TY - JOUR A1 - Stolterfoht, Martin A1 - Wolff, Christian Michael A1 - Marquez, Jose A. A1 - Zhang, Shanshan A1 - Hages, Charles J. A1 - Rothhardt, Daniel A1 - Albrecht, Steve A1 - Burn, Paul L. A1 - Meredith, Paul A1 - Unold, Thomas A1 - Neher, Dieter T1 - Visualization and suppression of interfacial recombination for high-efficiency large-area pin perovskite solar cells JF - Nature Energy N2 - The performance of perovskite solar cells is predominantly limited by non-radiative recombination, either through trap-assisted recombination in the absorber layer or via minority carrier recombination at the perovskite/transport layer interfaces. Here, we use transient and absolute photoluminescence imaging to visualize all non-radiative recombination pathways in planar pintype perovskite solar cells with undoped organic charge transport layers. We find significant quasi-Fermi-level splitting losses (135 meV) in the perovskite bulk, whereas interfacial recombination results in an additional free energy loss of 80 meV at each individual interface, which limits the open-circuit voltage (V-oc) of the complete cell to similar to 1.12 V. Inserting ultrathin interlayers between the perovskite and transport layers leads to a substantial reduction of these interfacial losses at both the p and n contacts. Using this knowledge and approach, we demonstrate reproducible dopant-free 1 cm(2) perovskite solar cells surpassing 20% efficiency (19.83% certified) with stabilized power output, a high V-oc (1.17 V) and record fill factor (>81%). KW - Energy science and technology KW - Solar cells Y1 - 2018 U6 - https://doi.org/10.1038/s41560-018-0219-8 SN - 2058-7546 VL - 3 IS - 10 SP - 847 EP - 854 PB - Nature Publ. Group CY - London ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Caprioglio, Pietro A1 - Wolff, Christian Michael A1 - Marquez, Jose A. A1 - Nordmann, Joleik A1 - Zhang, Shanshan A1 - Rothhardt, Daniel A1 - Hörmann, Ulrich A1 - Amir, Yohai A1 - Redinger, Alex A1 - Kegelmann, Lukas A1 - Zu, Fengshuo A1 - Albrecht, Steve A1 - Koch, Norbert A1 - Kirchartz, Thomas A1 - Saliba, Michael A1 - Unold, Thomas A1 - Neher, Dieter T1 - The impact of energy alignment and interfacial recombination on the internal and external open-circuit voltage of perovskite solar cells JF - Energy & environmental science N2 - Charge transport layers (CTLs) are key components of diffusion controlled perovskite solar cells, however, they can induce additional non-radiative recombination pathways which limit the open circuit voltage (V-OC) of the cell. In order to realize the full thermodynamic potential of the perovskite absorber, both the electron and hole transport layer (ETL/HTL) need to be as selective as possible. By measuring the photoluminescence yield of perovskite/CTL heterojunctions, we quantify the non-radiative interfacial recombination currents in pin- and nip-type cells including high efficiency devices (21.4%). Our study comprises a wide range of commonly used CTLs, including various hole-transporting polymers, spiro-OMeTAD, metal oxides and fullerenes. We find that all studied CTLs limit the V-OC by inducing an additional non-radiative recombination current that is in most cases substantially larger than the loss in the neat perovskite and that the least-selective interface sets the upper limit for the V-OC of the device. Importantly, the V-OC equals the internal quasi-Fermi level splitting (QFLS) in the absorber layer only in high efficiency cells, while in poor performing devices, the V-OC is substantially lower than the QFLS. Using ultraviolet photoelectron spectroscopy and differential charging capacitance experiments we show that this is due to an energy level mis-alignment at the p-interface. The findings are corroborated by rigorous device simulations which outline important considerations to maximize the V-OC. This work highlights that the challenge to suppress non-radiative recombination losses in perovskite cells on their way to the radiative limit lies in proper energy level alignment and in suppression of defect recombination at the interfaces. Y1 - 2019 U6 - https://doi.org/10.1039/c9ee02020a SN - 1754-5692 SN - 1754-5706 VL - 12 IS - 9 SP - 2778 EP - 2788 PB - Royal Society of Chemistry CY - Cambridge ER - TY - JOUR A1 - Albrecht, Steve A1 - Tumbleston, John R. A1 - Janietz, Silvia A1 - Dumsch, Ines A1 - Allard, Sybille A1 - Scherf, Ullrich A1 - Ade, Harald W. A1 - Neher, Dieter T1 - Quantifying charge extraction in organic solar cells: The case of fluorinated PCPDTBT JF - The journal of physical chemistry letters N2 - We introduce a new and simple method to quantify the effective extraction mobility in organic solar cells at low electric fields and charge carrier densities comparable to operation conditions under one sun illumination. By comparing steady-state carrier densities at constant illumination intensity and under open-circuit conditions, the gradient of the quasi-Fermi potential driving the current is estimated as a function of external bias and charge density. These properties are then related to the respective steady-state current to determine the effective extraction mobility. The new technique is applied to different derivatives of the well-known low-band-gap polymer PCPDTBT blended with PC70BM. We show that the slower average extraction due to lower mobility accounts for the moderate fill factor when solar cells are fabricated with mono- or difluorinated PCPDTBT. This lower extraction competes with improved generation and reduced nongeminate recombination, rendering the monofluorinated derivative the most efficient donor polymer. Y1 - 2014 U6 - https://doi.org/10.1021/jz500457b SN - 1948-7185 VL - 5 IS - 7 SP - 1131 EP - 1138 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Kurpiers, Jona A1 - Ferron, Thomas A1 - Roland, Steffen A1 - Jakoby, Marius A1 - Thiede, Tobias A1 - Jaiser, Frank A1 - Albrecht, Steve A1 - Janietz, Silvia A1 - Collins, Brian A. A1 - Howard, Ian A. A1 - Neher, Dieter T1 - Probing the pathways of free charge generation in organic bulk heterojunction solar cells JF - Nature Communications N2 - The fact that organic solar cells perform efficiently despite the low dielectric constant of most photoactive blends initiated a long-standing debate regarding the dominant pathways of free charge formation. Here, we address this issue through the accurate measurement of the activation energy for free charge photogeneration over a wide range of photon energy, using the method of time-delayed collection field. For our prototypical low bandgap polymer:fullerene blends, we find that neither the temperature nor the field dependence of free charge generation depend on the excitation energy, ruling out an appreciable contribution to free charge generation though hot carrier pathways. On the other hand, activation energies are on the order of the room temperature thermal energy for all studied blends. We conclude that charge generation in such devices proceeds through thermalized charge transfer states, and that thermal energy is sufficient to separate most of these states into free charges. Y1 - 2018 U6 - https://doi.org/10.1038/s41467-018-04386-3 SN - 2041-1723 VL - 9 PB - Nature Publ. Group CY - London ER - TY - JOUR A1 - Proctor, Christopher M. A1 - Albrecht, Steve A1 - Kuik, Martijn A1 - Neher, Dieter A1 - Thuc-Quyen Nguyen, T1 - Overcoming geminate recombination and enhancing extraction in solution-processed small molecule solar cells JF - dvanced energy materials Y1 - 2014 U6 - https://doi.org/10.1002/aenm.201400230 SN - 1614-6832 SN - 1614-6840 VL - 4 IS - 10 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Caprioglio, Pietro A1 - Stolterfoht, Martin A1 - Wolff, Christian Michael A1 - Unold, Thomas A1 - Rech, Bernd A1 - Albrecht, Steve A1 - Neher, Dieter T1 - On the relation between the open-circuit voltage and quasi-fermi level splitting in efficient perovskite solar cells JF - advanced energy materials N2 - Today's perovskite solar cells (PSCs) are limited mainly by their open‐circuit voltage (VOC) due to nonradiative recombination. Therefore, a comprehensive understanding of the relevant recombination pathways is needed. Here, intensity‐dependent measurements of the quasi‐Fermi level splitting (QFLS) and of the VOC on the very same devices, including pin‐type PSCs with efficiencies above 20%, are performed. It is found that the QFLS in the perovskite lies significantly below its radiative limit for all intensities but also that the VOC is generally lower than the QFLS, violating one main assumption of the Shockley‐Queisser theory. This has far‐reaching implications for the applicability of some well‐established techniques, which use the VOC as a measure of the carrier densities in the absorber. By performing drift‐diffusion simulations, the intensity dependence of the QFLS, the QFLS‐VOC offset and the ideality factor are consistently explained by trap‐assisted recombination and energetic misalignment at the interfaces. Additionally, it is found that the saturation of the VOC at high intensities is caused by insufficient contact selectivity while heating effects are of minor importance. It is concluded that the analysis of the VOC does not provide reliable conclusions of the recombination pathways and that the knowledge of the QFLS‐VOC relation is of great importance. KW - electro-optical materials KW - perovskite solar cells KW - photovoltaic devices KW - thin films Y1 - 2019 U6 - https://doi.org/10.1002/aenm.201901631 SN - 1614-6832 SN - 1614-6840 VL - 9 IS - 33 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Albrecht, Steve A1 - Schindler, Wolfram A1 - Kurpiers, Jona A1 - Kniepert, Juliane A1 - Blakesley, James C. A1 - Dumsch, Ines A1 - Allard, Sybille A1 - Fostiropoulos, Konstantinos A1 - Scherf, Ullrich A1 - Neher, Dieter T1 - On the field dependence of free charge carrier generation and recombination in blends of PCPDTBT/PC70BM influence of solvent additives JF - The journal of physical chemistry letters N2 - We have applied time-delayed collection field (TDCF) and charge extraction by linearly increasing voltage (CELIV) to investigate the photogeneration, transport, and recombination of charge carriers in blends composed of PCPDTBT/PC70BM processed with and without the solvent additive diiodooctane. The results suggest that the solvent additive has severe impacts on the elementary processes involved in the photon to collected electron conversion in these blends. First, a pronounced field dependence of the free carrier generation is found for both blends, where the field dependence is stronger without the additive. Second, the fate of charge carriers in both blends can be described with a rather high bimolecular recombination coefficients, which increase with decreasing internal field. Third, the mobility is three to four times higher with the additive. Both blends show a negative field dependence of mobility, which we suggest to cause bias-dependent recombination coefficients. Y1 - 2012 U6 - https://doi.org/10.1021/jz3000849 SN - 1948-7185 VL - 3 IS - 5 SP - 640 EP - 645 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Albrecht, Steve A1 - Vandewal, Koen A1 - Tumbleston, John R. A1 - Fischer, Florian S. U. A1 - Douglas, Jessica D. A1 - Frechet, Jean M. J. A1 - Ludwigs, Sabine A1 - Ade, Harald W. A1 - Salleo, Alberto A1 - Neher, Dieter T1 - On the efficiency of charge transfer state splitting in polymer: Fullerene solar cells JF - Advanced materials KW - organic solar cells KW - charge generation KW - geminate recombination KW - charge transfer states KW - driving force KW - excess energy KW - morphology KW - spectroelectrochemistry Y1 - 2014 U6 - https://doi.org/10.1002/adma.201305283 SN - 0935-9648 SN - 1521-4095 VL - 26 IS - 16 SP - 2533 EP - 2539 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Tockhorn, Philipp A1 - Sutter, Johannes A1 - Cruz Bournazou, Alexandros A1 - Wagner, Philipp A1 - Jäger, Klaus A1 - Yoo, Danbi A1 - Lang, Felix A1 - Grischek, Max A1 - Li, Bor A1 - Li, Jinzhao A1 - Shargaieva, Oleksandra A1 - Unger, Eva A1 - Al-Ashouri, Amran A1 - Köhnen, Eike A1 - Stolterfoht, Martin A1 - Neher, Dieter A1 - Schlatmann, Rutger A1 - Rech, Bernd A1 - Stannowski, Bernd A1 - Albrecht, Steve A1 - Becker, Christiane T1 - Nano-optical designs for high-efficiency monolithic perovskite-silicon tandem solar cells JF - Nature nanotechnology N2 - Designing gentle sinusoidal nanotextures enables the realization of high-efficiency perovskite-silicon solar cells
Perovskite-silicon tandem solar cells offer the possibility of overcoming the power conversion efficiency limit of conventional silicon solar cells. Various textured tandem devices have been presented aiming at improved optical performance, but optimizing film growth on surface-textured wafers remains challenging. Here we present perovskite-silicon tandem solar cells with periodic nanotextures that offer various advantages without compromising the material quality of solution-processed perovskite layers. We show a reduction in reflection losses in comparison to planar tandems, with the new devices being less sensitive to deviations from optimum layer thicknesses. The nanotextures also enable a greatly increased fabrication yield from 50% to 95%. Moreover, the open-circuit voltage is improved by 15 mV due to the enhanced optoelectronic properties of the perovskite top cell. Our optically advanced rear reflector with a dielectric buffer layer results in reduced parasitic absorption at near-infrared wavelengths. As a result, we demonstrate a certified power conversion efficiency of 29.80%. Y1 - 2022 U6 - https://doi.org/10.1038/s41565-022-01228-8 SN - 1748-3387 SN - 1748-3395 VL - 17 IS - 11 SP - 1214 EP - 1221 PB - Nature Publishing Group CY - London [u.a.] ER - TY - JOUR A1 - Kegelmann, Lukas A1 - Tockhorn, Philipp A1 - Wolff, Christian Michael A1 - Márquez, José A. A1 - Caicedo Dávila, Sebastián A1 - Korte, Lars A1 - Unold, Thomas A1 - Loevenich, Wilfried A1 - Neher, Dieter A1 - Rech, Bernd A1 - Albrecht, Steve T1 - Mixtures of Dopant-Free Spiro-OMeTAD and Water-Free PEDOT as a Passivating Hole Contact in Perovskite Solar Cells JF - ACS applied materials & interfaces N2 - Doped spiro-OMeTAD at present is the most commonly used hole transport material (HTM) in n-i-p-type perovskite solar cells, enabling high efficiencies around 22%. However, the required dopants were shown to induce nonradiative recombination of charge carriers and foster degradation of the solar cell. Here, in a novel approach, highly conductive and inexpensive water-free poly(3,4-ethylenedioxythiophene) (PEDOT) is used to replace these dopants. The resulting spiro-OMeTAD/PEDOT (SpiDOT) mixed films achieve higher lateral conductivities than layers of doped spiro-OMeTAD. Furthermore, combined transient and steady-state photoluminescence studies reveal a passivating effect of PEDOT, suppressing nonradiative recombination losses at the perovskite/HTM interface. This enables excellent quasi-Fermi level splitting values of up to 1.24 eV in perovskite/SpiDOT layer stacks and high open-circuit voltages (V-OC) up to 1.19 V in complete solar cells. Increasing the amount of dopant-free spiro-OMeTAD in SpiDOT layers is shown to enhance hole extraction and thereby improves the fill factor in solar cells. As a consequence, stabilized efficiencies up to 18.7% are realized, exceeding cells with doped spiro-OMeTAD as a HTM in this study. Moreover, to the best of our knowledge, these results mark the lowest nonradiative recombination loss in the V-OC (140 mV with respect to the Shockley-Queisser limit) and highest efficiency reported so far for perovskite solar cells using PEDOT as a HTM. KW - perovskite solar cell KW - selective contact KW - spiro-OMeTAD KW - PEDOT KW - recombination KW - passivation KW - quasi-Fermi level splitting Y1 - 2019 U6 - https://doi.org/10.1021/acsami.9b01332 SN - 1944-8244 SN - 1944-8252 VL - 11 IS - 9 SP - 9172 EP - 9181 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Albrecht, Steve A1 - Schaefer, Sebastian A1 - Lange, Ilja A1 - Yilmaz, Seyfullah A1 - Dumsch, Ines A1 - Allard, Sybille A1 - Scherf, Ullrich A1 - Hertwig, Andreas A1 - Neher, Dieter T1 - Light management in PCPDTBT:PC70BM solar cells: A comparison of standard and inverted device structures JF - Organic electronics : physics, materials and applications N2 - We compare standard and inverted bulk heterojunction solar cells composed of PCPDTBT:PC70BM blends. Inverted devices comprising 100 nm thick active layers exhibited short circuit currents of 15 mA/cm(2), 10% larger than in corresponding standard devices. Modeling of the optical field distribution in the different device stacks proved that this enhancement originates from an increased absorption of incident light in the active layer. Internal quantum efficiencies (IQEs) were obtained from the direct comparison of experimentally derived and modeled currents for different layer thicknesses, yielding IQEs of similar to 70% for a layer thickness of 100 nm. Simulations predict a significant increase of the light harvesting efficiency upon increasing the layer thickness to 270 nm. However, a continuous deterioration of the photovoltaic properties with layer thickness was measured for both device architectures, attributed to incomplete charge extraction. On the other hand, our optical modeling suggests that inverted devices based on PCPDTBT should be able to deliver high power conversion efficiencies (PCEs) of more than 7% provided that recombination losses can be reduced. KW - Organic solar cells KW - Inverted solar cells KW - PCPDTBT KW - Low band-gap KW - Optical modeling Y1 - 2012 U6 - https://doi.org/10.1016/j.orgel.2011.12.019 SN - 1566-1199 VL - 13 IS - 4 SP - 615 EP - 622 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Kegelmann, Lukas A1 - Wolff, Christian Michael A1 - Awino, Celline A1 - Lang, Felix A1 - Unger, Eva L. A1 - Korte, Lars A1 - Dittrich, Thomas A1 - Neher, Dieter A1 - Rech, Bernd A1 - Albrecht, Steve T1 - It Takes Two to Tango-Double-Layer Selective Contacts in Perovskite Solar Cells for Improved Device Performance and Reduced Hysteresis JF - ACS applied materials & interfaces N2 - Solar cells made from inorganic organic perovskites have gradually approached market requirements as their efficiency and stability have improved tremendously in recent years. Planar low-temperature processed perovskite solar cells are advantageous for possible large-scale production but are more prone to exhibiting photocurrent hysteresis, especially in the regular n-i-p structure. Here, a systematic characterization of different electron selective contacts with a variety of chemical and electrical properties in planar n-i-p devices processed below 180 degrees C is presented. The inorganic metal oxides TiO2 and SnO2, the organic fullerene derivatives C-60, PCBM, and ICMA, as well as double-layers with a metal oxide/PCBM structure are used as electron transport materials (ETMs). Perovskite layers deposited atop, the different ETMs with the herein applied fabrication method show a similar morphology according to scanning electron microscopy. Further, surface photovoltage spectroscopy measurements indicate comparable perovskite absorber qualities on all ETMs, except TiO2, which shows a more prominent influence of defect states. Transient photoluminescence studies together with current voltage scans over a broad range of scan speeds reveal faster charge extraction, less pronounced hysteresis effects, and higher efficiencies for devices with fullerene compared to those with metal oxide ETMs. Beyond this, only double-layer ETM structures substantially diminish hysteresis effects for all performed scan speeds and strongly enhance the power conversion efficiency up to a champion stabilized value of 18.0%. The results indicate reduced recombination losses for a double-layer TiO2/PCBM contact design: First, a reduction of shunt paths through the fullerene to the ITO layer. Second, an improved hole blocking by the wide band gap metal oxide. Third, decreased transport losses due to an energetically more favorable contact, as implied by photoelectron spectroscopy measurements. The herein demonstrated improvements of multilayer selective contacts may serve as a general design guideline for perovskite solar cells. KW - perovskite solar cell KW - electron contact KW - double-layer KW - regular planar architecture KW - hysteresis KW - fullerene KW - metal oxide Y1 - 2017 U6 - https://doi.org/10.1021/acsami.7b00900 SN - 1944-8244 VL - 9 SP - 17246 EP - 17256 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Pradhan, Basudev A1 - Albrecht, Steve A1 - Stiller, Burkhard A1 - Neher, Dieter T1 - Inverted organic solar cells comprising low-temperature-processed ZnO films JF - Applied physics : A, Materials science & processing N2 - Inverted organic solar cells are fabricated using low-temperature-annealed ZnO film as an electron transport layer. Uniform ZnO films were prepared by spin coating a diethylzinc (DEZ) precursor solution in air, followed by annealing at 100 A degrees C. Organic solar cells prepared on these ZnO films with a 1:1 P3HT:PCBM blend as the active layer show a high power conversion efficiency of 4.03 %, which is more than 10 % higher than the PCE of solar cells comprising ZnO prepared via a high-temperature sol-gel route. Y1 - 2014 U6 - https://doi.org/10.1007/s00339-014-8373-8 SN - 0947-8396 SN - 1432-0630 VL - 115 IS - 2 SP - 365 EP - 369 PB - Springer CY - New York ER - TY - JOUR A1 - Schattauer, Sylvia A1 - Reinhold, Beate A1 - Albrecht, Steve A1 - Fahrenson, Christoph A1 - Schubert, Marcel A1 - Janietz, Silvia A1 - Neher, Dieter T1 - Influence of sintering on the structural and electronic properties of TiO2 nanoporous layers prepared via a non-sol-gel approach JF - Colloid and polymer science : official journal of the Kolloid-Gesellschaft N2 - In this work, a nonaqueous method is used to fabricate thin TiO2 layers. In contrast to the common aqueous sol-gel approach, our method yields layers of anatase nanocrystallites already at low temperature. Raman spectroscopy, electron microscopy and charge extraction by linearly increasing voltage are employed to study the effect of sintering temperature on the structural and electronic properties of the nanocrystalline TiO2 layer. Raising the sintering temperature from 120 to 600 A degrees C is found to alter the chemical composition, the layer's porosity and its surface but not the crystal phase. The room temperature mobility increases from 2 x 10(-6) to 3 x 10(-5) cm(2)/Vs when the sinter temperature is increased from 400 to 600 A degrees C, which is explained by a better interparticle connectivity. Solar cells comprising such nanoporous TiO2 layers and a soluble derivative of cyclohexylamino-poly(p-phenylene vinylene) were fabricated and studied with regard to their structural and photovoltaic properties. We found only weak polymer infiltration into the oxide layer for sintering temperatures up to 550 A degrees C, while the polymer penetrated deeply into titania layers that were sintered at 600 A degrees C. Best photovoltaic performance was reached with a nanoporous TiO2 film sintered at 550 A degrees C, which yielded a power conversion efficiency of 0.5 %. Noticeably, samples with the TiO2 layer dried at 120 A degrees C displayed short-circuit currents and open circuit voltages only about 15-20 % lower than for the most efficient devices, meaning that our nonaqueous route yields titania layers with reasonable transport properties even at low sintering temperatures. KW - Nonaqueous sol-gel KW - Thin nanocrystalline TiO2 layer KW - Solar cells KW - Effect of sintering KW - Linearly increasing voltage (CELIV) KW - Polymer infiltration KW - Transport properties titania KW - Transient fluorescence Y1 - 2012 U6 - https://doi.org/10.1007/s00396-012-2708-9 SN - 0303-402X VL - 290 IS - 18 SP - 1843 EP - 1854 PB - Springer CY - New York ER - TY - JOUR A1 - Würfel, Uli A1 - Neher, Dieter A1 - Spies, Annika A1 - Albrecht, Steve T1 - Impact of charge transport on current-voltage characteristics and power-conversion efficiency of organic solar cells JF - Nature Communications N2 - This work elucidates the impact of charge transport on the photovoltaic properties of organic solar cells. Here we show that the analysis of current-voltage curves of organic solar cells under illumination with the Shockley equation results in values for ideality factor, photo-current and parallel resistance, which lack physical meaning. Drift-diffusion simulations for a wide range of charge-carrier mobilities and illumination intensities reveal significant carrier accumulation caused by poor transport properties, which is not included in the Shockley equation. As a consequence, the separation of the quasi Fermi levels in the organic photoactive layer (internal voltage) differs substantially from the external voltage for almost all conditions. We present a new analytical model, which considers carrier transport explicitly. The model shows excellent agreement with full drift-diffusion simulations over a wide range of mobilities and illumination intensities, making it suitable for realistic efficiency predictions for organic solar cells. Y1 - 2015 U6 - https://doi.org/10.1038/ncomms7951 SN - 2041-1723 VL - 6 PB - Nature Publ. Group CY - London ER - TY - JOUR A1 - Roland, Steffen A1 - Neubert, Sebastian A1 - Albrecht, Steve A1 - Stannowski, Bernd A1 - Seger, Mark A1 - Facchetti, Antonio A1 - Schlatmann, Rutger A1 - Rech, Bernd A1 - Neher, Dieter T1 - Hybrid Organic/Inorganic Thin-Film Multijunction Solar Cells Exceeding 11% Power Conversion Efficiency JF - Advanced materials N2 - Hybrid multijunction solar cells comprising hydrogenated amorphous silicon and an organic bulk heterojunction are presented, reaching 11.7% power conversion efficiency. The benefits of merging inorganic and organic subcells are pointed out, the optimization of the cells, including optical modeling predictions and tuning of the recombination contact are described, and an outlook of this technique is given. Y1 - 2015 U6 - https://doi.org/10.1002/adma.201404698 SN - 0935-9648 SN - 1521-4095 VL - 27 IS - 7 SP - 1262 EP - 1267 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Stolterfoht, Martin A1 - Grischek, Max A1 - Caprioglio, Pietro A1 - Wolff, Christian Michael A1 - Gutierrez-Partida, Emilio A1 - Peña-Camargo, Francisco A1 - Rothhardt, Daniel A1 - Zhang, Shanshan A1 - Raoufi, Meysam A1 - Wolansky, Jakob A1 - Abdi-Jalebi, Mojtaba A1 - Stranks, Samuel D. A1 - Albrecht, Steve A1 - Kirchartz, Thomas A1 - Neher, Dieter T1 - How to quantify the efficiency potential of neat perovskite films BT - Perovskite semiconductors with an implied efficiency exceeding 28% JF - Advanced Materials N2 - Perovskite photovoltaic (PV) cells have demonstrated power conversion efficiencies (PCE) that are close to those of monocrystalline silicon cells; however, in contrast to silicon PV, perovskites are not limited by Auger recombination under 1-sun illumination. Nevertheless, compared to GaAs and monocrystalline silicon PV, perovskite cells have significantly lower fill factors due to a combination of resistive and non-radiative recombination losses. This necessitates a deeper understanding of the underlying loss mechanisms and in particular the ideality factor of the cell. By measuring the intensity dependence of the external open-circuit voltage and the internal quasi-Fermi level splitting (QFLS), the transport resistance-free efficiency of the complete cell as well as the efficiency potential of any neat perovskite film with or without attached transport layers are quantified. Moreover, intensity-dependent QFLS measurements on different perovskite compositions allows for disentangling of the impact of the interfaces and the perovskite surface on the non-radiative fill factor and open-circuit voltage loss. It is found that potassium-passivated triple cation perovskite films stand out by their exceptionally high implied PCEs > 28%, which could be achieved with ideal transport layers. Finally, strategies are presented to reduce both the ideality factor and transport losses to push the efficiency to the thermodynamic limit. KW - non-radiative interface recombination KW - perovskite solar cells KW - photoluminescence Y1 - 2020 U6 - https://doi.org/10.1002/adma.202000080 SN - 0935-9648 SN - 1521-4095 VL - 32 IS - 17 SP - 1 EP - 10 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Saliba, Michael A1 - Correa-Baena, Juan-Pablo A1 - Wolff, Christian Michael A1 - Stolterfoht, Martin A1 - Phung, Thi Thuy Nga A1 - Albrecht, Steve A1 - Neher, Dieter A1 - Abate, Antonio T1 - How to Make over 20% Efficient Perovskite Solar Cells in Regular (n-i-p) and Inverted (p-i-n) Architectures JF - Chemistry of materials : a publication of the American Chemical Society N2 - Perovskite solar cells (PSCs) are currently one of the most promising photovoltaic technologies for highly efficient and cost-effective solar energy production. In only a few years, an unprecedented progression of preparation procedures and material compositions delivered lab-scale devices that have now reached record power conversion efficiencies (PCEs) higher than 20%, competing with most established solar cell materials such as silicon, CIGS, and CdTe. However, despite a large number of researchers currently involved in this topic, only a few groups in the world can reproduce >20% efficiencies on a regular n-i-p architecture. In this work, we present detailed protocols for preparing PSCs in regular (n-i-p) and inverted (p-i-n) architectures with >= 20% PCE. We aim to provide a comprehensive, reproducible description of our device fabrication , protocols. We encourage the practice of reporting detailed and transparent protocols that can be more easily reproduced by other laboratories. A better reporting standard may, in turn, accelerate the development of perovskite solar cells and related research fields. Y1 - 2018 U6 - https://doi.org/10.1021/acs.chemmater.8b00136 SN - 0897-4756 SN - 1520-5002 VL - 30 IS - 13 SP - 4193 EP - 4201 PB - American Chemical Society CY - Washington ER - TY - JOUR A1 - Fischer, Florian S. U. A1 - Trefz, Daniel A1 - Back, Justus A1 - Kayunkid, Navaphun A1 - Tornow, Benjamin A1 - Albrecht, Steve A1 - Yager, Kevin G. A1 - Singh, Gurpreet A1 - Karim, Alamgir A1 - Neher, Dieter A1 - Brinkmann, Martin A1 - Ludwigs, Sabine T1 - Highly Crystalline Films of PCPDTBT with Branched Side Chains by Solvent Vapor Crystallization: Influence on Opto-Electronic Properties JF - Advanced materials N2 - PCPDTBT, a marginally crystallizable polymer, is crystallized into a new crystal structure using solvent-vapor annealing. Highly ordered areas with three different polymer-chain orientations are identified using TEM/ED, GIWAXS, and polarized Raman spectroscopy. The optical and structural properties differ significantly from films prepared by standard device preparation protocols. Bilayer solar cells, however, show similar performance. Y1 - 2015 U6 - https://doi.org/10.1002/adma.201403475 SN - 0935-9648 SN - 1521-4095 VL - 27 IS - 7 SP - 1223 EP - 1228 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Caprioglio, Pietro A1 - Zu, Fengshuo A1 - Wolff, Christian Michael A1 - Prieto, Jose A. Marquez A1 - Stolterfoht, Martin A1 - Becker, Pascal A1 - Koch, Norbert A1 - Unold, Thomas A1 - Rech, Bernd A1 - Albrecht, Steve A1 - Neher, Dieter T1 - High open circuit voltages in pin-type perovskite solar cells through strontium addition JF - Sustainable Energy & Fuels N2 - The incorporation of even small amounts of strontium (Sr) into lead-base hybrid quadruple cation perovskite solar cells results in a systematic increase of the open circuit voltage (V-oc) in pin-type perovskite solar cells. We demonstrate via absolute and transient photoluminescence (PL) experiments how the incorporation of Sr significantly reduces the non-radiative recombination losses in the neat perovskite layer. We show that Sr segregates at the perovskite surface, where it induces important changes of morphology and energetics. Notably, the Sr-enriched surface exhibits a wider band gap and a more n-type character, accompanied with significantly stronger surface band bending. As a result, we observe a significant increase of the quasi-Fermi level splitting in the neat perovskite by reduced surface recombination and more importantly, a strong reduction of losses attributed to non-radiative recombination at the interface to the C-60 electron-transporting layer. The resulting solar cells exhibited a V-oc of 1.18 V, which could be further improved to nearly 1.23 V through addition of a thin polymer interlayer, reducing the non-radiative voltage loss to only 110 meV. Our work shows that simply adding a small amount of Sr to the precursor solutions induces a beneficial surface modification in the perovskite, without requiring any post treatment, resulting in high efficiency solar cells with power conversion efficiency (PCE) up to 20.3%. Our results demonstrate very high V-oc values and efficiencies in Sr-containing quadruple cation perovskite pin-type solar cells and highlight the imperative importance of addressing and minimizing the recombination losses at the interface between perovskite and charge transporting layer. Y1 - 2019 U6 - https://doi.org/10.1039/c8se00509e SN - 2398-4902 VL - 3 IS - 2 SP - 550 EP - 563 PB - Royal Society of Chemistry CY - Cambridge ER -