TY - JOUR A1 - Gulyakova, Anna A. A1 - Gorokhovatsky, Yuri A. A1 - frübing, Peter A1 - Gerhard, Reimund T1 - Relaxation Processes Determining the Electret Stability of High-Impact Polystyrene/Titanium-Dioxide Composite Films JF - IEEE transactions on dielectrics and electrical insulation N2 - The influence of relaxation processes on the thermal electret stability of high-impact polystyrene (HIPS) free-standing films filled with titanium dioxide (TiO2) of the rutile modification are investigated by means of a combination of dielectric methods (dielectric relaxation spectroscopy (DRS), thermally stimulated depolarization current (TSDC) and thermally stimulated surface-potential decay (TSSPD)), supplemented by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Films with 2, 4, 6 and 8 vol.% TiO2 are compared to each other and to non-filled samples. Filling HIPS with up to 8 vol.% of TiO2 enhances the elastic modulus below the glass transition and increases the thermal electret stability above the glass transition without significantly increasing the DC conductivity. The improvement of the electret stability is caused by the build-up of an interface polarization which decays only gradually if the glass transition is exceeded. Two kinds of Arrhenius processes are considered in order to explain the decay of the composite-polymer electrets: (1) charge release from chemical traps located at the phenyl rings of the polymer chain with an activation energy of E-a = 1.1 eV after passing the glass transition at about 100 degrees C and (2) charge release from traps formed by the TiO2 particles with E-a = 2.4 eV at temperatures above 130 degrees C. Finally, the activation energies are discussed with respect to their significance. KW - High-impact polystyrene KW - titanium dioxide KW - electret stability KW - dielectric relaxation Y1 - 2017 U6 - https://doi.org/10.1109/TDEI.2017.006587 SN - 1070-9878 SN - 1558-4135 VL - 24 SP - 2541 EP - 2548 PB - Inst. of Electr. and Electronics Engineers CY - Piscataway ER - TY - JOUR A1 - Wang, Jingwen A1 - Rychkov, Dmitry A1 - Gerhard, Reimund T1 - Chemical modification with orthophosphoric acid enhances surface-charge stability on polypropylene electrets JF - Applied physics letters N2 - The low surface-charge stability of polypropylene (PP) frequently limits its application as an electret material. In this paper, we demonstrate how the treatment of PP-film surfaces with orthophosphoric acid (H3PO4) enhances their charge stability. To discriminate between the effects of chemical modification and thermal treatment, as-received and annealed PP films are used as reference samples. The electret properties of treated and non-treated PP films are characterized with thermally stimulated discharge (TSD) and isothermal surface-potential decay (ISPD) experiments, from which considerable improvement in thermal and temporal charge stability is observed for samples modified with H3PO4. The half-value temperature (T-1/2) observed on TSD curves of chemically treated PP increases to 131 and 145 degrees C for positive and negative charges, respectively. The enhancement might be attributed to the phosphoric compounds detected on the H3PO4-modified surfaces via attenuated-total-reflection infrared spectroscopy. Deeper surface traps formed at the "foreign" phosphorus-containing structures are able to capture the charges over longer time periods and at higher temperatures, thus leading to significant improvements in the temporal and thermal surface-charge stabilities of PP electrets. Published by AIP Publishing. Y1 - 2017 U6 - https://doi.org/10.1063/1.4983348 SN - 0003-6951 SN - 1077-3118 VL - 110 PB - American Institute of Physics CY - Melville ER - TY - JOUR A1 - Fang, Peng A1 - Ma, Xingchen A1 - Li, Xiangxin A1 - Qiu, Xunlin A1 - Gerhard, Reimund A1 - Zhang, Xiaoqing A1 - Li, Guanglin T1 - Fabrication, Structure Characterization, and Performance Testing of Piezoelectret-Film Sensors for Recording Body Motion JF - IEEE Sensors Journal N2 - During muscle contractions, radial-force distributions are generated on muscle surfaces due to muscle-volume changes, from which the corresponding body motions can be recorded by means of so-called force myography (FMG). Piezo- or ferroelectrets are flexible piezoelectric materials with attractive materials and sensing properties. In addition to several other applications, they are suitable for detecting force variations by means of wearable devices. In this paper, we prepared piezoelectrets from cellular polypropylene films by optimizing the fabrication procedures, and developed an FMG-recording system based on piezoelectret sensors. Different hand and wrist movements were successfully detected on able-bodied subjects with the FMG system. The FMG patterns were evaluated and identified by means of linear discriminant analysis and artificial neural network algorithms, and average motion-classification accuracies of 96.1% and 94.8%, respectively, were obtained. This paper demonstrates the feasibility of using piezoelectret-film sensors for FMG and may thus lead to alternative methods for detecting body motion and to related applications, e.g., in biomedical engineering or structural-health monitoring. KW - Forcemyography KW - motion registration KW - piezoelectret KW - film sensor KW - wearable Y1 - 2017 U6 - https://doi.org/10.1109/JSEN.2017.2766663 SN - 1530-437X SN - 1558-1748 VL - 18 IS - 1 SP - 401 EP - 412 PB - Inst. of Electr. and Electronics Engineers CY - Piscataway ER - TY - GEN A1 - Loupos, Konstantinos A1 - Damigos, Yannis A1 - Amditis, Angelos A1 - Gerhard, Reimund A1 - Rychkov, Dmitry A1 - Wirges, Werner A1 - Schulze, Manuel A1 - Lenas, Sotiris-Angelos A1 - Chatziandreoglou, Christos A1 - Malliou, Christina A1 - Tsaoussidis, Vassilis A1 - Brady, Ken A1 - Frankenstein, Bernd T1 - Structural health monitoring system for bridges based on skin-like sensor T2 - IOP conference series : Materials science and engineering N2 - Structural health monitoring activities are of primal importance for managing transport infrastructure, however most SHM methodologies are based on point-based sensors that have limitations in terms of their spatial positioning requirements, cost of development and measurement range. This paper describes the progress on the SENSKIN EC project whose objective is to develop a dielectric-elastomer and micro-electronics-based sensor, formed from a large highly extensible capacitance sensing membrane supported by advanced microelectronic circuitry, for monitoring transport infrastructure bridges. Such a sensor could provide spatial measurements of strain in excess of 10%. The actual sensor along with the data acquisition module, the communication module and power electronics are all integrated into a compact unit, the SENSKIN device, which is energy-efficient, requires simple signal processing and it is easy to install over various surface types. In terms of communication, SENSKIN devices interact with each other to form the SENSKIN system; a fully distributed and autonomous wireless sensor network that is able to self-monitor. SENSKIN system utilizes Delay-/Disruption-Tolerant Networking technologies to ensure that the strain measurements will be received by the base station even under extreme conditions where normal communications are disrupted. This paper describes the architecture of the SENSKIN system and the development and testing of the first SENSKIN prototype sensor, the data acquisition system, and the communication system. Y1 - 2017 U6 - https://doi.org/10.1088/1757-899X/236/1/012100 SN - 1757-8981 VL - 236 PB - IOP Publ. Ltd. CY - Bristol ER -