TY  - JOUR
A1  - Kapernaum, Nadia
A1  - Lange, Alyna
A1  - Ebert, Max
A1  - Grunwald, Marco A.
A1  - Häge, Christian
A1  - Marino, Sebastian
A1  - Zens, Anna
A1  - Taubert, Andreas
A1  - Gießelmann, Frank
A1  - Laschat, Sabine
T1  - Current topics in ionic liquid crystals
JF  - ChemPlusChem
N2  - Ionic liquid crystals (ILCs), that is, ionic liquids exhibiting mesomorphism, liquid crystalline phases, and anisotropic properties, have received intense attention in the past years. Among others, this is due to their special properties arising from the combination of properties stemming from ionic liquids and from liquid crystalline arrangements. Besides interesting fundamental aspects, ILCs have been claimed to have tremendous application potential that again arises from the combination of properties and architectures that are not accessible otherwise, or at least not accessible easily by other strategies. The current review highlights recent developments in ILC research, starting with some key fundamental aspects. Further subjects covered include the synthesis and variations of modern ILCs, including the specific tuning of their mesomorphic behavior. The review concludes with reflections on some applications that may be within reach for ILCs and finally highlights a few key challenges that must be overcome prior and during true commercialization of ILCs.
KW  - electrochemistry
KW  - ionic liquid crystals
KW  - mesogen mesophases
KW  - self-assembly
KW  - X-ray diffraction
Y1  - 2021
U6  - https://doi.org/10.1002/cplu.202100397
SN  - 2192-6506
VL  - 87
IS  - 1
PB  - Wiley-VCH
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Wojnarowska, Zaneta
A1  - Lange, Alyna
A1  - Taubert, Andreas
A1  - Paluch, Marian
T1  - Ion and proton transport in aqueous/nonaqueous acidic tonic liquids for fuel-cell applications-insight from high-pressure dielectric studies
JF  - ACS applied materials & interfaces / American Chemical Society
N2  - The use of acidic ionic liquids and solids as electrolytes in fuel cells is an emerging field due to their efficient proton conductivity and good thermal stability. Despite multiple reports describing conducting properties of acidic ILs, little is known on the charge-transport mechanism in the vicinity of liquid-glass transition and the structural factors governing the proton hopping. To address these issues, we studied two acidic imidazolium-based ILs with the same cation, however, different anions-bulk tosylate vs small methanesulfonate. High-pressure dielectric studies of anhydrous and water-saturated materials performed in the close vicinity of T-g have revealed significant differences in the charge-transport mechanism in these two systems being undetectable at ambient conditions. Thereby, we demonstrated the effect of molecular architecture on proton hopping, being crucial in the potential electrochemical applications of acidic ILs.
KW  - proton hopping
KW  - dielectric spectroscopy
KW  - high pressure
KW  - ion transport
KW  - acidic ionic liquids
Y1  - 2021
U6  - https://doi.org/10.1021/acsami.1c06260
SN  - 1944-8244
SN  - 1944-8252
VL  - 13
IS  - 26
SP  - 30614
EP  - 30624
PB  - American Chemical Society
CY  - Washington
ER  - 
TY  - JOUR
A1  - Zehbe, Kerstin
A1  - Lange, Alyna
A1  - Taubert, Andreas
T1  - Stereolithography Provides Access to 3D Printed lonogels with High Ionic Conductivity
JF  - Energy Fuels
N2  - New ionogels (IGs) were prepared by combination of a series of sulfonate-based ionic liquids (ILs), 1-methyl-3-(4-sulfobutyl)imidazolium para-toluenesulfonate [BmimSO(3)][pTS], 1-methyl-1-butylpiperidiniumsulfonate para-toluenesul-fonate [BmpipSO(3)] [pTS], and 1-methyl-3-(4-sulfobutyl) imidazolium methylsulfonate [BmimSO(3)H][MeSO3] with a commercial stereolithography photoreactive resin. The article describes both the fundamental properties of the ILs and the resulting IGs. The IGs obtained from the ILs and the resin show high ionic conductivity of up to ca. 0.7.10(-4) S/cm at room temperature and 3.4-10(-3) S/cm at 90 degrees C. Moreover, the IGs are thermally stable to about 200 degrees C and mechanically robust. Finally, and most importantly, the article demonstrates that the IGs can be molded three-dimensionally using stereolithography. This provides, for the first time, access to IGs with complex 3D shapes with potential application in battery or fuel cell technology.
Y1  - 2019
U6  - https://doi.org/10.1021/acs.energyfuels.9b03379
SN  - 0887-0624
SN  - 1520-5029
VL  - 33
IS  - 12
SP  - 12885
EP  - 12893
PB  - American Chemical Society
CY  - Washington
ER  -