TY - JOUR A1 - Adebayo, Segun Emmanuel A1 - Hashim, Norhashila A1 - Hass, Roland A1 - Reich, Oliver A1 - Regen, Christian A1 - Münzberg, Marvin A1 - Abdan, Khalina A1 - Hanafi, Marsyita A1 - Zude-Sasse, Manuela T1 - Using absorption and reduced scattering coefficients for non-destructive analyses of fruit flesh firmness and soluble solids content in pear JF - Postharvest Biology and Technology N2 - Quality attributes of fruit determine its acceptability by the retailer and consumer. The objective of this work was to investigate the potential of absorption (μa) and reduced scattering (μs’) coefficients of European pear to analyze its fruit flesh firmness and soluble solids content (SSC). The absolute reference values, μa* (cm−1) and μs’* (cm−1), of pear were invasively measured, employing multi-spectral photon density wave (PDW) spectroscopy at preselected wavelengths of 515, 690, and 940 nm considering two batches of unripe and overripe fruit. On eight measuring dates during fruit development, μa and μs’ were analyzed non-destructively by means of laser light backscattering imaging (LLBI) at similar wavelengths of 532, 660, and 830 nm by means of fitting according to Farrell’s diffusion theory, using fix reference values of either μa* or μs’*. Both, the μa* and the μa as well as μs’* and μs’ showed similar trends. Considering the non-destructively measured data during fruit development, μa at 660 nm decreased 91 till 141 days after full bloom (dafb) from 1.49 cm−1 to 0.74 cm−1 due to chlorophyll degradation. At 830 nm, μa only slightly decreased from 0.41 cm−1 to 0.35 cm−1. The μs’ at all wavelengths revealed a decreasing trend as the fruit developed. The difference measured at 532 nm was most pronounced decreasing from 24 cm−1 to 10 cm−1, while at 660 nm and 830 nm values decreased from 15 cm−1 to 13 cm−1 and from 10 cm−1 to 8 cm−1, respectively. When building calibration models with partial least-squares regression analysis on the optical properties for non-destructive analysis of the fruit SSC, μa at 532 nm and 830 nm resulted in a correlation coefficient of R = 0.66, however, showing high measuring uncertainty. The combination of all three wavelengths gave an enhanced, encouraging R = 0.89 for firmness analysis using μs’ in the freshly picked fruit. KW - Absorption KW - Non-destructive KW - Pear KW - Quality KW - Scattering Y1 - 2017 U6 - https://doi.org/10.1016/j.postharvbio.2017.04.004 SN - 0925-5214 SN - 1873-2356 VL - 130 SP - 56 EP - 63 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Ruiz, Salome Vargas A1 - Hass, Roland A1 - Reich, Oliver T1 - Optical monitoring of milk fat phase transition within homogenized fresh milk by Photon Density Wave spectroscopy JF - International dairy journal N2 - Photon Density Wave (PDW) spectroscopy was applied for temperature dependent monitoring of melting and crystallization of milk fat within homogenized fresh milk. As an in-line process analytical technique, PDW spectroscopy quantifies continuously the optical properties of turbid material, providing an insight into its structural processes. Here, the measured absorption coefficients reflect temperature as well as fat content of milk and the reduced scattering coefficients probe physical changes of the light scattering fat droplets and casein micelles. Thermal processing reveals breakpoints within the temperature trend of the reduced scattering coefficient of fat containing milk. Found at 16 degrees C and 24 degrees C while cooling and heating, respectively, they are associated to the phase transitions of milk fat. Continuous isothermal measurement of the optical coefficients showed that the crystallization process requires several hours. The strongly changing reduced scattering coefficient implies that the thermal history of milk will have a major impact on any method based on light scattering as quantitative analytical technique. Y1 - 2012 U6 - https://doi.org/10.1016/j.idairyj.2012.03.012 SN - 0958-6946 VL - 26 IS - 2 SP - 120 EP - 126 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Hass, Roland A1 - Reich, Oliver T1 - Photon density wave spectroscopy for dilution-free sizing of highly concentrated nanoparticles during starved-feed polymerization JF - ChemPhysChem : a European journal of chemical physics and physical chemistry KW - analytical methods KW - fiber-optical spectroscopy KW - nanoparticles KW - photon density wave spectroscopy KW - polymerization Y1 - 2011 U6 - https://doi.org/10.1002/cphc.201100323 SN - 1439-4235 VL - 12 IS - 14 SP - 2572 EP - 2575 PB - Wiley-Blackwell CY - Malden ER - TY - JOUR A1 - Hass, Roland A1 - Munzke, Dorit A1 - Reich, Oliver T1 - Inline-Partikelgroeßenmesstechniken fuer Suspensionen und Emulsionen N2 - Die Inline-Bestimmung von Teilchengroeßen in Emulsionen und Suspensionen stellt besondere Anforderungen an die Messtechnik, da auch bei sehr hohen Teilchenkonzentrationen im Prozess verduennungsfreie Analytik betrieben werden soll. Neben einer Klaerung der Begriffe atline, online und in-line gibt der Beitrag eine Einfuehrung in die mathematische Beschreibung von Groeßenverteilungen. Als Inline-Techniken werden Photonendichtewellen-Spektroskopie, Focused Beam Reflectance Measurement und Ultraschallextinktion-Spektroskopie diskutiert und ihre sehr unterschiedlichen physikalischen Messprinzipien erlaeutert. Auch wird kurz erklaert, wie Teilchengroeßen aus den Messresultaten erhalten werden. Die wesentlichen Charakteristika dieser drei Methoden werden abschließend im ueberblick dargestellt. Y1 - 2010 UR - http://www3.interscience.wiley.com/cgi-bin/jhome/60500203/ U6 - https://doi.org/10.1002/cite.200900172 SN - 0009-286X ER - TY - GEN A1 - Hass, Roland A1 - Sandmann, Michael A1 - Reich, Oliver T1 - Photonic sensing in highly concentrated biotechnical processes by photon density wave spectroscopy T2 - Proceedings SPIE 10323, 25th International Conference on Optical Fiber Sensors N2 - Photon Density Wave (PDW) spectroscopy is introduced as a new approach for photonic sensing in highly concentrated biotechnical processes. It independently quantifies the absorption and reduced scattering coefficient calibration-free and as a function of time, thus describing the optical properties in the vis/NIR range of the biomaterial during their processing. As examples of industrial relevance, enzymatic milk coagulation, beer mashing, and algae cultivation in photo bioreactors are discussed. KW - Photon Density Wave Spectroscopy KW - multiple light scattering KW - fermentation KW - algae cultivation KW - process analytical technology KW - fiber spectroscopy Y1 - 2017 SN - 978-1-5090-4850-2 U6 - https://doi.org/10.1117/12.2263617 SN - 0277-786X SN - 1996-756X VL - 10323 PB - IEEE CY - New York ER - TY - GEN A1 - Münzberg, Marvin A1 - Hass, Roland A1 - Khanh, Ninh Dinh Duc A1 - Reich, Oliver T1 - Limitations of turbidity process probes and formazine as their calibration standard T2 - Postprints der Universität Potsdam : Mathematisch Naturwissenschaftliche Reihe N2 - Turbidity measurements are frequently implemented for the monitoring of heterogeneous chemical, physical, or biotechnological processes. However, for quantitative measurements, turbidity probes need calibration, as is requested and regulated by the ISO 7027:1999. Accordingly, a formazine suspension has to be produced. Despite this regulatory demand, no scientific publication on the stability and reproducibility of this polymerization process is available. In addition, no characterization of the optical properties of this calibration material with other optical methods had been achieved so far. Thus, in this contribution, process conditions such as temperature and concentration have been systematically investigated by turbidity probe measurements and Photon Density Wave (PDW) spectroscopy, revealing an influence on the temporal formazine formation onset. In contrast, different reaction temperatures do not lead to different scattering properties for the final formazine suspensions, but give an access to the activation energy for this condensation reaction. Based on PDW spectroscopy data, the synthesis of formazine is reproducible. However, very strong influences of the ambient conditions on the measurements of the turbidity probe have been observed, limiting its applicability. The restrictions of the turbidity probe with respect to scatterer concentration are examined on the basis of formazine and polystyrene suspensions. Compared to PDW spectroscopy data, signal saturation is observed at already low reduced scattering coefficients. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 831 KW - photon density wave spectroscopy KW - turbidity probes KW - formazine KW - calibration standard KW - process analytical technology Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-428263 SN - 1866-8372 IS - 831 ER - TY - JOUR A1 - Hass, Roland A1 - Munzke, Dorit A1 - Ruiz, Salome Vargas A1 - Tippmann, Johannes A1 - Reich, Oliver T1 - Optical monitoring of chemical processes in turbid biogenic liquid dispersions by Photon Density Wave spectroscopy JF - Analytical & bioanalytical chemistry N2 - In turbid biogenic liquid material, like blood or milk, quantitative optical analysis is often strongly hindered by multiple light scattering resulting from cells, particles, or droplets. Here, optical attenuation is caused by losses due to absorption as well as scattering of light. Fiber-based Photon Density Wave (PDW) spectroscopy is a very promising method for the precise measurement of the optical properties of such materials. They are expressed as absorption and reduced scattering coefficients (mu (a) and mu (s)', respectively) and are linked to the chemical composition and physical properties of the sample. As a process analytical technology, PDW spectroscopy can sense chemical and/or physical processes within such turbid biogenic liquids, providing new scientific insight and process understanding. Here, for the first time, several bioprocesses are analyzed by PDW spectroscopy and the resulting optical coefficients are discussed with respect to established mechanistic models of the chosen processes. As model systems, enzymatic casein coagulation in milk, temperature-induced starch hydrolysis in beer mash, and oxy- as well as deoxygenation of human donor blood were investigated by PDW spectroscopy. The findings indicate that also for very complex biomaterials (i.e., not well-defined model materials like monodisperse polymer dispersions), obtained optical coefficients allow for the assessment of a structure/process relationship and thus for a new analytical access to biogenic liquid material. This is of special relevance as PDW spectroscopy data are obtained without any dilution or calibration, as often found in conventional spectroscopic approaches. KW - Photon Density Wave spectroscopy KW - Enzymatic milk coagulation KW - Beer mashing KW - Human donor blood KW - Process analytical technology KW - Light scattering Y1 - 2015 U6 - https://doi.org/10.1007/s00216-015-8513-9 SN - 1618-2642 SN - 1618-2650 VL - 407 IS - 10 SP - 2791 EP - 2802 PB - Springer CY - Heidelberg ER - TY - JOUR A1 - Hartwig, Anne A1 - Hass, Roland T1 - Monitoring lactose crystallization at industrially relevant concentrations by photon density wave spectroscopy JF - Chemical engineering & technology N2 - Lactose is of great industrial importance and its production includes the cooling crystallization from highly concentrated solutions. Monitoring the crystallization process is essential to ensure reproducible product quality. Photon density wave (PDW) spectroscopy enables in-line monitoring of highly concentrated processes in liquid dispersions. It was applied to the determination of the solubility and nucleation points of lactose monohydrate in water, sizing of lactose crystals, and to dissolution as well as crystallization monitoring. Other process analytical technologies (focused-beam reflectance measurement, particle vision and measurement) were used as reference, and the comparison indicates that PDW spectroscopy is very robust against probe fouling and is, thus, a useful tool for monitoring crystallization processes in concentrated suspensions. KW - In-line monitoring KW - Lactose KW - Light scattering KW - Photon density wave spectroscopy KW - Process analytical technology Y1 - 2018 U6 - https://doi.org/10.1002/ceat.201700685 SN - 0930-7516 SN - 1521-4125 VL - 41 IS - 6 SP - 1139 EP - 1146 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Polley, Nabarun A1 - Basak, Supratim A1 - Hass, Roland A1 - Pacholski, Claudia T1 - Fiber optic plasmonic sensors BT - Providing sensitive biosensor platforms with minimal lab equipment JF - Biosensors and bioelectronics : the principal international journal devoted to research, design development and application of biosensors and bioelectronics N2 - A simple, convenient, and inexpensive method to fabricate optical fiber based biosensors which utilize periodic hole arrays in gold films for signal transduction is reported. The process of hole array formation mainly relies on self-assembly of hydrogel microgels in combination with chemical gold film deposition and subsequent transfer of the perforated film onto an optical fiber tip. In the fabrication process solely chemical wet lab techniques are used, avoiding cost-intensive instrumentation or clean room facilities. The presented method for preparing fiber optic plasmonic sensors provides high throughput and is perfectly suited for commercialization using batch processing. The transfer of the perforated gold film onto an optical fiber tip does not affect the sensitivity of the biosensor ((420 +/- 83) nm/refractive index unit (RIU)), which is comparable to sensitivities of sensor platforms based on periodic hole arrays in gold films prepared by significantly more complex methods. Furthermore, real-time and in-line immunoassay studies with a specially designed 3D printed flow cell are presented exploiting the presented optical fiber based biosensors. KW - Surface plasmon resonance KW - Optical fiber KW - Bottom-up fabrication KW - Biosensor KW - 3D printed flow-cell Y1 - 2019 U6 - https://doi.org/10.1016/j.bios.2019.03.020 SN - 0956-5663 SN - 1873-4235 VL - 132 SP - 368 EP - 374 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Zude-Sasse, Manuela A1 - Hashim, Norhashila A1 - Hass, Roland A1 - Polley, Nabarun A1 - Regen, Christian T1 - Validation study for measuring absorption and reduced scattering coefficients by means of laser-induced backscattering imaging JF - Postharvest Biology and Technology N2 - Decoupling of optical properties appears challenging, but vital to get better insight of the relationship between light and fruit attributes. In this study, nine solid phantoms capturing the ranges of absorption (μa) and reduced scattering (μs’) coefficients in fruit were analysed non-destructively using laser-induced backscattering imaging (LLBI) at 1060 nm. Data analysis of LLBI was carried out on the diffuse reflectance, attenuation profile obtained by means of Farrell’s diffusion theory either calculating μa [cm−1] and μs’ [cm−1] in one fitting step or fitting only one optical variable and providing the other one from a destructive analysis. The nondestructive approach was approved when calculating one unknown coefficient non-destructively, while no ability of the method was found to analysis both, μa and μs’, non-destructively. Setting μs’ according to destructive photon density wave (PDW) spectroscopy and fitting μa resulted in root mean square error (rmse) of 18.7% in comparison to fitting μs’ resulting in rmse of 2.6%, pointing to decreased measuring uncertainty, when the highly variable μa was known. The approach was tested on European pear, utilizing destructive PDW spectroscopy for setting one variable, while LLBI was applied for calculating the remaining coefficient. Results indicated that the optical properties of pear obtained from PDW spectroscopy as well as LLBI changed concurrently in correspondence to water content mainly. A destructive batch-wise analysis of μs’ and online analysis of μa may be considered in future developments for improved fruit sorting results, when considering fruit with high variability of μs’. KW - Absorption KW - European pear KW - Fruit quality KW - Phantoms KW - Reduced scattering coefficient KW - Scattering KW - Spatially resolved spectroscopy Y1 - 2019 U6 - https://doi.org/10.1016/j.postharvbio.2019.04.002 SN - 0925-5214 SN - 1873-2356 VL - 153 SP - 161 EP - 168 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Haene, Janick A1 - Bruehwiler, Dominik A1 - Ecker, Achim A1 - Hass, Roland T1 - Real-time inline monitoring of zeolite synthesis by Photon Density Wave spectroscopy JF - Microporous and mesoporous materials : zeolites, clays, carbons and related materials N2 - The formation process of zeolite A (Linde Type A) was monitored inline at 1.5 L scale by Photon Density Wave (PDW) spectroscopy as novel process analytical technology for highly turbid liquid suspensions. As a result, the reduced scattering coefficient, being a measure for particle number, size, and morphology, provides distinct process information, including the formation of amorphous particles and their transfer into crystalline zeolite structures. The onset and end of the crystallization process can be detected inline and in real-time. Analyses by powder X-ray diffraction and electron microscopy, based on a sampling approach, support the interpretation of the results obtained by PDW spectroscopy. In addition, the influence of the molar water content was investigated, indicating a linear increase of the time needed to reach the end of the zeolite A crystallization with increasing molar water content. Further experiments indicate a strong influence of the silica source on the course of the crystallization. The applicability of PDW spectroscopy under even more demanding chemical and physical conditions was investigated by monitoring the synthesis of zeolite L (Linde Type L). KW - Photon density wave spectroscopy KW - Process analytical technology KW - Zeolite synthesis KW - Molar water content KW - Silica source Y1 - 2019 U6 - https://doi.org/10.1016/j.micromeso.2019.109580 SN - 1387-1811 SN - 1873-3093 VL - 288 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Bressel, Katharina A1 - Müller, Wenke A1 - Leser, Martin Erwin A1 - Reich, Oliver A1 - Hass, Roland A1 - Wooster, Tim J. T1 - Depletion-induced flocculation of concentrated emulsions probed by photon density wave spectroscopy JF - Langmuir N2 - Stable, creaming-free oil in water emulsions with high volume fractions of oil (phi = 0.05-0.40, density matched to water) and polysorbate 80 as an emulsifier were characterized without dilution by Photon Density Wave spectroscopy measuring light absorption and scattering behavior, the latter serving as the basis for droplet size distribution analysis. The emulsion with phi = 0.10 was used to investigate flocculation processes induced by xanthan as a semi-flexible linear nonabsorbing polymer. Different time regimes in the development of the reduced scattering coefficient mu(s)' could be identified. First, a rapid, temperature-dependent change in mu(s)' during the depletion process was observed. Second, the further decrease of mu(s)' follows a power law in analogy to a spinodal demixing behavior, as described by the Cahn-Hilliard theory. Y1 - 2020 U6 - https://doi.org/10.1021/acs.langmuir.9b03642 SN - 0743-7463 VL - 36 IS - 13 SP - 3504 EP - 3513 PB - American Chemical Society CY - Washington ER - TY - THES A1 - Hass, Roland T1 - Angewandte Photonendichtewellen Spektroskopie Y1 - 2011 CY - Potsdam ER - TY - JOUR A1 - Kutlug, Oezgür A1 - Hass, Roland A1 - Reck, Stephan A1 - Hartwig, Andreas T1 - Inline characterization of dispersion formation of a solvent-borne acrylic copolymer by Photon Density Wave spectroscopy JF - Colloids and surfaces : an international journal devoted to the principles and applications of colloid and interface science ; A, Physicochemical and engineering aspects N2 - Most investigations on phase inversion (PI) of resins upon addition of water have been carried out by dynamic light scattering (DLS), torque, and viscosity measurements. The main problem, however, is analytic discontinuity due to sample removal and a changing matrix due to dilution during the preparation of the aqueous resin dispersions. This work presents Photon Density Wave (PDW) spectroscopy as a tool for the inline characterization of the acetone process for an acrylic copolymer with high acrylic acid (AA) content. PDW spectroscopy revealed different trends for optical properties compared to torque during water feed. Also the absence of PI due to dissolution of copolymer in the solvent/water mixture is observed by PDW spectroscopy. PI for the investigated copolymer did not occour during water feed but during removal of solvent. Different feeding rates of water gave similar trends while a change in temperature and degree of AA neutralization led to changes in optical properties and torque. Thermal processing showed that the optical properties of mixtures prior and after removal of solvent were completely different caused by changes of solubility. KW - Acetone process KW - Dispersion KW - Photon Density Wave spectroscopy KW - Radical polymerization KW - Torque KW - Turbid media Y1 - 2018 U6 - https://doi.org/10.1016/j.colsurfa.2018.08.011 SN - 0927-7757 SN - 1873-4359 VL - 556 SP - 113 EP - 119 PB - Elsevier CY - Amsterdam ER - TY - GEN A1 - Werner, Peter A1 - Münzberg, Marvin A1 - Hass, Roland A1 - Reich, Oliver T1 - Process analytical approaches for the coil-to-globule transition of poly(N-isopropylacrylamide) in a concentrated aqueous suspension T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - The coil-to-globule transition of poly(N-isopropylacrylamide) (PNIPAM) microgel particles suspended in water has been investigated in situ as a function of heating and cooling rate with four optical process analytical technologies (PAT), sensitive to structural changes of the polymer. Photon Density Wave (PDW) spectroscopy, Focused Beam Reflectance Measurements (FBRM), turbidity measurements, and Particle Vision Microscope (PVM) measurements are found to be powerful tools for the monitoring of the temperature-dependent transition of such thermo-responsive polymers. These in-line technologies allow for monitoring of either the reduced scattering coefficient and the absorption coefficient, the chord length distribution, the reflected intensities, or the relative backscatter index via in-process imaging, respectively. Varying heating and cooling rates result in rate-dependent lower critical solution temperatures (LCST), with different impact of cooling and heating. Particularly, the data obtained by PDW spectroscopy can be used to estimate the thermodynamic transition temperature of PNIPAM for infinitesimal heating or cooling rates. In addition, an inverse hysteresis and a reversible building of micrometer-sized agglomerates are observed for the PNIPAM transition process. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 944 KW - poly(N-isopropylacrylamide) KW - Photon Density Wave spectroscopy KW - Focused Beam Reflectance Measurement KW - turbidity measurement KW - Particle Vision Microscope measurement KW - rate-dependent lower critical solution temperature Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-431162 SN - 1866-8372 IS - 944 SP - 807 EP - 819 ER - TY - JOUR A1 - Bressel, Lena A1 - Hass, Roland A1 - Reich, O. T1 - Particle sizing in highly turbid dispersions by Photon Density Wave spectroscopy JF - JOURNAL OF QUANTITATIVE SPECTROSCOPY & RADIATIVE TRANSFER N2 - Photon Density Wave (PDW) spectroscopy is presented as a fascinating technology for the independent determination of scattering (mu(s)’ and absorption (ita) properties of highly turbid liquid dispersions. The theory is reviewed introducing new expressions for the PDW coefficients k(I) and k(Phi). Furthermore, two models for dependent scattering, namely the hard sphere model in the Percus-Yevick Approximation (HSPYA) and the Yukawa model in the Mean Spherical Approximation (YMSA), are experimentally examined. On the basis of the HSPYA particle sizing is feasible in dispersions of high ionic strength. It is furthermore shown that in dialyzed dispersions or in technical copolymers with high particle charge only the YMSA allows for correct dilution-free particle sizing. (C) 2013 Elsevier Ltd. All rights reserved. KW - Photon Density Wave spectroscopy KW - Multiple light scattering KW - Dependent light scattering KW - Percus-Yevick model KW - Yukawa model KW - Particle sizing KW - Polymer dispersions Y1 - 2013 U6 - https://doi.org/10.1016/j.jqsrt.2012.11.031 SN - 0022-4073 VL - 126 IS - 1 SP - 122 EP - 129 PB - PERGAMON-ELSEVIER SCIENCE LTD CY - OXFORD ER - TY - JOUR A1 - Sandmann, Michael A1 - Münzberg, Marvin A1 - Bressel, Lena A1 - Reich, Oliver A1 - Hass, Roland T1 - Inline monitoring of high cell density cultivation of Scenedesmus rubescens in a mesh ultra-thin layer photobioreactor by photon density wave spectroscopy JF - BMC Research Notes / Biomed Central N2 - Objective Due to multiple light scattering that occurs inside and between cells, quantitative optical spectroscopy in turbid biological suspensions is still a major challenge. This includes also optical inline determination of biomass in bioprocessing. Photon Density Wave (PDW) spectroscopy, a technique based on multiple light scattering, enables the independent and absolute determination of optical key parameters of concentrated cell suspensions, which allow to determine biomass during cultivation. Results A unique reactor type, called "mesh ultra-thin layer photobioreactor" was used to create a highly concentrated algal suspension. PDW spectroscopy measurements were carried out continuously in the reactor without any need of sampling or sample preparation, over 3 weeks, and with 10-min time resolution. Conventional dry matter content and coulter counter measurements have been employed as established offline reference analysis. The PBR allowed peak cell dry weight (CDW) of 33.4 g L-1. It is shown that the reduced scattering coefficient determined by PDW spectroscopy is strongly correlated with the biomass concentration in suspension and is thus suitable for process understanding. The reactor in combination with the fiber-optical measurement approach will lead to a better process management. KW - Photon density wave spectroscopy KW - Multiple light scattering KW - Process KW - analytical technology KW - Fiber-optical spectroscopy KW - Mesh ultra-thin layer KW - photobioreactor Y1 - 2022 U6 - https://doi.org/10.1186/s13104-022-05943-2 SN - 1756-0500 VL - 15 IS - 1 PB - Biomed Central (London) CY - London ER - TY - JOUR A1 - Hass, Roland A1 - Münzberg, Marvin A1 - Bressel, Lena A1 - Reich, Oliver T1 - Industrial applications of photon density wave spectroscopy for in-line particle sizing [Invited] JF - Applied optics N2 - Optical spectroscopy in highly turbid liquid material is often restricted by simultaneous occurrence of absorption and scattering of light. Photon Density Wave (PDW) spectroscopy is one of the very few, yet widely unknown, technologies for the independent quantification of these two optical processes. Here, a concise overview about modern PDW spectroscopy is given, including all necessary equations concerning the optical description of the investigated material, dependent light scattering, particle sizing, and PDW spectroscopy itself. Additionally, it is shown how the ambiguity in particle sizing, arising from Mie theory, can be correctly solved. Due to its high temporal resolution, its applicability to highest particle concentrations, and its purely fiber-optical probe, PDW spectroscopy possesses all fundamental characteristics for optical in-line process analysis. Several application examples from the chemical industry are presented. (C) 2013 Optical Society of America Y1 - 2013 U6 - https://doi.org/10.1364/AO.52.001423 SN - 1559-128X SN - 2155-3165 VL - 52 IS - 7 SP - 1423 EP - 1431 PB - Optical Society of America CY - Washington ER - TY - JOUR A1 - Schlappa, Stephanie A1 - Brenker, Lee Josephine A1 - Bressel, Lena A1 - Hass, Roland A1 - Münzberg, Marvin T1 - Process characterization of polyvinyl acetate emulsions applying inline photon density wave spectroscopy at high solid contents JF - Polymers / Molecular Diversity Preservation International N2 - The high solids semicontinuous emulsion polymerization of polyvinyl acetate using poly (vinyl alcohol-co-vinyl acetate) as protective colloid is investigated by optical spectroscopy. The suitability of Photon Density Wave (PDW) spectroscopy as inline Process Analytical Technology (PAT) for emulsion polymerization processes at high solid contents (>40% (w/w)) is studied and evaluated. Inline data on absorption and scattering in the dispersion is obtained in real-time. The radical polymerization of vinyl acetate to polyvinyl acetate using ascorbic acid and sodium persulfate as redox initiator system and poly (vinyl alcohol-co-vinyl acetate) as protective colloid is investigated. Starved-feed radical emulsion polymerization yielded particle sizes in the nanometer size regime. PDW spectroscopy is used to monitor the progress of polymerization by studying the absorption and scattering properties during the synthesis of dispersions with increasing monomer amount and correspondingly decreasing feed rate of protective colloid. Results are compared to particle sizes determined with offline dynamic light scattering (DLS) and static light scattering (SLS) during the synthesis. KW - photon density wave spectroscopy KW - multiple light scattering KW - emulsion KW - polymerization KW - process analytical technology KW - polyvinyl acetate Y1 - 2021 U6 - https://doi.org/10.3390/polym13040669 SN - 2073-4360 VL - 13 IS - 4 PB - MDPI CY - Basel ER -