TY - JOUR A1 - Abbasi, Ali A1 - Xu, Yaolin A1 - Khezri, Ramin A1 - Etesami, Mohammad A1 - Lin, C. A1 - Kheawhom, Soorathep A1 - Lu, Yan T1 - Advances in characteristics improvement of polymeric membranes/separators for zinc-air batteries JF - Materials Today Sustainability N2 - Zinc-air batteries (ZABs) are gaining popularity for a wide range of applications due to their high energy density, excellent safety, and environmental friendliness. A membrane/separator is a critical component of ZABs, with substantial implications for battery performance and stability, particularly in the case of a battery in solid state format, which has captured increased attention in recent years. In this review, recent advances as well as insight into the architecture of polymeric membrane/separators for ZABs including porous polymer separators (PPSs), gel polymer electrolytes (GPEs), solid polymer electrolytes (SPEs) and anion exchange membranes (AEMs) are discussed. The paper puts forward strategies to enhance stability, ionic conductivity, ionic selectivity, electrolyte storage capacity and mechanical properties for each type of polymeric membrane. In addition, the remaining major obstacles as well as the most potential avenues for future research are examined in detail. KW - Ionic selectivity KW - Ionic conductivity KW - Gel polymer KW - Ion exchange KW - Porous KW - polymer Y1 - 2022 U6 - https://doi.org/10.1016/j.mtsust.2022.100126 SN - 2589-2347 VL - 18 PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Sharma, Anjali T1 - Optical manipulation of multi-responsive microgels N2 - This dissertation focuses on the understanding of the optical manipulation of microgels dispersed in aqueous solution of azobenzene containing surfactant. The work consists of three parts where each part is a systematic investigation of the (1) photo-isomerization kinetics of the surfactant in complex with the microgel polymer matrix, (2) light driven diffusiosmosis (LDDO) in microgels and (3) photo-responsivity of microgel on complexation with spiropyran. The first part comprises three publications where the first one [P1] investigates the photo-isomerization kinetics and corresponding isomer composition at a photo-stationary state of the photo-sensitive surfactant conjugated with charged polymers or micro sized polymer networks to understand the structural response of such photo-sensitive complexes. We report that the photo-isomerization of the azobenzene-containing cationic surfactant is slower in a polymer complex compared to being purely dissolved in an aqueous solution. The surfactant aggregates near the polyelectrolyte chains at concentrations much lower than the bulk critical micelle concentration. This, along with the inhibition of the photo-isomerization kinetics due to steric hindrance within the densely packed aggregates, pushes the isomer-ratio to a higher trans-isomer concentration for all irradiation wavelengths. The second publication [P2] combines experimental results and non-adiabatic dynamic simulations for the same surfactant molecules embedded in the micelles with absorption spectroscopy measurements of micellar solutions to uncover the reasons responsible for the slowdown in photo induced trans → cis azobenzene isomerization at concentrations higher than the critical micelle concentration (CMC). The simulations reveal a decrease of isomerization quantum yields for molecules inside the micelles and observes a reduction of extinction coefficients upon micellization. These findings explain the deceleration of the trans → cis switching in micelles of the azobenzene-containing surfactants. Finally, the third publication [P3] focusses on the kinetics of adsorption and desorption of the same surfactant within anionic microgels in the dark and under continuous irradiation. Experimental data demonstrate, that microgels can serve as a selective absorber of the trans isomers. The interaction of the isomers with the gel matrix induces a remotely controllable collapse or swelling on appropriate irradiation wavelengths. Measuring the kinetics of the microgel size response and knowing the exact isomer composition under light exposure, we calculate the adsorption rate of the trans-isomers. The second part comprises two publications. The first publication [P4] reports on the phenomenon of light-driven diffusioosmotic (DO) long-range attractive and repulsive interactions between micro-sized objects, whose range extends several times the size of microparticles and can be adjusted to point towards or away from the particle by varying irradiation parameters such as intensity or wavelength of light. The phenomenon is fueled by the aforementioned photosensitive surfactant. The complex interaction of dynamic exchange of isomers and photo-isomerization rate yields to relative concentrations gradients of the isomers in the vicinity of micro-sized object inducing a local diffusioosmotic (DO) flow thereby making a surface act as a micropump. The second publication [P5] exclusively aims the visualization and investigation of the DO flows generated from microgels by using small tracer particles. Similar to micro sized objects, the flow is able to push adjacent tracers over distances several times larger than microgel size. Here we report that the direction and the strength of the l-LDDO depends on the intensity, irradiation wavelength and the amount of surfactant adsorbed by the microgel. For example, the flow pattern around a microgel is directed radially outward and can be maintained quasi-indefinitely under exposure at 455 nm when the trans:cis ratio is 2:1, whereas irradiation at 365 nm, generates a radially transient flow pattern, which inverts at lower intensities. Lastly, the third part consists of one publication [P6] which, unlike the previous works, reports on the study of the kinetics of photo- and thermo-switching of a new surfactant namely, spiropyran, upon exposure with light of different wavelengths and its interaction with p(NIPAM-AA) microgels. The surfactant being an amphiphile, switches between its ring closed spiropyran (SP) form and ring open merocyanine (MC) form which results in a change in the hydrophilic–hydrophobic balance of the surfactant as MC being a zwitterionic form along with the charged head group, generates three charges on the molecule. Therefore, the MC form of the surfactant is more hydrophilic than in the case of the neutral SP state. Here, we investigate the initial shrinkage of the gel particles via charge compensation on first exposure to SP molecules which results from the complex formation of the molecules with the gel matrix, triggering them to become photo responsive. The size and VPTT of the microgels during irradiation is shown to be a combination of heating up of the solution during light absorption by the surfactant (more pronounced in the case of UV irradiation) and the change in the hydrophobicity of the surfactant. N2 - Diese Dissertation befasst sich mit dem Verständnis der optischen Manipulation von Mikrogelen, die in einer wässrigen Lösung eines azobenzol-haltigen Tensides mit einer kationischen Kopfgruppe, welches licht-sensitiv ist, dispergiert sind. Die Arbeit besteht aus drei Teilen, wobei jeder Teil eine systematische Untersuchung der (1) Photoisomerisierungskinetik des Tensids im Komplex mit der Mikrogel-Polymermatrix, (2) einer daraus induzierten lokalen lichtinduzierten Diffusiosmose (eng. local light driven diffusio osmosis, l-LDDO) in der Nähe von Mikrogelen und (3) der photo-responsivität von Mikrogelen bei Komplexierung mit Spiropyran darstellt. Der erste Teil umfasst drei Veröffentlichungen, von denen die erste [P1] die Photoisomerisierungskinetik und die entsprechende Isomerenzusammensetzung im photostationären Zustand dieses Tensids in Komplex mit Polyelektrolyten oder mikroskopisch kleinen Polymernetzwerken untersucht. Dabei verläuft die trans-cis-Kinetik in einem Polymerkomplex langsamer als in reinen wässrigen Lösungen, da innerhalb der Polyelektrolytnetzwerken eine erhöhte Mizellisierungstendez des licht-schaltbare Tensides vorliegt. In einer Mizelle ist die geometrische Molekülstrukturänderung vom trans- zum cis-Isomer kinetisch durch sterische Hindernisse von dicht gepackten benachbarten Tensiden gehemmt und führt dazu, dass das Isomerverhältnis bei allen Bestrahlungswellenlängen zu höheren trans-Isomerkonzentration im photostationären Zustand verschoben sind. Diese experimentellen Ergebnisse werden in der zweiten Veröffentlichung [P2] mittels nicht-adiabatische dynamische Simulationen unterstützt, wobei die Ergebnisse zeigen, dass Moleküle, welche einer Mizelle aggregiert sind, eine Abnahme der Isomerisierungsquantenausbeute mit einer gleichzeitigen Verringerung der Extinktionskoeffizienten die Verlangsamung der Kinetik bestätigen. Die dritte Veröffentlichung [P3] befasst sich mit der Kinetik des dynamischen Austauschverhalten desselben Tensids in anionischen Mikrogelen im Dunkeln aber auch unter kontinuierlicher Beleuchtung. Dabei kann die Größe des Mikrogeles bei geeigneten Beleuchtungswellenlängen zu einem lichtgesteuerten Kollaps oder Schwellen des Mikrogeles vollständig reversible induziert werden. Möglich ist dies, weil die Mikrogele als selektiver Absorber für die trans-Isomere dienen. Durch die Messung der Kinetik der Größenänderung des Mikrogels und die Kenntnis der kinetischen Daten aus den vorigen Publikationen wurde die Adsorptionsrate des trans-Isomere zum Mikrogel berechnet. Der zweite Teil umfasst zwei Veröffentlichungen. Der erste [P4] berichtet über das tiefere Verständnis der lokalen lichtinduzierten Diffusioosmose (l-LDDO) an verschiedenen Mikroobjekten, die abstoßende oder anziehende Ströme induzieren. Triebkraft dieses Mechanismus ist eine Verschiebung des cis-Isomerengleichgewichtes bei Beleuchtung und dessen resultierenden Konzentrationsgradienten der Isomere in der Nähe dieser Objekte, welche durch eine komplexe Wechselwirkung zwischen dem dynamischen Austausch von beiden Isomeren und einer unterschiedlichen Photo-Isomerisierungsrate an der Grenzfläche im Vergleich zum Kontinuum vorliegen. Stärke des l-LDDO hängt von typischen Lichtparameter (Intensität und Wellenlänge) und der Größe und Oberfläche der Mikropartikels ab. Unter geeigneten Bedingungen (hohe Lichtintensität) kann fast jede Oberfläche als Mikropumpe wirken. Die zweite Publikation [P5] befasst sich mit der Visualisierung und Untersuchung des l-LDDO von Mikrogelen unter Verwendung von kleinen Tracerpartikel. Ähnlich wie bei mikroskopisch kleinen Objekten können auch hier benachbarte Tracer über Entfernungen um ein Vielfaches größer als die Größe des Mikrogels bewegt werden. Die Richtung und die Stärke des l-LDDO hängt von der Intensität, der Wellenlänge der Bestrahlung und der Menge des vom Mikrogel adsorbierten Tensids ab. So ist beispielsweise das Strömungsmuster um ein Mikrogel radial nach außen gerichtet und kann bei einer Bestrahlung mit blauem Licht (455 nm) quasi unbegrenzt aufrechterhalten werden, während eine Bestrahlung mit UV-Licht (365 nm) mit niedrigen Intensitäten ein temporäres radial verlaufendes Strömungsmuster zum Mikrogel erzeugt. Schließlich besteht der dritte und letzte Teil dieser Dissertation aus einer Veröffentlichung [P6], die im Gegensatz zu den vorangegangenen Arbeiten über die Untersuchung der Kinetik des Photo- und Thermoschaltens eines Spiropyran basierten Tensides mit einer kationischen Kopfgruppe bei der Bestrahlung mit Licht verschiedener Wellenlängen und seiner Wechselwirkung mit Mikrogelen berichtet. Das Tensid wechselt zwischen seiner ringgeschlossenen Spiropyranform (SP) und seiner ringoffenen Merocyaninform (MC), was zu einer Änderung des hydrophilen/hydrophoben Gleichgewichts des Tensids führt. Die anfängliche Schrumpfung der Mikrogele bei der ersten Exposition gegenüber SP-Molekülen wurde untersucht, die auf einen Ladungsausgleich durch die Komplexierung der Moleküle mit der Gelmatrix zurückzuführen ist, wodurch das Mikrogel lichtempfindlich wird. Darüber hinaus wird gezeigt, dass die Temperatur des Größen- und Volumenphasenübergangs der Mikrogele unter Beleuchtung eine Kombination aus dem lichtinduzierten Austauschverhalten und der Erwärmung der Lösung durch die Lichtabsorption des Tensids ist, die unter UV-Bestrahlung besonders ausgeprägt ist. KW - optical manipulation KW - microgel KW - kinetics KW - surfactant KW - photo-isomerization KW - polymer KW - azobenzene KW - spectroscopy KW - microscopy Y1 - 2023 ER - TY - JOUR A1 - Lützow, Karola A1 - Weigel, Thomas A1 - Lendlein, Andreas T1 - Solvent-based fabrication method for magnetic, shape-memory nanocomposite foams JF - MRS advances N2 - This paper presents shape-memory foams that can be temporarily fixed in their compressed state and be expanded on demand. Highly porous, nanocomposite foams were prepared from a solution of polyetherurethane with suspended nanoparticles (mean aggregate size 90 nm) which have an iron(III) oxide core with a silica shell. The polymer solution with suspended nanoparticles was cooled down to -20 degrees C in a two-stage process, which was followed by freeze-drying. The average pore size increases with decreasing concentration of nanoparticles from 158 mu m to 230 mu m while the foam porosity remained constant. After fixation of a temporary form of the nanocomposite foams, shape recovery can be triggered either by heat or by exposure to an alternating magnetic field. Compressed foams showed a recovery rate of up to 76 +/- 4% in a thermochamber at 80 degrees C, and a slightly lower recovery rate of up to 65 +/- 4% in a magnetic field. KW - composite KW - foam KW - polymer KW - magnetic KW - shape memory Y1 - 2020 U6 - https://doi.org/10.1557/adv.2019.422 SN - 2059-8521 VL - 5 IS - 14-15 SP - 785 EP - 795 PB - Cambridge Univ. Press CY - Cambridge ER - TY - JOUR A1 - Izraylit, Victor A1 - Gould, Oliver E. C. A1 - Kratz, Karl A1 - Lendlein, Andreas T1 - Investigating the phase-morphology of PLLA-PCL multiblock copolymer/PDLA blends cross-linked using stereocomplexation JF - MRS advances N2 - The macroscale function of multicomponent polymeric materials is dependent on their phase-morphology. Here, we investigate the morphological structure of a multiblock copolymer consisting of poly(L-lactide) and poly(epsilon-caprolactone) segments (PLLA-PCL), physically cross-linked by stereocomplexation with a low molecular weight poly(D-lactide) oligomer (PDLA). The effects of blend composition and PLLA-PCL molecular structure on the morphology are elucidated by AFM, TEM and SAXS. We identify the formation of a lattice pattern, composed of PLA domains within a PCL matrix, with an average domain spacing d0 = 12 - 19 nm. The size of the PLA domains were found to be proportional to the block length of the PCL segment of the copolymer and inversely proportional to the PDLA content of the blend. Changing the PLLA-PCL / PDLA ratio caused a shift in the melt transition Tm attributed to the PLA stereocomplex crystallites, indicating partial amorphous phase dilution of the PLA and PCL components within the semicrystalline material. By elucidating the phase structure and thermal character of multifunctional PLLA-PCL / PDLA blends, we illustrate how composition affects the internal structure and thermal properties of multicomponent polymeric materials. This study should facilitate the more effective incorporation of a variety of polymeric structural units capable of stimuli responsive phase transitions, where an understanding the phase-morphology of each component will enable the production of multifunctional soft-actuators with enhanced performance. KW - polymer KW - blend KW - nanostructure KW - morphology Y1 - 2020 U6 - https://doi.org/10.1557/adv.2019.465 SN - 2059-8521 VL - 5 IS - 14-15 SP - 699 EP - 707 PB - Cambridge Univ. Press CY - New York ER - TY - JOUR A1 - Behl, Marc A1 - Balk, Maria A1 - Mansfeld, Ulrich A1 - Lendlein, Andreas T1 - Phase morphology of multiblock copolymers differing in sequence of blocks JF - Macromolecular materials and engineering N2 - The chemical nature, the number length of integrated building blocks, as well as their sequence structure impact the phase morphology of multiblock copolymers (MBC) consisting of two non-miscible block types. It is hypothesized that a strictly alternating sequence should impact phase segregation. A library of well-defined MBC obtained by coupling oligo(epsilon-caprolactone) (OCL) of different molecular weights (2, 4, and 8 kDa) with oligotetrahydrofuran (OTHF, 2.9 kDa) via Steglich esterification results in strictly alternating (MBCalt) or random (MBCran) MBC. The three different series has a weight average molecular weight (M-w) of 65 000, 165 000, and 168 000 g mol(-1) for MBCalt and 80 500, 100 000, and 147 600 g mol(-1) for MBCran. When the chain length of OCL building blocks is increased, the tendency for phase segregation is facilitated, which is attributed to the decrease in chain mobility within the MBC. Furthermore, it is found that the phase segregation disturbs the crystallization by causing heterogeneities in the semi-crystalline alignment, which is attributed to an increase of the disorder of the OCL semi-crystalline alignment. KW - electron microscopy KW - multiblock copolymers KW - phase morphology KW - polymer KW - libraries KW - sequence structures KW - wide angle x‐ ray scattering Y1 - 2021 U6 - https://doi.org/10.1002/mame.202000672 SN - 1439-2054 VL - 306 IS - 3 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Behl, Marc A1 - Zhao, Qian A1 - Lendlein, Andreas T1 - Glucose-responsive shape-memory cryogels JF - Journal of materials research : JMR N2 - Boronic ester bonds can be reversibly formed between phenylboronic acid (PBA) and triol moieties. Here, we aim at a glucose-induced shape-memory effect by implementing such bonds as temporary netpoints, which are cleavable by glucose and by minimizing the volume change upon stimulation by a porous cryogel structure. The polymer system consisted of a semi-interpenetrating network (semi-IPN) architecture, in which the triol moieties were part of the permanent network and the PBA moieties were located in the linear polymer diffused into the semi-IPN. In an alkaline medium (pH = 10), the swelling ratio was approximately 35, independent of C-glu varied between 0 and 300 mg/dL. In bending experiments, shape fixity R-f approximate to 80% and shape recovery R-r approximate to 100% from five programming/recovery cycles could be determined. R-r was a function of C-glu in the range from 0 to 300 mg/dL, which accords with the fluctuation range of C-glu in human blood. In this way, the shape-memory hydrogels could play a role in future diabetes treatment options. KW - shape memory KW - polymer KW - porosity Y1 - 2020 U6 - https://doi.org/10.1557/jmr.2020.204 SN - 0884-2914 SN - 2044-5326 VL - 35 IS - 18 SP - 2396 EP - 2404 PB - Springer CY - Berlin ER - TY - THES A1 - Saatchi, Mersa T1 - Study on manufacturing of multifunctional bilayer systems N2 - Layered structures are ubiquitous in nature and industrial products, in which individual layers could have different mechanical/thermal properties and functions independently contributing to the performance of the whole layered structure for their relevant application. Tuning each layer affects the performance of the whole layered system. Pores are utilized in various disciplines, where low density, but large surfaces are demanded. Besides, open and interconnected pores would act as a transferring channel for guest chemical molecules. The shape of pores influences compression behavior of the material. Moreover, introducing pores decreases the density and subsequently the mechanical strength. To maintain defined mechanical strength under various stress, porous structure can be reinforced by adding reinforcement agent such as fiber, filler or layered structure to bear the mechanical stress on demanded application. In this context, this thesis aimed to generate new functions in bilayer systems by combining layers having different moduli and/or porosity, and to develop suitable processing techniques to access these structures. Manufacturing processes of layered structures employ often organic solvents mostly causing environmental pollution. In this regard, the studied bilayer structures here were manufactured by processes free of organic solvents. In this thesis, three bilayer systems were studied to answer the individual questions. First, while various methods of introducing pores in melt-phase are reported for one-layer constructs with simple geometry, can such methods be applied to a bilayer structure, giving two porous layers? This was addressed with Bilayer System 1. Two porous layers were obtained from melt-blending of two different polyurethanes (PU) and polyvinyl alcohol (PVA) in a co-continuous phase followed by sequential injection molding and leaching the PVA phase in deionized water. A porosity of 50 ± 5% with a high interconnectivity was obtained, in which the pore sizes in both layers ranged from 1 µm to 100 µm with an average of 22 µm in both layers. The obtained pores were tailored by applying an annealing treatment at relevant high temperatures of 110 °C and 130 °C, which allowed the porosity to be kept constant. The disadvantage of this system is that a maximum of 50% porosity could be reached and removal of leaching material in the weld line section of both layers is not guaranteed. Such a construct serves as a model for bilayer porous structure for determining structure-property relationships with respect to the pore size, porosity and mechanical properties of each layer. This fabrication method is also applicable to complex geometries by designing a relevant mold for injection molding. Secondly, utilizing scCO2 foaming process at elevated temperature and pressure is considered as a green manufacturing process. Employing this method as a post-treatment can alter the history orientation of polymer chains created by previous fabrication methods. Can a bilayer structure be fabricated by a combination of sequential injection molding and scCO2 foaming process, in which a porous layer is supported by a compact layer? Such a construct (Bilayer System 2) was generated by sequential injection molding of a PCL (Tm ≈ 58 °C) layer and a PLLA (Tg ≈ 58 °C) layer. Soaking this structure in the autoclave with scCO2 at T = 45 °C and P = 100 bar led to the selective foaming of PCL with a porosity of 80%, while the PLA layer was kept compact. The scCO2 autoclave led to the formation of a porous core and skin layer of the PCL, however, the degree of crystallinity of PLLA layer increased from 0 to 50% at the defined temperature and pressure. The microcellular structure of PCL as well as the degree of crystallinity of PLLA were controlled by increasing soaking time. Thirdly, wrinkles on surfaces in micro/nano scale alter the properties, which are surface-related. Wrinkles are formed on a surface of a bilayer structure having a compliant substrate and a stiff thin film. However, the reported wrinkles were not reversible. Moreover, dynamic wrinkles in nano and micro scale have numerous examples in nature such as gecko foot hair offering reversible adhesion and an ability of lotus leaves for self-cleaning altering hydrophobicity of the surface. It was envisioned to imitate this biomimetic function on the bilayer structure, where self-assembly on/off patterns would be realized on the surface of this construct. In summary, developing layered constructs having different properties/functions in the individual layer or exhibiting a new function as the consequence of layered structure can give novel insight for designing layered constructs in various disciplines such as packaging and transport industry, aerospace industry and health technology. N2 - Schichtstrukturen sind in der Natur und in Industrieprodukten allgegenwärtig, wobei die einzelnen Schichten unterschiedliche mechanische/thermische Eigenschaften und Funktionen haben können, die unabhängig voneinander zur Leistungsfähigkeit der gesamten Schichtstruktur für die jeweilige Anwendung beitragen. Die individuelle Abstimmung jeder einzelnen Schicht wirkt sich auf die Leistungsfähigkeit des gesamten Schichtsystems aus. Poren werden in verschiedenen Bereichen eingesetzt, in denen eine geringe Dichte, aber eine große Oberfläche erforderlich ist. Außerdem können offene und miteinander verbundene Poren als Übertragungskanal für chemische Gast-Moleküle dienen. Die Form der Poren beeinflusst das Kompressionsverhalten des Materials. In diesem Zusammenhang zielte diese Arbeit darauf ab, neue Funktionen in zweischichtigen Systemen durch die Kombination von Schichten mit unterschiedlichen Modulen und/oder Porosität zu erzeugen und geeignete Verarbeitungstechniken zu entwickeln, um diese Strukturen zu erreichen. Bei der Herstellung von Schichtstrukturen werden häufig organische Lösungsmittel verwendet, die meist eine Umweltbelastung darstellen. Daher wurden die hier untersuchten Doppelschichtstrukturen mit Verfahren hergestellt, die frei von organischen Lösungsmitteln sind. In dieser Arbeit wurden drei Doppelschichtsysteme untersucht, um die einzelnen Fragen zu beantworten. Erstens: Während verschiedene Methoden zur Einführung von Poren in der Schmelzphase für einschichtige Konstruktionen mit einfacher Geometrie bekannt sind, stellt sich die Frage, ob solche Methoden sich auf eine zweischichtige Struktur anwenden lassen und somit zwei unterschiedlich poröse Schichten ergibt? Dies wurde mit dem Zweischichtsystem 1 untersucht. Zwei poröse Schichten wurden durch das Mischen in der Schmelze von zwei verschiedenen Polyurethanen (PU) und Polyvinylalkohol (PVA) in einer co-kontinuierlichen Phase erhalten. Es folgte sequentielles Spritzgießen und das Entfernen der PVA-Phase durch „Leaching“ in entionisiertem Wasser. Es wurde eine Porosität von 50 ± 5 % mit einer hohen Interkonnektivität erzielt, wobei die Porengrößen in beiden Schichten zwischen 1 µm und 100 µm lagen, mit einem Durchschnittswert von 22 µm in beiden Schichten. Diese Herstellungsmethode ist auch auf komplexe Geometrien anwendbar, es muss lediglich eine entsprechende Form für das Spritzgießen entworfen werden. Zweitens: die Verwendung des scCO2-Schäumungsverfahrens bei erhöhter Temperatur und erhöhtem Druck wird als umweltfreundlicher Herstellungsprozess betrachtet. Durch den Einsatz dieser Methode als Nachbehandlung kann die Historie der Ausrichtung der Polymerketten, die durch frühere Herstellungsmethoden entstanden ist, verändert werden. Kann eine zweischichtige Struktur durch eine Kombination aus sequentiellem Spritzgießen und scCO2-Schäumverfahren hergestellt werden, bei der eine poröse Schicht von einer kompakten Schicht getragen wird? Ein solches Konstrukt (Bilayer System 2) wurde durch sequentielles Spritzgießen einer PCL-Schicht (Tm ≈ 58 °C) und einer PLLA-Schicht (Tg ≈ 58 °C) erzeugt. Das Einweichen dieser Struktur in scCO2 im Autoklaven bei T = 45 °C und P = 100 bar führte zum selektiven Aufschäumen von PCL mit einer Porosität von 80%, während die PLA-Schicht unverschäumt blieb. Die Behandlung im scCO2-Autoklav führte zur Bildung einer porösen Kern- und Hautschicht des PCL, während der Kristallinitätsgrad der PLLA-Schicht bei der definierten Temperatur und dem definierten Druck von 0 auf 50 % anstieg. Die mikrozelluläre Struktur von PCL sowie der Kristallinitätsgrad von PLLA wurden durch die Erhöhung der Einweichzeit gesteuert. Drittens verändern Falten auf Oberflächen im Mikro-/Nanomaßstab die Eigenschaften, die mit der Oberfläche zusammenhängen. Falten bilden sich auf der Oberfläche einer zweischichtigen Struktur mit einem nachgiebigen Substrat und einem steifen dünnen Film. Die Falten waren jedoch nicht reversibel. Darüber hinaus gibt es in der Natur zahlreiche Beispiele für dynamische Falten im Nano- und Mikromaßstab, wie z. B. Gecko-Fußhaare, die eine reversible Adhäsion ermöglichen, und die Fähigkeit von Lotusblättern, sich selbst zu reinigen, indem sie die Hydrophobizität der Oberfläche verändern. Diese biomimetische Funktion sollte auf der Doppelschichtstruktur nachgeahmt werden, wobei auf der Oberfläche dieses Konstrukts selbstorganisierende On/Off-Muster realisiert werden sollten. Zusammenfassend kann gesagt werden, dass die Entwicklung geschichteter Konstrukte mit unterschiedlichen Eigenschaften/Funktionen in den einzelnen Schichten oder mit einer neuen Funktion als Folge der geschichteten Struktur neue Erkenntnisse für den Entwurf geschichteter Konstrukte in verschiedenen Disziplinen wie der Verpackungs- und Transportindustrie, der Luft- und Raumfahrtindustrie und der Gesundheitstechnologie liefern kann. T2 - Studie zur Herstellung multifunktionaler Doppelschichtsysteme KW - bilayer system KW - biomaterials KW - wrinkles KW - polymer KW - injection molding KW - Doppelschichtstruktur KW - Biomaterialien KW - poröse Struktur KW - Falten KW - Spritzgießen Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-601968 ER - TY - JOUR A1 - Balk, Maria A1 - Behl, Marc A1 - Lendlein, Andreas T1 - Actuators based on oligo[(epsilon-caprolactone)-co-glycolide] with accelerated hydrolytic degradation JF - MRS advances : a journal of the Materials Research Society (MRS) N2 - Polyester-based shape-memory polymer actuators are multifunctional materials providing reversible macroscopic shape shifts as well as hydrolytic degradability. Here, the function-function interdependencies (between shape shifts and degradation behaviour) will determine actuation performance and its life time. In this work, glycolide units were incorporated in poly(epsilon-caprolactone) based actuator materials in order to achieve an accelerated hydrolytic degradation and to explore the function-function relationship. Three different oligo[(epsilon-caprolactone)-co-glycolide] copolymers (OCGs) with similar molecular weights (10.5 +/- 0.5 kg center dot mol(-1)) including a glycolide content of 8, 16, and 26 mol% (ratio 1:1:1 wt%) terminated with methacrylated moieties were crosslinked. The obtained actuators provided a broad melting transition in the range from 27 to 44 degrees C. The hydrolytic degradation of programmed OCG actuators (200% of elongation) resulted in a reduction of sample mass to 51 wt% within 21 days at pH = 7.4 and 40 degrees C. Degradation results in a decrease of T-m associated to the actuating units and increasing T-m associated to the skeleton forming units. The actuation capability decreased almost linear as function of time. After 11 days of hydrolytic degradation the shape-memory functionality was lost. Accordingly, a fast degradation behaviour as required, e.g., for actuator materials intended as implant material can be realized. KW - actuation KW - shape memory KW - polymer KW - crystalline Y1 - 2020 U6 - https://doi.org/10.1557/adv.2019.447 SN - 2059-8521 VL - 5 IS - 12-13 SP - 655 EP - 666 PB - Cambridge University Press CY - New York, NY ER - TY - THES A1 - Hain, Tobias Martin T1 - Structure formation and identification in geometrically driven soft matter systems T1 - Strukturbildung und Identifikation in geometrisch getriebenen weiche Materie-Systemen N2 - Subdividing space through interfaces leads to many space partitions that are relevant to soft matter self-assembly. Prominent examples include cellular media, e.g. soap froths, which are bubbles of air separated by interfaces of soap and water, but also more complex partitions such as bicontinuous minimal surfaces. Using computer simulations, this thesis analyses soft matter systems in terms of the relationship between the physical forces between the system's constituents and the structure of the resulting interfaces or partitions. The focus is on two systems, copolymeric self-assembly and the so-called Quantizer problem, where the driving force of structure formation, the minimisation of the free-energy, is an interplay of surface area minimisation and stretching contributions, favouring cells of uniform thickness. In the first part of the thesis we address copolymeric phase formation with sharp interfaces. We analyse a columnar copolymer system "forced" to assemble on a spherical surface, where the perfect solution, the hexagonal tiling, is topologically prohibited. For a system of three-armed copolymers, the resulting structure is described by solutions of the so-called Thomson problem, the search of minimal energy configurations of repelling charges on a sphere. We find three intertwined Thomson problem solutions on a single sphere, occurring at a probability depending on the radius of the substrate. We then investigate the formation of amorphous and crystalline structures in the Quantizer system, a particulate model with an energy functional without surface tension that favours spherical cells of equal size. We find that quasi-static equilibrium cooling allows the Quantizer system to crystallise into a BCC ground state, whereas quenching and non-equilibrium cooling, i.e. cooling at slower rates then quenching, leads to an approximately hyperuniform, amorphous state. The assumed universality of the latter, i.e. independence of energy minimisation method or initial configuration, is strengthened by our results. We expand the Quantizer system by introducing interface tension, creating a model that we find to mimic polymeric micelle systems: An order-disorder phase transition is observed with a stable Frank-Caspar phase. The second part considers bicontinuous partitions of space into two network-like domains, and introduces an open-source tool for the identification of structures in electron microscopy images. We expand a method of matching experimentally accessible projections with computed projections of potential structures, introduced by Deng and Mieczkowski (1998). The computed structures are modelled using nodal representations of constant-mean-curvature surfaces. A case study conducted on etioplast cell membranes in chloroplast precursors establishes the double Diamond surface structure to be dominant in these plant cells. We automate the matching process employing deep-learning methods, which manage to identify structures with excellent accuracy. N2 - Die Unterteilung eines Raums durch Grenzflächen führt zu Raumaufteilungen, die für die Selbstorganisation weicher Materie relevant sind. Bekannte Beispiele sind zelluläre Medien, wie z.B. Seifenschaum, der aus Luftblasen besteht, getrennt durch Wände aus Wasser und Seife, und komplexere Partitionen, wie sie z.B. durch bikontinuierliche Minimalflächen erzeugt werden. In dieser Arbeit werden mit Hilfe von Computersimulationen Systeme weicher Materie in Bezug auf den Zusammenhang zwischen dem im System vorherrschenden, physikalischen Kräften und der Struktur der resultierenden Grenzflächen oder Partitionen untersucht. Der Schwerpunkt liegt hierbei auf zwei Systemen, eine Copolymerschmelze und das sogenannte Quantizer Problem, bei denen der treibende Faktor der Strukturbildung, nämlich die Minimierung der freien Energie, aus einem Zusammenspiel der Minimierung der Oberfläche der Grenzflächen und der gleichzeitigen Minimierung der Elastizitätsenergie besteht. Unter diesen Gegebenheiten bevorzugen solche Systeme Zellen gleichmäßiger Größe. Im ersten Teil der Arbeit befassen wir uns mit der Bildung von scharfen Grenzflächen in Systemen von Copolymeren. Wir analysieren die zylindrische Phase eines Copolymersystems, das gezwungen wird, sich auf einer kugelförmigen Oberfläche zu organisieren. Die Topologie dieser Oberfläche erlaubt es der optimalen Konfiguration, dem Sechseckgitter, nicht, sich zu bilden. Für dreiarmige Copolymere wird die entstehende Struktur durch Lösungen des sogenannten Thomson Problems beschrieben. Letzteres sucht nach der Konfigurationen von abstoßenden Ladungen auf einer Kugeloberfläche mit minimaler Energie. Auf einem Substrat haben wir eine Kombination aus drei ineinandergreifende Lösungen des Thomson Problems gefunden, wobei der Typ der Lösungen statistisch von dem Radius des Substrates abhängt. Anschließend untersuchen wir die Bildung von amorphen und kristallinen Strukturen im Quantizersystem, einem teilchenbasierenden Modell, dessen Energiefunktional keine Oberflächenspannung enthält und möglichst kugelförmige Zellen gleicher Größe begünstigt. Wird das System quasistatisch im thermodynamischen Gleichgewicht abgekühlt, kristallisiert das Quantizersystem in den geordneten BCC Grundzustand. Wird das System allerdings zu schnell abgekühlt, sodass es sich nicht mehr im thermodynamischen Gleichgewicht befindet, bildet sich eine amorphe, annähernd hyperuniforme Struktur aus. Wir konnten zeigen, dass diese Struktur bemerkenswert unabhängig von den Ausganszuständen, sowie der Art der Energieminimierung zu sein scheint. Im Ausblick erweitern wir das Quantizersystem, indem wir Oberflächenspannung einführen. Unsere Ergebnisse deutet darauf hin, dass dieses so erweiterte Modell Mizellenphasen in Polymersystem modellieren kann. Wir beobachten einen Phasenübergang von einer ungeordneten, flüssigen Phase hin zu einer festen Frank-Caspar-Phase. Der zweite Teil der Arbeit behandelt bikontinuierliche Grenzflächen, die den Raum in zwei netzwerkartige Domänen aufteilen. Wir führen eine Open-Source Software ein, das die Identifizierung von Strukturen anhand derer Mikroskopaufnahmen ermöglicht. Hierzu erweitern und verbessern wir eine Methode, die durch den Abgleich experimentell zugänglicher Projektionen in Mikroskopaufnahmen mit berechneten Projektionen potenzieller Strukturen basiert. Dieses Verfahren wurde erstmal von Deng und Mieczkowski (1998) eingeführt. Die simulierten Strukturen basieren auf einer Nodalflächenmodellierung von dreifach-periodischen Flächen konstanter mittlerer Krümmung. Wir führen eine Fallstudie an Zellmembranen von Etioplasten, den Vorläufern von Chloroplasten, durch. Wir konnten die Struktur dieser Etioplasten als die Diamond-Struktur identifizieren. Als Ausblick automatisieren wir den Identifizierungsproyess mit Hilfe von Deep-Learning-Methoden. Erste Ergebnisse zeigen, dass mit diesem Ansatz die Identifizierung von Strukturen mit ausgezeichneter Genauigkeit gelingt. KW - soft matter KW - geometry KW - self-assembly KW - structure formation KW - quantizer KW - polymer KW - Geometrie KW - Polymere KW - Quantizer KW - Selbstassemblierung KW - weiche Materie KW - Strukturbildung Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-558808 N1 - Parts of this publication are reproduced with permission from the Royal Society of Chemistry and AIP Publishing. ER - TY - THES A1 - Saretia, Shivam T1 - Modulating ultrathin films of semi-crystalline oligomers by Langmuir technique T1 - Modulation ultradünner Filme aus semikristalliner Oligomere durch Langmuir-Technik N2 - Polymeric films and coatings derived from semi-crystalline oligomers are of relevance for medical and pharmaceutical applications. In this context, the material surface is of particular importance, as it mediates the interaction with the biological system. Two dimensional (2D) systems and ultrathin films are used to model this interface. However, conventional techniques for their preparation, such as spin coating or dip coating, have disadvantages, since the morphology and chain packing of the generated films can only be controlled to a limited extent and adsorption on the substrate used affects the behavior of the films. Detaching and transferring the films prepared by such techniques requires additional sacrificial or supporting layers, and free-standing or self supporting domains are usually of very limited lateral extension. The aim of this thesis is to study and modulate crystallization, melting, degradation and chemical reactions in ultrathin films of oligo(ε-caprolactone)s (OCL)s with different end-groups under ambient conditions. Here, oligomeric ultrathin films are assembled at the air-water interface using the Langmuir technique. The water surface allows lateral movement and aggregation of the oligomers, which, unlike solid substrates, enables dynamic physical and chemical interaction of the molecules. Parameters like surface pressure (π), temperature and mean molecular area (MMA) allow controlled assembly and manipulation of oligomer molecules when using the Langmuir technique. The π-MMA isotherms, Brewster angle microscopy (BAM), and interfacial infrared spectroscopy assist in detecting morphological and physicochemical changes in the film. Ultrathin films can be easily transferred to the solid silicon surface via Langmuir Schaefer (LS) method (horizontal substrate dipping). Here, the films transferred on silicon are investigated using atomic force microscopy (AFM) and optical microscopy and are compared to the films on the water surface. The semi-crystalline morphology (lamellar thicknesses, crystal number densities, and lateral crystal dimensions) is tuned by the chemical structure of the OCL end-groups (hydroxy or methacrylate) and by the crystallization temperature (Tc; 12 or 21 °C) or MMAs. Compression to lower MMA of ~2 Å2, results in the formation of a highly crystalline film, which consists of tightly packed single crystals. Preparation of tightly packed single crystals on a cm2 scale is not possible by conventional techniques. Upon transfer to a solid surface, these films retain their crystalline morphology whereas amorphous films undergo dewetting. The melting temperature (Tm) of OCL single crystals at the water and the solid surface is found proportional to the inverse crystal thickness and is generally lower than the Tm of bulk PCL. The impact of OCL end-groups on melting behavior is most noticeable at the air-solid interface, where the methacrylate end-capped OCL (OCDME) melted at lower temperatures than the hydroxy end-capped OCL (OCDOL). When comparing the underlying substrate, melting/recrystallization of OCL ultrathin films is possible at lower temperatures at the air water interface than at the air-solid interface, where recrystallization is not visible. Recrystallization at the air-water interface usually occurs at a higher temperature than the initial Tc. Controlled degradation is crucial for the predictable performance of degradable polymeric biomaterials. Degradation of ultrathin films is carried out under acidic (pH ~ 1) or enzymatic catalysis (lipase from Pseudomonas cepcia) on the water surface or on a silicon surface as transferred films. A high crystallinity strongly reduces the hydrolytic but not the enzymatic degradation rate. As an influence of end-groups, the methacrylate end-capped linear oligomer, OCDME (~85 ± 2 % end-group functionalization) hydrolytically degrades faster than the hydroxy end capped linear oligomer, OCDOL (~95 ± 3 % end-group functionalization) at different temperatures. Differences in the acceleration of hydrolytic degradation of semi-crystalline films were observed upon complete melting, partial melting of the crystals, or by heating to temperatures close to Tm. Therefore, films of densely packed single crystals are suitable as barrier layers with thermally switchable degradation rates. Chemical modification in ultrathin films is an intricate process applicable to connect functionalized molecules, impart stability or create stimuli-sensitive cross-links. The reaction of end-groups is explored for transferred single crystals on a solid surface or amorphous monolayer at the air-water interface. Bulky methacrylate end-groups are expelled to the crystal surface during chain-folded crystallization. The density of end-groups is inversely proportional to molecular weight and hence very pronounced for oligomers. The methacrylate end-groups at the crystal surface, which are present at high concentration, can be used for further chemical functionalization. This is demonstrated by fluorescence microscopy after reaction with fluorescein dimethacrylate. The thermoswitching behavior (melting and recrystallization) of fluorescein functionalized single crystals shows the temperature-dependent distribution of the chemically linked fluorescein moieties, which are accumulated on the surfaces of crystals, and homogeneously dispersed when the crystals are molten. In amorphous monolayers at the air-water interface, reversible cross-linking of hydroxy-terminated oligo(ε-caprolactone) monolayers using dialdehyde (glyoxal) lead to the formation of 2D networks. Pronounced contraction in the area occurred for 2D OCL films in dependence of surface pressure and time indicating the reaction progress. Cross linking inhibited crystallization and retarded enzymatic degradation of the OCL film. Altering the subphase pH to ~2 led to cleavage of the covalent acetal cross-links. Besides as model systems, these reversibly cross-linked films are applicable for drug delivery systems or cell substrates modulating adhesion at biointerfaces. N2 - Ultradünne Filme/Beschichtungen aus semikristallinen oligomeren Makromolekülen sind für medizinische und pharmazeutische Anwendungen von Bedeutung. Dabei kommt der Materialoberfläche eine besondere Bedeutung zu, da diese die Interaktion mit dem umgebenden biologischen System ermöglicht. Zur Modellierung der Oberfläche werden 2D Systeme und ultradünne Filme verwendet. Herkömmlichen Techniken zu deren Präparation wie Spin-Coating oder Dip-Coating haben jedoch Nachteile, da sich die Morphologie und Kettenpackung der erzeugten Filme nur sehr bedingt kontrollieren lässt und sich die Adsorption auf dem verwendeten Substrat auf das Verhalten der Filme auswirkt. Zum Ablösen oder Übertragen der mit Hilfe dieser Techniken hergestellten Filme sind zusätzliche Opfer- oder Transferschichten erforderlich. Zudem können mit diesen Methoden nur freistehende oder selbsttragende Filme von sehr geringer lateraler Ausdehnung hergestellt werden. Das Ziel dieser Arbeit ist es, Kristallisation, Schmelzen, Abbau und chemische Reaktionen in ultradünnen Filmen von Oligo(ε-caprolacton)en (OCL)s mit unterschiedlichen Endgruppen unter Umgebungsbedingungen zu untersuchen und zu kontrollieren. Dazu wurden ultradünne Filme an der Luft-Wasser-Grenzfläche mit der Langmuir-Technik erzeugt. Die Wasseroberfläche erlaubt eine ungestörte Bewegung und Aggregation der Oligomere, was, im Gegensatz zu festen Substraten, dynamische physikalische und chemische Interaktion der Moleküle miteinander ermöglicht. Die Langmuir-Technik erlaubt mit Hilfe von Parametern wie Temperatur, Oberflächendruck (π) und Fläche pro Wiederholheinheit eine kontrollierte Manipulation der Oligomere. Kompressionsiothermen, Brewster-Winkelmikroskopie und Grenzflächen-Infrarotspektroskopie halfen beim Nachweis morphologischer und physikalisch-chemischer Veränderungen im Film. Die ultradünnen Filme wurden über das Langmuir-Schäfer-Verfahren (Kontakt mit Substrat in paralleler Orientierung zur Grenzfläche) auf Siliziumsubstrate übertragen. Danach wurden die übertragenen Filme mittels AFM und optischer Mikroskopie untersucht und mit Filmen an der Wasseroberfläche verglichen. Die teilkristalline Morphologie (Lamellendicke, Kristallzahldichte und laterale Dimension der Kristalle) von Polymerfilmen kann durch die chemische Struktur der OCL-Endgruppen (Hydroxy oder Methacrylat) und durch die Kristallisationstemperatur (Tc; 12 oder 21 °C) oder die Fläche pro Wiederholeinheit beeinflusst werden. Die Kompression auf eine sehr kleine Fläche pro Wiederholeinheit von ~2 Å2 führt zur Bildung eines hochkristallinen Films, der aus dicht gepackten Einkristallen besteht. Eine Synthese von derartigen Filmen im cm2 Maßstab ist mit herkömmlichen Techniken nicht möglich. Nach Übertragung auf eine feste Oberfläche behielten die teilkristallinen Filme ihre Morphologie, während amorphe Filme das für Polymere charakteristische Entnetzungsverhalten aufwiesen. Die Schmelztemperaturen (Tm) von OCL-Einkristallen an der Wasser- und Festkörperoberfläche waren proportional zur inversen Kristalldicke und im Allgemeinen niedriger als die Tm von PCL im Festkörper. Der Einfluss der OCL-Endgruppen auf das Schmelzverhalten war an der Luft-Feststoff-Grenzfläche am deutlichsten, wo OCL mit Methacrylat-Endgruppen bei niedrigeren Temperaturen schmolz als OCL mit Hydroxyl-Endgruppen. Das Schmelzen/Rekristallisieren ultradünner OCL-Filme an der Luft-Wasser-Grenzfläche erfolgte bei niedrigeren Temperaturen als an der Luft-Feststoff-Grenzfläche, wo keine Rekristallisation beobachtet wurde. Die Rekristallisation geschmolzener Filme an der Luft-Wasser-Grenzfläche erfolgte normalerweise bei einer höheren Temperatur als der anfänglichen Tc. Der kontrollierte Abbau ist entscheidend für die Performance von abbaubaren Polymeren als Biomaterialien. Der Abbau ultradünner Filme erfolgte hydrolytisch entweder unter saurer (pH ~ 1) oder enzymatischer Katalyse (Lipase aus Pseudomonas cepcia) auf der Wasseroberfläche oder als übertragene Filme auf Siliziumoberflächen. Eine hohe Kristallinität reduzierte die hydrolytische Abbaurate stark, aber die enzymatische dagegen wenig. Das lineare Oligomer mit Methacrylat Endgruppen (~85 ± 2 % Endgruppenfunktionalisierung) wurde bei unterschiedlichen Temperaturen schneller hydrolytisch abgebaut als das lineare Oligomer mit Hydroxyl Endgruppen (~95 ± 3 % Endgruppenfunktionalisierung). Unterschiede in der Beschleunigung des hydrolytischen Abbaus von teilkristallinen Filmen wurden beim vollständigen Schmelzen, teilweisen Schmelzen der Kristalle, oder durch erwärmen in die Nähe von Tm beobachtet. Daher eignen sich Filme aus dicht gepackten Einkristallen als Barriereschichten mit thermisch schaltbarer Degradationsrate. Chemische Reaktionen in ultradünnen Filmen können angewandt werden, um funktionalisierte Moleküle zu verbinden und ihnen Stabilität zu verleihen oder Stimuli-sensitive Vernetzungen zu erzeugen. Hier wurden die Reaktionen der Endgruppen transferierter Einkristalle auf festen Oberflächen und amorphen Monoschichten an der Luft-Wasser-Grenzfläche untersucht. Da die Kettenenden defekte in den Einkristallen darstellen würden, werden sie bei der Kristallisation an der Kristalloberfläche angeordnet. Die Dichte der Endgruppen ist umgekehrt proportional zum Molekulargewicht und daher bei Oligomeren besonders hoch. Hier wurden mit Methacrylatendgruppen versehene OCL Moleküle verwendet. Diese Gruppen können chemisch weiter umgesetzt und für eine Funktionalisierung der Kirstalle verwendet werden. Dies wurde fluoreszenz-mikroskopisch nach der Reaktion mit Fluoresceindimethacrylat nachgewiesen. Das thermische Schalten (Schmelzen und Umkristallisieren) von Fluorescein-funktionalisierten Einkristallen erzeugt eine temperaturabhängige Verteilung der chemisch verknüpften Fluorescein-Einheiten, die sich auf den Oberflächen der Kristalle ansammeln und beim Schmelzen der Kristalle homogen dispergiert werden. In amorphen Monoschichten an der Luft-Wasser-Grenzfläche führt die reversible Vernetzung von Hydroxy-terminierten Oligo(ε-caprolacton) Monoschichten unter Verwendung eines Dialdehyds (Glyoxal) zur Bildung von zweidimensionalen (2D) Netzwerken. Bei 2D-OCL-Filmen trat eine ausgeprägte Kontraktion der Fläche in Abhängigkeit von Oberflächendruck und Zeit auf, was den Fortschritt der Reaktion anzeigte. Die Vernetzung hemmte die Kristallisation und verzögerte den enzymatischen Abbau des OCL-Films. Eine Änderung des pH-Wertes der Subphase auf ~2 führte zur Spaltung der kovalenten Acetalvernetzungen. Außer als Modellsysteme wäre der Einsatz dieser reversibel vernetzten Filme für den Einsatz als Drug-Delivery-Systeme oder als Oberflächen zur Steuerung der Adhäsion von Zellen möglich. KW - polymer KW - poly(ε-caprolactone) KW - 2D material KW - ultrathin film KW - single crystals KW - crystallization KW - melting KW - degradation KW - hydrolysis KW - reactions KW - substrate KW - end-groups KW - hydroxy KW - methacrylate KW - Polymer KW - Poly(ε-caprolacton) KW - 2D-Material KW - Beschichtungen KW - Ultradünne Filme KW - Einkristalle KW - Kristallisation KW - Schmelz KW - Abbau KW - Hydrolyse KW - Reaktion KW - Substrat KW - Hydroxyl KW - Methacrylat Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:517-opus4-542108 ER -