TY - THES A1 - Youk, Sol T1 - Molecular design of heteroatom-doped nanoporous carbons with controlled porosity and surface polarity for gas physisorption and energy storage N2 - The world energy consumption has constantly increased every year due to economic development and population growth. This inevitably caused vast amount of CO2 emission, and the CO2 concentration in the atmosphere keeps increasing with economic growth. To reduce CO2 emission, various methods have been developed but there are still many bottlenecks to be solved. Solvents easily absorbing CO2 such as monoethanol-amine (MEA) and diethanolamine, for example, have limitations of solvent loss, amine degradation, vulnerability to heat and toxicity, and the high cost of regeneration which is especially caused due to chemisorption process. Though some of these drawbacks can be compensated through physisorption with zeolites and metal-organic frameworks (MOFs) by displaying significant adsorption selectivity and capacity even in ambient conditions, limitations for these materials still exist. Zeolites demand relatively high regeneration energy and have limited adsorption kinetics due to the exceptionally narrow pore structure. MOFs have low stability against heat and moisture and high manufacturing cost. Nanoporous carbons have recently received attention as an attractive functional porous material due to their unique properties. These materials are crucial in many applications of modern science and industry such as water and air purification, catalysis, gas separation, and energy storage/conversion due to their high chemical and thermal stability, and in particular electronic conductivity in combination with high specific surface areas. Nanoporous carbons can be used to adsorb environmental pollutants or small gas molecules such as CO2 and to power electrochemical energy storage devices such as batteries and fuel cells. In all fields, their pore structure or electrical properties can be modified depending on their purposes. This thesis provides an in-depth look at novel nanoporous carbons from the synthetic and the application point of view. The interplay between pore structure, atomic construction, and the adsorption properties of nanoporous carbon materials are investigated. Novel nanoporous carbon materials are synthesized by using simple precursor molecules containing heteroatoms through a facile templating method. The affinity, and in turn the adsorption capacity, of carbon materials toward polar gas molecules (CO2 and H2O) is enhanced by the modification of their chemical construction. It is also shown that these properties are important in electrochemical energy storage, here especially for supercapacitors with aqueous electrolytes which are basically based on the physisorption of ions on carbon surfaces. This shows that nanoporous carbons can be a “functional” material with specific physical or chemical interactions with guest species just like zeolites and MOFs. The synthesis of sp2-conjugated materials with high heteroatom content from a mixture of citrazinic acid and melamine in which heteroatoms are already bonded in specific motives is illustrated. By controlling the removal procedure of the salt-template and the condensation temperature, the role of salts in the formation of porosity and as coordination sites for the stabilization of heteroatoms is proven. A high amount of nitrogen of up to 20 wt. %, oxygen contents of up to 19 wt.%, and a high CO2/N2 selectivity with maximum CO2 uptake at 273 K of 5.31 mmol g–1 are achieved. Besides, the further controlled thermal condensation of precursor molecules and advanced functional properties on applications of the synthesized porous carbons are described. The materials have different porosity and atomic construction exhibiting a high nitrogen content up to 25 wt. % as well as a high porosity with a specific surface area of more than 1800 m2 g−1, and a high performance in selective CO2 gas adsorption of 62.7. These pore structure as well as properties of surface affect to water adsorption with a remarkably high Qst of over 100 kJ mol−1 even higher than that of zeolites or CaCl2 well known as adsorbents. In addition to that, the pore structure of HAT-CN-derived carbon materials during condensation in vacuum is fundamentally understood which is essential to maximize the utilization of porous system in materials showing significant difference in their pore volume of 0.5 cm3 g−1 and 0.25 cm3 g−1 without and with vacuum, respectively. The molecular designs of heteroatom containing porous carbon derived from abundant and simple molecules are introduced in the presented thesis. Abundant precursors that already containing high amount of nitrogen or oxygen are beneficial to achieve enhanced interaction with adsorptives. The physical and chemical properties of these heteroatom-doped porous carbons are affected by mainly two parameters, that is, the porosity from the pore structure and the polarity from the atomic composition on the surface. In other words, controlling the porosity as well as the polarity of the carbon materials is studied to understand interactions with different guest species which is a fundamental knowledge for the utilization on various applications. N2 - Nanoporöse Kohlenstoffe haben in letzter Zeit aufgrund ihrer einzigartigen Eigenschaften als ein attraktives funktionelles poröses Material Aufmerksamkeit erregt. Diese Materialien sind aufgrund ihrer hohen chemischen und thermischen Stabilität und insbesondere aufgrund ihrer elektronischen Leitfähigkeit in Kombination mit hohen spezifischen Oberflächen von entscheidender Bedeutung für viele Anwendungen der modernen Wissenschaft und Industrie wie Wasser- und Luftreinigung, Katalyse, Gastrennung und Energiespeicherung/-umwandlung. Nanoporöse Kohlenstoffe können verwendet werden, um Umweltschadstoffe oder kleine Gasmoleküle wie CO2 zu adsorbieren und elektrochemische Energiespeicher wie Batterien und Brennstoffzellen anzutreiben. Ihre Porenstruktur oder ihre elektrischen Eigenschaften je nach Einsatzzweck modifiziert werden. Diese Arbeit bietet einen eingehenden Blick auf neuartige nanoporöse Kohlenstoffe aus synthetischer und anwendungstechnischer Sicht. Das Zusammenspiel zwischen Porenstruktur, atomarem Aufbau und den Adsorptionseigenschaften von nanoporösen Kohlenstoffmaterialien wird untersucht. Neuartige nanoporöse Kohlenstoffmaterialien werden unter Verwendung einfacher Vorläufermoleküle, die Heteroatome enthalten, durch ein einfaches Templatverfahren synthetisiert. Die Affinität und damit die Adsorptionskapazität von Kohlenstoffmaterialien gegenüber polaren Gasmolekülen (CO2 und H2O) wird durch die Modifikation ihres chemischen Aufbaus erhöht. Es wird auch gezeigt, dass diese Eigenschaften bei der elektrochemischen Energiespeicherung wichtig sind. Hier insbesondere für Superkondensatoren mit wässrigen Elektrolyten, die grundsätzlich auf der Physisorption von Ionen an Kohlenstoffoberflächen beruhen. Dies zeigt, dass nanoporöse Kohlenstoffe, genauso wie Zeolithen und MOFs, ein „funktionelles“ Material mit spezifischen physikalischen oder chemischen Wechselwirkungen mit Gastspezien sein können. Mit den Vorteilen einer hohen elektrischen Leitfähigkeit, einer gut entwickelten Porenstruktur und einer stark hydrophilen Oberflächenstruktur sind nanoporöse Kohlenstoffe vielversprechende Materialien, die weitreichende Auswirkungen auf verschiedene Bereiche des zukünftigen Energiebedarfs haben. KW - porous carbon KW - gas adsorption KW - energy storage KW - N-doped carbon KW - poröser Kohlenstoff KW - Gasadsorption KW - Energiespeicher KW - N-dotierter Kohlenstoff Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-539098 ER - TY - THES A1 - Sand, Patrick T1 - Übergangsmetallkatalysierte Funktionalisierungsreaktionen an Vinylsulfonylverbindungen T1 - Transition metal catalysed functionalisation of vinyl sulfonyl compounds N2 - Innerhalb dieser Arbeit erfolgte die erstmalige systematische Untersuchung von Vinylsulfonsäureethylester (1a), Phenylvinylsulfon (1b), N-Benzyl-N-methylethensulfonamid (1c) in der FUJIWARA-MORITANI Reaktion (alternativ als DHR bezeichnet). Bei dieser übergangsmetallkatalysierten Reaktion erfolgt der Aufbau einer neuen C-C-Bindung unter der doppelten Aktivierung einer C-H-Bindung. Somit kann ein atomökonomischer Aufbau von Molekülen realisiert werden, da keine Beiprodukte in Form von Salzen entstehen. Als aromatischer Reaktant wurden Acetanilide (2) verwendet, damit eine regiospezifische Kupplung durch die katalysatordirigierende Acetamid-Gruppe (CDG) erfolgt. Für die Pd-katalysierte DHR wurde eine umfangreiche Optimierung durchgeführt und anschließend konnten neun verschieden, substituierte 2 mit 1a und sieben verschieden, substituierte 2 mit 1b funktionalisiert werden. Da eine Reaktion mit 1c ausblieb, erfolgte ein Wechsel auf eine Ru-katalysierte Methode für die DHR. Mit dieser Methode konnte 1c mit Acetaniliden funktionalisiert werden und das Spektrum der verwendeten 2, in Form von deaktivierenden Substituenten erweitert werden. Im Anschluss wurden die sulfalkenylierten Acetanilide in weiterführenden Reaktionen untersucht. Hierfür wurde eine Reaktionssequenz bestehend aus einer DeacetylierungDiazotierung-Kupplungsreaktion verwendet, um die Acetamid-Gruppe in eine Abgangsgruppe zu überführen und danach in einer MATSUDA-HECK Reaktion zu kuppeln. Mit dieser Methode konnten mehrere 1,2-Dialkenylbenzole erhalten werden und die CDG ein weiteres Mal genutzt werden. Neben der Überführung der CDG in eine Abgangsgruppe konnte diese auch in die Synthese verschiedener Heterozyklen integriert werden. Dafür erfolgte zunächst eine 1,3-Zykloaddition durch deprotonierten Tosylmethylisocanid an der elektronenarmen Sulfalkenylgruppe zur Synthese von Pyrrolen. Anschließend erfolgte eine Kupplung der PyrrolFunktion und der CDG durch Zyklokondensation, wodurch Quinoline dargestellt wurden. Durch diese Synthesen konnten Schwefelanaloga des Naturstoffes Marinoquionolin A erhalten werden. Ein weitere übergangsmetallkatalysierte C-H-Aktivierungsreaktion, die MATSUDA-HECK Reaktion, wurde genutzt, um 1b zu mit verschieden, subtituierten Diazoniumsalzen zu arylieren. Hier konnten zahlreichen Styrenylsulfone erhalten werden. Der erfolgreiche Einsatz der Vinylsulfonylverbindungen in der Kreuzmetathese konnte innerhalb dieser Arbeit nicht erreicht werden. Daher erfolgte die Synthese verschiedener dialkenylierter Sulfonamide. Hierfür wurde die Kettenlänge der Alkenyl-Gruppe am Schwefel zwischen 2-3 und am Stickstoff zwischen 3-4 variiert. Der Einsatz der dialkenylierten Sulfonamide erfolgte in den zuvor untersuchten C-H-Aktivierungsmethoden. N-Allyl-N-phenylethensulfonamid (3) konnte erfolgreich in der DHR und HECK Reaktion funktionalisiert werden. Hierbei erfolgte eine methodenspezifische Kupplung in Abhängigkeit von der Elektronendichte der entsprechenden Alkenyl-Gruppe. Die DHR führte zur selektiven Arylierung der Vinyl-Gruppe und die HECK Reaktion zur Arylierung an der Allyl-Gruppe. Gemischte Produkte wurden nicht erhalten. Für die weiteren Diolefine wurde komplexe Produktgemische erhalten. Des Weiteren wurden die Diolefine in der Ringschlussmetathese untersucht und die entsprechenden Sultame in sehr guten Ausbeuten erhalten. Die Verwendung der Sultame in der C-H-Aktivierung war erfolglos. Es wird vermutet, dass für diese zweifachsubstituierten Sulfonamide die vorhandenen Reaktionsbedingungen optimiert werden müssen. Abschließend wurden verschiedene, enantiomerenreine Olefine ausgehend von Levoglucosenon dargestellt. Hierfür wurde Levoglucosenon zunächst mit einem Allyl- und 3-Butenylgrignard Reagenz umgesetzt. Die entsprechenden Produkte wurden in moderaten Ausbeuten erhalten. Eine weitere Methode begann mit der Reduktion von Levoglucosenon zum Levoglucosenol. Dieser Alkohol wurde mit Allylbromid erfolgreich verethert. Neben der Untersuchungen zur Ethersynthese, erfolgte die Veresterung von Levoglucosenol mit verschiedenen Sulfonylchloriden zu den entsprechenden Sulfonsäureestern. Diese Olefine wurden in einer Dominometathesereaktion untersucht. Ausgehend vom Allyllevoglucosenylether erfolgte die Darstellung eines Dihydrofurans. N2 - Within this work, the first systematic investigation of vinyl sulfonic acid ethyl ester (1a), phenyl vinyl sulfone (1b), N-benzyl-N-methylethene sulfonamide (1c) in the FUJIWARA-MORITANI reaction (alternatively referred to as DHR) was carried out. In this transition metal-catalysed reaction, the formation of a new C-C bond takes place through double activation of a C-H bond. Therefore, an atom-economical construction of molecules can be realised without the formation of by-products in the form of salts. Acetanilides (2) were used as aromatic reactants so that a regiospecific coupling by the catalyst-directing acetamide group (CDG) takes place. An extensive optimisation was carried out for the Pd catalysed DHR and subsequently nine differently substituted 2 could be functionalised with 1a and seven differently substituted 2 with 1b. Since a reaction with 1c failed to occur, a switch was made to a Ru-catalysed method for the DHR. With this method, 1c could be functionalised with acetanilides (2) and the spectrum of the acetanilides (2) used could be expanded to deactivating substituents. Subsequently, the sulfalkenylated acetanilides were investigated in further reactions. For this purpose, a reaction sequence consisting of a deacetylation-diazotisation-coupling reaction was used to convert the acetamide group into a leaving group and then to couple it in a MATSUDA-HECK reaction. With this method, several 1,2-dialkenylbenzenes could be obtained and the CDG was used one more time. In addition to transferring the CDG into a leaving group, it could also be integrated into the synthesis of various heterocycles. First, a 1,3 cycloaddition was carried out by deprotonated tosylmethylisocanide on the electron-deficient sulfalkenyl group for the synthesis of pyrroles. This was followed by coupling of the pyrrole function and the CDG by cyclocondensation, producing quinolines. Through these syntheses, sulfur analogues of the natural product marinoquionoline A could be obtained. Another transition metal-catalysed C-H activation reaction, the MATSUDA-HECK reaction, was used to arylate 1b with different subtituted aryldiazonium salts. Numerous styrenyl sulfones were obtained. Vinylsulfonyl compounds could not be used in cross-metathesis reactions within this work. Therefore, the synthesis of different dialkenylated sulfonamides was carried out. For this purpose, the chain length of the alkenyl group was varied between 2-3 at the sulfur atom and 3-4 at the nitrogen atom. The dialkenylated sulfonamides were used in the previously investigated C-H activation methods. N-allyl-N-phenylethensulfonamide (3) was successfully functionalised using the DHR and HECK reaction. Here, a method-specific coupling took place depending on the electron density of the corresponding alkenyl group. The DHR led to selective arylation at the vinyl group and the HECK reaction to selective arylation at the allyl group. Mixed products were not obtained. For the other diolefins, complex mixtures of products were obtained. Furthermore, the diolefins were investigated in ring closing metathesis reaction and the corresponding sultams were obtained in very good yields. The use of the synthesised sultams in C-H activation was unsuccessful. It is suggested that for these di-substituted sulfonamides the existing reaction conditions need to be optimised. Finally, various enantiomerically pure olefins were prepared starting from levoglucosenone. For this purpose, levoglucosenone was first reacted with an allyl-Grignard and 3 butenyl-Grignard reagent. The corresponding products were obtained in moderate yields. Another method started with the reduction of levoglucosenone to levoglucosenol. This alcohol was successfully etherified with allyl bromide. In addition to the studies on ether synthesis, the esterification of levoglucosenol with various sulfonyl chlorides to the corresponding sulfonic acid esters was carried out. These olefins were investigated in a domino metathesis reaction. Starting with allyl levoglucosenyl ether, the synthesis of a dihydrofuran was presented. KW - Vinylsulfonylverbindungen KW - Übergangsmetallkatalyse KW - vinyl sulfonyl compounds KW - transition metal catalysis Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-536879 ER - TY - THES A1 - Kossmann, Janina T1 - Controlled condensation to functional materials – synergetic effect of nitrogen content and pore structure T1 - Kontrollierte Kondensation zu funktionellen Materialien - Synergetische Wirkung von Stickstoffgehalt und Porenstruktur N2 - The development and optimization of carbonaceous materials is of great interest for several applications including gas sorption, electrochemical storage and conversion, or heterogeneous catalysis. In this thesis, the exploration and optimization of nitrogen containing carbonaceous materials by direct condensation of smart chosen, molecular precursors will be presented. As suggested with the concept of noble carbons, the choice of a stable, nitrogen-containing precursor will lead to an even more stable, nitrogen doped carbonaceous material with a controlled structure and electronic properties. Molecules fulfilling this requirement are for example nucleobases. The direct condensation of nucleobases leads to highly nitrogen containing carbonaceous materials without any further post or pretreatment. By using salt melt templating, pore structure adjustment is possible without the use of hazardous or toxic reagents and the template can be reused. Using these simple tools, the synergetic effect of the pore structure and nitrogen content of the materials can be explored. Within this thesis, the influence of the condensation parameters will be correlated to the structure and performance of the materials. First, the influence of the condensation temperature to the porosity and nitrogen content of guanine will be discussed and the exploration of highly CO2 selective structural pores in C1N1 materials will be shown. Further tuning the pore structure of the materials by salt melt templating will be then explored, the potential of the prepared materials as heterogeneous catalysts and their basic catalytic strength will be correlated to their nitrogen content and pore morphology. A similar approach is used to explore the water sorption behavior of uric acid derived carbonaceous materials as potential sorbents for heat transformation applications. Changes in maximum water uptake and hydrophilicity of the prepared materials will be correlated to the nitrogen content and pore architecture. Due to the high thermal stability, porosity, and nitrogen content of ionic liquid derived nitrogen doped carbonaceous materials, a simple impregnation and calcination route can be conducted to obtain copper nano cluster decorated nitrogen-doped carbonaceous materials. The activity as catalyst for the oxygen reduction reaction of the obtained materials will be shown and structure performance relations are discussed. In conclusion, the versatility of nitrogen doped carbonaceous materials with a nitrogen to carbon ratio of up to one will be shown. The possibility to tune the pore structure as well as the nitrogen content by using a simple procedure including salt melt templating as well as the use of molecular precursors and their effect on the performance will be discussed. N2 - Die Entwicklung und Optimierung von kohlenstoffhaltigen Materialien ist von großem Interesse in vielen Anwendungsbereichen, darunter Gassorption, elektrochemische Speicherung und Umwandlung von Energie und in der heterogenen Katalyse. In dieser Arbeit wird die Erforschung und Optimierung von stickstoff‑ und kohlenstoffhaltigen Materialien durch direkte Kondensation ausgewählter, molekularer Ausgangsstoffe vorgestellt. Entsprechend dem Konzept der edlen Kohlenstoffe (noble carbons), führt die Kondensation eines stabilen, stickstoffhaltigen Ausgangsstoffes zu einem noch stabileren, stickstoffdotierten kohlenstoffhaltigen Material mit kontrollierter Struktur und elektronischen Eigenschaften. Moleküle, die diese Anforderung erfüllen, sind zum Beispiel Nukleobasen. Die direkte Kondensation von Nukleobasen führt ohne weitere Nach- oder Vorbehandlungen zu kohlenstoffhaltigen Materialien mit einem sehr hohen Stickstoffanteil. Durch die Verwendung des Salzschmelze-Template Verfahrens ist eine Anpassung der Porenstruktur ohne Verwendung gefährlicher oder toxischer Reagenzien möglich und die Templates können außerdem wiederverwendet werden. Mit diesen einfachen Werkzeugen kann der synergetische Effekt der Porenstruktur und des Stickstoffgehalts der Materialien erforscht werden. Im Rahmen dieser Arbeit wird der Einfluss der Kondensationsparameter auf die Struktur und die Leistung der Materialien in Beziehung gesetzt. Zunächst wird der Einfluss der Kondensationstemperatur auf die Porosität und den Stickstoffgehalt von Guanin erörtert und die Erforschung von CO2-selektiven strukturellen Poren in C1N1-Materialien aufgezeigt. Das Potenzial der hergestellten Materialien als heterogener Katalysator und ihre katalytische Wirkung werden mit ihrem Stickstoffgehalt und ihrer Porenstruktur korreliert. Ein ähnlicher Ansatz wird verwendet, um das Wassersorptionsverhalten von aus Harnsäure hergestellten kohlenstoffhaltigen Materialien als potenzielle Sorptionsmittel für Wärmetransformationsanwendungen zu untersuchen. Die maximale Wasseraufnahme und Hydrophilie der hergestellten Materialien werden mit dem Stickstoffgehalt und der Porenarchitektur korreliert. Aufgrund der hohen thermischen Stabilität, der Porosität und des Stickstoffgehalts der mit ionischer Flüssigkeit hergestellten stickstoffdotierten kohlenstoffhaltigen Materialien können diese des Weiteren als Träger für Metalle dienen. Durch einfache Imprägnierung und Kalzinierung werden Kupfer‑Nanocluster dekorierte stickstoffhaltige Kohlenstoffmaterialen hergestellt und als Katalysator für die in Brennstoffzellen stattfindende Sauerstoff-Reduktionsreaktion genutzt. Zusammenfassend wird die Vielseitigkeit von stickstoffdotierten kohlenstoffhaltigen Materialien mit einem Stickstoff-Kohlenstoff-Verhältnis von bis zu eins aufgezeigt. Es wird die Möglichkeit gezeigt, die Porenstruktur und den Stickstoffgehalt in einem einfachen Verfahren, einschließlich Salzschmelze‑Templating und die Verwendung von molekularen Ausgangsstoffen, zu beeinflussen und somit für gezielte Anwendungen zu variieren. KW - CO2 capture KW - nitrogen containing carbonaceous materials KW - C1N1 KW - heat transformation application KW - oxygen reduction reaction KW - salt melt templating KW - C1N1 KW - CO2-Abscheidung KW - Wärmetransformationsanwendungen KW - Stickstoff‑ und Kohlenstoffhaltige Materialien KW - Sauerstoff-Reduktionsreaktion KW - Salzschmelze-Templating Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-536935 ER - TY - THES A1 - Brandi, Francesco T1 - Integrated biorefinery in continuous flow systems using sustainable heterogeneous catalysts T1 - Integrierte Bioraffinerie in kontinuierlichen Fließsystemen unter Verwendung nachhaltiger heterogener Katalysatoren N2 - The negative impact of crude oil on the environment has led to a necessary transition toward alternative, renewable, and sustainable resources. In this regard, lignocellulosic biomass (LCB) is a promising renewable and sustainable alternative to crude oil for the production of fine chemicals and fuels in a so-called biorefinery process. LCB is composed of polysaccharides (cellulose and hemicellulose), as well as aromatics (lignin). The development of a sustainable and economically advantageous biorefinery depends on the complete and efficient valorization of all components. Therefore, in the new generation of biorefinery, the so-called biorefinery of type III, the LCB feedstocks are selectively deconstructed and catalytically transformed into platform chemicals. For this purpose, the development of highly stable and efficient catalysts is crucial for progress toward viability in biorefinery. Furthermore, a modern and integrated biorefinery relies on process and reactor design, toward more efficient and cost-effective methodologies that minimize waste. In this context, the usage of continuous flow systems has the potential to provide safe, sustainable, and innovative transformations with simple process integration and scalability for biorefinery schemes. This thesis addresses three main challenges for future biorefinery: catalyst synthesis, waste feedstock valorization, and usage of continuous flow technology. Firstly, a cheap, scalable, and sustainable approach is presented for the synthesis of an efficient and stable 35 wt.-% Ni catalyst on highly porous nitrogen-doped carbon support (35Ni/NDC) in pellet shape. Initially, the performance of this catalyst was evaluated for the aqueous phase hydrogenation of LCB-derived compounds such as glucose, xylose, and vanillin in continuous flow systems. The 35Ni/NDC catalyst exhibited high catalytic performances in three tested hydrogenation reactions, i.e., sorbitol, xylitol, and 2-methoxy-4-methylphenol with yields of 82 mol%, 62 mol%, and 100 mol% respectively. In addition, the 35Ni/NDC catalyst exhibited remarkable stability over a long time on stream in continuous flow (40 h). Furthermore, the 35Ni/NDC catalyst was combined with commercially available Beta zeolite in a dual–column integrated process for isosorbide production from glucose (yield 83 mol%). Finally, 35Ni/NDC was applied for the valorization of industrial waste products, namely sodium lignosulfonate (LS) and beech wood sawdust (BWS) in continuous flow systems. The LS depolymerization was conducted combining solvothermal fragmentation of water/alcohol mixtures (i.e.,methanol/water and ethanol/water) with catalytic hydrogenolysis/hydrogenation (SHF). The depolymerization was found to occur thermally in absence of catalyst with a tunable molecular weight according to temperature. Furthermore, the SHF generated an optimized cumulative yield of lignin-derived phenolic monomers of 42 mg gLS-1. Similarly, a solvothermal and reductive catalytic fragmentation (SF-RCF) of BWS was conducted using MeOH and MeTHF as a solvent. In this case, the optimized total lignin-derived phenolic monomers yield was found of 247 mg gKL-1. N2 - Die negativen Auswirkungen von Rohöl auf die Umwelt haben zu einem notwendigen Übergang zu alternativen, erneuerbaren und nachhaltigen Ressourcen geführt. In dieser Hinsicht ist lignozellulosehaltige Biomasse (LCB) eine vielversprechende erneuerbare und nachhaltige Alternative zu Erdöl für die Herstellung von Feinchemikalien und Kraftstoffen in einem sogenannten Bioraffinerie-Prozess. LCB setzt sich aus Polysacchariden (Cellulose und Hemicellulose) sowie Aromaten (Lignin) zusammen. Die Entwicklung einer nachhaltigen und wirtschaftlich vorteilhaften Bioraffinerie hängt von der vollständigen und effizienten Verwertung aller Komponenten ab. Zu diesem Zweck ist die Entwicklung hochstabiler und effizienter Katalysatoren entscheidend für den Fortschritt in Richtung Bioraffinerie-Wirtschaftlichkeit. Darüber hinaus ist eine moderne und integrierte Bioraffinerie auf ein Prozess- und Reaktordesign angewiesen, das auf effizientere und kostengünstigere Methoden abzielt, die den Abfall minimieren. In diesem Zusammenhang hat die Verwendung von kontinuierlichen Durchflusssystemen das Potenzial, sichere, nachhaltige und innovative Transformationen mit einfacher Prozessintegration und Skalierbarkeit für Bioraffineriesysteme zu bieten. Diese Arbeit befasst sich mit drei wesentlichen Herausforderungen für die zukünftige Bioraffinerie: Katalysatorsynthese, Valorisierung von Abfallstoffen und Einsatz von kontinuierlicher Durchflusstechnik. Zuerst wird ein kostengünstiger, skalierbarer und nachhaltiger Ansatz für die Synthese eines effizienten und stabilen 35-Gew.-%-Ni-Katalysators auf einem hochporösen, stickstoffdotierten Kohlenstoffträger (35Ni/NDC) in Pelletform vorgestellt. Zunächst wurde die Leistung dieses Katalysators für die Hydrierung von LCB-abgeleiteten Verbindungen wie Glucose, Xylose und Vanillin in kontinuierlichen Durchflusssystemen in wässriger Phase bewertet. Der 35Ni/NDC-Katalysator zeigte hohe katalytische Leistungen in drei getesteten Hydrierungsreaktionen, d. h. Sorbit, Xylit und 2-Methoxy-4-methylphenol mit Ausbeuten von 82 mol%, 62 mol% bzw. 100 mol%. Darüber hinaus zeigte der 35Ni/NDC-Katalysator eine bemerkenswerte Stabilität über eine lange Zeit im kontinuierlichen Fluss (40 h). Auβerrdem wurde der 35Ni/NDC-Katalysator mit handelsüblichem Beta-Zeolith in einem integrierten Zweisäulenprozess für die Isosorbid-Produktion aus Glukose kombiniert (Ausbeute 83 mol%). Schließlich wurde 35Ni/NDC für die Valorisierung von industriellen Abfallprodukten, nämlich Natriumlignosulfonat (LS) und Buchenholzsägemehl (BWS) in kontinuierlichen Durchflusssystemen eingesetzt. Die Depolymerisation von LS wurde durch eine Kombination von solvothermischer Fragmentierung von Wasser/Alkohol-Gemischen (d.h. MeOH/Wasser und Ethanol/Wasser) mit katalytischer Hydrogenolyse/Hydrierung (SHF) durchgeführt. Es wurde festgestellt, dass die Depolymerisation thermisch in Abwesenheit des Katalysators mit einem abstimmbaren Molekulargewicht in Abhängigkeit von der Temperatur erfolgt. Außerdem wurde mit der SHF eine optimierte kumulative Monomerausbeute von 42 mg gLS-1 erzielt. In ähnlicher Weise wurde eine solvothermale und reduktiv-katalytische Fragmentierung (SF-RCF) von BWS mit MeOH und MeTHF als Lösungsmittel durchgeführt. In diesem Fall wurde eine optimierte Gesamtmonomerausbeute von 247 mg gKL-1 gefunden. KW - sustainable chemistry KW - green chemistry KW - biorefinery KW - flow chemistry KW - heterogeneous catalysis KW - Bioraffinerie KW - grüne Chemie KW - heterogene Katalyse KW - Strömungschemie KW - nachhaltige Chemie Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-537660 ER - TY - THES A1 - Haubitz, Toni T1 - Transient absorption spectroscopy T1 - Transienten Absorptionsspektroskopie BT - a versatile tool for investigating excited states in organic and inorganic molecules BT - ein vielseitiges Werkzeug zur Untersuchung angeregter Zustände von organischen und anorganischen Molekülen N2 - The optical properties of chromophores, especially organic dyes and optically active inorganic molecules, are determined by their chemical structures, surrounding media, and excited state behaviors. The classical optical go-to techniques for spectroscopic investigations are absorption and luminescence spectroscopy. While both techniques are powerful and easy to apply spectroscopic methods, the limited time resolution of luminescence spectroscopy and its reliance on luminescent properties can make its application, in certain cases, complex, or even impossible. This can be the case when the investigated molecules do not luminesce anymore due to quenching effects, or when they were never luminescent in the first place. In those cases, transient absorption spectroscopy is an excellent and much more sophisticated technique to investigate such systems. This pump-probe laser-spectroscopic method is excellent for mechanistic investigations of luminescence quenching phenomena and photoreactions. This is due to its extremely high time resolution in the femto- and picosecond ranges, where many intermediate or transient species of a reaction can be identified and their kinetic evolution can be observed. Furthermore, it does not rely on the samples being luminescent, due to the active sample probing after excitation. In this work it is shown, that with transient absorption spectroscopy it was possible to identify the luminescence quenching mechanisms and thus luminescence quantum yield losses of the organic dye classes O4-DBD, S4-DBD, and pyridylanthracenes. Hence, the population of their triplet states could be identified as the competitive mechanism to their luminescence. While the good luminophores O4-DBD showed minor losses, the S4-DBD dye luminescence was almost entirely quenched by this process. However, for pyridylanthracenes, this phenomenon is present in both the protonated and unprotonated forms and moderately effects the luminescence quantum yield. Also, the majority of the quenching losses in the protonated forms are caused by additional non-radiative processes introduced by the protonation of the pyridyl rings. Furthermore, transient absorption spectroscopy can be applied to investigate the quenching mechanisms of uranyl(VI) luminescence by chloride and bromide. The reduction of the halides by excited uranyl(VI) leads to the formation of dihalide radicals X^(·−2). This excited state redox process is thus identified as the quenching mechanism for both halides, and this process, being diffusion-limited, can be suppressed by cryogenically freezing the samples or by observing these interactions in media with a lower dielectric constant, such as ACN and acetone. N2 - Die optischen Eigenschaften von organischen Farbstoffen und optisch aktiven anorganischen Molekülen werden durch ihre chemische Struktur, ihrer chemischer Umgebung, und durch das Verhalten ihrer angeregten Zustände bestimmt. Die klassischen Methoden zur Untersuchung dieser Eigenschaften sind die Absorptions- und Lumineszenzspektroskopie. Obwohl beide Methoden leistungsfähig und einfach anzuwenden sind, stellen die fehlende Zeitauflösung respektive das benötigte Vorhandensein von Lumineszenz in gewissen Anwendungen ein Problem dar. Dies ist der Fall, wenn die zu untersuchenden Moleküle durch Löscheffekte keine Lumineszenz mehr aufweisen oder von vornherein nicht lumineszent sind. Unter diesen Umständen ist die Transientenabsorptionsspektroskopie eine exzellente Alternative. Dieses laserspektroskopische Anregungs-Abfrage-Verfahren ist für mechanistische Untersuchungen von Lumineszenz-Löschphänomenen und Photoreaktionen sehr gut geeignet. Aufgrund seiner extrem hohen Zeitauflösung im Femto- und Picosekundenbereich können Intermediate und transiente Spezies identifiziert und deren kinetische Entwicklung beobachtet werden. Da es sich außerdem eine aktive Abfrage des Probenzustands handelt, entfällt die Notwendigkeit von lumineszenten Probeneigenschaften. In dieser Arbeit konnten mittels Transientenabsorptionsspektroskopie die Lumineszenz-Löschmechanismen der organischen Farbstoffklassen O4-DBD, S4-DBD, und der Pyridylanthracene aufgeklärt werden. Bei all diesen Farbstoffen konnte die Bildung von Triplettzuständen als kompetitiver Mechanismus zur Lumineszenz identifiziert werden. Während bei den O4-DBD-Farbstoffen diese Verluste eher gering ausfallen, wird die Lumineszenz der S4-DBD-Farbstoffe fast vollständig gelöscht. Eine Triplettbildung konnte ebenfalls bei den Pyridylanthracenen beobachtet werden, sie hat jedoch einen eher moderaten Anteil am Löschverhalten der Lumineszenz. Der Hauptteil der Lumineszenz-Löschung der protonierten Pyridylanthracene wird eher durch zusätzliche nicht-strahlende Desaktivierungsprozesse über die Pyridylringe verursacht. Es konnte gezeigt werden, dass die Transientenabsorptionsspektroskopie für die Untersuchung des Löschverhaltens von Uranyl(VI)-Lumineszenz durch Chlorid und Bromid geeignet ist. Es wurde geschlussfolgert, dass die Reduktion der Halogenide durch angeregtes Uranyl(VI) zur Bildung von Dihalogenidradikalen X^(·−2). führt. Diese Redoxreaktion im angeregten Zustand wurde daher als Lumineszenz-Löschmechanismus für beide Halogenide identifiziert. Dieser diffusionslimitierte Mechanismus wird unter cryogenen Bedingungen oder in schwächeren dielektriktrischen Lösemitteln wie ACN oder Aceton unterdrückt. KW - spectroscopy KW - luminescence KW - dye KW - quenching KW - uranyl KW - DBD KW - transient KW - Spektroskopie KW - Lumineszenz KW - Farbstoff KW - Löschung KW - Uranyl KW - DBD KW - Transient Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-535092 ER - TY - THES A1 - Kluge, Steven T1 - Integration anorganischer Füllstoffe in Polysulfonmembranen und Auswirkungen auf die Gastransporteigenschaften T1 - Integration of inorganic fillers in polysulfone membranes and effects on the gas transport properties N2 - In der vorliegenden Arbeit wird die Herstellung und Charakterisierung von Mixed-Matrix-Membranen (MMM) für die Gastrennung thematisiert. Dazu wurden verschiedene Füllstoffe genutzt, um in Verbindung mit dem Membranmaterial Polysulfon MMMs herzustellen. Als Füllstoffe wurden 3 aktive und 2 passive Füllstoffe verwendet. Die aktiven Füllstoffe besaßen Porenöffnungen, die in der Lage sind Gase in Abhängigkeit der Molekülgröße zu trennen. Daraus folgt ein höherer idealer Trennfaktor für bestimmte Gaspaare als in Polysulfon selbst. Aufgrund der durch die Poren gebildeten permanenten Kanäle in den aktiven Füllstoffen ergibt sich ein schnellerer Gastransport (Permeabilität) als in Polysulfon. Es handelte sich bei den aktiven Füllstoffen um den Zeolith SAPO-34 und 2 Chargen eines Zeolitic Imidazolate Framework (ZIF) ZIF-8. Die beiden Chargen ZIF-8 unterschieden sich in ihrer spezifischen Oberfläche, was diesen Einfluss speziell in die Untersuchungen zum Gastransport einbeziehen sollte. Bei den passiven Füllstoffen handelte es sich um ein aminofunktionalisiertes Kieselgel und unporöse (dichte) Glaskügelchen. Das Kieselgel besaß Poren, die zu groß waren, um Gase effektiv zu trennen. Die Glaskügelchen konnten keine Gastrennung ermöglichen, da sie keine Poren besaßen. Aus der Literatur ist bekannt, dass die Einbettung von Füllstoffen oft zu Defekten in MMMs führt. Ein Ziel dieser Arbeit war es daher die Einbettung zu optimieren. Weiterhin sollte der Gastransport in MMMs dieser Arbeit mit dem in einer unbeladenen Polysulfonmembran verglichen werden. Aufgrund des selektiveren Trennverhaltens der aktiven Füllstoffe im Vergleich zum Membranmaterial, sollte mit der Einbettung aktiver Füllstoffe die Trennleistung der MMMs mit steigender Füllstoffbeladung immer weiter verbessert werden. Um die Eigenschaften der MMMs zu untersuchen, wurden diese mittels Rasterelektronenmikroskop (REM), Gaspermeationsmessungen (GP) und Thermogravimetrischer Analyse gekoppelt mit Massenspektrometrie (TGA-MS) charakterisiert. Untersuchungen am REM konnten eine Verbesserung der Einbettung zeigen, wenn ein polymerer Haftvermittler verwendet wurde. Verglichen wurde die optimierte Einbettung mit der Einbettung ohne Haftvermittler und Ergebnissen aus der Literatur, in der die Verwendung verschiedener Silane als Haftvermittler beschrieben wurde. Trotz der verbesserten Einbettung konnte lediglich bei geringen Beladungen an Füllstoff (10 und 20 Ma-% bezogen auf das Membranmaterial) eine geringe Steigerung des idealen Trennfaktors in den MMMs gegenüber der unbeladenen Polysulfonmembranen beobachtet werden. Bei höheren Füllstoffbeladungen (30, 40 und 50 Ma-%) war ein deutlicher Anstieg der Permeabilität bei stark sinkendem idealen Trennfaktor zu beobachten. Mit Hilfe von TGA-MS Messungen konnte darüber hinaus festgestellt werden, dass der verwendete Zeolith SAPO-34 durch Wassermoleküle blockierte Porenöffnungen besaß. Das verhinderte den Gastransport im Füllstoff, wodurch die Trennleistung des Füllstoffes nicht ausgenutzt werden konnte. Die Füllstoffe ZIF-8 (chargenunabhängig) und aminofunktionalisiertes Kieselgel wiesen keine blockierten Poren auf. Dennoch zeigte sich in diesen MMMs keine Verbesserung der Gastrenn- oder Gastransporteigenschaften. MMMs mit dichten Glaskügelchen als Füllstoff zeigten dasselbe Gastrenn- und Gastransportverhalten, wie alle MMMs mit den zuvor genannten Füllstoffen. In dieser Arbeit konnte, trotz optimierter Einbettung anorganischer Füllstoffe, für MMMs keine Verbesserung der Gastrenn- oder Gastransporteigenschaften nachgewiesen werden. Vielmehr wurde ein Einfluss der Füllstoffmenge auf die Gastransporteigenschaften in MMMs festgestellt. Die Änderungen der MMMs gegenüber Polysulfon stammen von den Folgen der Einbettung von Füllstoffen in das Matrixpolymer. Durch die Einbettung werden die Eigenschaften des Matrixpolymers ändern, sodass auch der Gastransport beeinflusst wird. Des Weiteren wurde dokumentiert, dass in Abhängigkeit der Füllstoffbeladung die entstehende Membranstruktur beeinflusst wird. Die Beeinflussung war dabei unabhängig von der Füllstoffart. Es wurde eine Korrelation zwischen Füllstoffmenge und veränderter Membranstruktur gefunden. N2 - The present work deals with the production and characterization of mixed matrix membranes (MMM) for gas separation. Various fillers were used to fabricate MMMs in combination with polysulfone as a membrane material. Three active and two passive fillers were used. Active fillers have pore openings that are able to separate gases depending on the size of the molecule. This results in a higher ideal selectivity for certain gas pairs as Polysulfone can reach. Due to the permanent channels formed by pores in the active fillers, there is also a faster gas transport (permeability) than in the membrane material polysulfone. The active fillers were the zeolite SAPO-34 and two batches of a zeolitic imidazolate framework (ZIF) ZIF-8. The two batches ZIF 8 differed in their specific surface area, which should include this influence especially in the investigations on gas transport. Passive fillers were an amino-functionalized silica and non-porous (dense) glass beads. Silica had pores that are too large to effectively separate gases. The glass beads could not enable gas separation because they did not have pores. It is known from literature that embedding of fillers often leads to defects in MMMs. One of the aims of this work was therefore to optimize the embedding of fillers. Furthermore, the gas transport of MMMs was compared with that in a polysulfone membrane without fillers. Due to the more selective separation behavior of the active fillers compared to the membrane material, the embedding of active fillers should improve the separation performance of the MMMs with increasing filler loading. In order to investigate the properties, MMMs were characterized using a scanning electron microscope (SEM), gas permeation measurements (GP) and thermogravimetric analysis coupled with mass spectrometry (TGA-MS). Investigations with SEM were able to show an improvement of embedding of fillers when a polymeric adhesion promoter was used. The optimized embedding was compared with the embedding without adhesion promoter and results from literature in which the use of various silanes as adhesion promoters was described. Despite the improved embedding, a slight increase in ideal selectivity in the MMMs compared to the polysulfone membranes without fillers could only be observed at low loadings of fillers (10 and 20 Ma-%, based on the membrane material). At higher filler loadings (30, 40 and 50 Ma-%), a clear increase in permeability was observed with a sharp decrease in the ideal selectivity. With the aid of TGA-MS measurements, it was possible to determine that the zeolite SAPO-34 had pore openings blocked by water molecules. This prevented the gas transport in the filler, so that the separating capacity of the filler could not be used. ZIF 8 (batch-independent) and amino-functionalized silica did not show any blocked pores. Nevertheless, there was no improvement in gas separation or gas transport properties in MMMs. MMMs with dense glass beads as filler showed the same gas separation and gas transport behavior as all MMMs with the aforementioned fillers. In this work, despite the optimized embedding of inorganic fillers for MMMs, no improvement in gas separation or gas transport properties could be demonstrated. Rather, an influence of the amount of filler on the gas transport properties in MMMs was found. The changes in MMMs compared to polysulfone stem from the consequences of embedding fillers in the matrix polymer. The embedding changes the properties of the matrix polymer, so that the gas transport is also influenced. The influence was independent of the type of filler. Furthermore, it was documented that depending on the filler load, the resulting membrane structure is influenced. A correlation between the amount of filler and the altered membrane structure was found. KW - Dissertation KW - Polysulfon KW - Membran KW - Gastrennung KW - Mixed-Matrix-Membran KW - dissertation KW - membrane KW - mixed-matrix-membrane KW - polysulfone Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-532700 ER - TY - THES A1 - Chandrakanth Shetty, Sunidhi T1 - Directed chemical communication in artificial eukaryotic cells T1 - Gezielte chemische Kommunikation in künstlichen eukaryotischen Zellen N2 - Eukaryotic cells can be regarded as complex microreactors capable of performing various biochemical reactions in parallel which are necessary to sustain life. An essential prerequisite for these complex metabolic reactions to occur is the evolution of lipid membrane-bound organelles enabling compartmental- ization of reactions and biomolecules. This allows for a spatiotemporal control over the metabolic reactions within the cellular system. Intracellular organi- zation arising due to compartmentalization is a key feature of all living cells and has inspired synthetic biologists to engineer such systems with bottom-up approaches. Artificial cells provide an ideal platform to isolate and study specific re- actions without the interference from the complex network of biomolecules present in biological cells. To mimic the hierarchical architecture of eukaryotic cells, multi-compartment assemblies with nested liposomal structures also re- ferred to as multi-vesicular vesicles (MVVs) have been widely adopted. Most of the previously reported multi-compartment systems adopt bulk method- ologies which suffer from low yield and poor control over size. Microfluidic strategies help circumvent these issues and facilitate a high-throughput and robust technique to assemble MVVs of uniform size distribution. In this thesis, firstly, the bulk methodologies are explored to build MVVs and implement a synthetic signalling cascade. Next, a polydimethylsiloxane (PDMS)-based microfluidic platform is introduced to build MVVs and the significance of PEGylated lipids for the successful encapsulation of inner com- partments to generate stable multi-compartment systems is highlighted. Next, a novel two-inlet channel PDMS-based microfluidic device to create MVVs encompassing a three-step enzymatic reaction cascade is presented. A directed reaction pathway comprising of the enzymes α-glucosidase (α-Glc), glucose oxidase (GOx), and horseradish peroxidase (HRP) spanning across three compartments via reconstitution of size-selective membrane proteins is described. Furthermore, owing to the monodispersity of our MVVs due to microfluidic strategies, this platform is employed to study the effect of com- partmentalization on reaction kinetics. Further integration of cell-free expression module into the MVVs would allow for gene-mediated signal transduction within artificial eukaryotic cells. Therefore, the chemically inducible cell-free expression of a membrane protein alpha-hemolysin and its further reconstitution into liposomes is carried out. In conclusion, the present thesis aims to build artificial eukaryotic cells to achieve size-selective chemical communication that also show potential for applications as micro reactors and as vehicles for drug delivery. N2 - Eukaryontische Zellen können als komplexe Mikroreaktoren betrachtet werden, die in der Lage sind, verschiedene biochemische Reaktionen parallel durchzuführen, die für die Aufrechterhaltung des Lebens notwendig sind. Eine wesentliche Voraussetzung für die Durchführung dieser komplexen Stoffwechselreaktionen ist die Entwicklung von Organellen mit Lipidmembranen, die eine Kompartimentierung von Reaktionen und Biomolekülen ermöglichen. Dies ermöglicht eine räumlich-zeitliche Kontrolle über die Stoffwechselreaktionen innerhalb des zellulären Systems. Die durch die Kompartimentierung entstehende intrazelluläre Organisation ist ein Schlüsselmerkmal aller lebenden Zellen und hat synthetische Biologen dazu inspiriert, solche Systeme mit Bottom-up-Ansätzen zu entwickeln. Künstliche Zellen bieten eine ideale Plattform, um spezifische Reaktionen zu isolieren und zu untersuchen, ohne dass das komplexe Netzwerk von Biomolekülen, das in biologischen Zellen vorhanden ist, stört. Um die hierarchische Architektur eukaryontischer Zellen zu imitieren, haben sich Multikompartiment-Anordnungen mit verschachtelten liposomalen Strukturen, die auch als multivesikuläre Vesikel (MVV) bezeichnet werden, durchgesetzt. Die meisten der bisher vorgestellten Multikompartiment-Systeme basieren auf Bulk-Methoden, die eine geringe Ausbeute und eine schlechte Kontrolle über die Größe aufweisen. Mikrofluidische Strategien helfen, diese Probleme zu umgehen und ermöglichen eine robuste Technik mit hohem Durchsatz, um MVVs mit einheitlicher Größenverteilung herzustellen. In dieser Dissertation werden zunächst die Bulk-Methoden zum Aufbau von MVVs und zur Implementierung einer synthetischen Signalkaskade untersucht. Anschließend wird eine auf Polydimethylsiloxan (PDMS) basierende mikrofluidische Plattform zur Herstellung von MVVs vorgestellt und die Bedeutung von PEGylierten Lipiden für die erfolgreiche Verkapselung der inneren Kompartimente zur Erzeugung stabiler Multikompartiment-Systeme hervorgehoben. Es wird ein neuartiges mikrofluidisches Gerät mit zwei Einlasskanälen auf PDMS-Basis zur Herstellung von MVVs vorgestellt, das eine dreistufige enzymatische Reaktionskaskade umfasst. Es wird ein gerichteter Reaktionsweg beschrieben, der die Enzyme α-Glucosidase (α-Glc), Glucoseoxidase (GOx) und Meerrettichperoxidase (HRP) umfasst und sich über drei Kompartimente erstreckt, die durch die Rekonstitution von größenselektiven Membranproteinen entstehen. Aufgrund der Monodispersität unserer MVVs durch mikrofluidische Strategien nutze ich diese Plattform außerdem, um die Auswirkungen der Kompartimentierung auf die Reaktionskinetik zu untersuchen. Eine weitere Integration von zellfreien Expressionsmodulen in MVVs würde eine genvermittelte Signaltransduktion in künstlichen eukaryotischen Zellen ermöglichen. Daher wird die chemisch induzierbare zellfreie Expression eines Membranproteins alpha-Hämolysin und seine weitere Rekonstitution in Liposomen durchgeführt. Zusammenfassend lässt sich sagen, dass die vorliegende Arbeit darauf abzielt, künstliche eukaryotische Zellen zu bauen, um eine größenselektive chemische Kommunikation zu erreichen, und das Potenzial für Anwendungen als Mikroreaktoren und als Vehikel für die Verabreichung von Medikamenten aufweisen. KW - microfluidics KW - synthetic biology KW - Mikrofluidik KW - synthetische Biologie Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-533642 ER - TY - THES A1 - Bagdahn, Christian T1 - Synthese und Charakterisierung von Polymerionogelen basierend auf ionischen Flüssigkeiten und Polymethylmethacrylat N2 - Zentrales Element dieser Arbeit ist die Synthese und Charakterisierung praktisch nutzbarer Ionogele. Die Basis der Polymerionogele bildet das Modellpolymer Polymethylmethacrylat. Als Additive kommen ionische Flüssigkeiten zum Einsatz, deren Grundlage Derivate des vielfach verwendeten Imidazoliumkations sind. Die Eigenschaften der eingebetteten ionischen Flüssigkeiten sind für die Ionogele funktionsgebend. Die Funktionalität der jeweiligen Gele und damit der Transfer der Eigenschaften von ionischen Flüssigkeiten auf die Ionogele wurde in der vorliegenden Arbeit mittels zahlreicher Charakterisierungstechniken überprüft und bestätigt. In dieser Arbeit wurden durch Ionogelbildung makroskopische Ionogelobjekte in Form von Folien und Vliesen erzeugt. Dabei kamen das Filmgießen und das Elektrospinnen als Methoden zur Erzeugung dieser Folien und Vliese zum Einsatz, woraus jeweils ein Modellsystem resultiert. Dadurch wird die vorliegende Arbeit in die Themenkomplexe „elektrisch halbleitende Ionogelfolien“ und „antimikrobiell aktive Ionogelvliese“ gegliedert. Der Einsatz von triiodidhaltigen ionischen Flüssigkeiten und einer Polymermatrix in einem diskontinuierlichen Gießprozess resultiert in elektrisch halbleitenden Ionogelfolien. Die flexiblen und transparenten Folien können Mittelpunkt zahlreicher neuer Anwendungsfelder im Bereich flexibler Elektronik sein. Das Elektrospinnen von Polymethylmethacrylat mit einer ionischen Flüssigkeit führte zu einem homogen Ionogelvlies, welches ein Modell für die Übertragung antimikrobiell aktiver Eigenschaften ionischer Flüssigkeiten auf poröse Strukturen zur Filtration darstellt. Gleichzeitig ist es das erste Beispiel für ein kupferchloridhaltiges Ionogel. Ionogele sind attraktive Materialien mit zahlreichen Anwendungsmöglichkeiten. Mit der vorliegenden Arbeit wird das Spektrum der Ionogele um ein elektrisch halbleitendes und ein antimikrobiell aktives Ionogel erweitert. Gleichzeitig wurden durch diese Arbeit der Gruppe der ionischen Flüssigkeiten drei Beispiele für elektrisch halbleitende ionische Flüssigkeiten sowie zahlreiche kupfer(II)chloridbasierte ionische Flüssigkeiten hinzugefügt. KW - Ionogel KW - Polymerionogel KW - ionische Flüssigkeit KW - Polymethylmethacrylat KW - ionogel KW - polymer ionogel KW - ionic liquid KW - Poly(methyl methacrylate Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-532874 ER - TY - THES A1 - Altabal, Osamah T1 - Design and fabrication of geometry-assisted on-demand dosing systems N2 - The controlled dosage of substances from a device to its environment, such as a tissue or an organ in medical applications or a reactor, room, machinery or ecosystem in technical, should ideally match the requirements of the applications, e.g. in terms of the time point at which the cargo is released. On-demand dosage systems may enable such a desired release pattern, if the device contain suitable features that can translate external signals into a release function. This study is motivated by the opportunities arising from microsystems capable of an on-demand release and the contributions that geometrical design may have in realizing such features. The goals of this work included the design, fabrication, characterization and experimental proof-of-concept of geometry-assisted triggerable dosing effect (a) with a sequential dosing release and (b) in a self-sufficient dosage system. Structure-function relationships were addressed on the molecular, morphological and, with a particular attention, the device design level, which is on the micrometer scale. Models and/or computational tools were used to screen the parameter space and provide guidance for experiments. N2 - Die kontrollierte Freisetzung von Substanzen aus einem Device in seine Umgebung, wie ein Gewebe oder Organ in medizinischen Anwendungen oder ein Reaktor, ein Raum, ein Gerät oder ein Ökosystem in technischer Nutzung sollte idealerweise den Anforderungen des Einsatzzweckes entsprechen, beispielsweise hinsichtlich des Zeitpunktes an dem die Freisetzung erfolgt. On-demand Freisetzungssysteme könnten eine derartiges gewünschtes Verhalten zeigen, wenn das System die Befähigung besitzt, externe Signale in eine Freisetzungsfunktion zu überführen. Diese Arbeit greift die Möglichkeiten auf, die sich durch den Einsatz und ein gezieltes Design von mikrostrukturierten Systemen für die Realisierung einer on-demand Freisetzung ergeben könnten. Die Ziele der Arbeit umfassen die Konzeptionierung, Herstellung, Charakterisierung sowie den grundsätzlichen Nachweis durch Stimuli induzierten on-demand Freisetzungsfunktion einerseits in Form eines sequentiellen Freigabeverhaltens und anderseits in Form eines autarken (kontaktfrei ausgelösten) Dosiersystems. Struktur-Eigenschafts-Beziehungen wurden auf molekularer, morphologischer und - mit besonderen Augenmerk - auf der Ebene des Device-Designs untersucht. Modelle und/oder Computer-gestützte Verfahren wurden verwendet um geeignete Materialparameter zu identifizieren und einen Leitfaden für die Experimente bereitzustellen. KW - Stress concentration KW - Negative Poisson’s ratio KW - On-demand release KW - Spannungskonzentrationen KW - Negatives Poisson-Verhältnis KW - On-demand Freisetzung Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-532441 ER - TY - THES A1 - Kirchhofer, Tabea T1 - The development of multi - compartmentalised systems for the directed organisation of artificial cells N2 - Membrane contact sites are of particular interest in the field of synthetic biology and biophysics. They are involved in a great variety of cellular functions. They form in between two cellular organelles or an organelle and the plasma membrane in order to establish a communication path for molecule transport or signal transmission. The development of an artificial membrane system which can mimic membrane contact sites using bottom up synthetic biology was the goal of this research study. For this, a multi - compartmentalised giant unilamellar vesicle (GUV) system was created with the membrane of the outer vesicle mimicking the plasma membrane and the inner GUVs posing as cellular organelles. In the following steps, three different strategies were used to achieve an internal membrane - membrane adhesion. N2 - Viele bedeutende Prozesse einer Zelle spielen sich an den Berührungsstellen zwischen Zellmembranen und auch zwischen Zellmembranen und der Plasmamembran ab. An diesen, aus spezifischen Lipiden und Proteinen aufgebauten Kontaktstellen, können auf Grund der geringen Entfernung Signale und auch Moleküle ausgetauscht werden. Ziel dieses Forschungsprojektes war die Entwicklung eines künstlichen Zellmembransystems, das in der Lage ist diese Kontaktstellen nachzubilden. Dafür wurden multikompartmentalisierte riesige unilamellare Vesikel (GUVs) aufgebaut. Dies bedeutet, dass sich ein GUV innerhalb eines anderen GUVs befindet. Das äußere Vesikel bildet in diesem System die Plasma Membran, während das Innere als Zellorganelle fungiert. Dieses System wird auch als Vesosom bezeichnet. Im Folgenden wurden drei verschiedene Strategien entwickelt, um interne Haftung (Adhäsion) zwischen den Membranen zu erzeugen. KW - vesicle studies KW - membrane science KW - synthetic biology KW - internal membrane-membrane adhesion KW - artificial cells KW - multi-compartmentalised vesicles KW - künstliche Zellen KW - interne Membran-Membran Adhäsion KW - Membranforschung bzw. Membranwissenschaften KW - multi-kompartmentalisierte Vesikel KW - Synthetische Biologie KW - Vesikel Forschung/Vesikel Studien Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-528428 ER - TY - GEN A1 - Schneider, Matthias A1 - Fritzsche, Nora A1 - Puciul-Malinowska, Agnieszka A1 - Balis, Andrzej A1 - Mostafa, Amr A1 - Bald, Ilko A1 - Zapotoczny, Szczepan A1 - Taubert, Andreas T1 - Surface etching of 3D printed poly(lactic acid) with NaOH: a systematic approach T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - The article describes a systematic investigation of the effects of an aqueous NaOH treatment of 3D printed poly(lactic acid) (PLA) scaffolds for surface activation. The PLA surface undergoes several morphology changes and after an initial surface roughening, the surface becomes smoother again before the material dissolves. Erosion rates and surface morphologies can be controlled by the treatment. At the same time, the bulk mechanical properties of the treated materials remain unaltered. This indicates that NaOH treatment of 3D printed PLA scaffolds is a simple, yet viable strategy for surface activation without compromising the mechanical stability of PLA scaffolds. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1212 KW - surface modification KW - sodium hydroxide etching KW - poly(lactic acid) KW - 3D printing KW - roughness KW - wettability KW - erosion Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-525088 SN - 1866-8372 IS - 8 ER - TY - GEN A1 - Breternitz, Joachim A1 - Lehmann, Frederike A1 - Barnett, Sarah A. A1 - Nowell, Harriott A1 - Schorr, Susan T1 - Zur Rolle der Iodid-Methylammonium-Interaktion in der Ferroelektrizität in CH3NH3PbI3 T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - Ihre außergewöhnlich hohen Konversionseffizienzen von über 20 % und die einfache Zellherstellung machen Hybridperowskite zu heißen Kandidaten für alternative Solarzellenmaterialien. CH3NH3PbI3 als Archetyp dieser Materialklasse besitzt außergewöhnliche Eigenschaften wie eine sehr effiziente Umwandlung von Solarenergie, wobei besonders Ferroelektrizität als mögliche Erklärung in den Fokus gerückt ist. Diese erfordert allerdings eine nicht-zentrosymmetrische Kristallstruktur als notwendige Voraussetzung. Wir stellen hier eine Erklärung des Symmetriebruchs in diesem Material auf kristallographischem, d. h. fernordnungs-basiertem, Wege vor. Während das Molekülkation CH3NH3+ intrinsisch polar ist, ist es extrem fehlgeordnet und kann deshalb nicht die einzige Erklärung darstellen. Es verzerrt allerdings das umgebende Kristallgitter und ruft dadurch eine Verschiebung der Iod-Atome von den zentrosymmetrischen Positionen hervor. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1199 KW - ferroelectricity KW - hybrid perovskites KW - inorganic chemistry KW - photovoltaic materials KW - structure elucidation Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-525674 SN - 1866-8372 IS - 1 ER - TY - GEN A1 - Breternitz, Joachim A1 - Lehmann, Frederike A1 - Barnett, Sarah A. A1 - Nowell, Harriott A1 - Schorr, Susan T1 - Role of the Iodide-methylammonium interaction in the ferroelectricity of CH3NH3PbI3 T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - Excellent conversion efficiencies of over 20% and facile cell production have placed hybrid perovskites at the forefront of novel solar cell materials, with CH3NH3PbI3 being an archetypal compound. The question why CH3NH3PbI3 has such extraordinary characteristics, particularly a very efficient power conversion from absorbed light to electrical power, is hotly debated, with ferroelectricity being a promising candidate. This does, however, require the crystal structure to be non-centrosymmetric and we herein present crystallographic evidence as to how the symmetry breaking occurs on a crystallographic and, therefore, long-range level. Although the molecular cation CH3NH3+ is intrinsically polar, it is heavily disordered and this cannot be the sole reason for the ferroelectricity. We show that it, nonetheless, plays an important role, as it distorts the neighboring iodide positions from their centrosymmetric positions. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1196 KW - ferroelectricity KW - hybrid perovskites KW - inorganic chemistry KW - photovoltaic materials KW - structure elucidation Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-518227 SN - 1866-8372 IS - 1 ER - TY - THES A1 - Dambowsky, Ina T1 - Bioinspirierte Komposite - Strukturbildung durch Verkleben von Nano- oder Mesokristallen mit funktionalisierten Poly(2-oxazolin)en T1 - Bioinspired composites - structure formation by gluing of nano- or mesocrystals with functionalized poly(2-oxazoline)s N2 - Die herausragenden mechanischen Eigenschaften natürlicher anorganisch-organischer Kompositmaterialien wie Knochen oder Muschelschalen entspringen ihrer hierarchischen Struktur, die von der nano- bis hinauf zur makroskopischen Ebene reicht, und einer kontrollierten Verbindung entlang der Grenzflächen der anorganischen und organischen Komponenten. Ausgehend von diesen Schlüsselprinzipien des biologischen Materialdesigns wurden in dieser Arbeit zwei Konzepte für die bioinspirierte Strukturbildung von Kompositen untersucht, die auf dem Verkleben von Nano- oder Mesokristallen mit funktionalisierten Poly(2-oxazolin)-Blockcopolymeren beruhen sowie deren Potenzial zur Herstellung bioinspirierter selbstorganisierter hierarchischer anorganisch-organischer Verbundstrukturen ohne äußere Kräfte beleuchtet. Die Konzepte unterschieden sich in den verwendeten anorganischen Partikeln und in der Art der Strukturbildung. Über einen modularen Ansatz aus Polymersynthese und polymeranaloger Thiol-En-Funktionalisierung wurde erfolgreich eine Bibliothek von Poly(2-oxazolin)en mit unterschiedlichen Funktionalitäten erstellt. Die Blockcopolymere bestehen aus einem kurzen partikelaffinen "Klebeblock", der aus Thiol-En-funktionalisiertem Poly(2-(3-butenyl)-2-oxazolin) besteht, und einem langen wasserlöslichen, strukturbildenden Block, der aus thermoresponsivem und kristallisierbarem Poly(2-isopropyl-2-oxazolin) besteht und hierarchische Morphologien ausbildet. Verschiedene analytische Untersuchungen wie Turbidimetrie, DLS, DSC, SEM oder XRD machten das thermoresponsive bzw. das Kristallisationsverhalten der Blockcopolymere in Abhängigkeit vom eingeführten Klebeblock zugänglich. Es zeigte sich, dass diese Polymere ein komplexes temperatur- und pH-abhängiges Trübungsverhalten aufweisen. Hinsichtlich der Kristallisation änderte der Klebeblock nicht die nanoskopische Kristallstruktur; er beeinflusste jedoch die Kristallisationszeit, den Kristallisationsgrad und die hierarchische Morphologie. Dieses Ergebnis wurde auf das unterschiedliche Aggregationsverhalten der Polymere in Wasser zurückgeführt. Für die Herstellung von Kompositen nutzte Konzept 1 mikrometergroße Kupferoxalat-Mesokristalle, die eine innere Nanostruktur aufweisen. Die Strukturbildung über den anorganischen Teil wurde durch das Verkleben und Anordnen dieser Partikel erstrebt. Konzept 1 ermöglichte homogene freistehende stabile Kompositfilme mit einem hohen anorganischen Anteil. Die Partikel-Polymer-Kombination vereinte jedoch ungünstige Eigenschaften in sich, d. h. ihre Längenskalen waren zu unterschiedlich, was die Selbstassemblierung der Partikel verhinderte. Aufgrund des geringen Aspektverhältnisses von Kupferoxalat blieb auch die gegenseitige Ausrichtung durch äußere Kräfte erfolglos. Im Ergebnis eignet sich das Kupferoxalat-Poly(2-oxazolin)-Modellsystem nicht für die Herstellung hierarchischer Kompositstrukturen. Im Gegensatz dazu verwendet Konzept 2 scheibenförmige Laponit®-Nanopartikel und kristallisierbare Blockcopolymere zur Strukturbildung über die organische Komponente durch polymervermittelte Selbstassemblierung. Komplementäre Analysemethoden (Zeta-Potenzial, DLS, SEM, XRD, DSC, TEM) zeigten sowohl eine kontrollierte Wechselwirkung zwischen den Komponenten in wässriger Umgebung als auch eine kontrollierte Strukturbildung, die in selbstassemblierten Nanokompositen resultiert, deren Struktur sich über mehrere Längenskalen erstreckt. Es wurde gezeigt, dass die negativ geladenen Klebeblöcke spezifisch und selektiv an den positiv geladenen Rändern der Laponit®-Partikel binden und so Polymer-Laponit®-Nanohybridpartikel entstehen, die als Grundbausteine für die Kompositbildung dienen. Die Hybridpartikel sind bei Raumtemperatur elektrosterisch stabilisiert - sterisch durch ihre langen, mit Wasser wechselwirkenden Poly(2-isopropyl-2-oxazolin)-Blöcke und elektrostatisch über die negativ geladenen Laponit®-Flächen. Im Ergebnis ließ sich Konzept 2 und damit die Strukturbildung über die organische Komponente erfolgreich umsetzten. Das Laponit®-Poly(2-oxazolin)-Modellsystem eröffnete den Weg zu selbstassemblierten geschichteten quasi-hierarchischen Nanokompositstrukturen mit hohem anorganischen Anteil. Abhängig von der frei verfügbaren Polymerkonzentration bei der Kompositbildung entstanden zwei unterschiedliche Komposit-Typen. Darüber hinaus entwarf die Arbeit einen Erklärungsansatz für den polymervermittelten Bildungsprozess der Komposit-Strukturen. Insgesamt legt diese Arbeit Struktur-Prozess-Eigenschafts-Beziehungen offen, um selbstassemblierte bioinspirierte Kompositstrukturen zu bilden und liefert neue Einsichten zu einer geeigneten Kombination an Komponenten und Herstellungsbedingungen, die eine kontrollierte selbstassemblierte Strukturbildung mithilfe funktionalisierter Poly(2-oxazolin)-Blockcopolymere erlauben. N2 - Natural inorganic-organic composite materials like nacre and bone feature unique mechanical properties due to their complex hierarchical structure and their controlled connection at the interface of the components, starting from the nanometer scale. Following these key principles of biological material design, this thesis investigates two concepts for bioinspired structure formation of composites based on gluing nano- or mesocrystals with functionalized poly(2-oxazoline) block copolymers and the potential of these materials for fabricating bioinspired self-assembled hierarchical inorganic-organic composite structures without external forces. The concepts differed in the inorganic particles used and in the structure formation pathway. A modular approach of polymer synthesis and polymer analogue thiol-ene modification was successfully used to create a platform of poly(2-oxazoline)s with different functionalities. The block copolymers are composed of a short particle-affine "gluing block" consisting of thiol-ene modified poly(2-(3-butenyl)-2-oxazoline) and a long water soluble, structure forming block that consists of thermoresponsive and crystallizable poly(2-isopropyl-2-oxazoline) that yields hierarchical morphologies. Various analytical investigations such as turbidimetry, DLS, DSC, SEM and XRD revealed the influence of the "gluing block" on the thermoresponsive and crystallization behavior of the block copolymers. It was shown that these polymers have complex temperature- and pH-dependent turbidity behavior. Concerning crystallization, the gluing block did not change the nanoscopic crystal structure but influenced the crystallization time, the degree of crystallization and the hierarchical morphology. This result was attributed to different aggregation behavior of the polymers in water. For the composite fabrication, concept 1 uses micrometer-sized copper oxalate mesocrystals, which exhibit an internal nanostructure and seek structure formation via the inorganic part by the assembly of these particles. Concept 1 enabled homogeneous free-standing stable composite films with high inorganic content. However, the particle-polymer combination combined unfavorable properties, i.e. their length scales were too different, which prevented the particles from self-assembling. Furthermore, due to the small aspect ratio of copper oxalate, mutual alignment via external forces was also unsuccessful. In essence, the copper oxalate-poly(2-oxazoline)-model system is not suitable for the fabrication of hierarchical composite structures. In contrast, concept 2 uses disc-shaped Laponite® nanoparticles and crystallizable block copolymers for structure formation via the organic component by polymer-mediated self-assembly. Complementary analytical methods (zeta potential, DLS, SEM, XRD, DSC, TEM) revealed both controlled interaction between the components in an aqueous environment and a controlled structure formation to yield self-assembled nanocomposites, whose structure spans several length scales. It was shown that the negatively charged gluing blocks bind specifically and selectively to the positively charged Laponite® particle rim, resulting in polymer-Laponite® nanohybrid particles that served as the basic building blocks for composite formation. The hybrid particles are electrosterically stabilized at room temperature – sterically by their long water-interacting poly(2-isopropyl-2-oxazoline) blocks and electrostatically via the negatively charged Laponite® faces. As a result, concept 2 and thus structure formation via the organic component could be successfully achieved. The Laponite®-poly(2-oxazoline)-model system opened the path to self-assembled layered quasi-hierarchical nanocomposite structures with a high inorganic content. Depending on the free available polymer concentration during composite formation, two different composite types were accessible. Additionally, a possible explanation for the polymer-mediated formation process of the self-assembled composite structure was proposed. This thesis contributes insights in understanding the fundamental structure-process-property relationships in order to form self-assembled bioinspired composite structures and provides conditions and suitable compilation of components that allow a controlled self-assembled structure formation via poly(2-oxazoline) block copolymers. KW - bioinspirierte Komposite KW - anorganisch-organische Hybrid-Nanopartikel KW - Selbstassemblierung KW - thermoresponsiv KW - Poly(2-oxazolin)-Blockcopolymer KW - Polymerkristallisation KW - Thiol-En KW - inorganic-organic hybrid nanoparticle KW - self-assembly KW - thermoresponsive KW - poly(2-oxazoline) KW - block copolymer KW - polymer crystallization KW - thiol-ene KW - bioinspired composite Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-523671 ER - TY - GEN A1 - Perovic, Milena A1 - Qin, Qing A1 - Oschatz, Martin T1 - From molecular precursors to nanoparticles BT - tailoring the adsorption properties of porous carbon materials by controlled chemical functionalization T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - Nanoporous carbon materials (NCMs) provide the "function" of high specific surface area and thus have large interface area for interactions with surrounding species, which is of particular importance in applications related to adsorption processes. The strength and mechanism of adsorption depend on the pore architecture of the NCMs. In addition, chemical functionalization can be used to induce changes of electron density and/or electron density distribution in the pore walls, thus further modifying the interactions between carbons and guest species. Typical approaches for functionalization of nanoporous materials with regular atomic construction like porous silica, metal-organic frameworks, or zeolites, cannot be applied to NCMs due to their less defined local atomic construction and abundant defects. Therefore, synthetic strategies that offer a higher degree of control over the process of functionalization are needed. Synthetic approaches for covalent functionalization of NCMs, that is, for the incorporation of heteroatoms into the carbon backbone, are critically reviewed with a special focus on strategies following the concept "from molecules to materials." Approaches for coordinative functionalization with metallic species, and the functionalization by nanocomposite formation between pristine carbon materials and heteroatom-containing carbons, are introduced as well. Particular focus is given to the influences of these functionalizations in adsorption-related applications. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1191 KW - composites KW - heteroatoms KW - metal species KW - porous carbon materials KW - surface functionalization Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-516140 SN - 1866-8372 ER - TY - GEN A1 - Schönemann, Eric A1 - Koc, Julian A1 - Aldred, Nick A1 - Clare, Anthony S. A1 - Laschewsky, André A1 - Rosenhahn, Axel A1 - Wischerhoff, Erik T1 - Synthesis of novel sulfobetaine polymers with differing dipole orientations in their side chains, and their effects on the antifouling properties T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - The impact of the orientation of zwitterionic groups, with respect to the polymer backbone, on the antifouling performance of thin hydrogel films made of polyzwitterions is explored. In an extension of the recent discussion about differences in the behavior of polymeric phosphatidylcholines and choline phosphates, a quasi-isomeric set of three poly(sulfobetaine methacrylate)s is designed for this purpose. The design is based on the established monomer 3-[N-2-(methacryloyloxy)ethyl-N,N-dimethyl]ammonio-propane-1-sulfonate and two novel sulfobetaine methacrylates, in which the positions of the cationic and the ionic groups relative to the polymerizable group, and thus also to the polymer backbone, are altered. The effect of the varied segmental dipole orientation on their water solubility, wetting behavior by water, and fouling resistance is compared. As model systems, the adsorption of the model proteins bovine serum albumin (BSA), fibrinogen, and lysozyme onto films of the various polyzwitterion surfaces is studied, as well as the settlement of a diatom (Navicula perminuta) and barnacle cyprids (Balanus improvisus) as representatives of typical marine fouling communities. The results demonstrate the important role of the zwitterionic group's orientation on the polymer behavior and fouling resistance T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1184 KW - antifouling KW - coatings KW - crosslinking KW - hydrophilic polymers KW - polyzwitterions Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-524820 SN - 1866-8372 IS - 1 ER - TY - GEN A1 - Walkowiak, Jacek A1 - Lu, Yan A1 - Gradzielski, Michael A1 - Zauscher, Stefan A1 - Ballauff, Matthias T1 - Thermodynamic analysis of the uptake of a protein in a spherical polyelectrolyte brush T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - A thermodynamic study of the adsorption of Human Serum Albumin (HSA) onto spherical polyelectrolyte brushes (SPBs) by isothermal titration calorimetry (ITC) is presented. The SPBs are composed of a solid polystyrene core bearing long chains of poly(acrylic acid). ITC measurements done at different temperatures and ionic strengths lead to a full set of thermodynamicbinding constants together with the enthalpies and entropies of binding. The adsorption of HSA onto SPBs is described with a two-step model. The free energy of binding Delta Gb depends only weakly on temperature because of a marked compensation of enthalpy by entropy. Studies of the adsorbed HSA by Fourier transform infrared spectroscopy (FT-IR) demonstrate no significant disturbance in the secondary structure of the protein. The quantitative analysis demonstrates that counterion release is the major driving force for adsorption in a process where proteins become multivalent counterions of the polyelectrolyte chains upon adsorption. A comparison with the analysis of other sets of data related to the binding of HSA to polyelectrolytes demonstrates that the cancellation of enthalpy and entropy is a general phenomenon that always accompanies the binding of proteins to polyelectrolytes dominated by counterion release. KW - ITC KW - spherical polyelectrolyte brushes KW - enthalpy-entropy compensation (EEC) KW - proteins KW - thermodynamics Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-517307 SN - 1866-8372 IS - 1 ER - TY - GEN A1 - Nicolai, Merle Marie A1 - Weishaupt, Ann-Kathrin A1 - Baesler, Jessica A1 - Brinkmann, Vanessa A1 - Wellenberg, Anna A1 - Winkelbeiner, Nicola Lisa A1 - Gremme, Anna A1 - Aschner, Michael A1 - Fritz, Gerhard A1 - Schwerdtle, Tanja A1 - Bornhorst, Julia T1 - Effects of manganese on genomic integrity in the multicellular model organism Caenorhabditis elegans T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - Although manganese (Mn) is an essential trace element, overexposure is associated with Mn-induced toxicity and neurological dysfunction. Even though Mn-induced oxidative stress is discussed extensively, neither the underlying mechanisms of the potential consequences of Mn-induced oxidative stress on DNA damage and DNA repair, nor the possibly resulting toxicity are characterized yet. In this study, we use the model organism Caenorhabditis elegans to investigate the mode of action of Mn toxicity, focusing on genomic integrity by means of DNA damage and DNA damage response. Experiments were conducted to analyze Mn bioavailability, lethality, and induction of DNA damage. Different deletion mutant strains were then used to investigate the role of base excision repair (BER) and dePARylation (DNA damage response) proteins in Mn-induced toxicity. The results indicate a dose- and time-dependent uptake of Mn, resulting in increased lethality. Excessive exposure to Mn decreases genomic integrity and activates BER. Altogether, this study characterizes the consequences of Mn exposure on genomic integrity and therefore broadens the molecular understanding of pathways underlying Mn-induced toxicity. Additionally, studying the basal poly(ADP-ribosylation) (PARylation) of worms lacking poly(ADP-ribose) glycohydrolase (PARG) parg-1 or parg-2 (two orthologue of PARG), indicates that parg-1 accounts for most of the glycohydrolase activity in worms. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1173 KW - manganese KW - oxidative stress KW - DNA repair KW - DNA damage response KW - Caenorhabditis elegans Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-523275 SN - 1866-8372 IS - 1173 ER - TY - GEN A1 - Kopyra, Janina A1 - Wierzbicka, Paulina A1 - Tulwin, Adrian A1 - Thiam, Guillaume A1 - Bald, Ilko A1 - Rabilloud, Franck A1 - Abdoul-Carime, Hassan T1 - Experimental and theoretical studies of dissociative electron attachment to metabolites oxaloacetic and citric acids T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - In this contribution the dissociative electron attachment to metabolites found in aerobic organisms, namely oxaloacetic and citric acids, was studied both experimentally by means of a crossed-beam setup and theoretically through density functional theory calculations. Prominent negative ion resonances from both compounds are observed peaking below 0.5 eV resulting in intense formation of fragment anions associated with a decomposition of the carboxyl groups. In addition, resonances at higher energies (3–9 eV) are observed exclusively from the decomposition of the oxaloacetic acid. These fragments are generated with considerably smaller intensities. The striking findings of our calculations indicate the different mechanism by which the near 0 eV electron is trapped by the precursor molecule to form the transitory negative ion prior to dissociation. For the oxaloacetic acid, the transitory anion arises from the capture of the electron directly into some valence states, while, for the citric acid, dipole- or multipole-bound states mediate the transition into the valence states. What is also of high importance is that both compounds while undergoing DEA reactions generate highly reactive neutral species that can lead to severe cell damage in a biological environment. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1156 KW - dissociative electron attachment KW - negative ions KW - oxaloacetic acid KW - citric acid KW - mass spectrometry Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-521829 SN - 1866-8372 IS - 1156 ER - TY - GEN A1 - Block, Inga A1 - Günter, Christina A1 - Rodrigues, Alysson Duarte A1 - Paasch, Silvia A1 - Hesemann, Peter A1 - Taubert, Andreas T1 - Carbon Adsorbents from Spent Coffee for Removal of Methylene Blue and Methyl Orange from Water T2 - Postprints der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe N2 - Activated carbons (ACs) were prepared from dried spent coffee (SCD), a biological waste product, to produce adsorbents for methylene blue (MB) and methyl orange (MO) from aqueous solution. Pre-pyrolysis activation of SCD was achieved via treatment of the SCD with aqueous sodium hydroxide solutions at 90 °C. Pyrolysis of the pretreated SCD at 500 °C for 1 h produced powders with typical characteristics of AC suitable and effective for dye adsorption. As an alternative to the rather harsh base treatment, calcium carbonate powder, a very common and abundant resource, was also studied as an activator. Mixtures of SCD and CaCO3 (1:1 w/w) yielded effective ACs for MO and MB removal upon pyrolysis needing only small amounts of AC to clear the solutions. A selectivity of the adsorption process toward anionic (MO) or cationic (MB) dyes was not observed. T3 - Zweitveröffentlichungen der Universität Potsdam : Mathematisch-Naturwissenschaftliche Reihe - 1155 KW - water KW - spent coffee KW - dye adsorption KW - methylene blue KW - methyl orange KW - calcium carbonate KW - activated carbon KW - water treatment KW - dye removal Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-521653 SN - 1866-8372 IS - 14 ER -