TY - JOUR A1 - Albrecht, Steve A1 - Grootoonk, Bjorn A1 - Neubert, Sebastian A1 - Roland, Steffen A1 - Wordenweber, Jan A1 - Meier, Matthias A1 - Schlatmann, Rutger A1 - Gordijn, Aad A1 - Neher, Dieter T1 - Efficient hybrid inorganic/organic tandem solar cells with tailored recombination contacts JF - Solar energy materials & solar cells : an international journal devoted to photovoltaic, photothermal, and photochemical solar energy conversion N2 - In this work, the authors present a 7.5% efficient hybrid tandem solar cell with the bottom cell made of amorphous silicon and a Si-PCPDTBT:PC70BM bulk heterojunction top cell. Loss-free recombination contacts were realized by combing Al-doped ZnO with either the conducting polymer composite PEDOT:PSS or with a bilayer of ultrathin Al and MoO3. Optimization of these contacts results in tandem cells with high fill factors of 70% and an open circuit voltage close to the sum of those of the sub-cells. This is the best efficiency reported for this type of hybrid tandem cell so far. Optical and electrical device modeling suggests that the efficiency can be increased to similar to 12% on combining a donor polymer with suitable absorption onset with PCBM. We also describe proof-of-principle studies employing light trapping in hybrid tandem solar cells, suggesting that this device architecture has the potential to achieve efficiencies well above 12%. (C) 2014 Elsevier B.V. All rights reserved. KW - Hybrid solar cells KW - Tandem solar cells KW - Organic solar cells KW - Bulk heterojunction KW - Efficiency optimization Y1 - 2014 U6 - https://doi.org/10.1016/j.solmat.2014.04.020 SN - 0927-0248 SN - 1879-3398 VL - 127 SP - 157 EP - 162 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Braunger, Steffen A1 - Mundt, Laura E. A1 - Wolff, Christian Michael A1 - Mews, Mathias A1 - Rehermann, Carolin A1 - Jost, Marko A1 - Tejada, Alvaro A1 - Eisenhauer, David A1 - Becker, Christiane A1 - Andres Guerra, Jorge A1 - Unger, Eva A1 - Korte, Lars A1 - Neher, Dieter A1 - Schubert, Martin C. A1 - Rech, Bernd A1 - Albrecht, Steve T1 - Cs(x)FA(1-x)Pb(l(1-y)Br(y))(3) Perovskite Compositions BT - the Appearance of Wrinkled Morphology and its Impact on Solar Cell Performance JF - The journal of physical chemistry : C, Nanomaterials and interfaces N2 - We report on the formation of wrinkle-patterned surface morphologies in cesium formamidinium-based Cs(x)FA(1-y)Pb(I1-yBry)(3) perovskite compositions with x = 0-0.3 and y = 0-0.3 under various spin-coating conditions. By varying the Cs and Br contents, the perovskite precursor solution concentration and the spin-coating procedure, the occurrence and characteristics of the wrinkle-shaped morphology can be tailored systematically. Cs(0.17)FA(0.83)Pb(I0.83Br0.17)(3) perovskite layers were analyzed regarding their surface roughness, microscopic structure, local and overall composition, and optoelectronic properties. Application of these films in p-i-n perovskite solar cells (PSCs) with indium-doped tin oxide/NiOx/perovskite/C-60/bathocuproine/Cu architecture resulted in up to 15.3 and 17.0% power conversion efficiency for the flat and wrinkled morphology, respectively. Interestingly, we find slightly red-shifted photoluminescence (PL) peaks for wrinkled areas and we are able to directly correlate surface topography with PL peak mapping. This is attributed to differences in the local grain size, whereas there is no indication for compositional demixing in the films. We show that the perovskite composition, crystallization kinetics, and layer thickness strongly influence the formation of wrinkles which is proposed to be related to the release of compressive strain during perovskite crystallization. Our work helps us to better understand film formation and to further improve the efficiency of PSCs with widely used mixed-perovskite compositions. Y1 - 2018 U6 - https://doi.org/10.1021/acs.jpcc.8b06459 SN - 1932-7447 SN - 1932-7455 VL - 122 IS - 30 SP - 17123 EP - 17135 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Kegelmann, Lukas A1 - Tockhorn, Philipp A1 - Wolff, Christian Michael A1 - Márquez, José A. A1 - Caicedo Dávila, Sebastián A1 - Korte, Lars A1 - Unold, Thomas A1 - Loevenich, Wilfried A1 - Neher, Dieter A1 - Rech, Bernd A1 - Albrecht, Steve T1 - Mixtures of Dopant-Free Spiro-OMeTAD and Water-Free PEDOT as a Passivating Hole Contact in Perovskite Solar Cells JF - ACS applied materials & interfaces N2 - Doped spiro-OMeTAD at present is the most commonly used hole transport material (HTM) in n-i-p-type perovskite solar cells, enabling high efficiencies around 22%. However, the required dopants were shown to induce nonradiative recombination of charge carriers and foster degradation of the solar cell. Here, in a novel approach, highly conductive and inexpensive water-free poly(3,4-ethylenedioxythiophene) (PEDOT) is used to replace these dopants. The resulting spiro-OMeTAD/PEDOT (SpiDOT) mixed films achieve higher lateral conductivities than layers of doped spiro-OMeTAD. Furthermore, combined transient and steady-state photoluminescence studies reveal a passivating effect of PEDOT, suppressing nonradiative recombination losses at the perovskite/HTM interface. This enables excellent quasi-Fermi level splitting values of up to 1.24 eV in perovskite/SpiDOT layer stacks and high open-circuit voltages (V-OC) up to 1.19 V in complete solar cells. Increasing the amount of dopant-free spiro-OMeTAD in SpiDOT layers is shown to enhance hole extraction and thereby improves the fill factor in solar cells. As a consequence, stabilized efficiencies up to 18.7% are realized, exceeding cells with doped spiro-OMeTAD as a HTM in this study. Moreover, to the best of our knowledge, these results mark the lowest nonradiative recombination loss in the V-OC (140 mV with respect to the Shockley-Queisser limit) and highest efficiency reported so far for perovskite solar cells using PEDOT as a HTM. KW - perovskite solar cell KW - selective contact KW - spiro-OMeTAD KW - PEDOT KW - recombination KW - passivation KW - quasi-Fermi level splitting Y1 - 2019 U6 - https://doi.org/10.1021/acsami.9b01332 SN - 1944-8244 SN - 1944-8252 VL - 11 IS - 9 SP - 9172 EP - 9181 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Fischer, Florian S. U. A1 - Trefz, Daniel A1 - Back, Justus A1 - Kayunkid, Navaphun A1 - Tornow, Benjamin A1 - Albrecht, Steve A1 - Yager, Kevin G. A1 - Singh, Gurpreet A1 - Karim, Alamgir A1 - Neher, Dieter A1 - Brinkmann, Martin A1 - Ludwigs, Sabine T1 - Highly Crystalline Films of PCPDTBT with Branched Side Chains by Solvent Vapor Crystallization: Influence on Opto-Electronic Properties JF - Advanced materials N2 - PCPDTBT, a marginally crystallizable polymer, is crystallized into a new crystal structure using solvent-vapor annealing. Highly ordered areas with three different polymer-chain orientations are identified using TEM/ED, GIWAXS, and polarized Raman spectroscopy. The optical and structural properties differ significantly from films prepared by standard device preparation protocols. Bilayer solar cells, however, show similar performance. Y1 - 2015 U6 - https://doi.org/10.1002/adma.201403475 SN - 0935-9648 SN - 1521-4095 VL - 27 IS - 7 SP - 1223 EP - 1228 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Albrecht, Steve A1 - Vandewal, Koen A1 - Tumbleston, John R. A1 - Fischer, Florian S. U. A1 - Douglas, Jessica D. A1 - Frechet, Jean M. J. A1 - Ludwigs, Sabine A1 - Ade, Harald W. A1 - Salleo, Alberto A1 - Neher, Dieter T1 - On the efficiency of charge transfer state splitting in polymer: Fullerene solar cells JF - Advanced materials KW - organic solar cells KW - charge generation KW - geminate recombination KW - charge transfer states KW - driving force KW - excess energy KW - morphology KW - spectroelectrochemistry Y1 - 2014 U6 - https://doi.org/10.1002/adma.201305283 SN - 0935-9648 SN - 1521-4095 VL - 26 IS - 16 SP - 2533 EP - 2539 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Albrecht, Steve A1 - Tumbleston, John R. A1 - Janietz, Silvia A1 - Dumsch, Ines A1 - Allard, Sybille A1 - Scherf, Ullrich A1 - Ade, Harald W. A1 - Neher, Dieter T1 - Quantifying charge extraction in organic solar cells: The case of fluorinated PCPDTBT JF - The journal of physical chemistry letters N2 - We introduce a new and simple method to quantify the effective extraction mobility in organic solar cells at low electric fields and charge carrier densities comparable to operation conditions under one sun illumination. By comparing steady-state carrier densities at constant illumination intensity and under open-circuit conditions, the gradient of the quasi-Fermi potential driving the current is estimated as a function of external bias and charge density. These properties are then related to the respective steady-state current to determine the effective extraction mobility. The new technique is applied to different derivatives of the well-known low-band-gap polymer PCPDTBT blended with PC70BM. We show that the slower average extraction due to lower mobility accounts for the moderate fill factor when solar cells are fabricated with mono- or difluorinated PCPDTBT. This lower extraction competes with improved generation and reduced nongeminate recombination, rendering the monofluorinated derivative the most efficient donor polymer. Y1 - 2014 U6 - https://doi.org/10.1021/jz500457b SN - 1948-7185 VL - 5 IS - 7 SP - 1131 EP - 1138 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Pradhan, Basudev A1 - Albrecht, Steve A1 - Stiller, Burkhard A1 - Neher, Dieter T1 - Inverted organic solar cells comprising low-temperature-processed ZnO films JF - Applied physics : A, Materials science & processing N2 - Inverted organic solar cells are fabricated using low-temperature-annealed ZnO film as an electron transport layer. Uniform ZnO films were prepared by spin coating a diethylzinc (DEZ) precursor solution in air, followed by annealing at 100 A degrees C. Organic solar cells prepared on these ZnO films with a 1:1 P3HT:PCBM blend as the active layer show a high power conversion efficiency of 4.03 %, which is more than 10 % higher than the PCE of solar cells comprising ZnO prepared via a high-temperature sol-gel route. Y1 - 2014 U6 - https://doi.org/10.1007/s00339-014-8373-8 SN - 0947-8396 SN - 1432-0630 VL - 115 IS - 2 SP - 365 EP - 369 PB - Springer CY - New York ER - TY - JOUR A1 - Roland, Steffen A1 - Neubert, Sebastian A1 - Albrecht, Steve A1 - Stannowski, Bernd A1 - Seger, Mark A1 - Facchetti, Antonio A1 - Schlatmann, Rutger A1 - Rech, Bernd A1 - Neher, Dieter T1 - Hybrid Organic/Inorganic Thin-Film Multijunction Solar Cells Exceeding 11% Power Conversion Efficiency JF - Advanced materials N2 - Hybrid multijunction solar cells comprising hydrogenated amorphous silicon and an organic bulk heterojunction are presented, reaching 11.7% power conversion efficiency. The benefits of merging inorganic and organic subcells are pointed out, the optimization of the cells, including optical modeling predictions and tuning of the recombination contact are described, and an outlook of this technique is given. Y1 - 2015 U6 - https://doi.org/10.1002/adma.201404698 SN - 0935-9648 SN - 1521-4095 VL - 27 IS - 7 SP - 1262 EP - 1267 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Kegelmann, Lukas A1 - Wolff, Christian Michael A1 - Awino, Celline A1 - Lang, Felix A1 - Unger, Eva L. A1 - Korte, Lars A1 - Dittrich, Thomas A1 - Neher, Dieter A1 - Rech, Bernd A1 - Albrecht, Steve T1 - It Takes Two to Tango-Double-Layer Selective Contacts in Perovskite Solar Cells for Improved Device Performance and Reduced Hysteresis JF - ACS applied materials & interfaces N2 - Solar cells made from inorganic organic perovskites have gradually approached market requirements as their efficiency and stability have improved tremendously in recent years. Planar low-temperature processed perovskite solar cells are advantageous for possible large-scale production but are more prone to exhibiting photocurrent hysteresis, especially in the regular n-i-p structure. Here, a systematic characterization of different electron selective contacts with a variety of chemical and electrical properties in planar n-i-p devices processed below 180 degrees C is presented. The inorganic metal oxides TiO2 and SnO2, the organic fullerene derivatives C-60, PCBM, and ICMA, as well as double-layers with a metal oxide/PCBM structure are used as electron transport materials (ETMs). Perovskite layers deposited atop, the different ETMs with the herein applied fabrication method show a similar morphology according to scanning electron microscopy. Further, surface photovoltage spectroscopy measurements indicate comparable perovskite absorber qualities on all ETMs, except TiO2, which shows a more prominent influence of defect states. Transient photoluminescence studies together with current voltage scans over a broad range of scan speeds reveal faster charge extraction, less pronounced hysteresis effects, and higher efficiencies for devices with fullerene compared to those with metal oxide ETMs. Beyond this, only double-layer ETM structures substantially diminish hysteresis effects for all performed scan speeds and strongly enhance the power conversion efficiency up to a champion stabilized value of 18.0%. The results indicate reduced recombination losses for a double-layer TiO2/PCBM contact design: First, a reduction of shunt paths through the fullerene to the ITO layer. Second, an improved hole blocking by the wide band gap metal oxide. Third, decreased transport losses due to an energetically more favorable contact, as implied by photoelectron spectroscopy measurements. The herein demonstrated improvements of multilayer selective contacts may serve as a general design guideline for perovskite solar cells. KW - perovskite solar cell KW - electron contact KW - double-layer KW - regular planar architecture KW - hysteresis KW - fullerene KW - metal oxide Y1 - 2017 U6 - https://doi.org/10.1021/acsami.7b00900 SN - 1944-8244 VL - 9 SP - 17246 EP - 17256 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Jošt, Marko A1 - Albrecht, Steve A1 - Kegelmann, Lukas A1 - Wolff, Christian Michael A1 - Lang, Felix A1 - Lipovšek, Benjamin A1 - Krč, Janez A1 - Korte, Lars A1 - Neher, Dieter A1 - Rech, Bernd A1 - Topič, Marko T1 - Efficient light management by textured nanoimprinted layers for perovskite solar cells JF - ACS photonics N2 - Inorganic-organic perovskites like methylammonium-lead-iodide have proven to be an effective class of 17 materials for fabricating efficient solar cells. To improve their performance, light management techniques using textured surfaces, similar to those used in established solar cell technologies, should be considered. Here, we apply a light management foil created by UV nanoimprint lithography on the glass side of an inverted (p-i-n) perovskite solar cell with 16.3% efficiency. The obtained 1 mA cm(-2) increase in the short-circuit current density translates to a relative improvement in cell performance of 5%, which results in a power conversion efficiency of 17.1%. Optical 3D simulations based on experimentally obtained parameters were used to support the experimental findings. A good match between the simulated and experimental data was obtained, validating the model. Optical simulations reveal that the main improvement in device performance is due to a reduction in total reflection and that relative improvement in the short-circuit current density of up to 10% is possible for large-area devices. Therefore, our results present the potential of light management foils for improving the device performance of perovskite solar cells and pave the way for further use of optical simulations in the field of perovskite solar cells. KW - perovskite solar cells KW - antireflection KW - light management KW - UV nanoimprint lithography KW - optical simulations Y1 - 2017 U6 - https://doi.org/10.1021/acsphotonics.7b00138 SN - 2330-4022 VL - 4 SP - 1232 EP - 1239 PB - American Chemical Society CY - Washington ER -