TY - JOUR A1 - Wang, Jingwen A1 - Rychkov, Dmitry A1 - Nguyen, Quyet Doan A1 - Gerhard, Reimund T1 - The influence of orthophosphoric-acid surface modification on charge-storage enhancement in polypropylene electrets JF - Journal of applied physics N2 - Bipolar electrets from polypropylene (PP) are essential, e.g., in electret air filters and in cellular-foam ferroelectrets. Therefore, the mechanism of surface-charge stability enhancement on PP electrets via orthophosphoric-acid surface treatment is investigated in detail. It is shown that the significant charge-stability enhancement can be mainly attributed to deeper surface traps originating from deposited chemicals and topographic features on the modified surfaces. Thermally stimulated discharge of chemically treated and non-treated PP films with different surface-charge densities is used to test the limits of the newly formed deep traps in terms of the capacity for hosting surface charges. When the initial surface-charge density is very high, more charges are forced into shallower original traps on the surface or in the bulk of the treated PP samples, reducing the effect of the deeper surface traps brought by the surface modification. The well-known crossover phenomenon (of the surface-charge decay curves) has been observed between modified PP electrets charged to +/- 2kV and to +/- 3kV. Acoustically probed charge distributions in the thickness direction of PP electrets at different stages of thermal discharging indicate that the deep surface trapping sites may have preference for negative charges, resulting in the observed asymmetric charge stability of the modified PP films. Y1 - 2020 U6 - https://doi.org/10.1063/5.0013805 SN - 0021-8979 SN - 1089-7550 VL - 128 IS - 3 PB - American Institute of Physics CY - Melville ER - TY - JOUR A1 - Wang, Jingwen A1 - Rychkov, Dmitry A1 - Nguyen, Quyet Doan A1 - Gerhard, Reimund T1 - Unexpected bipolar space-charge polarization across transcrystalline interfaces in polypropylene electret films JF - Journal of applied physics N2 - A double-layer transcrystalline polypropylene (PP) film with a flat central interface layer between its two transcrystalline layers is obtained by recrystallization from the melt between two polytetrafluoroethylene (PTFE) surfaces on both sides of the PP film. Its electret properties are studied and compared with those of a single-layer transcrystalline PP film re-crystallized in contact with only one PTFE surface. Within experimental uncertainty, the two types of transcrystalline films exhibit the same thermal properties and crystallinities. After thermal poling, however, two hetero-charge layers of opposite polarity are found on the internal interfaces of the double-layer transcrystalline films and may together be considered as micrometer-sized dipoles. The unexpected phenomenon does not occur in single-layer transcrystalline samples without a central interface layer, suggesting that the interfaces between the transcrystalline layers and the micrometer-thick central interface layer may be the origin of deeper traps rather than the crystalline structures in the transcrystallites or the spherulites. The origin of the interfacial charges was also studied by means of an injection-blocking charging method, which revealed that intrinsic charge carriers introduced during recrystallization are most likely responsible for the interfacial charges. It is fascinating that a material as familiar as PP can exhibit such intriguing properties with a special bipolar space-charge polarization across the central interface layer after quasi-epitaxial surface moulding into a double-layer transcrystalline form. In addition to applications in electret (micro-)devices for electro-mechanical transduction, the highly ordered structures may also be employed as a new paradigm for studying charge storage and transport in polymer electrets and in dielectrics for DC electrical insulation. Y1 - 2020 U6 - https://doi.org/10.1063/5.0022071 SN - 0021-8979 SN - 1089-7550 VL - 128 IS - 13 PB - American Institute of Physics, AIP CY - Melville, NY ER - TY - JOUR A1 - Wang, Jingwen A1 - Rychkov, Dmitry A1 - Gerhard, Reimund T1 - Chemical modification with orthophosphoric acid enhances surface-charge stability on polypropylene electrets JF - Applied physics letters N2 - The low surface-charge stability of polypropylene (PP) frequently limits its application as an electret material. In this paper, we demonstrate how the treatment of PP-film surfaces with orthophosphoric acid (H3PO4) enhances their charge stability. To discriminate between the effects of chemical modification and thermal treatment, as-received and annealed PP films are used as reference samples. The electret properties of treated and non-treated PP films are characterized with thermally stimulated discharge (TSD) and isothermal surface-potential decay (ISPD) experiments, from which considerable improvement in thermal and temporal charge stability is observed for samples modified with H3PO4. The half-value temperature (T-1/2) observed on TSD curves of chemically treated PP increases to 131 and 145 degrees C for positive and negative charges, respectively. The enhancement might be attributed to the phosphoric compounds detected on the H3PO4-modified surfaces via attenuated-total-reflection infrared spectroscopy. Deeper surface traps formed at the "foreign" phosphorus-containing structures are able to capture the charges over longer time periods and at higher temperatures, thus leading to significant improvements in the temporal and thermal surface-charge stabilities of PP electrets. Published by AIP Publishing. Y1 - 2017 U6 - https://doi.org/10.1063/1.4983348 SN - 0003-6951 SN - 1077-3118 VL - 110 PB - American Institute of Physics CY - Melville ER - TY - GEN A1 - Wang, Jingwen A1 - Rychkov, Dmitry A1 - Gerhard, Reimund T1 - Influence of Charge Density on Charge Decay in Chemically Modified Polypropylene Films T2 - 2018 IEEE 2nd International Conference on Dielectrics (ICD) N2 - Previous work has shown that surface modification with orthophosphoric acid can significantly enhance the charge stability on polypropylene (PP) surface by generating deeper traps. In the present study, thermally stimulated potential-decay measurements revealed that the chemical treatment may also significantly increase the number of available trapping sites on the surface. Thus, as a consequence, the so-called "cross-over" phenomenon, which is observed on as-received and thermally treated PP electrets, may be overcome in a certain range of initial charge densities. Furthermore, the discharge behavior of chemically modified samples indicates that charges can be injected from the treated surface into the bulk, and/or charges of opposite polarity can be pulled from the rear electrode into the bulk at elevated temperatures and at the high electric fields that are caused by the deposited charges. In the bulk, a lack of deep traps causes rapid charge decay already in the temperature range around 95 degrees C. KW - polypropylene KW - surface charge stability KW - thermally stimulated discharge KW - cross-over effect KW - chemical modification Y1 - 2018 SN - 978-1-5386-6389-9 U6 - https://doi.org/10.1109/ICD.2018.8514718 PB - IEEE CY - New York ER - TY - JOUR A1 - Wang, Jingwen A1 - Rychkov, Dmitry A1 - Gerhard, Reimund T1 - Space-charge electret properties of polypropylene films with transcrystalline or spherulitic structures BT - a comparison of functionalities at interfaces JF - Journal of applied physics : AIP's archival journal for significant new results in applied physics / publ. by the American Institute of Physics N2 - Spherulite-related space-charge electret properties of polypropylene (PP) have been widely discussed in the past decades. In the present paper, a less-common crystalline structure in PP-transcrystalline PP-is studied regarding its electret behavior in comparison with the typical spherulitic morphology. Polarized light microscopy and differential scanning calorimetry were employed to characterize the crystallite types and crystallinities of transcrystalline and spherulitic PP. Their electret functionality is investigated by means of thermally stimulated discharge experiments, where the cross-over phenomenon is observed on transcrystalline PP films, whereas surface-potential saturation and undercharging on the surface occur on the spherulitic samples. Besides, an asymmetrical behavior of positive and negative surface-charge stabilities is found on PP with spherulites, the negatively charged spherulitic surfaces show a better charge stability. It is shown that PP electrets are very sensitive to changes in the microscopic crystalline structures and their interfaces as well as in the molecular conformations controlled through adjustments of the respective processing steps. In addition, surface and bulk nanocomposites of PP or low-density polyethylene with inorganic particles are included in the comparison. In view of recent developments in the areas of PP-based electret-fiber filters and cellular-foam ferroelectrets, the observed changes in the charge-storage properties may have particular relevance, as the required film, fiber, or foam processing might significantly modify crystalline morphologies and nano-scale interfaces in PP electrets. Limitations in the charge-storage capabilities of interface structures may also be of interest in the context of high-voltage electrical-insulation materials where reduced space-charge accumulation and slightly increased charge transport can be advantageous. Y1 - 2021 U6 - https://doi.org/10.1063/5.0039867 SN - 0021-8979 SN - 1089-7550 VL - 129 IS - 6 PB - American Institute of Physics CY - Melville ER - TY - JOUR A1 - Rychkov, Dmitry A1 - Yablokov, M. A1 - Rychkov, A. T1 - Chemical and physical surface modification of PTFE films-an approach to produce stable electrets JF - Applied physics : A, Materials science & processing N2 - The thermal stability of positive charge has been investigated in chemically and physically treated polytetrafluoroethylene (PTFE) films. It has been found that virgin films, oriented by the manufacturer, display an increase in thermal stability of positive charge with an increase of the initial value of surface potential. Such an anomalous behavior is explained by the influence of a negative tribocharge, trapped some small distance below the surface. In PTFE samples treated with orthophosphoric acid and with tetraethoxysilane, a considerable improvement of positive charge stability has been achieved, but no influence of the initial value of surface potential has been observed. However, this influence should be kept in mind when comparing charge stability in virgin and modified samples. In nonoriented PTFE films, no influence of the initial value of surface potential on charge stability has been observed. This could be due to the fact that these films did not possess a noticeable negative tribocharge. After the treatment in glow-discharge defluorination, oxidation and appearance of polar groups have been detected on the surface. These changes in chemical composition of a PTFE surface resulted in a noticeable improvement in thermal stability of positively charged electrets. This improvement is attributed to the formation of deeper traps on the modified surface. Y1 - 2012 U6 - https://doi.org/10.1007/s00339-012-6834-5 SN - 0947-8396 VL - 107 IS - 3 SP - 589 EP - 596 PB - Springer CY - New York ER - TY - JOUR A1 - Rychkov, Dmitry A1 - Rychkov, A. A1 - Efimov, N. A1 - Malygin, A. A1 - Gerhard, Reimund T1 - Higher stabilities of positive and negative charge on tetrafluoroethylene-hexafluoropropylene copolymer (FEP) electrets treated with titanium-tetrachloride vapor JF - Applied physics : A, Materials science & processing N2 - Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor in a molecular-layer deposition process. As a result of the surface treatment, significant improvements of the thermal and temporal charge stability were observed. Charge-decay measurements revealed enhancements of the half-value temperatures and the relaxation times of positively charged FEP electrets by at least 120 A degrees C and two orders of magnitude, respectively. Beyond previous publications on fluoropolymer electrets with surface modification, we here report enhanced charge stabilities of the FEP films charged in negative as well as in positive corona discharges. Even though the improvement for negatively charged FEP films is moderate (half-value temperature about 20 A degrees C higher), our experiments show that the asymmetry in positive and negative charge stability that is typical for FEP electrets can be overcome by means of chemical surface treatments. The results are discussed in the context of the formation of modified surface layers with enhanced charge-trapping properties. Y1 - 2013 U6 - https://doi.org/10.1007/s00339-013-7821-1 SN - 0947-8396 VL - 112 IS - 2 SP - 283 EP - 287 PB - Springer CY - New York ER - TY - JOUR A1 - Rychkov, Dmitry A1 - Kuznetsov, Alexey A1 - Rychkov, Andrey T1 - Electret properties of polyethylene and polytetrafluoroethylene films with chemically modified surface JF - IEEE transactions on dielectrics and electrical insulation N2 - This paper investigates the effect of chemical surface modification of polytetrafluoroethylene (PTFE) and low density polyethylene (LDPE) films on their electret properties. PTFE films were subjected to wet treatment with three different chemicals: orthophosphoric acid, tetrabutyl titanate and tetraethoxysilane. The technique based on the principles of molecular layer deposition (MLD) method was used to modify the surface of LDPE films with phosphorus trichloride vapors. The surfaces of the films were then corona charged, and the electret charge stability was studied by means of isothermal and thermally stimulated surface potential decay. Both PTFE and LDPE films, after the surface treatment, displayed a considerable enhancement in the charge stability compared to the virgin samples. It is important to note that the enhancement of the charge stability was achieved in the positively charged PTFE films, a result important to practical applications. We attribute this effect of charge stabilization to the formation of new energetically deep traps on the modified surface. Decrease in molecular mobility, due to attachment of new chemical structures to the surface macromolecules, may also contribute to the overall growth of the charge stability. KW - Electrets KW - surface treatment KW - charge stability KW - charge carrier processes KW - polytetrafluoroethylene KW - polyethylene Y1 - 2011 U6 - https://doi.org/10.1109/TDEI.2011.5704487 SN - 1070-9878 VL - 18 IS - 1 SP - 8 EP - 14 PB - Inst. of Electr. and Electronics Engineers CY - Piscataway ER - TY - JOUR A1 - Rychkov, Dmitry A1 - Gerhard, Reimund A1 - Kuznetsov, Alexey A1 - Rychkov, Andrey T1 - Influence of charge density on the trap energy spectrum in fluoroethylenepropylene copolymer films with chemically modified surfaces JF - IEEE transactions on dielectrics and electrical insulation N2 - Tetrafluoroethylene-hexafluoropropylene copolymer (FEP) films were treated with titanium-tetrachloride vapor by means of molecular-layer deposition. The treatment leads to considerable improvements of the electret-charge stability on positively charged films. A slight improvement is also observed for negatively charged films. In line with our previous findings, we attribute the improvement in electret properties to the formation of deeper traps on the chemically modified polymer surfaces. Here, we investigate the influence of the charge density on electret stability of FEP films with modified surfaces. Trap-energy spectra obtained from thermally-stimulated-discharge measurements indicate that the charge stability on modified FEP films depends on how the surface traps are populated and on the availability of additional deeper traps. KW - Electrets KW - chemical modification KW - surface treatment KW - space-charge stability KW - charge-carrier transport KW - polytetrafluoroethylene (PTFE) KW - fluoroethylenepropylene (FEP) copolymer Y1 - 2018 U6 - https://doi.org/10.1109/TDEI.2018.007437 SN - 1070-9878 SN - 1558-4135 VL - 25 IS - 3 SP - 840 EP - 844 PB - Inst. of Electr. and Electronics Engineers CY - Piscataway ER - TY - JOUR A1 - Rychkov, Dmitry A1 - Gerhard, Reimund A1 - Ivanov, Vadim A1 - Rychkov, Andrey T1 - Enhanced electret charge stability on Polyethylene Films treated with Titanium-Tetrachloride vapor JF - IEEE transactions on dielectrics and electrical insulation N2 - Low-density polyethylene (LDPE) films have been treated with titanium-tetrachloride vapor by means of the molecular-layer-deposition method. It is shown that such a treatment leads to a considerable improvement of the electret properties for both positively and negatively charged films. The temperature stability of the electret homo-charge has been increased by approximately 60 degrees C. At the same time, the temporal stability of charge is also considerably improved. Modified low-density polyethylene films show no "cross-over phenomenon" when charged to higher voltages. Thus, it is now possible to produce electrets from polyethylene films with high initial charge densities, but without a strongly reduced charge stability. The influence of a chemical treatment with titanium-tetrachloride vapor on charge injection from aluminum electrodes into polyethylene films was also investigated. It is found that the interface between an aluminum electrode and a modified LDPE surface layer has different injection properties for positive and negative charges. Electrons can be injected across the modified interface, whereas injection of holes is either very limited or non-existent. KW - Electrets KW - chemical modification KW - surface treatment KW - space-charge stability KW - charge-carrier transport KW - polyethylene KW - low-density polyethylene KW - injection Y1 - 2012 SN - 1070-9878 VL - 19 IS - 4 SP - 1305 EP - 1311 PB - Inst. of Electr. and Electronics Engineers CY - Piscataway ER -