TY - JOUR A1 - Evsevleev, Sergei A1 - Mishurova, Tatiana A1 - Cabeza, Sandra A1 - Koos, R. A1 - Sevostianov, Igor A1 - Garcés, Gonzales A1 - Requena, Guillermo A1 - Fernandez, R. A1 - Bruno, Giovanni T1 - The role of intermetallics in stress partitioning and damage evolution of AlSil2CuMgNi alloy JF - Materials Science and Engineering: A-Structural materials: properties, microstructure and processing N2 - Load partitioning between phases in a cast AlSi12CuMgNi alloy was investigated by in-situ compression test during neutron diffraction experiments. Computed tomography (CT) was used to determine volume fractions of eutectic Si and intermetallic (IM) phases, and to assess internal damage after ex-situ compression tests. The CT reconstructed volumes showed the interconnectivity of IM phases, which build a 3D network together with eutectic Si. Large stresses were found in IMs, revealing their significant role as a reinforcement for the alloy. An existing micromechanical model based on Maxwell scheme was extended to the present case, assuming the alloy as a three-phase composite (Al matrix, eutectic Si, IM phases). The model agrees well with the experimental data. Moreover, it allows predicting the principal stresses in each phase, while experiments can only determine stress differences between the axial and radial sample directions. Finally, we showed that the addition of alloying elements not only allowed developing a 3D interconnected network, but also improved the strength of the Al matrix, and the ability of the alloy constituents to bear mechanical load. KW - Aluminum alloys KW - Neutron diffraction KW - Micromechanical modeling KW - Internal stress KW - Damage KW - Computed tomography Y1 - 2018 U6 - https://doi.org/10.1016/j.msea.2018.08.070 SN - 0921-5093 SN - 1873-4936 VL - 736 SP - 453 EP - 464 PB - Elsevier CY - Lausanne ER - TY - JOUR A1 - Evsevleev, Sergei A1 - Paciornik, Sidnei A1 - Bruno, Giovanni T1 - Advanced deep learning-based 3D microstructural characterization of multiphase metal matrix composites JF - Advanced engineering materials N2 - The quantitative analysis of microstructural features is a key to understanding the micromechanical behavior of metal matrix composites (MMCs), which is a premise for their use in practice. Herein, a 3D microstructural characterization of a five-phase MMC is performed by synchrotron X-ray computed tomography (SXCT). A workflow for advanced deep learning-based segmentation of all individual phases in SXCT data is shown using a fully convolutional neural network with U-net architecture. High segmentation accuracy is achieved with a small amount of training data. This enables extracting unprecedently precise microstructural parameters (e.g., volume fractions and particle shapes) to be input, e.g., in micromechanical models. KW - computed tomography KW - convolutional neural networks KW - deep learning KW - metal KW - matrix composites KW - segmentations Y1 - 2020 U6 - https://doi.org/10.1002/adem.201901197 SN - 1438-1656 SN - 1527-2648 VL - 22 IS - 4 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Mishurova, Tatiana A1 - Bruno, Giovanni A1 - Evsevleev, Sergei A1 - Sevostianov, Igor T1 - Determination of macroscopic stress from diffraction experiments BT - a critical discussion JF - Journal of applied physics N2 - The paper is motivated by some inconsistencies and contradictions present in the literature on the calculation of the so-called diffraction elastic constants. In an attempt at unifying the views that the two communities of Materials Science and Mechanics of Materials have on the subject, we revisit and define the terminology used in the field. We also clarify the limitations of the commonly used approaches and show that a unified methodology is also applicable to textured materials with a nearly arbitrary grain shape. We finally compare the predictions based on this methodology with experimental data obtained by in situ synchrotron radiation diffraction on additively manufactured Ti-6Al-4V alloy. We show that (a) the transverse isotropy of the material yields good agreement between the best-fit isotropy approximation (equivalent to the classic Kroner's model) and the experimental data and (b) the use of a general framework allows the calculation of all components of the tensor of diffraction elastic constants, which are not easily measurable by diffraction methods. This allows us to extend the current state-of-the-art with a predictive tool. Y1 - 2020 U6 - https://doi.org/10.1063/5.0009101 SN - 0021-8979 SN - 1089-7550 VL - 128 IS - 2 PB - American Institute of Physics CY - Melville ER - TY - JOUR A1 - Chen, Cong A1 - Müller, Bernd R. A1 - Prinz, Carsten A1 - Stroh, Julia A1 - Feldmann, Ines A1 - Bruno, Giovanni T1 - The correlation between porosity characteristics and the crystallographic texture in extruded stabilized aluminium titanate for diesel particulate filter applications JF - Journal of the European Ceramic Society N2 - Porous ceramic diesel particulate filters (DPFs) are extruded products that possess macroscopic anisotropic mechanical and thermal properties. This anisotropy is caused by both morphological features (mostly the orientation of porosity) and crystallographic texture. We systematically studied those two aspects in two aluminum titanate ceramic materials of different porosity using mercury porosimetry, gas adsorption, electron microscopy, X-ray diffraction, and X-ray refraction radiography. We found that a lower porosity content implies a larger isotropy of both the crystal texture and the porosity orientation. We also found that, analogous to cordierite, crystallites do align with their axis of negative thermal expansion along the extrusion direction. However, unlike what found for cordierite, the aluminium titanate crystallite form is such that a more pronounced (0 0 2) texture along the extrusion direction implies porosity aligned perpendicular to it. KW - preferred orientation KW - X-ray refraction KW - pore orientation KW - crystal KW - structure KW - extrusion KW - microstructure-property relations Y1 - 2020 U6 - https://doi.org/10.1016/j.jeurceramsoc.2019.11.076 SN - 0955-2219 SN - 1873-619X VL - 40 IS - 4 SP - 1592 EP - 1601 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Thiede, Tobias A1 - Cabeza, Sandra A1 - Mishurova, Tatiana A1 - Nadammal, Naresh A1 - Kromm, Arne A1 - Bode, Johannes A1 - Haberland, Christoph A1 - Bruno, Giovanni T1 - Residual Stress in Selective Laser Melted Inconel 718 BT - Influence of the Removal from Base Plate and Deposition Hatch Length JF - Materials performance and characterization N2 - The residual stress distribution in IN718 elongated prisms produced by selective laser melting was studied by means of neutron (bulk) and laboratory X-ray (surface) diffraction. Two deposition hatch lengths were considered. A horizontal plane near the top surface (perpendicular to the building direction) and a vertical plane near the lateral surface (parallel to the building direction) were investigated. Samples both in as-built (AB) condition and removed from the base plate (RE) were characterized. While surface stress fields seem constant for the AB condition, X-ray diffraction shows stress gradients along the hatch direction in the RE condition. The stress profiles correlate with the distortion maps obtained by tactile probe measurements. Neutron diffraction shows bulk stress gradients for all principal components along the main sample directions. We correlate the observed stress patterns with the hatch length, i.e., with its effect on temperature gradients and heat flow. The bulk stress gradients partially disappear after removal from the base plate. KW - residual stress KW - IN718 KW - neutron diffraction KW - laboratory x-ray diffraction KW - additive manufacturing KW - selective laser melting KW - coordinate measurement machine Y1 - 2018 U6 - https://doi.org/10.1520/MPC20170119 SN - 2379-1365 SN - 2165-3992 VL - 7 IS - 4 SP - 717 EP - 735 PB - American Society for Testing and Materials CY - West Conshohocken ER - TY - JOUR A1 - Erdmann, Maren A1 - Kupsch, Andreas A1 - Müller, Bernd Randolf A1 - Hentschel, Manfred P. A1 - Niebergall, Ute A1 - Böhning, Martin A1 - Bruno, Giovanni T1 - Diesel-induced transparency of plastically deformed high-density polyethylene JF - Journal of materials science N2 - High-density polyethylene becomes optically transparent during tensile drawing when previously saturated with diesel fuel. This unusual phenomenon is investigated as it might allow conclusions with respect to the material behavior. Microscopy, differential scanning calorimetry, density measurements are applied together with two scanning X-ray scattering techniques: wide angle X-ray scattering (WAXS) and X-ray refraction, able to extract the spatially resolved crystal orientation and internal surface, respectively. The sorbed diesel softens the material and significantly alters the yielding characteristics. Although the crystallinity among stretched regions is similar, a virgin reference sample exhibits strain whitening during stretching, while the diesel-saturated sample becomes transparent. The WAXS results reveal a pronounced fiber texture in the tensile direction in the stretched region and an isotropic orientation in the unstretched region. This texture implies the formation of fibrils in the stretched region, while spherulites remain intact in the unstretched parts of the specimens. X-ray refraction reveals a preferred orientation of internal surfaces along the tensile direction in the stretched region of virgin samples, while the sample stretched in the diesel-saturated state shows no internal surfaces at all. Besides from stretching saturated samples, optical transparency is also obtained from sorbing samples in diesel after stretching. Y1 - 2019 U6 - https://doi.org/10.1007/s10853-019-03700-8 SN - 0022-2461 SN - 1573-4803 VL - 54 IS - 17 SP - 11739 EP - 11755 PB - Springer CY - New York ER - TY - JOUR A1 - Mack, Daniel Emil A1 - Laquai, Rene A1 - Mueller, Bernd A1 - Helle, Oliver A1 - Sebold, Doris A1 - Vassen, Robert A1 - Bruno, Giovanni T1 - Evolution of porosity, crack density, and CMAS penetration in thermal barrier coatings subjected to burner rig testing JF - Journal of the American Ceramic Society N2 - Degradation of thermal barrier coatings (TBCs) in gas-turbine engines due to calcium-magnesium-aluminosilicate (CMAS) glassy deposits from various sources has been a persistent issue since many years. In this study, state of the art electron microscopy was correlated with X-ray refraction techniques to elucidate the intrusion of CMAS into the porous structure of atmospheric plasma sprayed (APS) TBCs and the formation and growth of cracks under thermal cycling in a burner rig. Results indicate that the sparse nature of the infiltration as well as kinetics in the burner rig are majorly influenced by the wetting behavior of the CMAS. Despite the obvious attack of CMAS on grain boundaries, the interaction of yttria-stabilized zirconia (YSZ) with intruded CMAS has no immediate impact on structure and density of internal surfaces. At a later stage the formation of horizontal cracks is observed in a wider zone of the TBC layer. KW - characterization KW - CMAS KW - synchrotron X-ray refraction radiography KW - thermal barrier coatings Y1 - 2019 U6 - https://doi.org/10.1111/jace.16465 SN - 0002-7820 SN - 1551-2916 VL - 102 IS - 10 SP - 6163 EP - 6175 PB - Wiley CY - Hoboken ER - TY - JOUR A1 - Mishurova, Tatiana A1 - Artzt, Katia A1 - Haubrich, Jan A1 - Requena, Guillermo A1 - Bruno, Giovanni T1 - New aspects about the search for the most relevant parameters optimizing SLM materials JF - Additive manufacturing N2 - While the volumetric energy density is commonly used to qualify a process parameter set, and to quantify its influence on the microstructure and performance of additively manufactured (AM) materials and components, it has been already shown that this description is by no means exhaustive. In this work, new aspects of the optimization of the selective laser melting process are investigated for AM Ti-6Al-4V. We focus on the amount of near-surface residual stress (RS), often blamed for the failure of components, and on the porosity characteristics (amount and spatial distribution). First, using synchrotron x-ray diffraction we show that higher RS in the subsurface region is generated if a lower energy density is used. Second, we show that laser de-focusing and sample positioning inside the build chamber also play an eminent role, and we quantify this influence. In parallel, using X-ray Computed Tomography, we observe that porosity is mainly concentrated in the contour region, except in the case where the laser speed is small. The low values of porosity (less than 1%) do not influence RS. KW - SLM KW - Ti-6Al-4V KW - X-ray synchrotron diffraction KW - Computed tomography KW - Residual stress Y1 - 2018 U6 - https://doi.org/10.1016/j.addma.2018.11.023 SN - 2214-8604 SN - 2214-7810 VL - 25 SP - 325 EP - 334 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Stegemann, Robert A1 - Cabeza, Sandra A1 - Pelkner, Matthias A1 - Lyamkin, Viktor A1 - Pittner, Andreas A1 - Werner, Daniel A1 - Wimpory, Robert A1 - Boin, Mirko A1 - Kreutzbruck, Marc A1 - Bruno, Giovanni T1 - Influence of the microstructure on magnetic stray fields of low-carbon steel welds JF - Journal of Nondestructive Evaluation N2 - This study examines the relationship between the magnetic mesostructure with the microstructure of low carbon steel tungsten inert gas welds. Optical microscopy revealed variation in the microstructure of the parent material, in the heat affected and fusion zones, correlating with distinctive changes in the local magnetic stray fields measured with high spatial resolution giant magneto resistance sensors. In the vicinity of the heat affected zone high residual stresses were found using neutron diffraction. Notably, the gradients of von Mises stress and triaxial magnetic stray field modulus follow the same tendency transverse to the weld. In contrast, micro-X-ray fluorescence characterization indicated that local changes in element composition had no independent effect on magnetic stray fields. KW - TIG-welding KW - GMR sensors KW - Magnetic stray field KW - Neutron diffraction KW - Residual stress KW - Microstructure KW - Low carbon steel Y1 - 2018 U6 - https://doi.org/10.1007/s10921-018-0522-0 SN - 0195-9298 SN - 1573-4862 VL - 37 IS - 3 PB - Springer CY - New York ER - TY - JOUR A1 - Fernandez, R. A1 - Cabeza, Sandra A1 - Mishurova, Tatiana A1 - Fernandez-Castrillo, P. A1 - Gonzalez-Doncel, Gaspar A1 - Bruno, Giovanni T1 - Residual stress and yield strength evolution with annealing treatments in an age-hardenable aluminum alloy matrix composite JF - Materials Science and Engineering: A N2 - We investigated the possibility of minimizing tensile matrix residual stresses in age hardenable aluminum alloy metal matrix composites without detrimentally affect their mechanical properties (such as yield strength). Specifically, we performed thermal treatments at different temperatures and times in an age-hardenable aluminum matrix composite 2014Al-15vol%Al2O3. Using X-ray synchrotron radiation diffraction and mechanical tests, we show that below a certain treatment temperature (250 degrees C) it is possible to identify an appropriate thermal treatment capable of relaxing residual stress in this composite while even increasing its yield strength, with respect to the as processed conditions. KW - Residual stress KW - Yield strength KW - Annealing treatment KW - Metal matrix composite KW - Diffraction Y1 - 2018 U6 - https://doi.org/10.1016/j.msea.2018.06.031 SN - 0921-5093 SN - 1873-4936 VL - 731 SP - 344 EP - 350 PB - Elsevier CY - Lausanne ER - TY - JOUR A1 - Buljak, Vladimir A1 - Bruno, Giovanni T1 - Numerical modeling of thermally induced microcracking in porous ceramics BT - an approach using cohesive elements JF - Journal of the European Ceramic Society N2 - A numerical framework is developed to study the hysteresis of elastic properties of porous ceramics as a function of temperature. The developed numerical model is capable of employing experimentally measured crystallographic orientation distribution and coefficient of thermal expansion values. For realistic modeling of the microstructure, Voronoi polygons are used to generate polycrystalline grains. Some grains are considered as voids, to simulate the material porosity. To model intercrystalline cracking, cohesive elements are inserted along grain boundaries. Crack healing (recovery of the initial properties) upon closure is taken into account with special cohesive elements implemented in the commercial code ABAQUS. The numerical model can be used to estimate fracture properties governing the cohesive behavior through inverse analysis procedure. The model is applied to a porous cordierite ceramic. The obtained fracture properties are further used to successfully simulate general non-linear macroscopic stress-strain curves of cordierite, thereby validating the model. KW - analysis KW - Cohesive finite elements KW - Interfacial strength Y1 - 2018 U6 - https://doi.org/10.1016/j.jeurceramsoc.2018.03.041 SN - 0955-2219 SN - 1873-619X VL - 38 IS - 11 SP - 4099 EP - 4108 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Sevostianov, Igor A1 - Bruno, Giovanni T1 - Maxwell scheme for internal stresses in multiphase composites JF - Mechanics of Materials N2 - The paper focuses on the reformulation of classic Maxwell's (1873) homogenization method for calculation of the residual stresses in matrix composites. For this goal, we equate the far fields produced by a set of inhomogeneities subjected to known eigenstrains and by a fictitious domain with unknown eigenstrain. The effect of interaction between the inhomogeneities is reduced to the calculation of the additional field acting on an inhomogeneity due to the eigenstrains in its neighbors. An explicit formula for residual stresses is derived for the general case of a multiphase composite. The method is illustrated by several examples. The results are compared with available experimental data as well as with predictions provided by the non-interaction approximation (Eshelby solution). It is shown that accounting for interaction can explain many experimentally observed phenomena and is required for adequate quantitative analytical modeling of the residual stresses in matrix composites. KW - Residual stress KW - Multiphase composites KW - Interaction KW - Micromechanical schemes KW - Anisotropy Y1 - 2018 U6 - https://doi.org/10.1016/j.mechmat.2018.12.005 SN - 0167-6636 SN - 1872-7743 VL - 129 SP - 320 EP - 331 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Fernandez, Ricardo A1 - Bruno, Giovanni A1 - Garces, Gerardo A1 - Nieto-Luis, H. A1 - Gonzalez-Doncel, Gaspar T1 - Fractional brownian motion of dislocations during creep deformation of metals JF - Materials science & engineering. A, Structural materials N2 - The present work offers an explanation on how the long-range interaction of dislocations influences their movement, and therefore the strain, during creep of metals. It is proposed that collective motion of dislocations can be described as a fractional Brownian motion. This explains the noisy appearance of the creep strain signal as a function of time. Such signal is split into a deterministic and a stochastic part. These terms can be related to two kinds of dislocation motions: individual and collective, respectively. The description is consistent with the fractal nature of strain-induced dislocation structures predicated in previous works. Moreover, it encompasses the evolution of the strain rate during all stages of creep, including the tertiary one. Creep data from Al99.8% and Al3.85%Mg tested at different temperatures and stresses are used to validate the proposed ideas: it is found that different creep stages present different diffusion characters, and therefore different dislocation motion character. KW - Creep KW - Aluminum alloys KW - Dislocation motion KW - Diffusion KW - Fractal KW - structures Y1 - 2020 U6 - https://doi.org/10.1016/j.msea.2020.140013 SN - 0921-5093 SN - 1873-4936 VL - 796 PB - Elsevier CY - Lausanne ER - TY - JOUR A1 - Laquai, Rene A1 - Müller, Bernd R. A1 - Schneider, Judith Ann A1 - Kupsch, Andreas A1 - Bruno, Giovanni T1 - Using SXRR to probe the nature of discontinuities in SLM additive manufactured inconel 718 specimens JF - Metallurgical and Materials Transactions A N2 - The utilization of additive manufacturing (AM) to fabricate robust structural components relies on understanding the nature of internal anomalies or discontinuities, which can compromise the structural integrity. While some discontinuities in AM microstructures stem from similar mechanisms as observed in more traditional processes such as casting, others are unique to the AM process. Discontinuities in AM are challenging to detect, due to their submicron size and orientation dependency. Toward the goal of improving structural integrity, minimizing discontinuities in an AM build requires an understanding of the mechanisms of formation to mitigate their occurrence. This study utilizes various techniques to evaluate the shape, size, nature and distribution of discontinuities in AM Inconel 718, in a non-hot isostatic pressed (HIPed) as-built, non-HIPed and direct age, and HIPed with two step age samples. Non-destructive synchrotron radiation refraction and transmission radiography (SXRR) provides additional information beyond that obtained with destructive optical microscopy. SXRR was able to distinguish between voids, cracks and lack of melt in, due to its sensitivity to the orientation of the discontinuity. Y1 - 2020 U6 - https://doi.org/10.1007/s11661-020-05847-5 SN - 1073-5623 SN - 1543-1940 VL - 51 IS - 8 SP - 4146 EP - 4157 PB - Springer CY - New York ER - TY - JOUR A1 - Fernandez, Ricardo A1 - Gonzalez-Doncel, Gaspar A1 - Garces, Gerardo A1 - Bruno, Giovanni T1 - Towards a comprehensive understanding of creep BT - microstructural dependence of the pre-exponential term in Al JF - Materials science & engineering. A, Structural materials: properties, microstructure and processing N2 - We show that the equation proposed by Takeuchi and Argon to explain the creep behavior of Al-Mg solid solution can be used to describe also the creep behavior of pure aluminum. In this frame, it is possible to avoid the use of the classic pre-exponential fitting parameter in the power law equation to predict the minimum creep strain rate. The effect of the fractal arrangement of dislocations, developed at the mesoscale, must be considered to fully explain the experimental data. These ideas allow improving the recently introduced SSTC model, fully describing the primary and secondary creep regimes of aluminum alloys without the need for fitting. Creep data from commercially pure A199.8% and Al-Mg alloys tested at different temperatures and stresses are used to validate the proposed ideas. KW - creep KW - Aluminum alloys KW - dislocations KW - fractal KW - stress exponent Y1 - 2020 U6 - https://doi.org/10.1016/j.msea.2020.139036 SN - 0921-5093 SN - 1873-4936 VL - 776 PB - Elsevier CY - Lausanne ER - TY - JOUR A1 - Laquai, Rene A1 - Gouraud, Fanny A1 - Müller, Bernd Randolf A1 - Huger, Marc A1 - Chotard, Thierry A1 - Antou, Guy A1 - Bruno, Giovanni T1 - Evolution of Thermal Microcracking in Refractory ZrO2-SiO2 after Application of External Loads at High Temperatures JF - Materials N2 - Zirconia-based cast refractories are widely used for glass furnace applications. Since they have to withstand harsh chemical as well as thermo-mechanical environments, internal stresses and microcracking are often present in such materials under operating conditions (sometimes in excess of 1700 °C). We studied the evolution of thermal (CTE) and mechanical (Young’s modulus) properties as a function of temperature in a fused-cast refractory containing 94 wt.% of monoclinic ZrO2 and 6 wt.% of a silicate glassy phase. With the aid of X-ray refraction techniques (yielding the internal specific surface in materials), we also monitored the evolution of microcracking as a function of thermal cycles (crossing the martensitic phase transformation around 1000 °C) under externally applied stress. We found that external compressive stress leads to a strong decrease of the internal surface per unit volume, but a tensile load has a similar (though not so strong) effect. In agreement with existing literature on β-eucryptite microcracked ceramics, we could explain these phenomena by microcrack closure in the load direction in the compression case, and by microcrack propagation (rather than microcrack nucleation) under tensile conditions. KW - electro-fused zirconia KW - microcracking KW - synchrotron x-ray refraction radiography (SXRR) KW - thermal expansion Y1 - 2019 U6 - https://doi.org/10.3390/ma12071017 SN - 1996-1944 VL - 12 IS - 7 PB - MDPI CY - Basel ER - TY - JOUR A1 - Nadammal, Naresh A1 - Cabeza, Sandra A1 - Mishurova, Tatiana A1 - Thiede, Tobias A1 - Kromm, Arne A1 - Seyfert, Christoph A1 - Farahbod, Lena A1 - Haberland, Christoph A1 - Schneider, Judith Ann A1 - Portella, Pedro Dolabella A1 - Bruno, Giovanni T1 - Effect of hatch length on the development of microstructure, texture and residual stresses in selective laser melted superalloy Inconel 718 JF - Materials & Design N2 - In the present study, samples fabricated by varying the deposition hatch length during selective laser melting of nickel based superalloy Inconel 718 were investigated. Microstructure and texture of these samples was characterized using scanning electron microscopy, combined with electron back-scattered diffraction, and residual stress assessment, using neutron diffraction method. Textured columnar grains oriented along the sample building direction were observed in the shorter hatch length processed sample. A ten-fold increase in the hatch length reduced the texture intensity by a factor of two attributed to the formation of finer grains in the longer hatch length sample. Larger gradients of transverse residual stress in the longer hatch length sample were also observed. Along the build direction, compressive stresses in the shorter hatch length and negligible stresses for the longer hatch length specimen were observed. Changes to the temperature gradient (G) in response to the hatch length variation, influenced the G to growth rate (R) ratio and the product GxR, in agreement with the microstructures and textures formed. For the residual stress development, geometry of the part also played an important role. In summary, tailored isotropy could be induced in Inconel 718 by a careful selection of parameters during selective laser melting. KW - Additive manufacturing KW - Nickel-based superalloy KW - Microstructure and texture KW - Residual stress KW - Electron back-scattered diffraction KW - Neutron diffraction Y1 - 2017 U6 - https://doi.org/10.1016/j.matdes.2017.08.049 SN - 0264-1275 SN - 1873-4197 VL - 134 SP - 139 EP - 150 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Mishurova, Tatiana A1 - Artzt, Katia A1 - Haubrich, Jan A1 - Requena, Guillermo A1 - Bruno, Giovanni T1 - Exploring the correlation between subsurface residual stresses and manufacturing parameters in laser powder bed fused Ti-6Al-4V JF - Metals N2 - Subsurface residual stresses (RS) were investigated in Ti-6Al-4V cuboid samples by means of X-ray synchrotron diffraction. The samples were manufactured by laser powder bed fusion (LPBF) applying different processing parameters, not commonly considered in open literature, in order to assess their influence on RS state. While investigating the effect of process parameters used for the calculation of volumetric energy density (such as laser velocity, laser power and hatch distance), we observed that an increase of energy density led to a decrease of RS, although not to the same extent for every parameter variation. Additionally, the effect of support structure, sample roughness and LPBF machine effects potentially coming from Ar flow were studied. We observed no influence of support structure on subsurface RS while the orientation with respect to Ar flow showed to have an impact on RS. We conclude recommending monitoring such parameters to improve part reliability and reproducibility. KW - residual stress KW - synchrotron X-ray diffraction KW - additive manufacturing KW - Ti-6Al-4V Y1 - 2019 U6 - https://doi.org/10.3390/met9020261 SN - 2075-4701 VL - 9 IS - 2 PB - MDPI CY - Basel ER - TY - JOUR A1 - Chen, Cong A1 - Müller, Bernd Randolf A1 - Lebedev, Oleg I. A1 - Giovannelli, Fabien A1 - Bruno, Giovanni A1 - Delorme, Fabian T1 - Effects of impurities on the stability of the low thermal conductivity in Fe2TiO5 ceramics JF - Materials characterization N2 - The stability of the low thermal conductivity in Fe2TiO5 pseudobrookite ceramics has been studied. An increase in thermal diffusivity is observed after only three cycles of measurement. X-ray refraction shows an increase in the mean value of specific surface after the thermal diffusivity measurements. By using scanning electron microscopy and high-angle annular dark-field scanning transmission electron microscope equipped with energy dispersive Xray spectroscopy, we observe a segregation of Ca- and F-rich nanocrystals at grain boundaries after three cycles of thermal diffusivity measurement. Therefore, impurities seem to be more efficient to scatter phonons as point defects in the pseudobrookite lattice rather than as nanocrystals at pseudobrookite grain boundaries. This emphasizes the importance of precursor purity and the influence of redistribution of impurities on thermoelectric properties: stability of micro-/nano-structures is a key point, and repeated thermoelectric measurements may allow detecting such metastable micro-/nano-structures and producing stable and reliable data. KW - Fe2TiO5 KW - Impurity segregation KW - Thermoclectrics KW - X-ray refraction KW - Scanning transmission electron microscopy KW - Thermal conductivity Y1 - 2019 U6 - https://doi.org/10.1016/j.matchar.2019.01.021 SN - 1044-5803 SN - 1873-4189 VL - 149 SP - 111 EP - 117 PB - Elsevier CY - New York ER - TY - JOUR A1 - Bruno, Giovanni A1 - Kachanov, Mark A1 - Sevostianov, Igor A1 - Shyam, Amit T1 - Micromechanical modeling of non-linear stress-strain behavior of polycrystalline microcracked materials under tension JF - Acta materialia N2 - The stress-strain behavior of microcracked polycrystalline materials (such as ceramics or rocks) under conditions of tensile, displacement-controlled, loading is discussed. Micromechanical explanation and modeling of the basic features, such as non-linearity and hysteresis in stress-strain curves, is developed, with stable microcrack propagation and "roughness" of intergranular cracks playing critical roles. Experiments involving complex loading histories were done on large- and medium grain size beta-eucryptite ceramic. The model is shown to reproduce the basic features of the observed stress-strain curves. (C) 2018 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved. KW - Nonlinearity KW - Stress-strain relations KW - Hysteresis KW - Tension KW - Ceramics KW - Rocks KW - Polycrystals Y1 - 2018 U6 - https://doi.org/10.1016/j.actamat.2018.10.024 SN - 1359-6454 SN - 1873-2453 VL - 164 SP - 50 EP - 59 PB - Elsevier CY - Oxford ER -