@article{ZhuPilzCotton2019, author = {Zhu, Chuanbin and Pilz, Marco and Cotton, Fabrice Pierre}, title = {Which is a better proxy, site period or depth to bedrock, in modelling linear site response in addition to the average shear-wave velocity?}, series = {Bulletin of earthquake engineering : official publication of the European Association for Earthquake Engineering}, volume = {18}, journal = {Bulletin of earthquake engineering : official publication of the European Association for Earthquake Engineering}, number = {3}, publisher = {Springer}, address = {Dordrecht}, issn = {1570-761X}, doi = {10.1007/s10518-019-00738-6}, pages = {797 -- 820}, year = {2019}, abstract = {This study aims to identify the best-performing site characterization proxy alternative and complementary to the conventional 30 m average shear-wave velocity V-S30, as well as the optimal combination of proxies in characterizing linear site response. Investigated proxies include T-0 (site fundamental period obtained from earthquake horizontal-to-vertical spectral ratios), V-Sz (measured average shear-wave velocities to depth z, z = 5, 10, 20 and 30 m), Z(0.8) and Z(1.0) (measured site depths to layers having shear-wave velocity 0.8 and 1.0 km/s, respectively), as well as Z(x-infer) (inferred site depths from a regional velocity model, x = 0.8 and 1.0, 1.5 and 2.5 km/s). To evaluate the performance of a site proxy or a combination, a total of 1840 surface-borehole recordings is selected from KiK-net database. Site amplifications are derived using surface-to-borehole response-, Fourier- and cross-spectral ratio techniques and then are compared across approaches. Next, the efficacies of 7 single-proxies and 11 proxy-pairs are quantified based on the site-to-site standard deviation of amplification residuals of observation about prediction using the proxy or the pair. Our results show that T-0 is the best-performing single-proxy among T-0, Z(0.8), Z(1.0) and V-Sz. Meanwhile, T-0 is also the best-performing proxy among T-0, Z(0.8), Z(1.0) and Z(x-infer) complementary to V-S30 in accounting for the residual amplification after V-S30-correction. Besides, T-0 alone can capture most of the site effects and should be utilized as the primary site indicator. Though (T-0, V-S30) is the best-performing proxy pair among (V-S30, T-0), (V-S30, Z(0.8)), (V-S30, Z(1.0)), (V-S30, Z(x-infer)) and (T-0, V-Sz), it is only slightly better than (T-0, V-S20). Considering both efficacy and engineering utility, the combination of T-0 (primary) and V-S20 (secondary) is recommended. Further study is needed to test the performances of various proxies on sites in deep sedimentary basins.}, language = {en} } @article{BarthGeertsemaBevingtonetal.2019, author = {Barth, Sophia and Geertsema, Marten and Bevington, Alexandre R. and Bird, Alison L. and Clague, John J. and Millard, Tom and Bobrowsky, Peter T. and Hasler, Andreas and Liu, Hongjiang}, title = {Landslide response to the 27 October 2012 earthquake (M-W 7.8), southern Haida Gwaii, British Columbia, Canada}, series = {Landslides : journal of the International Consortium on Landslides, ICL}, volume = {17}, journal = {Landslides : journal of the International Consortium on Landslides, ICL}, number = {3}, publisher = {Springer}, address = {Heidelberg}, issn = {1612-510X}, doi = {10.1007/s10346-019-01292-7}, pages = {517 -- 526}, year = {2019}, abstract = {In this paper, we examine the influence of the 27 October 2012, M-w 7.8 earthquake on landslide occurrence in the southern half of Haida Gwaii (formerly Queen Charlotte Islands), British Columbia, Canada. Our 1350 km(2) study area is undisturbed, primarily forested terrain that has not experienced road building or timber harvesting. Our inventory of landslide polygons is based on optical airborne and spaceborne images acquired between 2007 and 2018, from which we extracted and mapped 446 individual landslides (an average of 33 landslides per 100 km(2)). The landslide rate in years without major earthquakes averages 19.4 per year, or 1.4/100 km(2)/year, and the annual average area covered by non-seismically triggered landslides is 35 ha/year. The number of landslides identified in imagery closely following the 2012 earthquake, and probably triggered by it, is 244 or an average of about 18 landslides per 100 km(2). These landslides cover a total area of 461 ha. In the following years-2013-2016 and 2016-2018-the number of landslides fell, respectively, to 26 and 13.5 landslides per year. In non-earthquake years, most landslides happen on south-facing slopes, facing the prevailing winds. In contrast, during or immediately after the earthquake, up to 32\% of the landslides occurred on north and northwest-facing slopes. Although we could not find imagery from the day after the earthquake, overview reconnaissance flights 10 and 16 days later showed that most of the landslides were recent, suggesting they were co-seismic.}, language = {en} } @article{WangHerzschuhLiuetal.2014, author = {Wang, Yongbo and Herzschuh, Ulrike and Liu, Xingqi and Korup, Oliver and Diekmann, Bernhard}, title = {A high-resolution sedimentary archive from landslide-dammed Lake Mengda, north-eastern Tibetan Plateau}, series = {Journal of paleolimnolog}, volume = {51}, journal = {Journal of paleolimnolog}, number = {2}, publisher = {Springer}, address = {Dordrecht}, issn = {0921-2728}, doi = {10.1007/s10933-012-9666-6}, pages = {303 -- 312}, year = {2014}, abstract = {Lacustrine sediments have been widely used to investigate past climatic and environmental changes on millennial to seasonal time scales. Sedimentary archives of lakes in mountainous regions may also record non-climatic events such as earthquakes. We argue herein that a set of 64 annual laminae couplets reconciles a stratigraphically inconsistent accelerator mass spectrometry (AMS) C-14 chronology in a similar to 4-m-long sediment core from Lake Mengda, in the north-eastern Tibetan Plateau. The laminations suggest the lake was formed by a large landslide, triggered by the 1927 Gulang earthquake (M = 8.0). The lake sediment sequence can be separated into three units based on lithologic, sedimentary, and isotopic characteristics. Starting from the bottom of the sequence, these are: (1) unweathered, coarse, sandy valley-floor deposits or landslide debris that pre-date the lake, (2) landslide-induced, fine-grained soil or reworked landslide debris with a high organic content, and (3) lacustrine sediments with low organic content and laminations. These annual laminations provide a high-resolution record of anthropogenic and environmental changes during the twentieth century, recording enhanced sediment input associated with two phases of construction activities. The high mean sedimentation rates of up to 4.8 mm year(-1) underscore the potential for reconstructing such distinct sediment pulses in remote, forested, and seemingly undisturbed mountain catchments.}, language = {en} } @article{GorumKorupvanWestenetal.2014, author = {Gorum, Tolga and Korup, Oliver and van Westen, Cees J. and van der Meijde, Mark and Xu, Chong and van der Meer, Freek D.}, title = {Why so few? Landslides triggered by the 2002 Denali earthquake, Alaska}, series = {Quaternary science reviews : the international multidisciplinary research and review journal}, volume = {95}, journal = {Quaternary science reviews : the international multidisciplinary research and review journal}, publisher = {Elsevier}, address = {Oxford}, issn = {0277-3791}, doi = {10.1016/j.quascirev.2014.04.032}, pages = {80 -- 94}, year = {2014}, abstract = {The 2002 M-w 7.9 Denali Fault earthquake, Alaska, provides an unparalleled opportunity to investigate in quantitative detail the regional hillslope mass-wasting response to strong seismic shaking in glacierized terrain. We present the first detailed inventory of similar to 1580 coseismic slope failures, out of which some 20\% occurred above large valley glaciers, based on mapping from multi-temporal remote sensing data. We find that the Denali earthquake produced at least one order of magnitude fewer landslides in a much narrower corridor along the fault ruptures than empirical predictions for an M 8 earthquake would suggest, despite the availability of sufficiently steep and dissected mountainous topography prone to frequent slope failure. In order to explore potential controls on the reduced extent of regional coseismic landsliding we compare our data with inventories that we compiled for two recent earthquakes in periglacial and formerly glaciated terrain, i.e. at Yushu, Tibet (M-w 6.9, 2010), and Aysen Fjord, Chile (2007 M-w 6.2). Fault movement during these events was, similarly to that of the Denali earthquake, dominated by strike-slip offsets along near-vertical faults. Our comparison returns very similar coseismic landslide patterns that are consistent with the idea that fault type, geometry, and dynamic rupture process rather than widespread glacier cover were among the first-order controls on regional hillslope erosional response in these earthquakes. We conclude that estimating the amount of coseismic hillslope sediment input to the sediment cascade from earthquake magnitude alone remains highly problematic, particularly if glacierized terrain is involved. (C) 2014 Elsevier Ltd. All rights reserved.}, language = {en} } @article{FanvanWestenKorupetal.2012, author = {Fan, Xuanmei and van Westen, Cees J. and Korup, Oliver and Gorum, Tolga and Xu, Qiang and Dai, Fuchu and Huang, Runqiu and Wang, Gonghui}, title = {Transient water and sediment storage of the decaying landslide dams induced by the 2008 Wenchuan earthquake, China}, series = {Geomorphology : an international journal on pure and applied geomorphology}, volume = {171}, journal = {Geomorphology : an international journal on pure and applied geomorphology}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0169-555X}, doi = {10.1016/j.geomorph.2012.05.003}, pages = {58 -- 68}, year = {2012}, abstract = {Earthquake-triggered landslide dams are potentially dangerous disrupters of water and sediment flux in mountain rivers, and capable of releasing catastrophic outburst flows to downstream areas. We analyze an inventory of 828 landslide dams in the Longmen Shan mountains, China, triggered by the M-w 7.9 2008 Wenchuan earthquake. This database is unique in that it is the largest of its kind attributable to a single regional-scale triggering event: 501 of the spatially clustered landslides fully blocked rivers, while the remainder only partially obstructed or diverted channels in steep watersheds of the hanging wall of the Yingxiu-Beichuan Fault Zone. The size distributions of the earthquake-triggered landslides, landslide dams, and associated lakes (a) can be modeled by an inverse gamma distribution; (b) show that moderate-size slope failures caused the majority of blockages; and (c) allow a detailed assessment of seismically induced river-blockage effects on regional water and sediment storage. Monte Carlo simulations based on volumetric scaling relationships for soil and bedrock failures respectively indicate that 14\% (18\%) of the estimated total coseismic landslide volume of 6.4 (14.6) x 10(9) m(3) was contained in landslide dams, representing only 1.4\% of the >60,000 slope failures attributed to the earthquake. These dams have created storage capacity of similar to 0.6x 10(9) m(3) for incoming water and sediment. About 25\% of the dams containing 2\% of the total river-blocking debris volume failed one week after the earthquake; these figures had risen to 60\% (similar to 20\%), and >90\% (>90\%) within one month, and one:year, respectively, thus also emptying similar to 92\% of the total potential water and sediment storage behind these, dams within one year following the earthquake. Currently only similar to 0.08 x 10(9) m(3) remain available as natural reservoirs for storing water and sediment, while similar to 0.19 x 10(9) m(3), i.e. about a third of the total river-blocking debris volume, has been eroded by rivers. Dam volume and upstream catchment area control to first order the longevity of the barriers, and bivariate domain plots are consistent with the observation that most earthquake-triggered landslide dams were ephemeral. We conclude that the river-blocking portion of coseismic slope failures disproportionately modulates the post-seismic sediment flux in the Longmen Shan on annual to decadal timescales.}, language = {en} } @article{GorumvanWestenKorupetal.2013, author = {Gorum, Tolga and van Westen, Cees J. and Korup, Oliver and van der Meijde, Mark and Fan, Xuanmei and van der Meer, Freek D.}, title = {Complex rupture mechanism and topography control symmetry of mass-wasting pattern, 2010 Haiti earthquake}, series = {GEOMORPHOLOGY}, volume = {184}, journal = {GEOMORPHOLOGY}, publisher = {ELSEVIER SCIENCE BV}, address = {AMSTERDAM}, issn = {0169-555X}, doi = {10.1016/j.geomorph.2012.11.027}, pages = {127 -- 138}, year = {2013}, abstract = {The 12 January 2010 M-w 7.0 Haiti earthquake occurred in a complex deformation zone at the boundary between the North American and Caribbean plates. Combined geodetic, geological and seismological data posited that surface deformation was driven by rupture on the Leogane blind thrust fault, while part of the rupture occurred as deep lateral slip on the Enriquillo-Plantain Garden Fault (EPGF). The earthquake triggered >4490 landslides, mainly shallow, disrupted rock falls, debris-soil falls and slides, and a few lateral spreads, over an area of similar to 2150 km(2). The regional distribution of these slope failures defies those of most similar earthquake-triggered landslide episodes reported previously. Most of the coseismic landslides did not proliferate in the hanging wall of the main rupture, but clustered instead at the junction of the blind Leogane and EPGF ruptures, where topographic relief and hillslope steepness are above average. Also, low-relief areas subjected to high coseismic uplift were prone to lesser hanging wall slope instability than previous studies would suggest. We argue that a combined effect of complex rupture dynamics and topography primarily control this previously rarely documented landslide pattern. Compared to recent thrust fault-earthquakes of similar magnitudes elsewhere, we conclude that lower static stress drop, mean fault displacement, and blind ruptures of the 2010 Haiti earthquake resulted in fewer, smaller, and more symmetrically distributed landslides than previous studies would suggest. Our findings caution against overly relying on across-the-board models of slope stability response to seismic ground shaking. (C) 2012 Elsevier B.V. All rights reserved.}, language = {en} }