TY - THES A1 - Saretia, Shivam T1 - Modulating ultrathin films of semi-crystalline oligomers by Langmuir technique T1 - Modulation ultradünner Filme aus semikristalliner Oligomere durch Langmuir-Technik N2 - Polymeric films and coatings derived from semi-crystalline oligomers are of relevance for medical and pharmaceutical applications. In this context, the material surface is of particular importance, as it mediates the interaction with the biological system. Two dimensional (2D) systems and ultrathin films are used to model this interface. However, conventional techniques for their preparation, such as spin coating or dip coating, have disadvantages, since the morphology and chain packing of the generated films can only be controlled to a limited extent and adsorption on the substrate used affects the behavior of the films. Detaching and transferring the films prepared by such techniques requires additional sacrificial or supporting layers, and free-standing or self supporting domains are usually of very limited lateral extension. The aim of this thesis is to study and modulate crystallization, melting, degradation and chemical reactions in ultrathin films of oligo(ε-caprolactone)s (OCL)s with different end-groups under ambient conditions. Here, oligomeric ultrathin films are assembled at the air-water interface using the Langmuir technique. The water surface allows lateral movement and aggregation of the oligomers, which, unlike solid substrates, enables dynamic physical and chemical interaction of the molecules. Parameters like surface pressure (π), temperature and mean molecular area (MMA) allow controlled assembly and manipulation of oligomer molecules when using the Langmuir technique. The π-MMA isotherms, Brewster angle microscopy (BAM), and interfacial infrared spectroscopy assist in detecting morphological and physicochemical changes in the film. Ultrathin films can be easily transferred to the solid silicon surface via Langmuir Schaefer (LS) method (horizontal substrate dipping). Here, the films transferred on silicon are investigated using atomic force microscopy (AFM) and optical microscopy and are compared to the films on the water surface. The semi-crystalline morphology (lamellar thicknesses, crystal number densities, and lateral crystal dimensions) is tuned by the chemical structure of the OCL end-groups (hydroxy or methacrylate) and by the crystallization temperature (Tc; 12 or 21 °C) or MMAs. Compression to lower MMA of ~2 Å2, results in the formation of a highly crystalline film, which consists of tightly packed single crystals. Preparation of tightly packed single crystals on a cm2 scale is not possible by conventional techniques. Upon transfer to a solid surface, these films retain their crystalline morphology whereas amorphous films undergo dewetting. The melting temperature (Tm) of OCL single crystals at the water and the solid surface is found proportional to the inverse crystal thickness and is generally lower than the Tm of bulk PCL. The impact of OCL end-groups on melting behavior is most noticeable at the air-solid interface, where the methacrylate end-capped OCL (OCDME) melted at lower temperatures than the hydroxy end-capped OCL (OCDOL). When comparing the underlying substrate, melting/recrystallization of OCL ultrathin films is possible at lower temperatures at the air water interface than at the air-solid interface, where recrystallization is not visible. Recrystallization at the air-water interface usually occurs at a higher temperature than the initial Tc. Controlled degradation is crucial for the predictable performance of degradable polymeric biomaterials. Degradation of ultrathin films is carried out under acidic (pH ~ 1) or enzymatic catalysis (lipase from Pseudomonas cepcia) on the water surface or on a silicon surface as transferred films. A high crystallinity strongly reduces the hydrolytic but not the enzymatic degradation rate. As an influence of end-groups, the methacrylate end-capped linear oligomer, OCDME (~85 ± 2 % end-group functionalization) hydrolytically degrades faster than the hydroxy end capped linear oligomer, OCDOL (~95 ± 3 % end-group functionalization) at different temperatures. Differences in the acceleration of hydrolytic degradation of semi-crystalline films were observed upon complete melting, partial melting of the crystals, or by heating to temperatures close to Tm. Therefore, films of densely packed single crystals are suitable as barrier layers with thermally switchable degradation rates. Chemical modification in ultrathin films is an intricate process applicable to connect functionalized molecules, impart stability or create stimuli-sensitive cross-links. The reaction of end-groups is explored for transferred single crystals on a solid surface or amorphous monolayer at the air-water interface. Bulky methacrylate end-groups are expelled to the crystal surface during chain-folded crystallization. The density of end-groups is inversely proportional to molecular weight and hence very pronounced for oligomers. The methacrylate end-groups at the crystal surface, which are present at high concentration, can be used for further chemical functionalization. This is demonstrated by fluorescence microscopy after reaction with fluorescein dimethacrylate. The thermoswitching behavior (melting and recrystallization) of fluorescein functionalized single crystals shows the temperature-dependent distribution of the chemically linked fluorescein moieties, which are accumulated on the surfaces of crystals, and homogeneously dispersed when the crystals are molten. In amorphous monolayers at the air-water interface, reversible cross-linking of hydroxy-terminated oligo(ε-caprolactone) monolayers using dialdehyde (glyoxal) lead to the formation of 2D networks. Pronounced contraction in the area occurred for 2D OCL films in dependence of surface pressure and time indicating the reaction progress. Cross linking inhibited crystallization and retarded enzymatic degradation of the OCL film. Altering the subphase pH to ~2 led to cleavage of the covalent acetal cross-links. Besides as model systems, these reversibly cross-linked films are applicable for drug delivery systems or cell substrates modulating adhesion at biointerfaces. N2 - Ultradünne Filme/Beschichtungen aus semikristallinen oligomeren Makromolekülen sind für medizinische und pharmazeutische Anwendungen von Bedeutung. Dabei kommt der Materialoberfläche eine besondere Bedeutung zu, da diese die Interaktion mit dem umgebenden biologischen System ermöglicht. Zur Modellierung der Oberfläche werden 2D Systeme und ultradünne Filme verwendet. Herkömmlichen Techniken zu deren Präparation wie Spin-Coating oder Dip-Coating haben jedoch Nachteile, da sich die Morphologie und Kettenpackung der erzeugten Filme nur sehr bedingt kontrollieren lässt und sich die Adsorption auf dem verwendeten Substrat auf das Verhalten der Filme auswirkt. Zum Ablösen oder Übertragen der mit Hilfe dieser Techniken hergestellten Filme sind zusätzliche Opfer- oder Transferschichten erforderlich. Zudem können mit diesen Methoden nur freistehende oder selbsttragende Filme von sehr geringer lateraler Ausdehnung hergestellt werden. Das Ziel dieser Arbeit ist es, Kristallisation, Schmelzen, Abbau und chemische Reaktionen in ultradünnen Filmen von Oligo(ε-caprolacton)en (OCL)s mit unterschiedlichen Endgruppen unter Umgebungsbedingungen zu untersuchen und zu kontrollieren. Dazu wurden ultradünne Filme an der Luft-Wasser-Grenzfläche mit der Langmuir-Technik erzeugt. Die Wasseroberfläche erlaubt eine ungestörte Bewegung und Aggregation der Oligomere, was, im Gegensatz zu festen Substraten, dynamische physikalische und chemische Interaktion der Moleküle miteinander ermöglicht. Die Langmuir-Technik erlaubt mit Hilfe von Parametern wie Temperatur, Oberflächendruck (π) und Fläche pro Wiederholheinheit eine kontrollierte Manipulation der Oligomere. Kompressionsiothermen, Brewster-Winkelmikroskopie und Grenzflächen-Infrarotspektroskopie halfen beim Nachweis morphologischer und physikalisch-chemischer Veränderungen im Film. Die ultradünnen Filme wurden über das Langmuir-Schäfer-Verfahren (Kontakt mit Substrat in paralleler Orientierung zur Grenzfläche) auf Siliziumsubstrate übertragen. Danach wurden die übertragenen Filme mittels AFM und optischer Mikroskopie untersucht und mit Filmen an der Wasseroberfläche verglichen. Die teilkristalline Morphologie (Lamellendicke, Kristallzahldichte und laterale Dimension der Kristalle) von Polymerfilmen kann durch die chemische Struktur der OCL-Endgruppen (Hydroxy oder Methacrylat) und durch die Kristallisationstemperatur (Tc; 12 oder 21 °C) oder die Fläche pro Wiederholeinheit beeinflusst werden. Die Kompression auf eine sehr kleine Fläche pro Wiederholeinheit von ~2 Å2 führt zur Bildung eines hochkristallinen Films, der aus dicht gepackten Einkristallen besteht. Eine Synthese von derartigen Filmen im cm2 Maßstab ist mit herkömmlichen Techniken nicht möglich. Nach Übertragung auf eine feste Oberfläche behielten die teilkristallinen Filme ihre Morphologie, während amorphe Filme das für Polymere charakteristische Entnetzungsverhalten aufwiesen. Die Schmelztemperaturen (Tm) von OCL-Einkristallen an der Wasser- und Festkörperoberfläche waren proportional zur inversen Kristalldicke und im Allgemeinen niedriger als die Tm von PCL im Festkörper. Der Einfluss der OCL-Endgruppen auf das Schmelzverhalten war an der Luft-Feststoff-Grenzfläche am deutlichsten, wo OCL mit Methacrylat-Endgruppen bei niedrigeren Temperaturen schmolz als OCL mit Hydroxyl-Endgruppen. Das Schmelzen/Rekristallisieren ultradünner OCL-Filme an der Luft-Wasser-Grenzfläche erfolgte bei niedrigeren Temperaturen als an der Luft-Feststoff-Grenzfläche, wo keine Rekristallisation beobachtet wurde. Die Rekristallisation geschmolzener Filme an der Luft-Wasser-Grenzfläche erfolgte normalerweise bei einer höheren Temperatur als der anfänglichen Tc. Der kontrollierte Abbau ist entscheidend für die Performance von abbaubaren Polymeren als Biomaterialien. Der Abbau ultradünner Filme erfolgte hydrolytisch entweder unter saurer (pH ~ 1) oder enzymatischer Katalyse (Lipase aus Pseudomonas cepcia) auf der Wasseroberfläche oder als übertragene Filme auf Siliziumoberflächen. Eine hohe Kristallinität reduzierte die hydrolytische Abbaurate stark, aber die enzymatische dagegen wenig. Das lineare Oligomer mit Methacrylat Endgruppen (~85 ± 2 % Endgruppenfunktionalisierung) wurde bei unterschiedlichen Temperaturen schneller hydrolytisch abgebaut als das lineare Oligomer mit Hydroxyl Endgruppen (~95 ± 3 % Endgruppenfunktionalisierung). Unterschiede in der Beschleunigung des hydrolytischen Abbaus von teilkristallinen Filmen wurden beim vollständigen Schmelzen, teilweisen Schmelzen der Kristalle, oder durch erwärmen in die Nähe von Tm beobachtet. Daher eignen sich Filme aus dicht gepackten Einkristallen als Barriereschichten mit thermisch schaltbarer Degradationsrate. Chemische Reaktionen in ultradünnen Filmen können angewandt werden, um funktionalisierte Moleküle zu verbinden und ihnen Stabilität zu verleihen oder Stimuli-sensitive Vernetzungen zu erzeugen. Hier wurden die Reaktionen der Endgruppen transferierter Einkristalle auf festen Oberflächen und amorphen Monoschichten an der Luft-Wasser-Grenzfläche untersucht. Da die Kettenenden defekte in den Einkristallen darstellen würden, werden sie bei der Kristallisation an der Kristalloberfläche angeordnet. Die Dichte der Endgruppen ist umgekehrt proportional zum Molekulargewicht und daher bei Oligomeren besonders hoch. Hier wurden mit Methacrylatendgruppen versehene OCL Moleküle verwendet. Diese Gruppen können chemisch weiter umgesetzt und für eine Funktionalisierung der Kirstalle verwendet werden. Dies wurde fluoreszenz-mikroskopisch nach der Reaktion mit Fluoresceindimethacrylat nachgewiesen. Das thermische Schalten (Schmelzen und Umkristallisieren) von Fluorescein-funktionalisierten Einkristallen erzeugt eine temperaturabhängige Verteilung der chemisch verknüpften Fluorescein-Einheiten, die sich auf den Oberflächen der Kristalle ansammeln und beim Schmelzen der Kristalle homogen dispergiert werden. In amorphen Monoschichten an der Luft-Wasser-Grenzfläche führt die reversible Vernetzung von Hydroxy-terminierten Oligo(ε-caprolacton) Monoschichten unter Verwendung eines Dialdehyds (Glyoxal) zur Bildung von zweidimensionalen (2D) Netzwerken. Bei 2D-OCL-Filmen trat eine ausgeprägte Kontraktion der Fläche in Abhängigkeit von Oberflächendruck und Zeit auf, was den Fortschritt der Reaktion anzeigte. Die Vernetzung hemmte die Kristallisation und verzögerte den enzymatischen Abbau des OCL-Films. Eine Änderung des pH-Wertes der Subphase auf ~2 führte zur Spaltung der kovalenten Acetalvernetzungen. Außer als Modellsysteme wäre der Einsatz dieser reversibel vernetzten Filme für den Einsatz als Drug-Delivery-Systeme oder als Oberflächen zur Steuerung der Adhäsion von Zellen möglich. KW - polymer KW - poly(ε-caprolactone) KW - 2D material KW - ultrathin film KW - single crystals KW - crystallization KW - melting KW - degradation KW - hydrolysis KW - reactions KW - substrate KW - end-groups KW - hydroxy KW - methacrylate KW - Polymer KW - Poly(ε-caprolacton) KW - 2D-Material KW - Beschichtungen KW - Ultradünne Filme KW - Einkristalle KW - Kristallisation KW - Schmelz KW - Abbau KW - Hydrolyse KW - Reaktion KW - Substrat KW - Hydroxyl KW - Methacrylat Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-542108 ER - TY - JOUR A1 - Saretia, Shivam A1 - Machatschek, Rainhard Gabriel A1 - Schulz, Burkhard A1 - Lendlein, Andreas T1 - Reversible 2D networks of oligo(epsilon-caprolactone) at the air-water interface JF - Biomedical Materials N2 - Hydroxyl terminated oligo(epsilon-caprolactone) (OCL) monolayers were reversibly cross-linked forming two dimensional networks (2D) at the air-water interface. The equilibrium reaction with glyoxal as the cross-linker is pH-sensitive. Pronounced contraction in the area of the prepared 2DOCL films in dependence of surface pressure and time revealed the process of the reaction. Cross-linking inhibited crystallization and retarded enzymatic degradation of the OCLfilm. Altering the subphase pH led to a cleavage of the covalent acetal cross-links. The reversibility of the covalent acetal cross-links was proved by observing an identical isotherm as non-cross-linked sample. Besides as model systems, these customizable reversible OCL2D networks are intended for use as pHresponsive drug delivery systems or functionalized cell culture substrates. KW - poly(epsilon-caprolactone) KW - langmuir monolayer KW - two dimensional network KW - crystallization KW - cross-linking Y1 - 2019 U6 - https://doi.org/10.1088/1748-605X/ab0cef SN - 1748-6041 SN - 1748-605X VL - 14 IS - 3 PB - IOP Publ. Ltd. CY - Bristol ER - TY - JOUR A1 - Noack, Sebastian A1 - Schanzenbach, Dirk A1 - Koetz, Joachim A1 - Schlaad, Helmut T1 - Polylactide-based amphiphilic block copolymers BT - Crystallization-Induced Self-Assembly and Stereocomplexation JF - Macromolecular rapid communications N2 - The aqueous self-assembly behavior of a series of poly(ethylene glycol)-poly(l-/d-lactide) block copolymers and corresponding stereocomplexes is examined by differential scanning calorimetry, dynamic light scattering, and transmission electron microscopy. Block copolymers assemble into spherical micelles and worm-like aggregates at room temperature, whereby the fraction of the latter seemingly increases with decreasing lactide weight fraction or hydrophobicity. The formation of the worm-like aggregates arises from the crystallization of the polylactide by which the spherical micelles become colloidally unstable and fuse epitaxically with other micelles. The self-assembly behavior of the stereocomplex aggregates is found to be different from that of the block copolymers, resulting in rather irregular-shaped clusters of spherical micelles and pearl-necklace-like structures. KW - crystallization KW - polylactide KW - self-assembly KW - stereocomplexation Y1 - 2018 U6 - https://doi.org/10.1002/marc.201800639 SN - 1022-1336 SN - 1521-3927 VL - 40 IS - 1 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Thielke, Michael W. A1 - Secker, Christian A1 - Schlaad, Helmut A1 - Theato, Patrick T1 - Electrospinning of Crystallizable Polypeptoid Fibers JF - Macromolecular rapid communications N2 - A unique fabrication process of low molar mass, crystalline polypeptoid fibers is described. Thermoresponsive fiber mats are prepared by electrospinning a homogeneous blend of semicrystalline poly(N-(n-propyl) glycine) (PPGly; 4.1 kDa) with high molar mass poly(ethylene oxide) (PEO). Annealing of these fibers at approximate to 100 degrees C selectively removes the PEO and produces stable crystalline fiber mats of pure PPGly, which are insoluble in aqueous solution but can be redissolved in methanol or ethanol. The formation of water-stable polypeptoid fiber mats is an important step toward their utilization in biomedical applications such as tissue engineering or wound dressing. KW - biomaterials KW - crystallization KW - electrospinning KW - polypeptoids KW - thermoresponsive Y1 - 2016 U6 - https://doi.org/10.1002/marc.201500502 SN - 1022-1336 SN - 1521-3927 VL - 37 SP - 100 EP - 104 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Demirel, A. Levent A1 - Guner, Pinar Tatar A1 - Verbraeken, Bart A1 - Schlaad, Helmut A1 - Schubert, Ulrich S. A1 - Hoogenboom, Richard T1 - Revisiting the Crystallization of Poly(2-alkyl-2-oxazoline)s JF - Journal of polymer science : B, Polymer physics N2 - Poly(2-alkyl-2-oxazoline)s (PAOx) exhibit different crystallization behavior depending on the length of the alkyl side chain. PAOx having methyl, ethyl, or propyl side chains do not show any bulk crystallization. Crystallization in the heating cycle, that is, cold crystallization, is observed for PAOx with butyl and pentyl side chains. For PAOx with longer alkyl side chains crystallization occurs in the cooling cycle. The different crystallization behavior is attributed to the different polymer chain mobility in line with the glass transition temperature (T-g) dependency on alkyl side chain length. The decrease in chain mobility with decreasing alkyl side chain length hinders the relaxation of the polymer backbone to the thermodynamic equilibrium crystalline structure. Double melting behavior is observed for PButOx and PiPropOx which is explained by the melt-recrystallization mechanism. Isothermal crystallization experiments of PButOx between 60 and 90 degrees C and PiPropOx between 90 and 150 degrees C show that PAOx can crystallize in bulk when enough time is given. The decrease of Tg and the corresponding increase in chain mobility at T > T-g with increasing alkyl side chain length can be attributed to an increasing distance between the polymer backbones and thus decreasing average strength of amide dipole interactions. (C) 2015 Wiley Periodicals, Inc. KW - chain mobility KW - crystallization KW - differential scanning calorimetry (DSC) KW - effect of alkyl side chains KW - glass transition temperature KW - melt KW - melt-recrystallization KW - polymer crystallization Y1 - 2016 U6 - https://doi.org/10.1002/polb.23967 SN - 0887-6266 SN - 1099-0488 VL - 54 SP - 721 EP - 729 PB - Wiley-Blackwell CY - Hoboken ER - TY - JOUR A1 - Yan, Wan A1 - Fang, Liang A1 - Nöchel, Ulrich A1 - Kratz, Karl A1 - Lendlein, Andreas T1 - Influence of programming strain rates on the shape-memory performance of semicrystalline multiblock copolymers JF - Journal of polymer science : B, Polymer physics N2 - Multiblock copolymers named PCL-PIBMD consisting of crystallizable poly(epsilon-caprolactone) segments and crystallizable poly[oligo(3S-iso-butylmorpholine-2,5-dione)] segments coupled by trimethyl hexamethylene diisocyanate provide a versatile molecular architecture for achieving shape-memory effects (SMEs) in polymers. The mechanical properties as well as the SME performance of PCL-PIBMD can be tailored by the variation of physical parameters during programming such as deformation strain or applied temperature protocols. In this study, we explored the influence of applying different strain rates during programming on the resulting nanostructure of PCL-PIBMD. Programming was conducted at 50 degrees C by elongation to epsilon(m)=50% with strain rates of 1 or 10 or 50 mmmin(-1). The nanostructural changes were visualized by atomic force microscopy (AFM) measurements and investigated by in situ wide and small angle X-ray scattering experiments. With increasing the strain rate, a higher degree of orientation was observed in the amorphous domains. Simultaneously the strain-induced formation of new PIBMD crystals as well as the fragmentation of existing large PIBMD crystals occurred. The observed differences in shape fixity ratio and recovery stress of samples deformed with various strain rates can be attributed to their different nanostructures. The achieved findings can be relevant parameters for programming the shape-memory polymers with designed recovery forces. (c) 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 1935-1943 KW - atomic force microscopy (AFM) KW - crystal structures KW - crystallization KW - multiblock copolymer KW - stimuli-sensitive polymers KW - SAXS KW - shape-memory effect KW - WAXS KW - X-ray scattering Y1 - 2016 U6 - https://doi.org/10.1002/polb.24097 SN - 0887-6266 SN - 1099-0488 VL - 54 SP - 1935 EP - 1943 PB - Wiley-Blackwell CY - Hoboken ER - TY - THES A1 - Jiang, Yuan T1 - Precursor phases in non-classical crystallization N2 - The main objective of this thesis is to understand molecular crystallization as a multistep process with or without polymeric additives, including transient liquid-liquid phase separation, nanocrystal nucleation within the dense phase, and subsequent nanocrystal self-assembly or self-organization in sequence. The thesis starts with a quaternary model system, containing DL-Glutamic acid (Glu), polyethyleneimine (PEI), water, and EtOH, for the understanding of multistep precipitation of Glu with PEI as an additive. The experiments were performed by mixing Glu-PEI aqueous solution with a non-solvent EtOH. First, the phase diagram of the quaternary system is determined, obtaining precipitate, coacervates, or homogeneous mixtures by varying Glu/PEI w/w and water/EtOH v/v. Coacervation is observed to occur over a wide range of Glu/PEI with various volumes. The composition of coacervates is conveniently characterized by nuclear magnetic resonance spectroscopy. The observed coacervates are thermodynamically stable phases rich in solute, which is different from metastable polymer-induced liquid precursors. The combination of atomic force microscopy, small angle scattering, and ξ-potential measurements confirms the coexistence of monomers and Glu/PEI complexes and the aggregation of complexes in Glu-PEI-water systems. This suggests that there might be a direct structural transformation between the Glu-PEI complexes in aqueous solution and the metastable liquid precursors in a water-EtOH mixture. The multistep mechanism of Glu precipitation with PEI as an additive is investigated thereafter. The combination of stopped flow and small angle scattering demonstrates that the initially formed liquid precursors pass through an alteration of growth and coalescence. Combined with results from optical microscopy and scanning electron microscopy, the nucleation of nanoplatelets happens within each liquid precursor droplet, and nanoplatelets reorient themselves and self-organize into a radial orientation in the crystalline microspheres. The recipe was then extended to the precipitation of organics in other oppositely charged amino acid-polyelectrolyte systems. After the success in preparing hierarchical microspheres in solution, the similar recipe can be extended to the preparation of patterned thin films on substrate. By dipping a quaternary DL-Lys·HCl (Lys)–polyacrylic acid (PAA)–water–EtOH dispersion on a hydrophilic slide, the fast evaporation process of the volatile solvent EtOH is responsible for the homogeneous nucleation of NPs. Then, the following complete evaporation causes the mesocrystallization of a continuous spherulitic thin film along the receding line of the liquid, which again transforms into a mesocrystalline thin film. Furthermore, annealing is used to optimize the property of mesocrystalline thin films. As evaporation is a non-equilibrium process, it can be used to tune the kinetics of crystallization. Therefore, hierarchical or periodical thin films are obtainable by starting the evaporation from microspheres recrystallization, obtaining mesocrystalline thin films with 4 hierarchy levels. The results reveal that evaporation provides an easy but effective way for the formation of patterned structures via the positioning of NPs after their fast nucleation, resulting in different kinds of patterns by controlling the concentration of NPs, solvent evaporation rate, and other physical forces. Non-classical crystallization is not limited to crystallizations with polymeric additives. We also observed the nucleation and growth of a new molecular layer on the growing DL-Glu·H2O crystals from a supersaturated mother liquor by using an in-situ atomic force microscopy (AFM), where the nucleation and growth of a molecular layer proceed via amorphous nanoparticle (NP) attachment and relaxation process before the observation of the growth of a newly formed molecular layer. NP attachment to the crystal surface is too fast to observe by using in-situ AFM. The height shrinkage of NPs, combined to the structural transformation from 3D amorphous NPs to 2D crystalline layer, is observed during the relaxation process. The nucleation and growth of a newly formed molecular layer from NP relaxation is contradictory to the classical nucleation theory, which hypothesizes that nuclei show the same crystallographic properties as a bulk crystal. The formation of a molecular layer by NP attachment and relaxation rather than attachment of single molecules provides a different picture from the currently held classical nucleation and growth theory regarding the growth of single crystals from solution. N2 - Das Hauptziel dieser Arbeit ist das Verständnis der molekularen Kristallisation, sowohl mit als auch ohne polymere Additive, als einen mehrstufigen Prozess. Dieser beinhaltet eine transiente flüssig-flüssig Phasentrennung, die Nukleation von Nanokristallen in der dichten flüssigen Precursor-Phase so wie eine anschließende nanokristalline Selbstorganisation. Die Arbeit beginnt mit Untersuchungen an einem quaternären Modelsystem bestehend aus DL-Glutamat (Glu), Polyethylenimin (PEI), Wasser und Ethanol. Das Phasendiagramm dieses quaternären Systems wird durch Variation der Glu/PEI w/w und Wasser/EtOH v/v Verhältnisse bestimmt, wobei Präzpitat aus polymerinduzierten flüssigen Precursor, Koazervate oder homogene Mischungen erhalten werden Das thermodynamisch stabile Koazervat kann als Referenz für das Verständnis von flüssigen Precursorn angesehen werden, welche in der Natur metastabil und transient sind. Der mehrstufige Mechanismus der Glu-Präzipitation mit PEI als Additiv wird dann mittels Neutronen Kleinwinkelstreuung untersucht. Dies zeigt, dass die ursprünglich gebildeten flüssigen Precursor noch vor der Nukleation von Nanokristallen einen Wechsel von Wachstum und Koaleszenz durchlaufen. Die Ergebnisse aus optischer- und Eletronenmikroskopie zeigen, dass sowohl die flüssigen Precursor Superstrukturen ausbilden als auch, dass die Nukleation von Nanoplättchen in jedem einzelnen Precursor Tropfen von statten geht. Dies geschieht noch bevor sich die Nanoplättchen selbst in einer radialen Orientierung ausrichten. Diese Studie liefert die Kinetik der Präzipitation von organischen Stoffen in Gegenwart von polymeren Additiven. Eine ähnliche Vorgehensweise wie für die Herstellung von Mikrokügelchen kann für die Darstellung von gemusterten Filmen angewandt werden. Die homogene Nukleation von Nanopartikeln (NPs) findet während der Verdampfung einer quarternären DL-Lys·HCl-Polyacrylsäure-Wasser-Ethanol Dispersion auf einer hydrophilen Oberfläche statt. Die darauffolgende vollständige Verdampfung löst die Mesokristallisation eines kontinuierlichen sphärolithischen dünnen Films aus, welcher sich wiederum in einen mesokristallinen dünnen Film umwandelt. Mesokristalline Filme mit 4 Hierarchiestufen bzw. auch periodische Filme werden durch die Verdampfung der Mikrokügelchen-Dispersion erhalten. Die Ergebnisse zeigen, dass die Verdampfung eine einfache aber effektive Methode zur Herstellung von verschieden gemusterten hierarchischen Filmen darstellt. Nicht-klassische Kristallisation wird auch in der Abwesenheit von polymeren Additiven beobachtet. Wir verfolgen mittels Rasterkraftmikroskop (AFM) die Nukleation und das Wachstum einer neuen molekularen Schicht auf wachsenden DL-Glu·H2O Kristallen aus übersättigter Mutterlauge. Die Bildung einer neuen molekularen Schicht verläuft durch die Anlagerung von amorphen Nanopartikeln. Das Schrumpfen der NPs zusammen mit der strukturellen Änderung von dreidimensionalen NPs zu 2D Schichten wird während dieses Relaxationsprozesses beobachtet. Schließlich kommt es zu der Ausbildung einer neuen molekularen Schicht. Die Bildung einer molekularen Schicht durch die Anlagerung von Nanopartikeln aus der Lösung und die darauffolgende Relaxation liefert ein abweichendes Bild zu der bisher gängigen klassischen Theorie des Kristallwachstums. T2 - Vorstufenphasen in nichtklassischer Kristallisation KW - Mesokristall KW - Vorstufe KW - Kristallisation KW - mesocrystal KW - precursor KW - crystallization Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-52460 ER - TY - THES A1 - Gebauer, Denis T1 - A novel view on the early stage of crystallization T1 - Ein Neuartiges Bild der frühen Kristallisationsphase N2 - This thesis provides a novel view on the early stage of crystallization utilizing calcium carbonate as a model system. Calcium carbonate is of great economical, scientific and ecological importance, because it is a major part of water hardness, the most abundant Biomineral and forms huge amounts of geological sediments thus binding large amounts of carbon dioxide. The primary experiments base on the evolution of supersaturation via slow addition of dilute calcium chloride solution into dilute carbonate buffer. The time-dependent measurement of the Ca2+ potential and concurrent pH = constant titration facilitate the calculation of the amount of calcium and carbonate ions bound in pre-nucleation stage clusters, which have never been detected experimentally so far, and in the new phase after nucleation, respectively. Analytical Ultracentrifugation independently proves the existence of pre-nucleation stage clusters, and shows that the clusters forming at pH = 9.00 have a proximately time-averaged size of altogether 70 calcium and carbonate ions. Both experiments show that pre-nucleation stage cluster formation can be described by means of equilibrium thermodynamics. Effectively, the cluster formation equilibrium is physico-chemically characterized by means of a multiple-binding equilibrium of calcium ions to a ‘lattice’ of carbonate ions. The evaluation gives GIBBS standard energy for the formation of calcium/carbonate ion pairs in clusters, which exhibits a maximal value of approximately 17.2 kJ mol^-1 at pH = 9.75 and relates to a minimal binding strength in clusters at this pH-value. Nucleated calcium carbonate particles are amorphous at first and subsequently become crystalline. At high binding strength in clusters, only calcite (the thermodynamically stable polymorph) is finally obtained, while with decreasing binding strength in clusters, vaterite (the thermodynamically least stable polymorph) and presumably aragonite (the thermodynamically intermediate stable polymorph) are obtained additionally. Concurrently, two different solubility products of nucleated amorphous calcium carbonate (ACC) are detected at low binding strength and high binding strength in clusters (ACC I 3.1EE-8 M^2, ACC II 3.8EE-8 M^2), respectively, indicating the precipitation of at least two different ACC species, while the clusters provide the precursor species of ACC. It is proximate that ACC I may relate to calcitic ACC –i.e. ACC exhibiting short range order similar to the long range order of calcite and that ACC II may relate to vateritic ACC, which will subsequently transform into the particular crystalline polymorph as discussed in the literature, respectively. Detailed analysis of nucleated particles forming at minimal binding strength in clusters (pH = 9.75) by means of SEM, TEM, WAXS and light microscopy shows that predominantly vaterite with traces of calcite forms. The crystalline particles of early stages are composed of nano-crystallites of approximately 5 to 10 nm size, respectively, which are aligned in high mutual order as in mesocrystals. The analyses of precipitation at pH = 9.75 in presence of additives –polyacrylic acid (pAA) as a model compound for scale inhibitors and peptides exhibiting calcium carbonate binding affinity as model compounds for crystal modifiers- shows that ACC I and ACC II are precipitated in parallel: pAA stabilizes ACC II particles against crystallization leading to their dissolution for the benefit of crystals that form from ACC I and exclusively calcite is finally obtained. Concurrently, the peptide additives analogously inhibit the formation of calcite and exclusively vaterite is finally obtained in case of one of the peptide additives. These findings show that classical nucleation theory is hardly applicable for the nucleation of calcium carbonate. The metastable system is stabilized remarkably due to cluster formation, while clusters forming by means of equilibrium thermodynamics are the nucleation relevant species and not ions. Most likely, the concept of cluster formation is a common phenomenon occurring during the precipitation of hardly soluble compounds as qualitatively shown for calcium oxalate and calcium phosphate. This finding is important for the fundamental understanding of crystallization and nucleation-inhibition and modification by additives with impact on materials of huge scientific and industrial importance as well as for better understanding of the mass transport in crystallization. It can provide a novel basis for simulation and modelling approaches. New mechanisms of scale formation in Bio- and Geomineralization and also in scale inhibition on the basis of the newly reported reaction channel need to be considered. N2 - Die vorliegende Arbeit zeichnet ein neuartiges Bild der frühen Kristallisationsphase von Calciumcarbonat. Calciumcarbonat hat als Hauptbestandteil der Wasserhärte und als weit verbreitetes Biomineral und Geomineral, das als Sediment in den Ozeanen große Mengen Kohlendioxid bindet, große Bedeutung. Die grundlegenden Experimente basieren auf der sehr langsamen Einstellung von Übersättigung, die durch langsame Zugabe verdünnter Calciumlösung in verdünnten Carbonatpuffer erreicht wird. Zeitabhängige Messung des Ca2+ Potentials bei gleichzeitiger pH = konstant Titration zeigt, dass zeitgemittelt vor der Nukleation gleiche Stoffmengen von Calcium- und Carbonat Ionen in Clustern gebunden sind, die bis jetzt noch nicht experimentell nachgewiesen werden konnten. Analytische Ultrazentrifugation belegt unabhängig die Existenz der Cluster, und es zeigt sich, dass sich die bei pH = 9,00 bildenden Cluster zeitgemittelt aus insgesamt etwa 70 Calcium und Carbonat Ionen bestehen. Die Experimente weisen darauf hin, dass sich die Clusterbildung auf der Grundlage von Gleichgewichtsthermodynamik beschreiben lässt. Ein multiples Bindungsgleichgewichtsmodell ermöglicht die Bestimmung der freien Standard Reaktionsenthalpie für die Bildung von Calcium/Carbonat Ionenpaaren in den Clustern, die ein Maß für die Bindungsstärke in Clustern darstellt. Die Bindungsstärke weist ein Minimum bei pH = 9,75 auf, und es zeigt sich, dass außerhalb dieses Minimums amorphes Calciumcarbonat ausfällt, das sich letztendlich in Calcit (das thermodynamisch stabile Calciumcarbonat Polymorph) umwandelt, während im Minimum und in der Nähe des Minimums amorphes Calciumcarbonat ausfällt, das sich letztendlich hauptsächlich in Vaterit (das thermodynamisch am wenigsten stabile Polymorph), Calcit und möglicherweise Spuren von Aragonit (das Polymorph mittlerer Stabilität) umwandelt. Gleichzeitig treten zwei unterschiedliche Löslichkeitsprodukte für das bei hoher und niedriger Bindungsstärke in Clustern ausgefällte, amorphe Calciumcarbonat auf (ACC I 3,1EE-8 M^2, ACC II 3,8EE-8 M^2). Das zeigt, dass die sich vor der Nukleation bildenden Cluster Vorläuferspezies (Precursor) des ausgefällten, amorphen Calciumcarbonats darstellen, wobei ACC I in der Literatur diskutiertem, calcitischem ACC entsprechen und ACC II vateritischem Calcit entsprechen kann. Eine detaillierte SEM, TEM, WAXS und Lichtmikroskopie Untersuchung der bei minimaler Bindungsstärke in Clustern (pH = 9,75) ausgefällten Partikel zeigt, dass sich hauptsächlich Vaterit mit Spuren von Calcit und möglicherweise Aragonit bildet. Die sich früh bildenden, kristallinen Partikel sind jeweils aus nano-Kristalliten von etwa 5 bis 10 nm Größe aufgebaut, die wie in Mesokristallen eine hohe wechselseitige Ordnung aufweisen. Die Untersuchung der frühen Kristallisation in Gegenwart von Additiven wurde ebenfalls bei minimaler Bindungsstärke in Clustern durchgeführt. Als Additive wurden Polyacrylsäure (PAA) als Beispiel für einen Hemmstoff gegen die Bildung von Verkalkungen und drei Peptide, die Bindungsaffinität zu Calciumcarbonat zeigen, als Beispiel für Kristallisations-Modifikatoren untersucht. Die Analyse zeigt, dass ACC I und ACC II parallel ausfallen; pAA stabilisiert ACC II gegenüber Kristallisation und führt dazu, dass es sich zugunsten von Kristallen, die sich aus ACC I bilden, auflöst, wobei letztendlich reines Calcit erhalten wird. Die Peptide hingegen hemmen die Bildung von Calcit in analoger Weise, wobei in einem Fall letztendlich reines Vaterit entsteht. Die Ergebnisse zeigen, dass die klassische Nukleationstheorie auf die Nukleation von Calciumcarbonat kaum anwendbar ist. Das metastabile System wird durch die Clusterbildung deutlich stabilisiert, und nicht Ionen, sondern Cluster sind die relevanten Spezies in der Nukleation. Wahrscheinlich ist das gefundene Konzept der Clusterbildung ein allgemeines Phänomen, das während der Kristallisation aller schwer löslichen Substanzen auftritt, da es auch für Calciumoxalat und Calciumphosphat qualitativ gezeigt werden konnte. Das Ergebnis ist wichtig für das fundamentale Verständnis der Nukleation, von Nukleationshemmung und der Modifikation von Kristallen mit Auswirkungen auf Materialen von großer industrieller und auch wissenschaftlicher Bedeutung. Ferner gibt es einen Hinweis, wie Masse während der Kristallisation –auch in Lebewesen transportiert werden kann und es kann einen neuen Ansatz für Kristallisationssimulationen liefern. Auf der Basis dieses neuartigen Reaktionskanals müssen neue Kristallisations-Mechanismen in Bio- und Geomineralization in Betracht gezogen werden. KW - Calciumcarbonat KW - Kristallisation KW - Nukleation KW - Cluster KW - Additive KW - calcium carbonate KW - crystallization KW - nucleation KW - clusters KW - additives Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus-19818 ER - TY - THES A1 - Montenegro, Rivelino V. D. T1 - Crystallization, biomimetics and semiconducting polymers in confined systems T1 - Kristallisation, Biomimetik und halbleitende Polymere in räumlich begrenzten Systemen N2 - populärwissenschaftlicher Abstract: Kristallisation, Biomimetik und halbleitende Polymere in räumlich begrenzten Systemen: Öl und Wasser mischen sich nicht, man kann aber aus beiden Flüssigkeiten Emulsionen herstellen, bei denen Tröpfchen der einen Flüssigkeit in der anderen Flüssigkeit vorliegen. Das heißt, es können entweder Öltröpfchen in Wasser oder Wassertröpfchen in Öl erzeugt werden. Aus täglichen Erfahrungen, z.B. beim Kochen weiß man jedoch, dass sich eine Emulsion durch Schütteln oder Rühren herstellen lässt, diese jedoch nicht besonders stabil ist. Mit Hilfe von hohen Scherenergien kann man nun sehr kleine, in ihrer Größe sehr einheitliche und außerdem sehr stabile Tröpfchen von 1/10000 mm erhalten. Eine solche Emulsion wird Miniemulsion genannt. In der Dissertation wurden nun z.B. Miniemulsionen untersucht, die aus kleinen Wassertröpfchen in einem Öl bestehen. Es konnte gezeigt werden, dass das Wasser in diesen Tröpfchen, also in den räumlich begrenzten Systemen, nicht bei 0 °C, sondern bei -22 °C kristallisierte. Wie lässt sich das erklären? Wenn man einen Eimer Wasser hat, dann bildet sich normalerweise bei 0 °C Eis, da nämlich in dem Wasser einige (manchmal ganz wenige) Keime (z.B. Schutzteilchen, ein Fussel etc.) vorhanden sind, an denen sich die ersten Kristalle bilden. Wenn sich dann einmal ein Kristall gebildet hat, kann das Wasser im gesamten Eimer schnell zu Eis werden. Ultrareines Wasser würde bei -22 °C kristallisieren. Wenn man jetzt die Menge Wasser aus dem Eimer in kleine Tröpfchen bringt, dann hat man eine sehr, sehr große Zahl, nämlich 1017 Tröpfchen, in einem Liter Emulsion vorliegen. Die wenigen Schmutzpartikel verteilen auf sehr wenige Tröpfchen, die anderen Tröpfchen sind ultrarein. Daher kristallisieren sie erst bei -22 °C. Im Rahmen der Arbeit konnte auch gezeigt werden, dass die Miniemulsionen genutzt werden können, um kleine Gelatine-Partikel, also Nanogummibärchen, herzustellen. Diese Nanogummibärchen quellen bei Erhöhung der Temperatur auf ca. 38 °C an. Das kann ausgenutzt werden, um zum Beispiel Medikamente zunächst in den Partikeln im menschlichen Körper zu transportieren, die Medikamente werden dann an einer gewünschten Stelle freigelassen. In der Arbeit wurde auch gezeigt, dass die Gelatine-Partikel genutzt werden können, um die Natur nachzuahnen (Biomimetik). Innerhalb der Partikel kann nämlich gezielt Knochenmaterial aufgebaut werden kann. Die Gelatine-Knochen-Partikel können dazu genutzt werden, um schwer heilende oder komplizierte Knochenbrüche zu beheben. Gelatine wird nämlich nach einigen Tagen abgebaut, das Knochenmaterial kann in den Knochen eingebaut werden. LEDs werden heute bereits vielfältig verwendet. LEDs bestehen aus Halbleitern, wie z.B. Silizium. Neuerdings werden dazu auch halbleitende Polymere eingesetzt. Das große Problem bei diesen Materialien ist, dass sie aus Lösungsmitteln aufgebracht werden. Im Rahmen der Doktorarbeit wurde gezeigt, dass der Prozess der Miniemulsionen genutzt werden kann, um umweltfreundlich diese LEDs herzustellen. Man stellt dazu nun wässrige Dispersionen mit den Polymerpartikeln her. Damit hat man nicht nur das Lösungsmittel vermieden, das hat nun noch einen weiteren Vorteil: man kann nämlich diese Dispersion auf sehr einfache Art verdrucken, im einfachsten Fall verwendet man einfach einen handelsüblichen Tintenstrahldrucker. N2 - The colloidal systems are present everywhere in many varieties such as emulsions (liquid droplets dispersed in liquid), aerosols (liquid dispersed in gas), foam (gas in liquid), etc. Among several new methods for the preparation of colloids, the so-called miniemulsion technique has been shown to be one of the most promising. Miniemulsions are defined as stable emulsions consisting of droplets with a size of 50-500 nm by shearing a system containing oil, water, a surfactant, and a highly water insoluble compound, the so-called hydrophobe 1. In the first part of this work, dynamic crystallization and melting experiments are described which were performed in small, stable and narrowly distributed nanodroplets (confined systems) of miniemulsions. Both regular and inverse systems were examined, characterizing, first, the crystallization of hexadecane, secondly, the crystallization of ice. It was shown for both cases that the temperature of crystallization in such droplets is significantly decreased (or the required undercooling is increased) as compared to the bulk material. This was attributed to a very effective suppression of heterogeneous nucleation. It was also found that the required undercooling depends on the nanodroplet size: with decreasing droplet size the undercooling increases. 2. It is shown that the temperature of crystallization of other n-alkanes in nanodroplets is also significantly decreased as compared to the bulk material due to a very effective suppression of heterogeneous nucleation. A very different behavior was detected between odd and even alkanes. In even alkanes, the confinement in small droplets changes the crystal structure from a triclinic (as seen in bulk) to an orthorhombic structure, which is attributed to finite size effects inside the droplets. An intermediate metastable rotator phase is of less relevance for the miniemulsion droplets than in the bulk. For odd alkanes, only a strong temperature shift compared to the bulk system is observed, but no structure change. A triclinic structure is formed both in bulk and in miniemulsion droplets. 3. In the next part of the thesis it is shown how miniemulsions could be successfully applied in the development of materials with potential application in pharmaceutical and medical fields. The production of cross-linked gelatin nanoparticles is feasible. Starting from an inverse miniemulsion, the softness of the particles can be controlled by varying the initial concentration, amount of cross-link agent, time of cross-linking, among other parameters. Such particles show a thermo-reversible effect, e.g. the particles swell in water above 37 °C and shrink below this temperature. Above 37 °C the chains loose the physical cross-linking, however the particles do not loose their integrity, because of the chemical cross-linking. Those particles have potential use as drug carriers, since gelatin is a natural polymer derived from collagen. 4. The cross-linked gelatin nanoparticles have been used for the biomineralization of hydroxyapatite (HAP), a biomineral, which is the major constituent of our bones. The biomineralization of HAP crystals within the gelatin nanoparticles results in a hybrid material, which has potential use as a bone repair material. 5. In the last part of this work we have shown that layers of conjugated semiconducting polymers can be deposited from aqueous dispersion prepared by the miniemulsion process. Dispersions of particles of different conjugated semiconducting polymers such as a ladder-type poly(para-phenylene) and several soluble derivatives of polyfluorene could be prepared with well-controlled particle sizes ranging between 70 - 250 nm. Layers of polymer blends were prepared with controlled lateral dimensions of phase separation on sub-micrometer scales, utilizing either a mixture of single component nanoparticles or nanoparticles containing two polymers. From the results of energy transfer it is demonstrated that blending two polymers in the same particle leads to a higher efficiency due to the better contact between the polymers. Such an effect is of great interest for the fabrication of opto-electronic devices such as light emitting diodes with nanometer size emitting points and solar cells comprising of blends of electron donating and electron accepting polymers. KW - Confinement KW - miniemulsion KW - crystallization KW - biomimetics and semiconducting polymers Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-0000726 ER -