TY - JOUR A1 - Turner, Sarah T. A1 - Pingel, Patrick A1 - Steyrleuthner, Robert A1 - Crossland, Edward J. W. A1 - Ludwigs, Sabine A1 - Neher, Dieter T1 - Quantitative analysis of bulk heterojunction films using linear absorption spectroscopy and solar cell performance JF - Advanced functional materials N2 - A fundamental understanding of the relationship between the bulk morphology and device performance is required for the further development of bulk heterojunction organic solar cells. Here, non-optimized (chloroform cast) and nearly optimized (solvent-annealed o-dichlorobenzene cast) P3HT:PCBM blend films treated over a range of annealing temperatures are studied via optical and photovoltaic device measurements. Parameters related to the P3HT aggregate morphology in the blend are obtained through a recently established analytical model developed by F. C. Spano for the absorption of weakly interacting H-aggregates. Thermally induced changes are related to the glass transition range of the blend. In the chloroform prepared devices, the improvement in device efficiency upon annealing within the glass transition range can be attributed to the growth of P3HT aggregates, an overall increase in the percentage of chain crystallinity, and a concurrent increase in the hole mobilities. Films treated above the glass transition range show an increase in efficiency and fill factor not only associated with the change in chain crystallinity, but also with a decrease in the energetic disorder. On the other hand, the properties of the P3HT phase in the solvent-annealed o-dichlorobenzene cast blends are almost indistinguishable from those of the corresponding pristine P3HT layer and are only weakly affected by thermal annealing. Apparently, slow drying of the blend allows the P3HT chains to crystallize into large domains with low degrees of intra- and interchain disorder. This morphology appears to be most favorable for the efficient generation and extraction of charges. KW - Organic electronics KW - morphology KW - solar cells KW - mobility KW - absorption spectroscopy Y1 - 2011 U6 - https://doi.org/10.1002/adfm.201101583 SN - 1616-301X VL - 21 IS - 24 SP - 4640 EP - 4652 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Tremel, Kim A1 - Fischer, Florian S. U. A1 - Kayunkid, Navaphun A1 - Di Pietro, Riccardo A1 - Tkachov, Roman A1 - Kiriy, Anton A1 - Neher, Dieter A1 - Ludwigs, Sabine A1 - Brinkmann, Martin T1 - Charge transport anisotropy in highly oriented thin films of the acceptor polymer P(NDI2OD-T2) JF - dvanced energy materials N2 - The nanomorphology of the high mobility polymer poly{[N,N'-bis(2-octyldodecyl)-1,4,5,8-naphthalenedicarboximide-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)} P(NDI2OD-T2) in thin films is explored as a function of different annealing conditions and correlated to optical and electrical properties. While nanofibrils with face-on orientation in form I are obtained directly after spin-coating and annealing below the melt transition temperature, clear evidence of lamellar structures is found after melt-annealing followed by slow cooling to room temperature. Interestingly these structural changes are accompanied by distinct changes in the absorption patterns. Electron diffraction measurements further show clear transitions towards predominant edge-on oriented chains in form II upon melt-annealing. Large-scale alignment with dichroic ratios up to 10 and improved order is achieved by high temperature rubbing and subsequent post-rubbing annealing. These highly oriented morphologies allow anisotropic in-plane charge transport to be probed with top-gate transistors parallel and perpendicular to the polymer chain direction. Mobilities up to 0.1 cm(2) V-1 s(-1) are observed parallel to the polymer chain, which is up to 10 times higher than those perpendicular to the polymer chain. Y1 - 2014 U6 - https://doi.org/10.1002/aenm.201301659 SN - 1614-6832 SN - 1614-6840 VL - 4 IS - 10 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Tokmoldin, Nurlan A1 - Vollbrecht, Joachim A1 - Hosseini, Seyed Mehrdad A1 - Sun, Bowen A1 - Perdigón-Toro, Lorena A1 - Woo, Han Young A1 - Zou, Yingping A1 - Neher, Dieter A1 - Shoaee, Safa T1 - Explaining the fill-factor and photocurrent losses of nonfullerene acceptor-based solar cells by probing the long-range charge carrier diffusion and drift lengths JF - Advanced energy materials N2 - Organic solar cells (OSC) nowadays match their inorganic competitors in terms of current production but lag behind with regards to their open-circuit voltage loss and fill-factor, with state-of-the-art OSCs rarely displaying fill-factor of 80% and above. The fill-factor of transport-limited solar cells, including organic photovoltaic devices, is affected by material and device-specific parameters, whose combination is represented in terms of the established figures of merit, such as theta and alpha. Herein, it is demonstrated that these figures of merit are closely related to the long-range carrier drift and diffusion lengths. Further, a simple approach is presented to devise these characteristic lengths using steady-state photoconductance measurements. This yields a straightforward way of determining theta and alpha in complete cells and under operating conditions. This approach is applied to a variety of photovoltaic devices-including the high efficiency nonfullerene acceptor blends-and show that the diffusion length of the free carriers provides a good correlation with the fill-factor. It is, finally, concluded that most state-of-the-art organic solar cells exhibit a sufficiently large drift length to guarantee efficient charge extraction at short circuit, but that they still suffer from too small diffusion lengths of photogenerated carriers limiting their fill factor. KW - diffusion length KW - drift length KW - figure of merit KW - lifetime‐ mobility product KW - steady‐ state photoconductance Y1 - 2021 U6 - https://doi.org/10.1002/aenm.202100804 SN - 1614-6840 VL - 11 IS - 22 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Tokmoldin, Nurlan A1 - Hosseini, Seyed Mehrdad A1 - Raoufi, Meysam A1 - Phuong, Le Quang A1 - Sandberg, Oskar J. A1 - Guan, Huilan A1 - Zou, Yingping A1 - Neher, Dieter A1 - Shoaee, Safa T1 - Extraordinarily long diffusion length in PM6:Y6 organic solar cells JF - Journal of materials chemistry : A, materials for energy and sustainability N2 - The PM6:Y6 bulk-heterojunction (BHJ) blend system achieves high short-circuit current (J(SC)) values in thick photovoltaic junctions. Here we analyse these solar cells to understand the observed independence of the short-circuit current upon photoactive layer thickness. We employ a range of optoelectronic measurements and analyses, including Mott-Schottky analysis, CELIV, photoinduced absorption spectroscopy, mobility measurements and simulations, to conclude that, the invariant photocurrent for the devices with different active layer thicknesses is associated with the Y6's diffusion length exceeding 300 nm in case of a 300 nm thick cell. This is despite unintentional doping that occurs in PM6 and the associated space-charge effect, which is expected to be even more profound upon photogeneration. This extraordinarily long diffusion length - which is an order of magnitude larger than typical values for organics - dominates transport in the flat-band region of thick junctions. Our work suggests that the performance of the doped PM6:Y6 organic solar cells resembles that of inorganic devices with diffusion transport playing a pivotal role. Ultimately, this is expected to be a key requirement for the fabrication of efficient, high-photocurrent, thick organic solar cells. Y1 - 2020 U6 - https://doi.org/10.1039/d0ta03016c SN - 2050-7488 SN - 2050-7496 VL - 8 IS - 16 SP - 7854 EP - 7860 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Tockhorn, Philipp A1 - Sutter, Johannes A1 - Cruz Bournazou, Alexandros A1 - Wagner, Philipp A1 - Jäger, Klaus A1 - Yoo, Danbi A1 - Lang, Felix A1 - Grischek, Max A1 - Li, Bor A1 - Li, Jinzhao A1 - Shargaieva, Oleksandra A1 - Unger, Eva A1 - Al-Ashouri, Amran A1 - Köhnen, Eike A1 - Stolterfoht, Martin A1 - Neher, Dieter A1 - Schlatmann, Rutger A1 - Rech, Bernd A1 - Stannowski, Bernd A1 - Albrecht, Steve A1 - Becker, Christiane T1 - Nano-optical designs for high-efficiency monolithic perovskite-silicon tandem solar cells JF - Nature nanotechnology N2 - Designing gentle sinusoidal nanotextures enables the realization of high-efficiency perovskite-silicon solar cells
Perovskite-silicon tandem solar cells offer the possibility of overcoming the power conversion efficiency limit of conventional silicon solar cells. Various textured tandem devices have been presented aiming at improved optical performance, but optimizing film growth on surface-textured wafers remains challenging. Here we present perovskite-silicon tandem solar cells with periodic nanotextures that offer various advantages without compromising the material quality of solution-processed perovskite layers. We show a reduction in reflection losses in comparison to planar tandems, with the new devices being less sensitive to deviations from optimum layer thicknesses. The nanotextures also enable a greatly increased fabrication yield from 50% to 95%. Moreover, the open-circuit voltage is improved by 15 mV due to the enhanced optoelectronic properties of the perovskite top cell. Our optically advanced rear reflector with a dielectric buffer layer results in reduced parasitic absorption at near-infrared wavelengths. As a result, we demonstrate a certified power conversion efficiency of 29.80%. Y1 - 2022 U6 - https://doi.org/10.1038/s41565-022-01228-8 SN - 1748-3387 SN - 1748-3395 VL - 17 IS - 11 SP - 1214 EP - 1221 PB - Nature Publishing Group CY - London [u.a.] ER - TY - JOUR A1 - Tait, Claudia E. A1 - Reckwitz, Anna A1 - Arvind, Malavika A1 - Neher, Dieter A1 - Bittl, Robert A1 - Behrends, Jan T1 - Spin-spin interactions and spin delocalisation in a doped organic semiconductor probed by EPR spectroscopy JF - Physical chemistry, chemical physics : PCCP ; a journal of European chemical societies N2 - The enhancement and control of the electrical conductivity of organic semiconductors is fundamental for their use in optoelectronic applications and can be achieved by molecular doping, which introduces additional charge carriers through electron transfer between a dopant molecule and the organic semiconductor. Here, we use Electron Paramagnetic Resonance (EPR) spectroscopy to characterise the unpaired spins associated with the charges generated by molecular doping of the prototypical organic semiconductor poly(3-hexylthiophene) (P3HT) with 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F(4)TCNQ) and tris(pentafluorophenyl)borane (BCF). The EPR results reveal the P3HT radical cation as the only paramagnetic species in BCF-doped P3HT films and show evidence for increased mobility of the detected spins at high doping concentrations as well as formation of antiferromagnetically coupled spin pairs leading to decreased spin concentrations at low temperatures. The EPR signature for F(4)TCNQ-doped P3HT is found to be determined by spin exchange between P3HT radical cations and F(4)TCNQ radical anions. Results from continuous-wave and pulse EPR measurements suggest the presence of the unpaired spin on P3HT in a multitude of environments, ranging from free P3HT radical cations with similar properties to those observed in BCF-doped P3HT, to pairs of dipolar and exchange-coupled spins on P3HT and the dopant anion. Characterisation of the proton hyperfine interactions by ENDOR allowed quantification of the extent of spin delocalisation and revealed reduced delocalisation in the F(4)TCNQ-doped P3HT films. Y1 - 2021 U6 - https://doi.org/10.1039/d1cp02133h SN - 1463-9076 SN - 1463-9084 VL - 23 IS - 25 SP - 13827 EP - 13841 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Sun, Bowen A1 - Sandberg, Oskar A1 - Neher, Dieter A1 - Armin, Ardalan A1 - Shoaee, Safa T1 - Wave optics of differential absorption spectroscopy in thick-junction organic solar cells BT - optical artifacts and correction strategies JF - Physical review applied / The American Physical Society N2 - Differential absorption spectroscopy techniques serve as powerful techniques to study the excited species in organic solar cells. However, it has always been challenging to employ these techniques for characterizing thick-junction organic solar cells, especially when a reflective top contact is involved. In this work, we present a detailed and systematic study on how a combination of the presence of the interference effect and a nonuniform charge-distribution profile, severely manipulates experimental spectra and the decay dynamics. Furthermore, we provide a practical methodology to correct these optical artifacts in differential absorption spectroscopies. The results and the proposed correction method generally apply to all kinds of differential absorption spectroscopy techniques and various thin-film systems, such as organics, perovskites, kesterites, and two-dimensional materials. Notably, it is found that the shape of differential absorption spectra can be strongly distorted, starting from 150-nm active-layer thickness; this matches the thickness range of thick-junction organic solar cells and most perovskite solar cells and needs to be carefully considered in experiments. In addition, the decay dynamics of differential absorption spectra is found to be disturbed by optical artifacts under certain conditions. With the help of the proposed correction formalism, differential spectra and the decay dynamics can be characterized on the full device of thin-film solar cells in transmission mode and yield accurate and reliable results to provide design rules for further progress. Y1 - 2022 U6 - https://doi.org/10.1103/PhysRevApplied.17.054016 SN - 2331-7019 VL - 17 IS - 5 PB - American Physical Society CY - College Park ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Wolff, Christian Michael A1 - Marquez, Jose A. A1 - Zhang, Shanshan A1 - Hages, Charles J. A1 - Rothhardt, Daniel A1 - Albrecht, Steve A1 - Burn, Paul L. A1 - Meredith, Paul A1 - Unold, Thomas A1 - Neher, Dieter T1 - Visualization and suppression of interfacial recombination for high-efficiency large-area pin perovskite solar cells JF - Nature Energy N2 - The performance of perovskite solar cells is predominantly limited by non-radiative recombination, either through trap-assisted recombination in the absorber layer or via minority carrier recombination at the perovskite/transport layer interfaces. Here, we use transient and absolute photoluminescence imaging to visualize all non-radiative recombination pathways in planar pintype perovskite solar cells with undoped organic charge transport layers. We find significant quasi-Fermi-level splitting losses (135 meV) in the perovskite bulk, whereas interfacial recombination results in an additional free energy loss of 80 meV at each individual interface, which limits the open-circuit voltage (V-oc) of the complete cell to similar to 1.12 V. Inserting ultrathin interlayers between the perovskite and transport layers leads to a substantial reduction of these interfacial losses at both the p and n contacts. Using this knowledge and approach, we demonstrate reproducible dopant-free 1 cm(2) perovskite solar cells surpassing 20% efficiency (19.83% certified) with stabilized power output, a high V-oc (1.17 V) and record fill factor (>81%). KW - Energy science and technology KW - Solar cells Y1 - 2018 U6 - https://doi.org/10.1038/s41560-018-0219-8 SN - 2058-7546 VL - 3 IS - 10 SP - 847 EP - 854 PB - Nature Publ. Group CY - London ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Wolff, Christian Michael A1 - Amir, Yohai A1 - Paulke, Andreas A1 - Perdigón-Toro, Lorena A1 - Caprioglio, Pietro A1 - Neher, Dieter T1 - Approaching the fill factor Shockley-Queisser limit in stable, dopant-free triple cation perovskite solar cells JF - Energy & Environmental Science N2 - Perovskite solar cells now compete with their inorganic counterparts in terms of power conversion efficiency, not least because of their small open-circuit voltage (V-OC) losses. A key to surpass traditional thin-film solar cells is the fill factor (FF). Therefore, more insights into the physical mechanisms that define the bias dependence of the photocurrent are urgently required. In this work, we studied charge extraction and recombination in efficient triple cation perovskite solar cells with undoped organic electron/hole transport layers (ETL/HTL). Using integral time of flight we identify the transit time through the HTL as the key figure of merit for maximizing the fill factor (FF) and efficiency. Complementarily, intensity dependent photocurrent and V-OC measurements elucidate the role of the HTL on the bias dependence of non-radiative and transport-related loss channels. We show that charge transport losses can be completely avoided under certain conditions, yielding devices with FFs of up to 84%. Optimized cells exhibit power conversion efficiencies of above 20% for 6 mm(2) sized pixels and 18.9% for a device area of 1 cm(2). These are record efficiencies for hybrid perovskite devices with dopant-free transport layers, highlighting the potential of this device technology to avoid charge-transport limitations and to approach the Shockley-Queisser limit. Y1 - 2017 U6 - https://doi.org/10.1039/c7ee00899f SN - 1754-5692 SN - 1754-5706 VL - 10 SP - 1530 EP - 1539 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Le Corre, Vincent M. A1 - Feuerstein, Markus A1 - Caprioglio, Pietro A1 - Koster, Lambert Jan Anton A1 - Neher, Dieter T1 - Voltage-Dependent Photoluminescence and How It Correlates with the Fill Factor and Open-Circuit Voltage in Perovskite Solar Cells JF - Acs energy letters N2 - Optimizing the photoluminescence (PL) yield of a solar cell has long been recognized as a key principle to maximize the power conversion efficiency. While PL measurements are routinely applied to perovskite films and solar cells under open circuit conditions (V-OC), it remains unclear how the emission depends on the applied voltage. Here, we performed PL(V) measurements on perovskite cells with different hole transport layer thicknesses and doping concentrations, resulting in remarkably different fill factors (FFs). The results reveal that PL(V) mirrors the current-voltage (JV) characteristics in the power-generating regime, which highlights an interesting correlation between radiative and nonradiative recombination losses. In particular, high FF devices show a rapid quenching of PL(V) from open-circuit to the maximum power point. We conclude that, while the PL has to be maximized at V-OC at lower biases < V-OC the PL must be rapidly quenched as charges need to be extracted prior to recombination. Y1 - 2019 U6 - https://doi.org/10.1021/acsenergylett.9b02262 SN - 2380-8195 VL - 4 IS - 12 SP - 2887 EP - 2892 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Grischek, Max A1 - Caprioglio, Pietro A1 - Wolff, Christian Michael A1 - Gutierrez-Partida, Emilio A1 - Peña-Camargo, Francisco A1 - Rothhardt, Daniel A1 - Zhang, Shanshan A1 - Raoufi, Meysam A1 - Wolansky, Jakob A1 - Abdi-Jalebi, Mojtaba A1 - Stranks, Samuel D. A1 - Albrecht, Steve A1 - Kirchartz, Thomas A1 - Neher, Dieter T1 - How to quantify the efficiency potential of neat perovskite films BT - Perovskite semiconductors with an implied efficiency exceeding 28% JF - Advanced Materials N2 - Perovskite photovoltaic (PV) cells have demonstrated power conversion efficiencies (PCE) that are close to those of monocrystalline silicon cells; however, in contrast to silicon PV, perovskites are not limited by Auger recombination under 1-sun illumination. Nevertheless, compared to GaAs and monocrystalline silicon PV, perovskite cells have significantly lower fill factors due to a combination of resistive and non-radiative recombination losses. This necessitates a deeper understanding of the underlying loss mechanisms and in particular the ideality factor of the cell. By measuring the intensity dependence of the external open-circuit voltage and the internal quasi-Fermi level splitting (QFLS), the transport resistance-free efficiency of the complete cell as well as the efficiency potential of any neat perovskite film with or without attached transport layers are quantified. Moreover, intensity-dependent QFLS measurements on different perovskite compositions allows for disentangling of the impact of the interfaces and the perovskite surface on the non-radiative fill factor and open-circuit voltage loss. It is found that potassium-passivated triple cation perovskite films stand out by their exceptionally high implied PCEs > 28%, which could be achieved with ideal transport layers. Finally, strategies are presented to reduce both the ideality factor and transport losses to push the efficiency to the thermodynamic limit. KW - non-radiative interface recombination KW - perovskite solar cells KW - photoluminescence Y1 - 2020 U6 - https://doi.org/10.1002/adma.202000080 SN - 0935-9648 SN - 1521-4095 VL - 32 IS - 17 SP - 1 EP - 10 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Caprioglio, Pietro A1 - Wolff, Christian Michael A1 - Marquez, Jose A. A1 - Nordmann, Joleik A1 - Zhang, Shanshan A1 - Rothhardt, Daniel A1 - Hörmann, Ulrich A1 - Amir, Yohai A1 - Redinger, Alex A1 - Kegelmann, Lukas A1 - Zu, Fengshuo A1 - Albrecht, Steve A1 - Koch, Norbert A1 - Kirchartz, Thomas A1 - Saliba, Michael A1 - Unold, Thomas A1 - Neher, Dieter T1 - The impact of energy alignment and interfacial recombination on the internal and external open-circuit voltage of perovskite solar cells JF - Energy & environmental science N2 - Charge transport layers (CTLs) are key components of diffusion controlled perovskite solar cells, however, they can induce additional non-radiative recombination pathways which limit the open circuit voltage (V-OC) of the cell. In order to realize the full thermodynamic potential of the perovskite absorber, both the electron and hole transport layer (ETL/HTL) need to be as selective as possible. By measuring the photoluminescence yield of perovskite/CTL heterojunctions, we quantify the non-radiative interfacial recombination currents in pin- and nip-type cells including high efficiency devices (21.4%). Our study comprises a wide range of commonly used CTLs, including various hole-transporting polymers, spiro-OMeTAD, metal oxides and fullerenes. We find that all studied CTLs limit the V-OC by inducing an additional non-radiative recombination current that is in most cases substantially larger than the loss in the neat perovskite and that the least-selective interface sets the upper limit for the V-OC of the device. Importantly, the V-OC equals the internal quasi-Fermi level splitting (QFLS) in the absorber layer only in high efficiency cells, while in poor performing devices, the V-OC is substantially lower than the QFLS. Using ultraviolet photoelectron spectroscopy and differential charging capacitance experiments we show that this is due to an energy level mis-alignment at the p-interface. The findings are corroborated by rigorous device simulations which outline important considerations to maximize the V-OC. This work highlights that the challenge to suppress non-radiative recombination losses in perovskite cells on their way to the radiative limit lies in proper energy level alignment and in suppression of defect recombination at the interfaces. Y1 - 2019 U6 - https://doi.org/10.1039/c9ee02020a SN - 1754-5692 SN - 1754-5706 VL - 12 IS - 9 SP - 2778 EP - 2788 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Armin, Ardalan A1 - Philippa, Bronson A1 - Neher, Dieter T1 - The Role of Space Charge Effects on the Competition between Recombination and Extraction in Solar Cells with Low-Mobility Photoactive Layers JF - The journal of physical chemistry letters N2 - The competition between charge extraction and nongeminate recombination critically determines the current-voltage characteristics of organic solar cells (OSCs) and their fill factor. As a measure of this competition, several figures of merit (FOMs) have been put forward; however, the impact of space charge effects has been either neglected, or not specifically addressed. Here we revisit recently reported FOMs and discuss the role of space charge effects on the interplay between recombination and extraction. We find that space charge effects are the primary cause for the onset of recombination in so-called non-Langevin systems, which also depends on the slower carrier mobility and recombination coefficient. The conclusions are supported with numerical calculations and experimental results of 25 different donor/acceptor OSCs with different charge transport parameters, active layer thicknesses or composition ratios. The findings represent a conclusive understanding of bimolecular recombination for drift dominated photocurrents and allow one to minimize these losses for given device parameters. Y1 - 2016 U6 - https://doi.org/10.1021/acs.jpclett.6b02106 SN - 1948-7185 VL - 7 SP - 4716 EP - 4721 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Stiller, Burkhard A1 - Karageorgiev, Peter A1 - Geue, Thomas A1 - Morawetz, Knut A1 - Saphiannikova, Marina A1 - Mechau, Norman A1 - Neher, Dieter T1 - Optically induced mass transport studied by scanning near-field optical- and atomic force microscopy N2 - Some functionalised thin organic films show a very unusual property, namely the light induced material transport. This effect enables to generate three-dimensional structures on surfaces of azobenzene containing films only caused by special optical excitation. The physical mechanisms underlying this phenomenon have not yet been fully understood, and in addition, the dimensions of structures created in that way are macroscopic because of the optical techniques and the wavelength of the used light. In order to gain deeper insight into the physical fundamentals of this phenomenon and to open possibilities for applications it is necessary to create and study structures not only in a macroscopic but also in nanometer range. We first report about experiments to generate optically induced nano structures even down to 100 nm size. The optical stimulation was therefore made by a Scanning Near-field Optical Microscope (SNOM). Secondly, physical conditions inside optically generated surface relief gratings were studied by measuring mechanical properties with high lateral resolution via pulse force mode and force distance curves of an AFM Y1 - 2004 SN - 0204-3467 ER - TY - JOUR A1 - Steyrleuthner, Robert A1 - Schubert, Marcel A1 - Jaiser, Frank A1 - Blakesley, James C. A1 - Chen, Zhihua A1 - Facchetti, Antonio A1 - Neher, Dieter T1 - Bulk electron transport and charge injection in a high mobility n-type semiconducting polymer N2 - Bulk electron transport in a high mobility n-type polymer is studied by time-of-flight photocurrent measurements and electron-only devices. Bulk electron mobilities of similar to 5 x 10(-3) cm(2)/Vs are obtained. The analysis of the electron currents suggests the presence of an injection barrier for all conventionally used low workfunction cathodes. Y1 - 2010 UR - http://www3.interscience.wiley.com/cgi-bin/jhome/10008336 U6 - https://doi.org/10.1002/adma.201000232 SN - 0935-9648 ER - TY - JOUR A1 - Steyrleuthner, Robert A1 - Schubert, Marcel A1 - Howard, Ian A1 - Klaumünzer, Bastian A1 - Schilling, Kristian A1 - Chen, Zhihua A1 - Saalfrank, Peter A1 - Laquai, Frederic A1 - Facchetti, Antonio A1 - Neher, Dieter T1 - Aggregation in a high-mobility n-type low-bandgap copolymer with implications on semicrystalline morphology JF - Journal of the American Chemical Society N2 - We explore the photophysics of P(NDI2OD-T2), a high-mobility and air-stable n-type donor/acceptor polymer. Detailed steady-state UV-vis and photoluminescence (PL) measurements on solutions of P(NDI2OD-T2) reveal distinct signatures of aggregation. By performing quantum chemical calculations, we can assign these spectral features to unaggregated and stacked polymer chains. NMR measurements independently confirm the aggregation phenomena of P(NDI2OD-T2) in solution. The detailed analysis of the optical spectra shows that aggregation is a two-step process with different types of aggregates, which we confirm by time-dependent PL measurements. Analytical ultracentrifugation measurements suggest that aggregation takes place within the single polymer chain upon coiling. By transferring these results to thin P(NDI2OD-T2) films, we can conclude that film formation is mainly governed by the chain collapse, leading in general to a high aggregate content of similar to 45%. This process also inhibits the formation of amorphous and disordered P(NDI2OD-T2) films. Y1 - 2012 U6 - https://doi.org/10.1021/ja306844f SN - 0002-7863 VL - 134 IS - 44 SP - 18303 EP - 18317 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Steyrleuthner, Robert A1 - Di Pietro, Riccardo A1 - Collins, Brian A. A1 - Polzer, Frank A1 - Himmelberger, Scott A1 - Schubert, Marcel A1 - Chen, Zhihua A1 - Zhang, Shiming A1 - Salleo, Alberto A1 - Ade, Harald W. A1 - Facchetti, Antonio A1 - Neher, Dieter T1 - The Role of Regioregularity, Crystallinity, and Chain Orientation on Electron Transport in a High-Mobility n-Type Copolymer JF - Journal of the American Chemical Society Y1 - 2014 U6 - https://doi.org/10.1021/ja4118736 SN - 0002-7863 VL - 136 IS - 11 SP - 4245 EP - 4256 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Steyrleuthner, Robert A1 - Bange, Sebastian A1 - Neher, Dieter T1 - Reliable electron-only devices and electron transport in n-type polymers N2 - Current-voltage analysis of single-carrier transport is a popular method for the determination of charge carrier mobilities in organic semiconductors. Although in widespread use for the analysis of hole transport, only a few reports can be found where the method was applied to electron transport. Here, we summarize the experimental difficulties related to the metal electrode leakage currents and nonlinear differential resistance (NDR) effects and explain their origin. We present a modified preparation technique for the metal electrodes and show that it significantly increases the reliability of such measurements. It allows to produce test devices with low leakage currents and without NDR even for thin organic layers. Metal oxides were often discussed as a possible cause of NDR. Our measurements on forcibly oxidized metal electrodes demonstrate that oxide layers are not exclusively responsible for NDR effects. We present electron transport data for two electron-conducting polymers often applied in all-polymer solar cells for a large variety of layer thicknesses and temperatures. The results can be explained by established exponential trapping models. Y1 - 2009 UR - http://jap.aip.org/ U6 - https://doi.org/10.1063/1.3086307 SN - 0021-8979 ER - TY - JOUR A1 - Srikhirin, Toemsak A1 - Laschitsch, Alexander A1 - Neher, Dieter A1 - Johannsmann, Diethelm T1 - Light-induced softening of azobenzene dye-doped polymer films probed with quartz crystal resonators Y1 - 2000 ER - TY - JOUR A1 - Srikhirin, T. A1 - Cimrova, V. A1 - Schiewe, B. A1 - Tzolov, M. A1 - Hagen, R. A1 - Kostromine, S. A1 - Bieringer, Thomas A1 - Neher, Dieter T1 - An Investigation of the photoinduced changes of absoprtion of high-performance photoaddressable Polymers Y1 - 2002 ER -