micelle aggregation numbers (N-agg) of several series of cationic oligomeric surfactants were determined by time-resolved fluorescence quenching (TRFQ) experiments, using advantageously 9,10-dimethylanthracene as fluorophore. The study comprises six dimeric ("gemini"), three trimeric, and two tetrameric surfactants, which are quaternary ammonium chlorides, with medium length spacer groups (C-3-C-6) separating the individual surfactant fragments. Two standard cationic surfactants served as references. The number of hydrophobic chains making up a micellar core is relatively low for the oligomeric surfactants, the spacer length playing an important role. For the dimers, the number decreases from 32 to 21 with increasing spacer length. These numbers decrease further with increasing degree of oligomerization down to values of about 15. As for many conventional ionic surfactants, the micelles of all oligomers studied grow only slightly with the concentration, and they remain in the regime of small micelles up to concentrations of at least 3 wt \%.}, language = {en} } @article{ShainyanUshakovKochetal.2006, author = {Shainyan, Bagrat A. and Ushakov, Igor A. and Koch, Andreas and Kleinpeter, Erich}, title = {Stereodynamics of 1-(methylsulfonyl)-3,5-bis(trifluoromethylsulfonyl)-1,3,5-triazinane: Experimental and theoretical analysis}, doi = {10.1021/Jo061112x}, year = {2006}, abstract = {Dynamic NMR of 1-(methylsulfonyl)-3,5-bis(trifluoromethylsulfonyl)-1,3,5-triazinane reveals the existence of three conformers and two dynamic processes: ring inversion and rotation about the N-S bond, both processes having Delta G(double dagger) = 13.5 kcal/mol. An unprecedented large reverse Perlin effect (J(CHax) > J(CHeq)) was found experimentally and calculated theoretically.}, language = {en} } @article{LaschewskyKirstenSkrabaniaetal.2006, author = {Laschewsky, Andr{\´e} and Kirsten, Juliane and Skrabania, Katja and Storsberg, Joachim}, title = {Designing functional macrosurfactants via triblock tercopolymers}, issn = {0065-7727}, year = {2006}, language = {en} } @article{SonnenburgAdelhelmAntoniettietal.2006, author = {Sonnenburg, Kirstin and Adelhelm, Philipp and Antonietti, Markus and Smarsly, Bernd and N{\"o}ske, Robert and Strauch, Peter}, title = {Synthesis and characterization of SiC materials with hierarchical porosity obtained by replication techniques}, doi = {10.1039/B604819F}, year = {2006}, abstract = {Porous silicon carbide monoliths were obtained using the infiltration of preformed SiO2 frameworks with appropriate carbon precursors such as mesophase pitch. The initial SiO2 monoliths possessed a hierarchical pore system, composed of an interpenetrating bicontinuous macropore structure and 13 nm mesopores confined in the macropore walls. After carbonization, further heat treatment at ca. 1400 degrees C resulted in the formation of a SiC-SiO2 composite, which was converted into a porous SiC monolith by post-treatment with ammonium fluoride solution. The resulting porous SiC featured high crystallinity, high chemical purity and showed a surface area of 280 m(2) g(-1) and a pore volume of 0.8 ml g(-1)}, language = {en} } @article{KumkeDoscheFlehretal.2006, author = {Kumke, Michael Uwe and Dosche, Carsten and Flehr, Roman and Trowitzsch-Kienast, Wolfram and L{\"o}hmannsr{\"o}ben, Hans-Gerd}, title = {Spectroscopic characterization of the artificial siderophore pyridinochelin}, issn = {0939-5075}, year = {2006}, language = {en} } @article{GroboschSchildeTiersch2006, author = {Grobosch, Thomas and Schilde, Uwe and Tiersch, Brigitte}, title = {Abtrennung von Arsen und anderer Schwermetalle mit impr{\"a}gnierten Adsorberpolymeren - teil 2: Abtrennung von Blei, Kupfer, Nickel und Zink}, issn = {0009-286X}, doi = {10.1002/cite.200500171}, year = {2006}, language = {de} } @article{SchmidtNave2006, author = {Schmidt, Bernd and Nave, Stefan}, title = {Palladium-catalyzed O-allylation of alpha-hydroxy carbonyl compounds}, doi = {10.1002/adsc.200505361}, year = {2006}, abstract = {alpha-Hydroxy carbonyl compounds undergo smooth O-allylation using allylic carbonates and Pd(0) catalysts. This method has significant advantages over other O-allylation methods as it provides a solution to several problems previously observed for this synthetic transformation}, language = {en} } @article{SzatmariTothKochetal.2006, author = {Szatmari, Istvan and Toth, Diana and Koch, Andreas and Heydenreich, Matthias and Kleinpeter, Erich and Fulop, Ferenc}, title = {Study of the substituent-influenced anomeric effect in the ring-chain tautomerism of 1-alkyl-3-aryl-naphth[1,2- e][1,3]oxazines}, doi = {10.1002/ejoc.200600563}, year = {2006}, abstract = {The stabilities of the trans (B) and cis (C) tautomeric ring forms that are experimentally observed in the ring- chain tautomeric interconversion of 1-alkyl-3-aryl-2,3-dihydro-1H-naphth[1,2-e][1,3]oxazines has been investigated. Stability differences are explained by the analysis of the natural bond orbital results for the lone pairs of electrons that are on the heteroatoms in the oxazine ring system and by regression analysis of the calculated 13C NMR chemical shift values.}, language = {en} } @article{StrehmelLaschewskyWetzeletal.2006, author = {Strehmel, Veronika and Laschewsky, Andr{\´e} and Wetzel, Hendrik and Gornitz, Eckhard}, title = {Free radical polymerization of n-butyl methacrylate in ionic liquids}, doi = {10.1021/Ma0516945}, year = {2006}, abstract = {Ionic liquids based on imidazolium, pyridinium, and alkylammonium salts were investigated as solvents in free radical polymerization of the model monomer n-butyl methacrylate. The properties of the ionic liquids were systematically varied by changing the length of the alkyl substituents on the cations, and by employing different anions such as tetrafluoroborate, hexafluorophosphate, tosylate, triflate, alkyl sulfates and dimethyl phosphate. Results were compared to analogous polymerizations in toluene and in bulk. The solvents have no detectable influence on polymer tacticity. However, the molar masses obtained and the degree of polymerization, respectively, are very sensitive to the choice of the solvent. The degrees of polymerization are significantly higher when polymerizations were carried out in ionic liquids compared to polymerization in toluene, and can even exceed the values obtained by bulk polymerization. Imidazolium salts unsubstituted at C-2 result in an increase in the degree of polymerization of the poly(butyl methacrylate) with increasing viscosity of these ionic liquids. Methyl substitution at C-2 of the imidazolium ion results in an increase in the viscosity of the ionic liquid and in a viscosity independent degree of polymerization of the poly(butyl methacrylate). Ionic liquids based on imidazolium salts seem preferable over pyridinium and alkylammonium salts because of the higher degree of polymerization of the poly(butyl methacrylate)s obtained in the imidazolium salts. The glass transition temperatures and thermal stabilities are higher for poly(butyl methacrylate)s synthesized in the ionic liquids compared to the polymer made in toluene}, language = {en} } @article{KlinkaBalentovaBernatetal.2006, author = {Klinka, Karel D. and Balentova, Eva and Bern{\´a}t, Juraj and Imrich, J{\´a}n and Vavrusov{\´a}, Martina and Pihlaja, Kalevi and Koch, Andreas and Kleinpeter, Erich and Kelling, Alexandra and Schilde, Uwe}, title = {Structural revision of products resulting from the reaction of methylhydrazine with acridin-9-yl isothiocyanate due to unexpected acridinyl migration And further reactions}, issn = {1551-7004}, year = {2006}, abstract = {The reaction of methyl acridin-9-ylthiosemicarbazide under basic conditions with methyl bromoacetate resulted in a 1,3-thiazolin-4-one structure as provided by X-ray crystallography. The structure forced a re-evaluation of the reactant methyl acridin-9-ylthiosemicarbazide, originally thought to be 2-methyl 4-acridin-9-ylthiosemicarbazide based on synthetic expectations, but which when examined by X-ray crystallography was found to be in fact the isomeric 2- methyl 1-acridin-9-ylthiosemicarbazide resulting from rearrangement via a spiro form which it is in equilibrium with in solution. The product resulting from reaction with methyl iodide was also studied and the previously reported semicarbazide produced by reaction with MNO was re-examined. In both cases, the 1,2 isomer rather than the 2,4 isomer was found to be present based on the sign of the 3JCH3,N11 coupling. Full characterization of the compounds was rendered by 1H, 13C, and 15N solution-state NMR, and in the solid state, by both 13C and 15N NMR.}, language = {en} } @article{GroboschMicklerFeisteletal.2006, author = {Grobosch, Thomas and Mickler, Wulfhard and Feistel, Lothar and Schilde, Uwe}, title = {Separation of arsenic and other heavy metals with impregnated adsorber polymers : chapter 1: synthesis of the impregnation medium and separation of arsenic}, issn = {0009-286X}, doi = {10.1002/cite.200500170}, year = {2006}, language = {en} } @article{Kleinpeter2006, author = {Kleinpeter, Erich}, title = {Push-pull alkenes : structure and pi-electron distribution}, doi = {10.2298/Jsc0601001k}, year = {2006}, abstract = {Push-pull alkenes are substituted alkenes with one or two electron-donating substituents on one end of C=C double bond and with one or two electron-accepting substituents at the other end. Allowance for pi-electron delocalization leads to the central C=C double bond becoming ever more polarized and with rising push-pull character, the pi-bond order of this double bond is reduced and, conversely, the corresponding pi-bond orders of the C-Don and C- Ace bonds are accordingly increased. This push-pull effect is of decisive influence on both the dynamic behavior and the chemical reactivity of this class of compounds and thus it is Of Considerable interest to both determine and to quantify the inherent push-pull effect. previously, the barriers to rotation about the C=C, C-Don and/or C-Acc partial double bonds (Delta G(not equal), as determined by dynamic NMR spectroscopy) or the C-13 chemical shift difference of the polarized C=C partial double bond (Delta delta(C=C)) were employed for this purpose, However, these parameters can have serious limitations, viz. the barriers can be immeasurable on the NMR timescale (either by being too high or too low-, heavily-biased conformers are present, etc.) or Delta delta(C=C) behaves in a non-additive manner with respect to the combination of the four substituents. Hence, a general parameter to quantify the push-pull effect is not yet available. Ab initio MO calculations on a collection of compounds, together with NBO analysis, provided valuable information on the structure, bond energies, electron occupancies and bonding/antibonding interactions. In addition to Delta G(C=C)(not equal) (either experimentally determined or theoretically calculated) and Delta delta(C=C), the bond length of the C=C partial double bond was also examined and it proved to be a reliable parameter to quantify the push-pull effect. Equally so, the quotient of the occupation numbers of the antibonding and bonding pi orbitals of the central C=C partial double bond ( pi*(C=C)/pi(C=C) ) could also be employed for this purpose}, language = {en} } @phdthesis{Koehler2006, author = {K{\"o}hler, Karen}, title = {Temperature-induced rearrangements of polyelectrolyte multilayer capsules : mechanisms and applications}, address = {Potsdam}, pages = {XV, 118, B S. : Ill., graph. Darst.}, year = {2006}, language = {en} } @article{GorfmanTsirelsonPucheretal.2006, author = {Gorfman, Semen and Tsirelson, Vladimir and Pucher, Andreas and Morgenroth, Wolfgang and Pietsch, Ullrich}, title = {X-ray diffraction by a crystal in a permanent external electric field : electric-field-induced structural response in alpha-GaPO4}, issn = {0108-7673}, doi = {10.1107/S0108767305036111}, year = {2006}, abstract = {For the first time, site-selective distortion has been investigated for two different structural units in the ternary compound alpha-GaPO4 under the influence of a permanent external electric field. Based on 54 measured reflection intensities, the electric-field-induced distortion of PO4 and GaO4 tetrahedra in alpha-GaPO4 crystals is evaluated using a model of pseudoatomic displacements introduced recently [Gorfman, Tsirelson \& Pietsch (2005). Acta Cryst. A61, 387- 396]. A stronger variation of the P-O bond lengths in the PO4 tetrahedron was found compared to the bonds in the GaO4 tetrahedron. The different distortions of the tetrahedra owing to the electric field were analysed in terms of the valence charge density of alpha-GaPO4 and its topological characteristics. The larger charge of the P pseudoatom compared to the Ga atom was recognized as the main reason for the higher sensitivity of the PO4 tetrahedron to a permanent external electric field}, language = {en} } @article{KietzkeEgbeHoerholdetal.2006, author = {Kietzke, Thomas and Egbe, Daniel A. M. and H{\"o}rhold, Hans-Heinrich and Neher, Dieter}, title = {Comparative study of M3EH-PPV-based bilayer photovoltaic devices}, issn = {4018-4022}, doi = {10.1021/Ma0601991}, year = {2006}, abstract = {We have recently shown that efficient polymer solar cells can be fabricated by using a weakly soluble derivative of poly-p-vinylene (M3EH-PPV) as the electron donor. Here we present studies on bilayer devices using organic electron acceptors with varying LUMO levels and M3EH-PPV. It is found that the open-circuit voltage scales linearly with the LUMO level of the acceptor, reaching values as high as 1.5 V when cyano-substituted poly(p-phenyleneethynylene)-alt- poly(p-phenylenevinylene) copolymers are used. Further, we discovered that for an increasing number of triple bonds in the repeat unit of the acceptor polymer the device performance decreases with increasing thickness of the acceptor layer. Also, the quantum efficiency was smaller when using polymers with higher LUMO levels. Thus, further effort is needed to design optimum acceptor polymers for devices exhibiting large open-circuit voltage and high quantum efficiency}, language = {en} } @article{SchmidtHermanns2006, author = {Schmidt, Bernd and Hermanns, Jolanda}, title = {Ring closing metathesis of substrates containing more than two C-C-double bonds : rapid access to functionalized heterocycles}, year = {2006}, abstract = {In most cases where ring closing metathesis is applied to the synthesis of heterocycles, alpha,omega-dienes are used as precursors. If substrates containing more than two double bonds are subjected to a metathesis reaction, carba- or heterocycles bearing additional exocyclic alkene functionality result, or multiple ring closing processes occur. This offers interesting and potentially very useful synthetic perspectives. On the other hand, selectivity problems need to be addressed as the cyclization of substrates with more than two double bonds available for olefin metathesis may result in constitutional isomers or stereoisomers. This review highlights problems and opportunities evolving from ring closing metathesis of tri-, tetra-, and polyenes as a strategy for the selective synthesis of functionalized heterocycles. The chapter on RCM of trienes is subdivided according to the symmetry of the metathesis precursor. The following two chapters deal with the double or multiple RCM of tetra- or polyenes. These processes are further classified according to the preferred cyclization mode. Finally, the application of cascade or domino metathesis reactions to the synthesis of heterocycles will be discussed. These processes can be classified into those where exclusively C-C-double bonds take part in the metathesis reaction, and those where one or more C-C-triple bonds are involved}, language = {en} } @phdthesis{Kim2006, author = {Kim, Boo Geun}, title = {Radikalische Additionen an unges{\"a}ttigte Kohlenhydrate als Schl{\"u}sselschritt in der Synthese von Kohlenhydrat-C-Analoga}, address = {Potsdam}, pages = {113 Bl. : graph. Darst.}, year = {2006}, language = {de} } @article{Stoecklein2006, author = {St{\"o}cklein, Walter F. M.}, title = {Molecule-detective}, year = {2006}, abstract = {Biosensors are analytical devices incorporating biological material (receptor) intimately associated with or integrated within a physicochernical transducer. Advantages are the high selectivity for analyte detection. Examples given comprise the very successful commercial blood glucose biosensors made for the self-control by the diabetic patients. Other biosensors are part of an analytic system, including the sensor chips Of surface plasmon resonance or interferometry based devices, piezoelectric or reflectometric sensors capable of direct measurement of mass changes, and thermometric and other reagentless sensors. The development of nanotubes-based devices allows for significant enhancment of the signal-to-noise ratio of the biosensors. A milestone on the way towards miniaturization and parallelization of biosensors is the recently developed and prize-winning electronic DNA chip}, language = {en} } @article{YenesewKiplagatDereseetal.2006, author = {Yenesew, Abiy and Kiplagat, John T. and Derese, Solomon and Midiwo, Jacob O. and Kabaru, Jacques M. and Heydenreich, Matthias and Peter, Martin G.}, title = {Two unusual rotenoid derivatives, 7a-O-methyl-12a-hydroxydeguelol and spiro-13-homo-13-oxaelliptone, from the seeds of Derris trifoliata}, doi = {10.1016/j.phytochem.2006.01.002}, year = {2006}, abstract = {The crude methanol extract of the seeds of Derris trifoliata showed potent and dose dependent larvicidal activity against the 2nd instar larvae of Aedes aegypti. From this extract two unusual rotenoid derivatives, a rotenoloid (named 7a-O-methyl-12a-hydroxydeguelol) and a spirohomooxarotenoid (named spiro-13-homo-13-oxaelliptone), were isolated and characterised. In addition a rare natural chromanone (6,7-dimethoxy-4-chromanone) and the known rotenoids rotenone, tephrosin and dehydrodeguelin were identified. The structures were assigned on the basis of spectroscopic evidence. The larvicidal activity of the crude extract is mainly due to rotenone. (c) 2006 Elsevier Ltd. All rights reserved}, language = {en} } @article{HoldtMuellerKellingetal.2006, author = {Holdt, Hans-J{\"u}rgen and M{\"u}ller, Holger and Kelling, Alexandra and Drexler, Hans-Joachim and M{\"u}ller, Thomas and Schwarze, Thomas and Schilde, Uwe and Starke, Ines}, title = {Mercury(II) chloride and iodide complexes of dithia- and tetrathiacrown ethers}, issn = {0044-2313}, doi = {10.1002/zaac.200500281}, year = {2006}, abstract = {The complexes [(HgCl2)(2)((ch)(2)30S(4)O(6))] (1), [HgCl,(mn21S(2)O(5))] (2), [HgCl2(ch18S(2)O(4))] (3) and [HgI(meb12S(2)O(2))](2)[Hg2I6] (4) have been synthesized, characterized and their crystal structures were determined. In [(HgCl2)(2)((ch)(2)3OS(4)O(6))] two HgCl2 units are discretely bonded within the ligand cavity of the 30-membered dichinoxaline-tetrathia-30-crown-10 ((ch)(2)30S(4)O(6)) forming a binuclear complex. HgCl2 forms I : I "in-cavity" complexes with the 21-membered maleonitrile-dithia-21-crown-7(mn21S(2)O(5)) ligand and the 18-membered chinoxaline- dithia-18-crown-6 (ch18S(2)O(4)) ligand, respectively. The 12-membered 4-methyl-benzo-dithia-12-crown-4 (meb12S(2)O(2)) ligand gave with two equivalents HgI2 the compound [HgI(meb12S(2)O(2))](2)[Hg2I6]. In the cation [HgI(meb12S(2)O(2))](+) meb12S(2)O(2) forms with the cation HgI+ a half-sandwich complex}, language = {en} } @phdthesis{Klamroth2006, author = {Klamroth, Tillmann}, title = {Quantum mechanical simulations for correlated many-electron dynamics and electron induced processes at surfaces}, address = {Potsdam}, pages = {206 S. : graph. Darst.}, year = {2006}, language = {en} }