TY - JOUR A1 - Heidbach, Oliver A1 - Rajabi, Mojtaba A1 - Cui, Xiaofeng A1 - Fuchs, Karl A1 - Mueller, Birgit A1 - Reinecker, John A1 - Reiter, Karsten A1 - Tingay, Mark A1 - Wenzel, Friedemann A1 - Xie, Furen A1 - Ziegler, Moritz O. A1 - Zoback, Mary-Lou A1 - Zoback, Mark T1 - The World Stress Map database release 2016 BT - Crustal stress pattern across scales JF - Tectonophysics : international journal of geotectonics and the geology and physics of the interior of the earth N2 - Knowledge of the present-day crustal in-situ stress field is a key for the understanding of geodynamic processes such as global plate tectonics and earthquakes. It is also essential for the management of geo-reservoirs and underground storage sites for energy and waste. Since 1986, the World Stress Map (WSM) project has systematically compiled the orientation of maximum horizontal stress (S-Hmax). For the 30th anniversary of the project, the WSM database has been updated significantly with 42,870 data records which is double the amount of data in comparison to the database release in 2008. The update focuses on areas with previously sparse data coverage to resolve the stress pattern on different spatial scales. In this paper, we present details of the new WSM database release 2016 and an analysis of global and regional stress pattern. With the higher data density, we can now resolve stress pattern heterogeneities from plate-wide to local scales. In particular, we show two examples of 40 degrees-60 degrees S-Hmax rotations within 70 km. These rotations can be used as proxies to better understand the relative importance of plate boundary forces that control the long wave-length pattern in comparison to regional and local controls of the crustal stress state. In the new WSM project phase IV that started in 2017, we will continue to further refine the information on the S-Hmax orientation and the stress regime. However, we will also focus on the compilation of stress magnitude data as this information is essential for the calibration of geomechanical-numerical models. This enables us to derive a 3-D continuous description of the stress tensor from point-wise and incomplete stress tensor information provided with the WSM database. Such forward models are required for safety aspects of anthropogenic activities in the underground and for a better understanding of tectonic processes such as the earthquake cycle. KW - Tectonic stress KW - Database KW - Stress tensor KW - Geomechanical modelling Y1 - 2018 U6 - https://doi.org/10.1016/j.tecto.2018.07.007 SN - 0040-1951 SN - 1879-3266 VL - 744 SP - 484 EP - 498 PB - Elsevier CY - Amsterdam ER - TY - GEN A1 - Ziegler, Moritz O. A1 - Heidbach, Oliver A1 - Reinecker, John A1 - Przybycin, Anna M. A1 - Scheck-Wenderoth, Magdalena T1 - A multi-stage 3-D stress field modelling approach exemplified in the Bavarian Molasse Basin T2 - Postprints der Universität Potsdam Mathematisch-Naturwissenschaftliche Reihe N2 - The knowledge of the contemporary in situ stress state is a key issue for safe and sustainable subsurface engineering. However, information on the orientation and magnitudes of the stress state is limited and often not available for the areas of interest. Therefore 3-D geomechanical-numerical modelling is used to estimate the in situ stress state and the distance of faults from failure for application in subsurface engineering. The main challenge in this approach is to bridge the gap in scale between the widely scattered data used for calibration of the model and the high resolution in the target area required for the application. We present a multi-stage 3-D geomechanical-numerical approach which provides a state-of-the-art model of the stress field for a reservoir-scale area from widely scattered data records. Therefore, we first use a large-scale regional model which is calibrated by available stress data and provides the full 3-D stress tensor at discrete points in the entire model volume. The modelled stress state is used subsequently for the calibration of a smaller-scale model located within the large-scale model in an area without any observed stress data records. We exemplify this approach with two-stages for the area around Munich in the German Molasse Basin. As an example of application, we estimate the scalar values for slip tendency and fracture potential from the model results as measures for the criticality of fault reactivation in the reservoir-scale model. The modelling results show that variations due to uncertainties in the input data are mainly introduced by the uncertain material properties and missing S-Hmax magnitude estimates needed for a more reliable model calibration. This leads to the conclusion that at this stage the model's reliability depends only on the amount and quality of available stress information rather than on the modelling technique itself or on local details of the model geometry. Any improvements in modelling and increases in model reliability can only be achieved using more high-quality data for calibration. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 556 KW - in-situ stress KW - induced seismicity KW - geothermal-reservoirs KW - geomechanical model KW - fault reactivation KW - alpine foreland KW - map project KW - km depth KW - orientation KW - system Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-409806 SN - 1866-8372 IS - 556 ER - TY - JOUR A1 - Ziegler, Moritz O. A1 - Heidbach, Oliver A1 - Reinecker, John A1 - Przybycin, Anna M. A1 - Scheck-Wenderoth, Magdalena T1 - A multi-stage 3-D stress field modelling approach exemplified in the Bavarian Molasse Basin JF - Solid earth Y1 - 2016 U6 - https://doi.org/10.5194/se-7-1365-2016 SN - 1869-9510 SN - 1869-9529 VL - 7 SP - 1365 EP - 1382 PB - Copernicus CY - Göttingen ER -