TY - JOUR A1 - Neffe, Axel T. A1 - Loebus, Axel A1 - Zaupa, Alessandro A1 - Stötzel, Christian A1 - Müller, Frank A. A1 - Lendlein, Andreas T1 - Gelatin functionalization with tyrosine derived moieties to increase the interaction with hydroxyapatite fillers JF - Acta biomaterialia N2 - Combining gelatins functionalized with the tyrosine-derived groups desaminotyrosine or desaminotyrosyl tyrosine with hydroxyapatite (HAp) led to the formation of composite materials with much lower swelling ratios than those of the pure matrices. Shifts of the infra-red (IR) bands related to the free carboxyl groups could be observed in the presence of HAp, which suggested a direct interaction of matrix and filler that formed additional physical cross-links in the material. In tensile tests and rheological measurements the composites equilibrated in water had increased Young's moduli (from 200 kPa up to 2 MPa) and tensile strengths (from 57 kPa up to 1.1 MPa) compared with the matrix polymers without affecting the elongation at break. Furthermore, an increased thermal stability of the networks from 40 to 85 degrees C could be demonstrated. The differences in the behaviour of the functionalized gelatins compared with pure gelatin as a matrix suggested an additional stabilizing bond between the incorporated aromatic groups and the HAp as supported by the IR results. The composites can potentially be applied as bone fillers. KW - Gelatin KW - Hydroxyapatite KW - Composite KW - Hydrogel KW - Biomaterial Y1 - 2011 U6 - https://doi.org/10.1016/j.actbio.2010.11.025 SN - 1742-7061 VL - 7 IS - 4 SP - 1693 EP - 1701 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Neffe, Axel T. A1 - Zhang, Quanchao A1 - Hommes-Schattmann, Paul J. A1 - Lendlein, Andreas T1 - Ethylene oxide sterilization of electrospun poly(L-lactide)/poly(D-lactide) core/shell nanofibers JF - MRS advances N2 - The application of polymers in medicine requires sterilization while retaining material structure and properties. This demands detailed analysis, which we show exemplarily for the sterilization of PLLA/PDLA core-shell nanofibers with ethylene oxide (EtO). The electrospun patch was exposed to EtO gas (6 vol% in CO2, 1.7 bar) for 3 h at 45 degrees C and 75% rel. humidity, followed by degassing under pressure/vacuum cycles for 12 h. GC-MS analysis showed that no residual EtO was retained. Fiber diameters (similar to 520 +/- 130 nm) of the patches remained constant as observed by electron microscopy. Young's modulus slightly increased and the elongation at break slightly decreased, determined at 37 degrees C. No changes were detected in H-1-NMR spectra, in molar mass distribution (GPC) or in crystallinity measured for annealed samples with comparable thermal history (Wide Angle X-Ray Scattering). Altogether, EtO emerged as suitable sterilization method for polylactide nanofibers with core-shell morphology. Y1 - 2021 U6 - https://doi.org/10.1557/s43580-021-00058-5 SN - 2059-8521 VL - 6 IS - 33 SP - 786 EP - 789 PB - Springer CY - Cham ER - TY - JOUR A1 - Zou, Jie A1 - Wang, Weiwei A1 - Neffe, Axel T. A1 - Xu, Xun A1 - Li, Zhengdong A1 - Deng, Zijun A1 - Sun, Xianlei A1 - Ma, Nan A1 - Lendlein, Andreas T1 - Adipogenic differentiation of human adipose derived mesenchymal stem cells in 3D architectured gelatin based hydrogels (ArcGel) JF - Clinical hemorheology and microcirculation : blood flow and vessels N2 - Polymeric matrices mimicking multiple functions of the ECM are expected to enable a material induced regeneration of tissues. Here, we investigated the adipogenic differentiation of human adipose derived mesenchymal stem cells (hADSCs) in a 3D architectured gelatin based hydrogel (ArcGel) prepared from gelatin and L-lysine diisocyanate ethyl ester (LDI) in an one-step process, in which the formation of an open porous morphology and the chemical network formation were integrated. The ArcGel was designed to support adipose tissue regeneration with its 3D porous structure, high cell biocompatibility, and mechanical properties compatible with human subcutaneous adipose tissue. The ArcGel could support initial cell adhesion and survival of hADSCs. Under static culture condition, the cells could migrate into the inner part of the scaffold with a depth of 840 +/- 120 mu m after 4 days, and distributed in the whole scaffold (2mm in thickness) within 14 days. The cells proliferated in the scaffold and the fold increase of cell number after 7 days of culture was 2.55 +/- 0.08. The apoptotic rate of hADSCs in the scaffold was similar to that of cells maintained on tissue culture plates. When cultured in adipogenic induction medium, the hADSCs in the scaffold differentiated into adipocytes with a high efficiency (93 +/- 1%). Conclusively, this gelatin based 3D scaffold presented high cell compatibility for hADSC cultivation and differentiation, which could serve as a potential implant material in clinical applications for adipose tissue reparation and regeneration. KW - Mesenchymal stem cells KW - gelatin based scaffold KW - adipose tissue regeneration KW - adipogenic differentiation Y1 - 2017 U6 - https://doi.org/10.3233/CH-179210 SN - 1386-0291 SN - 1875-8622 VL - 67 IS - 3-4 SP - 297 EP - 307 PB - IOS Press CY - Amsterdam ER - TY - JOUR A1 - Izraylit, Victor A1 - Hommes-Schattmann, Paul Jacob A1 - Neffe, Axel T. A1 - Gould, Oliver E. C. A1 - Lendlein, Andreas T1 - Alkynyl-functionalized chain-extended PCL for coupling to biological molecules JF - European polymer journal N2 - Chemical functionalization of poly(epsilon-caprolactone) (PCL) enables a molecular integration of additional function. Here, we report an approach to incorporate reactive alkynyl side-groups by synthesizing a chain-extended PCL, where the reactive site is introduced through the covalently functionalizable chain extender 3 (prop-2-yn-1-yloxy)propane-1,2-diol (YPD). Chain-extended PCL with M-w of 101 to 385 kg.mol(-1) were successfully synthesized in a one-pot reaction from PCL-diols with various molar masses, L-lysine ethyl ester diisocyanate (LDI) or trimethyl(hexamethylene)diisocyanate (TMDI), and YPD, in which the density of functionalizable groups and spacing between them can be controlled by the composition of the polymer. The employed diisocyanate compounds and YPD possess an asymmetric structure and form a non-crystallizable segment leaving the PCL crystallites to dominate the material's mechanical properties. The mixed glass transition temperature T-g = - 60 to - 46 degrees C of the PCL/polyurethane amorphous phase maintains the synthesized materials in a highly elastic state at ambient and physiological conditions. Reaction conditions for covalent attachment in copper(I)-catalyzed azide-alkyne-cycloaddition reactions (CuAAC) in solution were optimized in a series of model reactions between the alkyne moieties of the chain-extended PCL and benzyl azide, reaching conversions over 95% of the alkyne moieties and with yields of up to 94% for the purified functionalized PCL. This methodology was applied for reaction with the azide-functionalized cell adhesion peptide GRGDS. The required modification of the peptide provides selectivity in the coupling reactions. The obtained results suggest that YPD could potentially be employed as versatile molecular unit for the creation of a variety of functionalizable polyesters as well as polyurethanes and polycarbonates offering efficient and selective click-reactions. KW - copper-catalyzed alkyne-azide cycloaddition KW - chain-extended KW - polycaprolactone KW - RGD-peptide KW - side-chains functionalization Y1 - 2020 U6 - https://doi.org/10.1016/j.eurpolymj.2020.109908 SN - 0014-3057 SN - 1873-1945 VL - 136 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Neffe, Axel T. A1 - Izraylit, Victor A1 - Hommes-Schattmann, Paul J. A1 - Lendlein, Andreas T1 - Soft, formstable (Co)polyester blend elastomers JF - Nanomaterials : open access journal N2 - High crystallization rate and thermomechanical stability make polylactide stereocomplexes effective nanosized physical netpoints. Here, we address the need for soft, form-stable degradable elastomers for medical applications by designing such blends from (co)polyesters, whose mechanical properties are ruled by their nanodimensional architecture and which are applied as single components in implants. By careful controlling of the copolymer composition and sequence structure of poly[(L-lactide)-co-(epsilon-caprolactone)], it is possible to prepare hyperelastic polymer blends formed through stereocomplexation by adding poly(D-lactide) (PDLA). Low glass transition temperature T-g <= 0 degrees C of the mixed amorphous phase contributes to the low Young's modulus E. The formation of stereocomplexes is shown in DSC by melting transitions T-m > 190 degrees C and in WAXS by distinct scattering maxima at 2 theta = 12 degrees and 21 degrees. Tensile testing demonstrated that the blends are soft (E = 12-80 MPa) and show an excellent hyperelastic recovery R-rec = 66-85% while having high elongation at break epsilon(b) up to >1000%. These properties of the blends are attained only when the copolymer has 56-62 wt% lactide content, a weight average molar mass >140 kg center dot mol(-1), and number average lactide sequence length >= 4.8, while the blend is formed with a content of 5-10 wt% of PDLA. The devised strategy to identify a suitable copolymer for stereocomplexation and blend formation is transferable to further polymer systems and will support the development of thermoplastic elastomers suitable for medical applications. KW - thermoplastic elastomer KW - biomaterial KW - stereocomplexes KW - mechanical KW - properties KW - form stability KW - crystallinity Y1 - 2021 U6 - https://doi.org/10.3390/nano11061472 SN - 2079-4991 VL - 11 IS - 6 PB - MDPI CY - Basel ER - TY - JOUR A1 - Izraylit, Victor A1 - Hommes-Schattmann, Paul J. A1 - Neffe, Axel T. A1 - Gould, Oliver E. C. A1 - Lendlein, Andreas T1 - Polyester urethane functionalizable through maleimide side-chains and cross-linkable by polylactide stereocomplexes JF - European polymer journal N2 - Sustainable multifunctional alternatives to fossil-derived materials, which can be functionalized and are degradable, can be envisioned by combining naturally derived starting materials with an established polymer design concept. Modularity and chemical flexibility of polyester urethanes (PEU) enable the combination of segments bearing functionalizable moieties and the tailoring of the mechanical and thermal properties. In this work, a PEU multiblock structure was synthesized from naturally derived L-lysine diisocyanate ethyl ester (LDI), poly(L-lactide) diol (PLLA) and N-(2,3-dihydroxypropyl)-maleimide (MID) in a one-step reaction. A maleimide side-chain (MID) provided a reactive site for the catalyst-free coupling of thiols shown for L-cysteine with a yield of 94%. Physical cross-links were generated by blending the PEU with poly(D-lactide) (PDLA), upon which the PLLA segments of the PEU and the PDLA formed stereocomplexes. Stereocomplexation occurred spontaneously during solution casting and was investigated with WAXS and DSC. Stereocomplex crystallites were observed in the blends, while isotactic PLA crystallization was not observed. The presented material platform with tailorable mechanical properties by blending is of specific interest for engineering biointerfaces of implants or carrier systems for bioactive molecules. KW - Functionalization KW - Polylactide stereocomplex KW - Biomolecules coupling Y1 - 2020 U6 - https://doi.org/10.1016/j.eurpolymj.2020.109916 SN - 0014-3057 SN - 1873-1945 VL - 137 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Wang, Weiwei A1 - Naolou, Toufik A1 - Ma, Nan A1 - Deng, Zijun A1 - Xu, Xun A1 - Mansfeld, Ulrich A1 - Wischke, Christian A1 - Gossen, Manfred A1 - Neffe, Axel T. A1 - Lendlein, Andreas T1 - Polydepsipeptide Block-Stabilized Polyplexes for Efficient Transfection of Primary Human Cells JF - Biomacromolecules : an interdisciplinary journal focused at the interface of polymer science and the biological sciences N2 - The rational design of a polyplex gene carrier aims to balance maximal effectiveness of nucleic acid transfection into cells with minimal adverse effects. Depsipeptide blocks with an M (n) similar to 5 kDa exhibiting strong physical interactions were conjugated with PEI moieties (2.5 or 10 kDa) to di- and triblock copolymers. Upon nanoparticle formation and complexation with DNA, the resulting polyplexes (sizes typically 60-150 nm) showed remarkable stability compared to PEI-only or lipoplex and facilitated efficient gene delivery. Intracellular trafficking was visualized by observing fluorescence-labeled pDNA and highlighted the effective cytoplasmic uptake of polyplexes and release of DNA to the perinuclear space. Specifically, a triblock copolymer with a middle depsipeptide block and two 10 kDa PEI swallowtail structures mediated the highest levels of transgenic VEGF secretion in mesenchymal stem cells with low cytotoxicity. These nanocarriers form the basis for a delivery platform technology, especially for gene transfer to primary human cells. Y1 - 2017 U6 - https://doi.org/10.1021/acs.biomac.7b01034 SN - 1525-7797 SN - 1526-4602 VL - 18 SP - 3819 EP - 3833 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Hommes-Schattmann, Paul J. A1 - Neffe, Axel T. A1 - Ahmad, Bilal A1 - Williams, Gareth R. A1 - Vanneaux, Valerie A1 - Menasche, Philippe A1 - Kalfa, David A1 - Lendlein, Andreas T1 - RGD constructs with physical anchor groups as polymer co-electrospinnable cell adhesives JF - Polymers for advanced technologies N2 - The tissue integration of synthetic polymers can be promoted by displaying RGD peptides at the biointerface with the objective of enhancing colonization of the material by endogenous cells. A firm but flexible attachment of the peptide to the polymer matrix, still allowing interaction with receptors, is therefore of interest. Here, the covalent coupling of flexible physical anchor groups, allowing for temporary immobilization on polymeric surfaces via hydrophobic or dipole-dipole interactions, to a RGD peptide was investigated. For this purpose, a stearate or an oligo(ethylene glycol) (OEG) was attached to GRGDS in 51-69% yield. The obtained RGD linker constructs were characterized by NMR, IR and MALDI-ToF mass spectrometry, revealing that the commercially available OEG and stearate linkers are in fact mixtures of similar compounds. The RGD linker constructs were co-electrospun with poly(p-dioxanone) (PPDO). After electrospinning, nitrogen could be detected on the surface of the PPDO fibers by X-ray photoelectron spectroscopy. The nitrogen content exceeded the calculated value for the homogeneous material mixture suggesting a pronounced presentation of the peptide on the fiber surface. Increasing amounts of RGD linker constructs in the electrospinning solution did not lead to a detection of an increased amount of peptide on the scaffold surface, suggesting inhomogeneous distribution of the peptide on the PPDO fiber surface. Human adipose-derived stem cells cultured on the patches showed similar viability as when cultured on PPDO containing pristine RGD. The fully characterized RGD linker constructs could serve as valuable tools for the further development of tissue-integrating polymeric scaffolds. Copyright (c) 2016 John Wiley & Sons, Ltd. KW - electrospinning KW - RGD peptides KW - cell adhesion KW - biofunctionalization Y1 - 2017 U6 - https://doi.org/10.1002/pat.3963 SN - 1042-7147 SN - 1099-1581 VL - 28 SP - 1312 EP - 1317 PB - Wiley CY - Hoboken ER - TY - JOUR A1 - Naolou, Toufik A1 - Lendlein, Andreas A1 - Neffe, Axel T. T1 - Amides as non-polymerizable catalytic adjuncts enable the ring-opening polymerization of lactide with ferrous acetate under mild conditions JF - Frontiers in Chemistry N2 - Sn-based catalysts are effective in the ring-opening polymerization (ROP) but are toxic. Fe(OAc)(2) used as an alternative catalyst is suitable for the ROP of lactide only at higher temperatures (>170 degrees C), associated with racemization. In the ROP of ester and amide group containing morpholinediones with Fe(OAc)(2) to polydepsipeptides at 135 degrees C, ester bonds were selectively opened. Here, it was hypothesized that ROP of lactones is possible with Fe(OAc)(2) when amides are present in the reactions mixture as Fe-ligands could increase the solubility and activity of the metal catalytic center. The ROP of lactide in the melt with Fe(OAc)(2) is possible at temperatures as low as 105 degrees C, in the presence of N-ethylacetamide or N-rnethylbenzamide as non-polymerizable catalytic adjuncts (NPCA), with high conversion (up to 99 mol%) and yield (up to 88 mol%). Polydispersities of polylactide decreased with decreasing reaction temperature to <= 1.1. NMR as well as polarimetric studies showed that no racemization occurred at reaction temperatures <= 145 degrees C. A kinetic study demonstrated a living chain-growth mechanism. MALDI analysis revealed that no side reactions (e.g., cyclization) occurred, though transesterification took place. KW - ring-opening polymerization KW - polyester KW - catalyst KW - iron KW - amide ligand Y1 - 2019 U6 - https://doi.org/10.3389/fchem.2019.00346 SN - 2296-2646 VL - 7 PB - Frontiers Research Foundation CY - Lausanne ER - TY - JOUR A1 - Piluso, Susanna A1 - Lendlein, Andreas A1 - Neffe, Axel T. T1 - Enzymatic action as switch of bulk to surface degradation of clicked gelatin-based networks JF - Polymers for advanced technologies N2 - Polymer degradation occurs under physiological conditions in vitro and in vivo, especially when bonds susceptible to hydrolysis are present in the polymer. Understanding of the degradation mechanism, changes of material properties over time, and overall rate of degradation is a necessary prerequisite for the knowledge-based design of polymers with applications in biomedicine. Here, hydrolytic degradation studies of gelatin-based networks synthesized by copper-catalyzed azide-alkyne cycloaddition reaction are reported, which were performed with or without addition of an enzyme. In all cases, networks with a stilbene as crosslinker proofed to be more resistant to degradation than when an octyl diazide was used. Without addition of an enzyme, the rate of degradation was ruled by the crosslinking density of the network and proceeded via a bulk degradation mechanism. Addition of Clostridium histolyticum collagenase resulted in a much enhanced rate of degradation, which furthermore occurred via surface erosion. The mesh size of the hydrogels (>7nm) was in all cases larger than the hydrodynamic radius of the enzyme (4.5nm) so that even in very hydrophilic networks with large mesh size enzymes may be used to induce a fast surface degradation mechanism. This observation is of general interest when designing hydrogels to be applied in the presence of enzymes, as the degradation mechanism and material performance are closely interlinked. Copyright (c) 2016 John Wiley & Sons, Ltd. KW - Hydrogel KW - Biopolymer KW - Degradation Y1 - 2017 U6 - https://doi.org/10.1002/pat.3962 SN - 1042-7147 SN - 1099-1581 VL - 28 SP - 1318 EP - 1324 PB - Wiley CY - Hoboken ER -